PS4000 firmware update failed

The event ID: 30.4.1 table firmware version V6.0.11 for 7.0.1 update failed. Reason: Another copy of the update is already running. .

I'm moving to 6.0.11 to 7.0.1, so I can add my new ps6100 to the group.  FTP seems to happen when I do the mistletoe group management.  But when it gets to step 2 from upgrade fails before reaching 1%

My other set ps4000 up-to-date without problem.

Any thoughts?

Gift of greetings,

This problem has been resolved.   It was a problem with the controller, the controller had been for more than 500 + days.  This support has me initiate a reboot on the controller, once it was full, I ran the upgrade to 7.0.1 of the other controller without problem.  Then I switch to 7.1.5 to match new hardware, I install and when new material is attached to the group I will switch to the current 7.1.X

Thanks for the help

Tags: Dell Tech

Similar Questions

  • BlackBerry Smartphones ARM11: Touchscreen firmware update failed

    Please I need urgent help.

    I have connected my 9520 Storm to my computer and blackberry desktop manager told me that I had an update. So I decided to update. During the update process, when he says to connect my camera to the JAVA virtual machine comes up with the following error.

    ARM11: Touchscreen firmware update failed

    Device error: 302

    Has no task: INPUT_SYS

    Files:

    Line: 0

    SP = 0X1784EAF0

    LR = 0X16119DD9

    PC-0X16118A90

    I tried to reinstall the operating system of all possible ways. From loader.exe, Office Manager, but I find myself coming back to this same error message.

    Please, I need emergency aid. Please...

    Hello SmoothRider,

    Thanks for the reply but I was able to get the ot to start work. I had the phone screen has changed, and immediately I put in the battery, that I was asked to reload the software I did and tadaaaa... It worked all fine again. I guess that the error had something to do with the material for the screen.

    Thank you

  • Portege R400 - Firmware update fails for 3G card

    During the Firmwareupgrade of the G 3 embedded (expedite EU870D) in my protégé R400 card, I have a power fail. The next time you start, I can't countinue with the upgrade. The card no longer works.

    The Modem and the COM Ports, I don't see in Device Manager. Is there a solution for this error? Thanks for the help!

    Pumbkin

    Why do the update of the firmware?
    You should do this only if the Vodafone SIM card does not work properly!

    I found this info that pop ups before performing a firmware update!

    + Atten-tion of the FW update: +.

    + Please do not forget to read carefully before place the FW. +

    + 1. FW update is not necessary when the Vodafone SIM card works fine in the customer environment s. run the FW update only when the Vodafone SIM card is not detected. Please note that the FW is more reversible to the previous state once updated. +

    + 2. This upgrade tool will apply to the following models with built-in 3G module: +.

    + Portege R400 +.
    + Portege R500 +.
    + Tecra M9 +.

    + 3. Please leave 3G communication and close the connection utility before running the FW update. +

    + 4. Close all applications before you run the FW update. Please DO NOT launch any application during the upgrade process. +

    + 5. Please ensure that you use an AC adapter to power the computer during the process of FW update. Power failure during the upgrade process can lead to failures of 3 G modem. +

    + 6. Please DO NOT sleep/standby extended/Shut Down the computer during the process of FW update. This can lead in mode 3G +.

    So please first these points before you is trying to update the firmware!

  • P1102w firmware update failed

    Hello.

    I tried to update the firmware for HP P1102w, and he seemed to be omitted. After waiting for a long time, he ended up with the error message, "restart the power of the cycle, and then try again" or something like that.

    After that, he does not appear in my network, and I lost the web interface and the print function. My rounter does not show its presence. The printer has solid purple lights on the WiFi and the triangle of light.

    I tried to do a factory reset, but I could not find.

    I understand that the firmware has failed is critical. Someone knows how to fix this?

    Thank you very much.

    Hi ttanemori,

    Please connect the printer to your computer via a USB cable, and then restart the update of the firmware.

  • Sansa Firmware Updater fails to install on my PC

    Hello world

    I can't install the update on my pc.

    This is what he wrote when it fails: "Downloding last sansa updater...»    X '.

    "The installation fails. "Please try again later".

    I have tried many times in the past 24 hours and its still the same.

    My pc is clean no viruses, spyware, etc., well maintained, firewall does not block it.

    Any suggestions?

    Most here do not recommend the use of the update. It's a resource hog that will slow your system down and nag-ware is most of the time as whenever you plug your player will be 'phone home' looking for updates. Firmware updates are not very numerous and widely spaced and manually updated (or reinstall) updates usually takes less time than downloading and installing the update.

  • Sansa Firmware Updater fails to install every time...

    I have had my Sansa View for about 2 months now. I have never been able to install the Sansa firmware update. It seems to go through all the steps, then suddenly steps back on the "download the latest Sansa Updater" and says that failed (once just a second before this step was completed successfully). It seems to with success download it, install it, then save, then he can make another step or it may fail on the registration... I can't. All the steps after downloading disappear and now it says that the step does not and gives me the error message "Installation failed. Please try again later. "I think 2 months is much later...

    I am running Windows XP SP3 32-bit. The windows firewall is disabled and I use COMODO Internet Security and I use Avira Antivirus. I tried to disable the firewall and the antivirus just to see if they are the cause of the problem, but it has no effect on the results of the installation. In addition, COMODO logs do not show any activity blocked the Installer (or whatever it is blocked at all today). My account is an administrator account.

    Now, I think it should be noted that I don't need an update of the firmware. My player integrates the latest version from the website. What I really want is to convert my videos so that I can use them on the player. Unfortanetly there is no way to install the Sansa Media Converter without installing the Firmware Updater (ahh... how many times I tried wasn't the case... but alas...).

    Any help would be appreciated. Thank you.

    SOLUTION: I found a thread on the forum of Sansa View that describes the required parameters for the conversion of the video correctly to play on my device. (Here: http://forums.sandisk.com/sansa/board/message?board.id=view&thread.id=3300) Given that I don't need to update my firmware (and lets hope I don't) it is a perfect solution for me (especially considering the horrible things I've heard of the SCM).

  • CP1025nw firmware update failed

    Hi - I tried to update my firmware (most wireless) and get the error message failed to update and powercycle the printer and try again.  I tried several times and get the same result - update failed.

    Is there another way to update the firmware (via maybe USB?)  RFU is Enable - I think - instructions to check through GB & button yellow has not been made as indicated.

    Thank you

    Richard

    PS Windows 7 x 32

    Well...

    Has decided to 'take the bull by the horns' and remove the impressions and all HP software.  A lot of ghosts and files left behind so had to use regedit to clean up junk and the C:\system32 goto and delete all the driver files - what a mess.

    Started from scratch and utility installation found the printer and I also decided to abandon the bad software wireless connection and went with another Ethernet cable to my HP printers...

    Now this printer works - the back to try to get my LJ1022n to stop the perpetual printing from my wifes computer...

    Problem solved using brute force.

    Richard

  • The PS5000 firmware update fails

    Update firmware to 5.0.8 to any newer version of firmware PS fails!   Any ideas?

    I had to run the updates of the CLI,

  • HP9250C - Firmware update fails

    I work with a client with three 9250c Digital Sender.  We use the send to folder option and want to upgrade the firmware to make sure that the file name of the PDF file are always unique.  A technical note HP information indicates that we need 48.140.2 firmware or higher to achieve. See the attached Technote

    We have tried to install the latest firmware 48.293.1 via ftp.  The ftp commands indicate that the. The RFU file has loaded correctly, but when you return to the control panel of HP9250c that she went from 'Ready' to 'Suspended' but the firmware has NOT improved.

    The old firmware updated is 20070626 09.081.4

    Can anyone offer a solution to resolve the update.  I checked and the ability of the firmware update is enabled.

    Thank you Murray Croft

    Thank you for your comments.  You are absolutely right. I was finishing this work remotely and subsequently discovered that I had given the IP address of a 9200c rather than the IT Department of 9250c.  You're going to want to retry the upgrade today.  My apologies for the confusion.  Murray

  • Photosmart C4780: HP Photosmart C4780 Firmware Update Fail

    I downloaded the updated of the "C4700_FWUpdate_4362_HPCOM_v1" firmware, but every time I try to install the wizard says that my printer is not connected.  In fact, it is connected by USB cable and wireless.  I can print to it, printing and scanning doctor sees and checks that it is OK.  The HP Digital Imaging Monitor reports that it's OK.

    The printer is running its original software and works OK, except for the occasional low response to the control panel entries that this firmware update addresses.

    My Device Manager shows all the correct drivers OK and my control panel shows the printer OK.

    Any thoughts, please?

    You won't be able to reflash the firmware now. Looks like it is ready to be discarded. Time to buy a new printer, I'm sorry.

  • LRT224 firmware update fails

    Due to corrupted bin file, update the firmware on my LRT224 failed.

    I can ping router, but the Web page does not open.

    I tried tftp.exe, but had no success.

    Any suggestions?

    THX!

    I tried all the reset scenarios that you can find on the net, without success...

    Linksys support staff suggested to go to the store and replace the unit. Which is what I went to next Monday.

    THX!

  • the iDRAC6 firmware update failed during the process

    Hello

    One of my colleagues went to a customer who has a few problems with the upgrade of its most recent firmware iDRAC6.
    Case 1
    R710 - with firmware version 1.41-> 1.54 fails to 30%

    Case 2
    With the firmware 1.54-> 1.70 R710 - fails to 30%. Also I tried 1.54-> 1.80 fails also to 30%.

    In both cases we found no indicationin error log files. Download was fine, checksum is ok, only FW upgrade failed, but no details.
    It's a common mistake? What can we do to work around this error?

    Kind regards

    Stijn

    I finally after trying to update iDRAC 6 version 1.0.3.10 to 1.98.8 (last update of this post)

    The update (stuck) were held 30%.

    Solution is to download "firming.d6" * wait 5 minutes * before clicking on the button update to begin loading the new firmware.

    R610 server would not update unless the server has been turned off and then follow instructions above.

    If I clicked the button to update firmware soon after downloading the file, it would always fail at 30%.

  • SPA112: impossible to pass to 1.4.1 firmware (update failed)

    Hello

    I recently updated the firmware from a dozen of SPA112 to 1.4.1. Everything worked well, except one. Even after a power cycle, always reports "Upgrade failed". It displays the following system information:

    Model: SPA112, 2 FXS
    Hardware Version: 1.0.0
    Boot Version: 1.3.1 (December 11, 2013 - 11:38:47)
    Firmware version: 1.3.5 (004) July 31, 2014
    The Firmware recovery: 1.0.1 (005)
    Serial number: CBT154009VM

    I found it's my only camera with the greater than 1.0.x version of start. It upgrades only to the version of the firmware 1.3.5.

    Y at - it incompatible with the firmware 1.4.1 and the starting version 1.3.1?

    Thank you for your support.

    Christoph

    No such problems known (as I know). Make sure that the upgrade file is complete and intact (older firmware may not detect some types of changes):

    Payton_1.4.1_002_102615_1042_pfmwr.bin
    SHA256 = 595bb908e9223daafc68e0615c793bf65d3ae393b0ae77fdfe0b9d67b88f5911
    SHA1 : c3a3ebb7029e5c41333ee1d6a09ae9a2e732d005
    MD5 : 74dd18427f94bc76ae2e08bb0dbddcda
    SIZE : 9961864
    If not changed then turn on syslog & debug (highest level) and capture him during the upgrade. It may disclose the real cause of the failure to upgrade.
  • Seagate Firmware update failed

    I tried to update the firmware recommended Seagate HDD on my Optiplex 780 (from page to download drivers for my machine).  The update is Seagate ST3320413AS, file name B765JC49.zip, published on 28/06/12).  My current display device manager driver is J47 and to drive HARD Seagate model ST3250312AS.  The machine is Win XP Pro SP3, all the Microsoft updates applied.

    During the part of the firmware upgrade process is restarted, here is what I got after following the instructions for "Please wait while files are copied into memory...". DO NOT INTERRUPT THIS PROCEDURE! » :

    Model ST3250312AS SN 5VMXK2JB JC47 generic ATA PCI Bus 0 device 0

    Invalid data... 01:00

    Download the procedure has no

    Failed (in big red letters)

    I hit 'c' to return to Windows and the machine is still very well, but what could have caused this and how important is this update anyway?  I like to keep my machine firmware and drivers up to date, especially since this update is in the category '' recommended '' Dell.  Thanks for any help, Chashood

    Hi Chashood,

    Updates firmware, especially for readers, should in general be applied only if there is a specific problem which firmware was released to correct. So I recommend that you leave things as they are.

  • RV220W Firmware update fails (RV220W-Firmware - 1.0.2.4.img)

    I have previously updated the firmware on our RV220W of 1.0.0.26 to 1.0.1.0 without any problem, but all attempts to upgrade to the latest version 1.0.2.4 fails with the message following 'upgrade failed due to firmware not valid/damaged. The router then automatically restarts with the current firmware.

    We have tried to re - download and apply the update of several different machines with different operating systems and browsers without success. Anyone who manages to implement this version of the firmware successfully? We really need a some VLAN fixes included in this latest version!

    Any suggestion would be appreciated.

    have you tried to reset the router to the factory settings?

    from 1.0.2.6 requires a factory reset once you have upgraded to 1.0.1.0 then maybe this one still has a reset?

Maybe you are looking for

  • Visual Voicemail Iphone6

    I have the iphone6 and visual voicemail is currently unavailable and I can't call voicemail. What can I do?

  • Replacing the battery for Satellite NB10T-A-103

    Hi all Y at - there no replacement battery (compatible maybe?) with a higher capacity (> 2100mAh) for the computer portable satellite nb10t-a-103? the original battery only works for 2 hours. Thank you.

  • BlackBerry smartphones transfer contacts to Samsung Entro list

    People, I had a Samsung Entro with over 250 contacts and recently turned to a Curve 8530. I'm transferring my contacts list of the Entro to the BB. I tried pairing devices and succeeded, but when I tried the transfer with the BB, I can transfer only

  • How to share a program in windows 8.1?

    I recently downloaded the world of tanks MMO game, but only I, the admin could use it.  Other users (wife, two children) can not open the file.  They get notice that, indeed, that the file cannot be opened, and that they have the appropriate permissi

  • Need creative Cloud Packager - old version

    HelloWe have CC for teams and I need to build packages for Mac running 10.6.8 - but the current version of CCP (1.9.1.2) minimum needs OS version 10.7 start.Where can I download a version that starts under 10.6?Any tips?   Thanks for tips' tricks...