psc2510 work before the power failure, crashes attempt to restart only show a static hourglass

Similar Questions

• AirPlay does not work on Apple TV with ios 10.  It was working before the update.  Please notify.

  AirPlay does not work on Apple TV with ios 10.  It was working before the update.  Please notify.

  Try these steps, check to see if things work after each step if necessary, before you try the next.

  1. Check AirPlay is on the Apple TV (turn market if it already is)
  2. Check that both devices are on the same network (settings > Wifi on the mobile device and the settings > general > network, on the Apple TV).
  3. Restart the Apple TV (settings > general > restart).
  4. Restart the Apple TV by removing ALL cables for 30 seconds.
  5. Restart your router. (Also try to remove the power cord for at least 30 seconds)
  6. Restart your computer or mobile device.

  If you're still having problems, try to use 802.11n for wifi if you currently use 802. 11B or 802. 11 g.

  If your problem is AirPlaying starting a computer, try turning off bluetooth

  If you're still having problems, the following article can help you.

  Troubleshooting AirPlay

  Troubleshooting connections and Wi - Fi networks

  Recommended Wi - Fi settings

  WiFi Diagnostic Software (for Mac users)

  You will also find help on this page, where I have collected some of the more unusual solutions for network problems.

• Satellite A120: Microphone does not work when the power cable is unplugged

  I have a Toshiba Satellite Pro A120, which has just begun to play up...

  I regularly record music of my DJ Mixer in microphone of my laptop entry, recording in Adobe Audition.

  Because the power supply makes a buzzing sound, I can't register with the power cable plugged... If I always record with the unplugged power cable, running off battery.

  I've never had any problems before, but what has caused the problem, I now, was earlier the battery ran out while recording, put the laptop into hibernation mode.

  Since then, I can't register with the power cable disconnected. He recorded only with the cable - which is not a good cause snoring.

  It is not a problem with hearing, because in Windows Vista its implemented the problem proved too. As soon as I unplug the power cable, microphone disappears from view.

  I used to work in IT support, so I'm not a technophobe - but I can't for the life of me works why it would suddenly start to occur, power is not related to the entrance it is micro... !

  One of you lovely people have ideas? I checked power options and the Device Manager to see if theres no hardware issues, but there isn't.

  I also reinstalled my sound card drivers.

  It's strange. I guess you tried a boot cold fresh. Hibernation can sometimes cause problems with the devices.

  Try to update the BIOS.

  If all else fails, you may need to reinstall Windows. (Backup your data and run recovery by holding down the button reset during power on)

• Whenever I try to open the App Store it will remain open for more than 30 seconds before the close. Or it just restarts as soon as a home screen scroll above him. I can't keep it open long enough to even download an application.

  Whenever I try to open the App Store it will remain open for more than 30 seconds before the close. Or it just restarts as soon as a home screen scroll above him. I can't keep it open long enough to even download an application.

  Hello monorayfromportland,

  If you are unable to connect to the iTunes Store on your Apple TV, take a look at the troubleshooting steps below:

  If you cannot connect to the iTunes Store
  
  

  If you cannot connect to the iTunes Store on your Apple TV (4th generation):

  1. Make sure that your date and time are correct. Go to settings > general > Date and time.
  2. Check if your Apple TV software is up-to-date. To check the updates, select settings > system > software updates > software update.
  3. Make sure you have an active network connection. Go to settings > network.
  4. Check to see if other devices, such as computers or tablets, can connect to Wi - Fi and access to the Internet.
  5. Reset the wireless router by turning and then again.

  Take care.

• Why dllhost.exe crashes when trying to create thumbnails for video files 3D it was working before the update to Internet Explorer 10

  I could view and manipulate all my files video 3D before the update to IE10, so I did a restore and all is well again.

  The problem IE10 was installed host.dll/substitution/thumbnail cache com would consume memory until it saturated my whole system and crashing.

  Updated platform for Windows 7 x 64-Edition (KB2670838)

  http://support.Microsoft.com/kb/2670838?WA=wsignin1.0%2cwsignin1.0

  This update of the platform also allows the emergence of the problem.

  I could view and manipulate all my files video 3D before the update to IE10, so I did a restore and all is well again.

  The problem IE10 was installed host.dll/substitution/thumbnail cache com would consume memory until it saturated my whole system and crashing.

  Updated platform for Windows 7 x 64-Edition (KB2670838)

  http://support.Microsoft.com/kb/2670838?WA=wsignin1.0%2cwsignin1.0

  This update of the platform also allows the emergence of the problem.

  Why does dllhost.exe Com surrogate consumes memory until the crash.

  This happens when I highlight or view a folder containing video files, even if I close the file or select another folder, that maintains the memory consuming.

  It seems to happen more often with the 3D video files, but it has done the same with the 2D files.

  It therefore seems to be a problem with the windows thumb nails system on these files.

  Besides trying to delete or move the file or folder, while the Com Surrogate consumes memory Delete cannot complete the task.

  What I did is to find by selecting delete file in question, then go to Task Manager stopping Com Surrogate, then deletes the file.

  OK guys and girls, here is the scoop or what I discovered.

  Went to paid Support MS started a ticket gave them the info of the problem.

  I backed up before you have to pay, but it will still leave a ticket on the system req.

  Them I did a searck masive on this problem and ran into this and I beleve it's true. It's the way they handled a similar problem in Vista.

  So here it is.

  "MS are aware of the problems with certain chipset / combinations ofdriver with the updated KB2670838.
  They also have problems with the installation of IE10

  They work on these two issues and will be updated as and when they are convinced that they have solved the problems.
  In the meantime, the recommendation is that if the update isn't the first phase of installation, make sure that it is uninstalled and then hide it - Windows Update will display it when it is updated. »

  To uninstall IE10 and KB2670838 update, should be fixed hide automatic update when your pop back up to be updated the problem.

  Evidence that MS knows that IE10 has problems on some hardware platforms is here.

  http://TechNet.Microsoft.com/en-us/IE/jj898509.aspx

  Hope this helps Every One.

• After the power failure during the restoration of the previous day, cannot enter os or passed the password even in safe mode.

  Have laptop Dell 8100, recently used out of town on a wireless remote, installed updates 47 system.  Upon return home, tried to change cable modem I used before purchasing a desktop computer.  I could not the laptop to work on internet.  So I restored system he choose 2007 too far back, then tried to restore someday, when restoring back to the Sunday I was untangle cords and press the power switch on the surge protector.  Now, I can't even in the system.  Go to the login password that I've ever had, my son has changed in 2002 from Tower to the yankees and protected by to keep his friend out of it, but I've never had to use a password he would always automatically functioning screen icons until yesterday.  The second problem the remote while the screen flashed occasionally and would be less bright black with very low juror I would turn off and cool and could use it later.  It happened when he was 6 months old and they replaced the screen.  In the research I found it eventually the inverter is not the screen and found where to buy however, I can not connect to my system now.  I don't want a new laptop, it has been used very little has everything I need and more photos.  My son who has put a password in 2002 died.  I want to return to my laptop, replace and/or to the inverter.  Need to travel to work.  Unemployed and own building company.  How to remove password?  I've never used a password and don't want everything.  Want to right back to my machine.  When asking my password it says field is no longer round.  Don't know what that means.  I know that he renamed Yankee, I saw that when updating.

  The notion of 'Password' is to prevent any attempt to usurp the security it provides. If there is a quick and easy way to circumvent or to usurp the password protected system, then it would raise the question, what should a password?

  I'm afraid that if you've exhausted all the possibilities and are unable to find/recover your password, you will need to reformat the hard drive and reinstall the operating system.

  The Microsoft policy about lost or forgotten passwords .

• After the 27.0.1, I can access is no longer on a secure site. I now get error code: ssl_error_bad_mac_alert. It worked before the upgrade.

  I'm trying to access the administration page of GUI on my wireless controller. It's using a certificate issued by the vendor who makes it, so the names do not match. I created a permanent exception for the certificate. Whenever I try to access the site, I now get the following error every time:

  The secure connection failed

  An error occurred during a connection to 172.24.6.10:4343. Peer SSL reports incorrect Message Authentication Code. (Error code: ssl_error_bad_mac_alert)

     The page you are trying to view cannot be shown because the authenticity of the received data could not be verified.
     Please contact the website owners to inform them of this problem. Alternatively, use the command found in the help menu to report this broken site.
  

  This page worked fine before the most recent update.

  Y at - it a setting or something I can change to allow this page to load?

  I saw reported problems caused by Firefox with the help of a few specific cipher suites that are not properly supported by the server.

  A possibility to test this is to disable all the SSL cipher suites on the topic: config page (i.e. switches security.ssl3. * prefs that are true to false) and allow both to see if you can find the culprit and continue this suite disabled and reset others or continue its tests to see work encryption algorithms.
  
  Do a hard refresh the tab with the page of 172.24.6.10:4343 via Ctrl + F5 after each change.

  You can open the topic: config page via the address bar.

  • http://KB.mozillazine.org/about:config

• Satellite C660 - 115 WLan connection only works when the power cable is connected

  Hello

  A few weeks ago, I bought a Satellite C660-115. I want to surf the internet anywhere in my house without any son/cables.
  On the first day, I had this problem: when I disconnect _power_ cable, the wireless connection will stop working.

  The Web page on my screen will always be there, but a new page loading is a problem.
  It is sometimes useful to recharge (by pressing F5), - sometimes not. It is always useful to "ip address of repair", but not for long.

  The only solution is to atach regardless of how much power the battery has still the power cord.
  When I do, it is no problem whith the connection at all.
  I went back to the store where I bought it, they related to their own wireless network and they have had the same problem after a few minutes. In the shop too attach the power cable solved the problem.

  So the problem must be in my lap top, not in my network (modem or almost).

  Doesn't this all seem familiar, and if so, how can I solve this?

  I hope that my English is understandable, I live in Holland.
  Thanks in advance!

  Here is the solution:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=59177

  Change options for saving for the Wlan in Windows 7 power management

• bluetooth mobile keyboard wedge does not work before the beginning of the window

  Hello Microsoft,

  I bought the mobile bluetooth keyboard dock recently.
  It works not in the BIOS and CMOS to move but to start the window, everything is ok.
  I use dougle bluetooth to connect this with my computer keyboard.
  I already activated the USB keyboard in the CMOS using old PS2 Keyboard. But it does not work.
  Please help me to use my keyboard before the beginning of the window.
  Respect,
  Arkar

  Hello

  Which machine or laptop you are using.,.
  some of the model require Bluetooth patch file to complete, that patch file will be given by the laptop or desktop vendor, please contact their tech support toll free number.check with Bluetooth mouse also

• I want to disable the ability to go back and save your work before the expiration of time on the family safety settings

  My daughter uses the option to go back and save your work before closing down as a way open to passing the family safety settings. When she is about to be disconnected because of the time limit, she knows that three programs open with live data on them (like playing content in YouTube, chatting and playing an internet game all at the same time) he will come to the top and he the opportunity to go back and close its data. It completely negates the purpose of the limits of time. Because it doesn't then go back to the top and stop her. It falls just the problem completely. I don't know that this is just a gap in the family of security software. But thought I would ask to see if this option can be disabled, or if there is a way around it.

  If you find the Parental control in Windows help, he will guide you to articles online for the safety of these two parental controls & family.  There may be a solution in the event of children in one of these roads.

• I have a Pavilion Elite M9150F and it seems that the ignition button does not work. The power light is on

  My Pavilion Elite M9150F P/N KC880AA-ABA running Windows Vista Home Premium 32 bit. The device turns on no switch or remote control. He lite is turned on and power is running through the unit until button (checked through AC voltage detector) are there known issues with these? Are there spare parts? It doesn't hang or move the last time it was turned on. What are my options? Thanks for any help.

  Hello cello6996
  
  You are in warranty? If so, I would suggest contacting HP. If you are out of warranty, follow the steps below.
  
  How does a power button is essentially that it shorts two special pins. This short film is a signal to the power on the power supply and all components. A quick Google search reveals the most common method to do this is to disconnect the wires to the pins on the motherboard power button and then tap a screwdriver against just these two pins. Use gloves as a precaution. or a screwdriver with an insulated handle.
  How to bypass the power on button on pc
  Is there a way to bypass the power switch?
  
  If the computer starts correctly something wrong with the power button. If the problem persists, it is more than likely a problem with one of the hardware components and the problem will have to be isolated further. Let me know what happens.

• I had a power failure that created a restart of windows vista problem

  I had a power failure that created windows error and cannot start my lap top. I understand that I must save the files & photos before trying to reload Vista in its original configuration... How do I go about backing up since the computer does not load...? How much does it cost if I'm looking for a specialist to backup?

  Hello

  power outages are often the cause of hardware problems

  You can try these methods to save the data

  1 slave the drive in another computer and try to read the data in this way

  2 buy or borrow a pregnant USB hard drive upgrade disk hard inside plug it into another computer and try to read the data in this way

  3. If your equipment is damaged by using Knoppix or similar CD linux to retrieve data won't work because they depend on your working materials

  Read about it, even if it's here

  http://www.Knopper.NET/Knoppix/index-en.html

  4 data recovery experts are very expensive

  You can always do a startup repair disk and try to start windows

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

• Graphics ATI DV7 - 4087CL Pavilion does not work on the games! and on windows. Only Intel HD

  Hello everyone, I have the problem on my laptop (Pavilion DV7-4087CL_. I have windows 7 64 bit and all drivers are updated and special ATI AMD Radeon LAST. After installation too, I can't play 3d games or whatever the game with my ati.

  DXdiags also said INTEL HD not ati amd...

  What solution have with this and how im taking all the power of the laptop because is very slow with intel

  Concerning

  Arkadios

  Hi @arkas

  Welcome to the HP Forums! I see you're a few graphic problems. Did you install the ATI driver on the AMD website? If so, that's the problem. You have switchable graphics, which means that you have two video cards. The Intel card is designed for your treatment of basic graphics every day while the ATI card is designed to handle most of the work. Switchable graphics drivers are configured by the manufacturer of the laptop not the manufacturer of the graphics card.

  I suggest that you install your AMD HD graphics driver and your high-definition Intel Graphics Driver. If you need more information on the switchable graphics this document HP Switchable Graphics on laptops equipped with Intel and ATI GPU.

• Vista will not work after the power to

  I have a HP Pavilion laptop with Vista SP 1 64-bit installed.  Tuesday, April 14 I turned it on only to freeze with in ten minutes after having informed me it had installed updates.  At first, I thought it was a problem with my browser and uninstalled FireFox.  This does not alleviate the problem.  I run my adware and spyware detectors to see if something to eat to the top of the RAM.  All scans were free of malware and it is free of all viruses as well.  It took me three tries to get even the scans indeed the computer would lock up after 10-15 minutes whenever I turn it on.  I thought maybe it was overheating and checked, but the CPU temperature is normal and the fan runs.  I tried a system restore to get rid the updates in case this was the cause of the problem since it had fixed the errors before.  No luck. On the first two tests, he wouldn't even finish the restoration of the system.  I ran the memory controller and it froze and then shut down the computer.
  It crashed last night, while I was running a System File Checker and everytime I try to start it in safe mode, it gets stuck on:
  Support: \Windows\system32\drivers\crcdisk.sys
  After sitting there for sometimes more than ten minutes, it starts as usual only to freeze up again.  I tried to boot into safe mode with network and just Safemode and he refuses to do.  I am very worried that I have a big problem, but I can't stay up long enough to do any in-depth audit.
  All the world had similar problems or might know what the issue could be or am I just screwed?

  Hello brohne,

  Please use the Microsoft Answers form. Because you can run the sfc command or get no results to start in safe mode, I recommend that you perform a repair installation.  This option allows you to repair you computer and all in keeping your documents.  PLEASE SAVE YOUR SYSTEM VISTA FIRST.  The link below explains how to perform a repair installation.

  http://social.answers.Microsoft.com/forums/en-us/VistaInstall/thread/58ed3b94-D603-4FEC-83CA-b3d15d1275b8/
  Thank you for using answers Forum. Please let us know how it works.

  Joseph
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Satellite A200: Should I remove the battery when working on the power supply

  Hello

  I've been running an A200 machine for the last 2 months, bought as a desktop replacement in order to fit in my small apartment. I realize now that I never ued work on battery - it is always powered on sector. Since this is unlikely to change, should I remove the battery? Deing battery degrades remaining in the machine while it is continusouly by the industry feeding, or does it not matter?

  Thank you very much in advance for your reviews.

  GW.

  You can remove it, but it should not be done. For me, it's stupid to remove the battery and let the dust make the battery place dirty. The batteries we use today are very good and Scott wrote the electronic power supply just to check if the battery is full and care the battery and the battery capacity.