ProDesk 490 G2 MT: POST error after upgrading the BIOS/UEDI: "incorrect chassis serial number.

Similar Questions

• Tecra M7: Various errors after upgrading the BIOS version 3.30

  After that I updated my bios to 3.30 I have the following problem:

  -A edge wireless turns off after a while and can not be activated until I restart.
  -Battery information is wrong. I tested the system, I can use 1 hour after he said that my battery is 0%

  How can I solve this problem? I have to downgrade my bios version?

  Kind regards.

  Hi mate,

  Let's see if my advice would be useful for you:

  1. try to reinstall the driver by downloading the latest version of the driver on the Drivers Toshiba download site. What you could also try is to disable the powermanagment for the wireless network adapter. (Just go into Device Manager, find the wireless card, and that there should be an option with a checkbox to disable)

  2. it's really rare, never heard talk about this issue. One idea would be to change all the parameters powersaver to your machine so that the battery will empty without entering in the day before etc... Just let the machine work until the battery is empty. Then remove it for about 1-2 hours, reattach and start windows. The battery should indicate 0% and then you leave the machine to load the battery. (the machine must be turned on). I hope that the battery must show it s correct percentage after you complete these steps.

  Welcome them

  PS: Please write again if it worked

• Error after upgrading the BIOS on Satellite A200 (PSAE0)

  My Notebook: Satellite A200 (PSAE0) with Windows Vista.

  When I try to update with the utility setup.exe (BIOS version 1.80 - WIN, compatible for portable computers with Windows
  Vista!), it goes all the way to new BIOS then the machine is blocked, collapsed.

  I have to remove the battery to turn off the power of the machine to restart. But the does'n system start and does' screen n

  turn it on...

  Can anyone help please?

  > Did you know BIOS is fixed on the motherboard?
  Not the BIOS is fixed on the motherboard, but the ROM module is fixed on the Board!

  Please don t try to correct yourself because you can really damage the jury!
  And as you've probably experienced the motherboard is one on the most expensive laptop parts.
  Notepad allows you to checked by a technician with experience of the computer laptop and don't try any dangerous experiences it s not worth!

• HP EliteBook 745/755/725 G3: Missing 'Label restore electronic tool' to fix the POST error boot in the BIOS 1.08

  The latest BIOS for the HP EliteBook 745/755/725 G3 made reference to a 'restoration tool electronic Label' to remove a MESSAGE error after flashing the BIOS to 1.08.

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=7815285&swItemId=ob_160552_1&swEnvOid=419...

  According to the release notes: "NOTE: for systems that do not comes with BIOS version 1.05 or later, this utility may be required if the BIOS has been updated.» Visit the page of the BIOS and drivers on www.support.hp.com and follow the instructions using the Restore tool from HP on the electronic label. »

  This tool can be found on the support Web site.

  If flashing the BIOS is causing this problem for systems shipped with a version of BIOS before 1.05 why is the tool not available to correct the problem?

  Better question is why was - this BIOS update published at all if it can cause a system to stop for 15 seconds during POST if you do not have the correction tool POST message as described in the release notes and the POST message?

  Version 1.01 of the electronic Label restore tool has fixed my problem.

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_162255_1&lang=en&cc=us&hprpt_id=HPGL_ALERTS_1873677&JumpID=em_alerts_us-us_Mar16_xbu_all_all_641843_1873677_LaptopsandHybrids_routine__/

• Satellite L650d-120 does not load after upgrading the BIOS 1.7

  After upgrading the Bios up to 1.70 my laptop is no charging current, but always works to the AC adapter.
  Can I do something on my own?

  Hello

  First of all, you should set the BIOS to default settings and need to save the changes.
  You must also leave the AC adapter plugged into the laptop for a longer period of time.

  Welcome them

• After upgrading the bios to version 2.13 t430u, it freezes at black screen

  Hi all

  After upgrading my lenovo T430u bios to version 2.13 it freezes at a black screen, and windows does not load. My machine has windows 7 Professional and the only way to make it work is to reset the bios settings, but after awhile, it freezes at black screen and windows 7 does not load again and need to reset the settings of the bios once more. Hope someone of you gyus can help me with this since is very frustrating.

  Lenovo has released a BIOS updated for ThinkPad T430u that resolves customer reports of black screen after upgrading the BIOS.

  CHANGES IN THIS VERSION

  Version 2.15

  [Problem resolves]

  -Fixed a problem with the black screen after BIOS update

  -Fixed a problem with the gray screen when turn off Bluetooth in the BIOS Setup

  V2.15 BIOS can be downloaded here: http://support.lenovo.com/us/en/downloads/ds031724

  Thank you

• Bluetooth not available after upgrading the BIOS on HP g62-a60EM

  After upgrading the BIOS, I can't use bluetooth, as I can't see it in Device Manager. I've updated the BIOS with the file sp55430 on the support site. Battery is not holding a charge, it runs out after about 30 minutes. Back BONE back then now, I can use bluetooth. My OS is Windows 7 Professional 64 - bit - Slovenian.

  If anyone can help?

  Kind regards

  Dragan

  Hello

  Try to update the BIOS again. After that make sure that the wireless and Bluetooth lights is lit. Also download and installed the drivers of bluetooth and verification.

  After the BIOS also check in BIOS if Bluetooth is turned on:

  Menu of the System Configuration > Integrated device options > Enable/disable integrated Bluetooth Radio device
  

• Satellite L50-B-177 - after upgrading the BIOS can not use the Polish symbols

  Hi, I'm newbie here. This is my first post, so sorry for the plain text.

  I have a problem with the laptop Satellite L50-B-177 1 month of my wife. After update BIOS (from Toshiba Service Station) to version 1.70 I have this problem: it is impossible to use symbols of Polish that comes with ALT + z, ALT + x, ALT + c. other - ALT + a - works normally.

  Problem is the operating system independent (even on the live session of Ubuntu). I understand that this is a specific problem for the location of the Poles, but causes cell useless for my wife (she is a teacher and write a lot of text). As much as I know BIOS downgrade is not available for customers, and the weeks of waiting for the new package of BIOS is out of the question.

  Any suggestions will be appreciated.

  Hello

  This problem occurred imadiately after updating the BIOS?

  Have you tried to set the BIOS settings by default once the update is complete?
  If this isn't it.

  Also, check if the Polish keyboard language was chosen correctly and as a default value.

  Comments are greatly appreciated.

• Laptop computer DV6174ea not start after upgrading the bios!

  HP dv6174ea lapop - Win XP media center edition with sp3 - processor intel core duo - 2 GB ram - 120 GB hd

  Ive just used the upgrade of bios of HP downloads flash to upgrade the Phoenix bios on my dv6174ea to version 2.9 1.06.Flashed successfully but on reboot it reaches windows XP start screen (black with logo) fails then a blue screen and restarts quickly. Same cycle occurs again and again. Ive tried to boot from the XP cd, but it gives the message "no hard drive not detected" and fails. detect the drives in the BIOS there is no options to the automobile.

  Curiously, a USB bbot containing paragon hard disk manager won't start and sees my drive (two partitions) and the system partition is active.

  I wonder if the flashing the BIOS changed settings or drive letters so that windows does not see properly. I wish there was just a simple option in the bios for detection of discs.

  Can someone pls help.

  If you want to start your computer from the xp cd, then enter the bios and it try to disable the sata mode and activate the ide mode and then try to format your drive... it should work... !!!

• No GPU fan after upgrading the BIOS to 4.2 on Satellite P100-434

  Hi, I upgraded my BIOS today to version 4.2 and since the GPU fan only works during the splash screen, and once Vista has loaded, it never runs again, in addition, the CPU fan turns at a constant speed, and the screen has "shifted" to the right, so I quarter of the right hand of the screen on the left.
  As you can imagine, it's a little annoying, and to say that the GPU temp is 65deg. with 90deg all about processors. not too good for the material.

  Is could someone PLEASE tell me how I can downgrade the BIOS?

  I have fans and fences etc. are all and free from dust.

  I do turn all the appropriate toshiba of specific drivers, and I even tried to reinstall the NVidia one card.

  GeForceGo N-Vidia 7600

  Thanks in advance.
  Jack

  Someone else here had the same problem, according to the P100 support newsletters found here http://www.csd.toshiba.com/cgi-bin/tais/su/su_sc_modSel.jsp you must update the nVidia Driver If you update BIOS v4.2

  Here is what says the newsletter:

  *
  Update the BIOS of the computer to the version 4.20 or newer:

  1. click on the following link to download the BIOS version 4.20 for Satellite P100. Save the file on the Windows desktop.

  You can also search for a newer version of this BIOS on Service and assistance from Toshiba site at support.tosiba.com.

  2. double-click on the file sp100v420.exe on the Windows desktop to start the driver installation.

  3. restart the computer.

  *
  Update the display of the computer to version 7.15.11.5666 or newer nVidia Driver:

  1. click on the following link to download the version of the nVidia 7.15.11.5666 display driver. Save the file on the Windows desktop.

  You can also search for a newer version of this driver on Service and assistance from Toshiba site at support.tosiba.com.

  2. double-click on the file driver_display_nvidia_os2007387a.exe on the Windows desktop to start the driver installation.

  3. restart the computer.

• Laptop not start after upgrading the BIOS crash

  Hi all

  I just want to ask if there a chance to reactivate my Satellite A300 after crash BISO update without it sends to the service of Toshiba.

  I downloaded the new BISO and he started in the Windows menu. After a few seconds my PC crashed and everything was frozen.
  I turned off the PC.
  Now, when I press the power button to boot up the laptop, the screen is black and I can a sound BRR, BRR, BRR of the CD-Rom drive.

  Don't you think that it is possible to boot from a CD or something like that. Is it possible to reactivate my phone?

  Your help would be really appreciated!

  Thank you very much

  Best regards

  Chotte

  Sorry but if the BIOS chip is damaged there is not a lot, you can do about it. You must contact the Toshiba authorized service provider.

• Satellite A300 - BIOS downgrade after upgrading the BIOS

  I did an upgrade of BIOS of victory of version 1.6 of 2.10 - at the recommendation of the Toshiba site, for my laptop A300 1N0 - model PSAGUE.
  Touchpad no longer works. I have 2 operating systems, XP and W7 is the same.

  I start the laptop with the Windows Live CD and Ubuntu Livecd and nothing has changed.
  The mouse works, but the touchpad is still dead.
  Any advice?

  How can I find the old version of the BIOS to do a downgrade?

  Try contacting the Toshiba authorized service provider in your country. They have access to the database of Toshiba and the access to the Archives of BIOS.
  I'm sure that they can send you old BIOS version and you can downgrade BIOS on your laptop.

• Equium M40X does not work properly after upgrading the BIOS

  OK, well... I'm not a computer scientist, but I have a bit of trouble on my hands and I don't know where to go for the right help, so I came here.

  Today I started my lappy to confront an illuminous Green Office... not all it is green just of great spots here and there. Happened to me before, but it disappears after about 15 minutes, but today his guarded it usually hours and is still as he.

  I looked everywhere on the net for a possible fix but nothing helped, even though I've heard somewhere that an update of the BIOS might do the trick, so natually, I did... I came here and searched for my Equium M40X, found, downloaded and installed the latest version...

  but now I have a screen with a resolution of half of what it should be, it went from 1200 x 800 or something like that... to 1024 x 786 and I always get the green screen problem... the program toshiba provided for the update of the BIOS does a backup file (BIOS. (BAK)...

  I can't restore the old BIOS would set the screen resolution, but I'm just helpless as to how I go about it. I find the file, but I have no way to open/run it

  I've had this laptop for about 2 years now, I know probably just getting old and a bit tempermental, but if theres no way you people out there can help, I would much apreciate it :)

  Thanks a bunch - Ash

  Hello

  I Don t think the biosupdate is the reason for the reduced screen. It does not sound like a software thing, but rather a hardware malfunction.

  Is your normal screen during startup? If so, I'd say just remove your existing display drivers and install the new. But if it s like you described then it must be a hardware problem and the machine should be checked by a technician or at least a service partner.

  Would be better if your bring your machine to an ASP for a checkup of material.
  If you need assistance to find the ASP closest, try this link (the ASP index):

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT

  Welcome and good luck

• Satellite P200 - option SATA missing after upgrading the BIOS

  Hey guys!
  First sorry for my englich
  So I have a toshiba satellite p200 1jy upgrade the version of the bios (Phoenix bios) 2.70, but when I update upward I don't have the option of ahci sata or ide mode, I do not have this option, but I had before upgrade,
  so please what can I do to switch to ahci or ide mode, can I downgrade the bios version

  So thank you we

  Hello

  Must add driver SATA while installing Windows.
  During the installation process you will be asked to add the driver (F6 key)
  Then you could add the connected USB floppy disk driver.

  More details how to do here:
  http://APS2.toshiba-tro.de/KB0/TSB7B020R0000R01.htm

  or here

  [How to integrate the AHCI driver when installing Windows XP | http://aps2.toshiba-tro.de/kb0/HTD9401AN0000R01.htm]

• T530 does not start after upgrading the bios to V2.65

  Hello..

  I flashed the Bios to V2.65 under Win 10 via Lenovo Systemupdate.

  After the restart I had set default Bios and save the changes.

  Start the laptop it hang in a window to select the boot device.

  When I press on my Samsung SSD EVO nothing happened.

  I'm trying to reinstall the Bios with boot-CD. Tool said: there is no need, organic cause is real.

  Downgrade to old Bios in possible (?) not...

  It please can someone tell how to fix this?

  It comes to my work machine, and this is a disaster!

  Thanks MajorM

  Hello..

  found the solution...

  > Disable menu security-> "secure starting".

  > Start menu: UEFI/Legacy Boot-> legacy set or both

  too long, I remember. I never had problems with the bios updates.

  but it was my last... never touch a running system

  See you soon...

  MajorM