ProBook 4530 s BIOS update fails - "...". the computer is not connected to the external power supply. »

Similar Questions

• How to use the external power supply on Camileo s20

  How the external power is connected to S20 and registration is possible at the same time. When the USB is plugged into my camera it will not turn on.

  1. open the battery cover
  2. remove the battery
  3 connect the usb power cable

  Now you can use S20 with external power without draining the battery.

  Crazy but true...

• Security concerns about the external power supply connected to the my map of 9401 TTL inputs

  I have an external power supply (5V DC, 500 my) that I use to test my card 9401 count entries and check my LV code is working properly. Power + 5V is used as high signal and ground as a weak signal.  I haven't done the link yet because I wanted to know if there is any concern to burn my card.

  Hello

  Normally, if everything is OK, it shouldn't be a problem.

  But in the real world "things" happen

  My Advisor is to add resistance series (in this case 1 k) to protect your device if Murphy enters the room something goes wrong.

• Tecra R10 - 10J: BIOS update abandoned "this computer is not supported.

  Hello

  My laptop is a Tecra R10 - 10J PartNumber PTRB1E-00D002FR, 1.40 BIOS version 11/13/2008.

  I recently bought and installed two modules of 4 GB RAM (8 GB). Enter the BIOS setup, I found 8 GB. Windows 7 64 bit also detects the 8 GB, but uses only 3.80! MemTest and diagnosis of CPU - Z are good for all of the 8 GB. I went from RAM modules from one location to another, but nothing has changed. If I replace a module of 4GB by a 2 GB memory, Windows 7 uses 5.80 is going well. Same result as any module of memory of 4 GB or slot I use.

  I suppose that problem comes from the BIOS. The 1.40 version does not support memory mapped IO functionality.

  So I followed the instructions on "http://fr.computers.toshiba-europe.com/innovation/?download_drivers_bios.jsp?" to find the last good package to update BIOS for Tecra R10 - 10J. I downloaded and ran the BIOS310?. exe, but received the error message "this computer is not supported"?

  Can someone tell me how to upgrade my BIOS or did someone has a better idea to activate the full 8 GB of RAM support?

  Thank you for all!

  Axel Limousin

  Hello

  You must install the VAP (value added package) or if this package is already installed, you must reinstall/upgrade to update it.

  Disable the Antivirus software and disable things of security such as firewalls etc.

  Hope that you're lucky...

• Portege R700 Bios update problem - this computer is not supported

  I tried the update for Portégé R700 Bios with Toshiba Service Station and by downloading the exe of the bios.
  Both say that "this computer is not supported", but the downloaded bios file is correct.

  What should do?

  Hello

  Go to the page European driver Toshiba and download the BIOS package manually.
  Unzip the BIOS and try to run the exe file once more

  But why you need BIOS update? Have you noticed a few problems with the laptop?
  BIOS update is not required if you don t have problems.

• Qosmio X 500 stop during the game - but only on the external power supply!

  Hello.

  Since I updated my BIOS to 2.9 I had this HUGE problem. And now, I created a user here, in the hope of my colleagues advice owners of Toshiba.

  Let me cut it, as it's enough for me confused.

  I bought the computer in March 2010 - is still under warranty.
  I updated the BIOS from 2.8 to 2.9. I always kept my computer up to date with the latest drivers Toshiba - and is still.
  But now, after update BIOS, all of a sudden, my computer shuts down, rotates instantly, as if someone pulled the cord and there is no battery attached.
  But it happens that whenever I start a GPU really requiring program/application. It is not happed when I use the computer for all the days of the things or watch movies etc.

  I put it well 3DVantage and of course, it crashed.

  BUT!

  If I pull the rope and let it run on battery - even if the performance that comes out is less - it does not crash, never, in any game that would break if I had the string attached.

  I was in touch with Toshiba service in Scandinavia - I live here and they couldn't tell me what was the problem, but they were pretty sure that it was not related to the BIOS, because while I was talking to them, I installed 2.8, and it's the same thing.

  It has been sprayed, treated and some more with compressed air, and if there is no dust left, it would be like concrete. I ran the game in windowed mode, while having Speedfan running, the temperature will never be greater than 65 degrees Celsius. So it isn't heat related.
  I used 3DVantage to test the CPU and see if that too would break, once again nothing.

  I think the long terms of workload. The GPU goes off when the workload exceeds a certain percentage/voltage/whatever and something in the BIOS which controls it, changed or left unchanged and there for is not skilled with the rest of the updates to the BIOS.
  Or maybe the problem is not BIOS related? is it something else? I'm really confused and the fact that I can use it for simple tasks, only confuses me even more - so this is only a part of the graphics card which is damaged?

  Even if it is under warranty, wait 10 days (if I'm really, really lucky, like place I bought it, is not exactly known for good service condition) is the last option.

  This explanation is rather long, but I'm not not short versions, and if you feel like I left something, say so, and I'll do my best to provide you with information.

  Thanks in advance!
  Nikolaj.

  Post edited by: n_larsen - typos.

  > Speedfan shows also a tab called Temp1 - ACPI... It may be offtopic, but what is?
  When I order the windows event log, it shows some errors about ACPI: (translated by myself from Danish)

  Advanced Configuration and Power Interface (ACPI) specification is an open standard and defines independent interfaces for hardware discovery, configuration, power management and monitoring.

  66 temperature is not too high so I n t think that automatic shutdown of the bottom are related to temperature.

  I have your case, I recommend reinstalling the OS window once more; install the operating system preinstalled Toshiba using the recovery disk.
  Then check the features of the laptop. I mean that you should not install any other software before checking the laptop. In many cases 3rd party software could lead to problems of different laptop then you should check the laptop using factory settings.

• P0.0 6516-setting PCI to high causes the voltage drop across the external power supply

  Hello

  I use a PCI 6516 for 24V output. I have my power supply connected to pin 5 positive cable and the negative to pin 19. When I put the port 0, line 0 (P0.0) high heat, I have a voltage drop on the power supply to about 1.9V. There is no other son so there is no short circuit anywhere. The rest of the lines work very well when I put them on high. The automatic test works very well, and I tried to reset the unit several times. Could there be potential damage to this specific port? All the solutions to this problem, or anything that may have caused this behavior?

  Thank you
  Ahmed

  
  

• BIOS update failed: the process does not have this system. The process of the utility is not complete.

  I have a Thinkpad T450s and I'm trying to update the BIOS version 1.19 to 1.20. I've created a live usb with the 'el tortio' - image extracted using linux "dd". Once I boot on the USB under Legacy-BIOS and select upgrade, it proceeds witht the error message "the process does not have this system. The process has been cancelled. "I have disabled the protection against theft, AMT (I think this is the option) and I'm sure that I use the correct .iso file from the downloads section. I don't have a Windows operating system installed, but I'm able to start in various linux distributions using Legacy and UEFI methods.

  Here is my BIOS information.

  "Manage 0 x 0031, DMI type 0, 24 bytes.
  BIOS information
  Seller: LENOVO
  Version: JBET54WW (1.19)
  Release date: 06/11/2015
  Address: 0xE0000

  Runtime size: 128 kB
  ROM size: 16384 KB
  Features:
  PCI is supported
  PNP is supported
  BIOS is extensible
  BIOS shadowing is allowed
  Boot from CD is supported
  Selectable boot is supported
  ACPI is supported
  Legacy USB is supported
  BIOS boot specification is supported
  Targeted content distribution is supported
  UEFI is supported
  BIOS version: 1.19
  Firmware revision: 1.2 "

  What could you suggest to get the update disc to recognize my system?

  I think I've fixed the problem, I formatted FAT16 USB drive and not in FAT32 and also when you use the geteltorito command, it is preferable to use the-o option rather than a redirection ">"syntax. " An article said that it is best to drop in a DOS command line using the USB boot, then run dosflash.exe from there, however, I could not edit the .bat file, but it is an option however.

  I hope this helps someone stuck in a similar situation.

• mouse jumps touchpad cursor so that connected to the external power supply and works perfectly when operating on battery

  When I'm running my cursor cannot be controlled. When I shoot taking everything goes well with the pad and cursor

  Hey, it seems to be ok now! Thank you

• Satellite L755-S5349 - BIOS update failed - black screen

  Hello.

  So yesterday, I got a Toshiba pop-up message to update my BIOS, so I clicked it and it started to update but then it says "error checking".

  So I closed it, cause I had to restart my computer after one previous update with another program and I thought to try to update the BIOS after you restart.

  But once it restarted it is off, so I tried to put back market but the screen is black, lights are immediately (food, batt etc.) and the fan works just as well. I tried to take the battery out and in again but screen remains black.

  Could someone please tell me what you think it might be and what I have to do.

  I also tried with a HDMI, but it does not recognize.

  Thank you for your help

  Hello

  I think I have bad news for you.
  To me, it seems that the update of the BIOS didn't
  Why? Who knows maybe that some applications that runs in the background affected the BIOS update process.

  I've updated the BIOS on my laptop last night, everything went well. First, I downloaded the BIOS package from the Toshiba page. Then I unzipped the folder.
  I closed all applications that looked like Firewall, antivirus etc software
  Then I did the BIOS update

  At least in cases where the BIOS update failed, you must get in touch with a local ASP Toshiba in order to solve this problem in the best of cases they need to update the module ROM again

  Good luck

• Vostro 3500 BIOS update failed - need recovery procedure

  I got a Vostro 3500 laptop computer work and was doing maintenance to update. I downloaded and installed the BIOS update recommended for this laptop... Dell Vostro 3500 system BIOS 3500 has 12. EXE | Release date of BIOS of Windows/DOS (3 MB) 21/07/2014 updated 21/07/2014 recommended BIOS update failed and left no work of BIOS of the computer. F2 is dead. It will not start. I am sure that there a backup BIOS or primitive still, as when I start the machine without battery and power, using the end key he's constantly trying to read the data from a 2 GB flash drive. I guess he wants to reload the BIOS from a file. I know how to get the ROM content from the file above using the /writeromfile parameter. The big question is, what type of file the 3500 wants to read, and what is the name of the file it is seeking? Is the flash player must be bootable? What is a FRIEND or a Phoenix BIOS? Can someone please? Thanks, Terry

  Here's how to recover a flash update BIOS of your laptop Vostro 3500 failure...

  1. download the Dell BIOS update .exe file to a USB flash drive.

  2. run the .exe with the /writehdrfile parameter file

  3. run the .exe with the /writeromfile parameter file

  4. copy the .hdr winery50.hdr

  5. remove the battery and the power of the dead computer

  6 Insert the flash drive into the USB port on the computer of the death

  7 press and hold the end key and then connect the AC power

  8 dead computer reads USB flash and request if the update should be performed

  9. let the update at the end and then restart.

  10. computer now works normally.

  Useful web site: http://mickitblog.blogspot.com/2011/09/dell-bios-switches.html

• BIOS update failed on Tecra R10 with Windows7

  Hello

  I have problems with the update the BIOS of my Tecra R10J. The current version is 1.4, and I want to upgrade to 3.0, so I downloaded from the Toshiba web site the good file named "P006Cv300.exe" 2009-11-04 released. It is an update of the BIOS online in a real session of Windows 7. Simply right click the compress exe, click Run as admin and that is all, but... for me, he said:
  * "[Error] the start of the service was abandoned. The user doesn't have administrative privileges. "

  See below:
  http://perso.Orange.fr/100Mo/bioserror.jpg

  I tried with:
  -closed AV, firewall, etc...
  -turn off UAC
  -Run as administrator
  -Tried with another admin account
  -Safe mode (update of the bios doesn't support safe mode)
  -lead the local administrator session

  No change. Always the message "user lacks administrative privileges."
  Need help please, found nothing on Google (similar but not resolved Bios problem!)

  Thank you

  Hey ignore them,

  As Akuma has already written the added value Package must be installed for BIOS update for the BIOS to read system information correctly. Besides, the VAP is needed for special functions such as the FN keys so it must be installed.

  It would be interesting to know what is happening with the factory settings. I guess that your computer laptop wasn t ship with Windows 7, but with Vista and you should try it with Vista.

  Welcome them

• BIOS update failed on Satellite P200 - 13 M

  Hello world

  I have a Satellite P200, (PSPB6E-03G01XFR).
  Yesterday, after attempting to update my BIOS version with the windows application, my phone was cut.

  I downloaded the new version of the bios of Toshiba-Europe Web site (v2.30) and I tried to use the Crisis_Recovery_Disk but no result. :(
  Can someone help me please?

  Unfortunately, in your case only the ASP can help you.

  Does your BIOS update fails and only the ASP can update the ROM module damaged by using a special version of the BIOS

  So, don t waste time and ask the ASP in your country to help.

  Best regards dude

• BIOS update failed - where can I download BIOS for floppy drive?

  Hello

  After the BIOS update fail by Windows I need to reflash.

  Where can I download the bios for floppy drive files '?

  Thanx

  Hello

  Update of the traditional BIOS cannot be downloaded.
  Only focused on winning BIOS is available on the European driver Toshiba page.

  In your case, you will need to contact a local ASP.
  The technician can help you and able to reflash the BIOS using a disc of crisis of the BIOS.

  Good luck

• Satellite L40 PSL48E - BIOS update fails on VISTA 32 bit SP1

  The 2.0 with latest downloads BIOS update failed.

  After adjustment of the rights of the user and Disabling UAC is remaining the following command line error:

  C:\TEMP\BIOS>winflash.exe P20B200. BIN
  Cannot copy the BIOS image. (File name error?)
  C:\TEMP\BIOS >

  No idea how solved it, file name is correct?

  You unzip the package to update the BIOS first?
  It is very important that the BIOS package will be unpacked first.

  Then, you can update the BIOS the winflash.exe execution.