Publish the pix 501 Web server

Remote office is connected to Headquarters via the site to site vpn. I have 1 static IP address (on the remote site) that I use for the site to site. I need to publish a web server at the remote site.

My question is if I can use the same IP address for VPN and web server edition, I have a problem for the web server to publish

See attachment

Thanks for your time

Hello

Of course, you can use the same public IP address of your external interface for port forwarding, you just need to apply the acl to your external interface

Add the line below to the config file. NT and try www

Access-group interface incoming outside

If no joy you can try to modify the acl to reflect outside keyword instead of the public IP address

example:

list of allowed inbound tcp access any interface outside eq www

and delete the old (no list of access allowed tcp not incoming of any host 74.94.2yy.xxx eq www)

Concerning

Tags: Cisco Security

Similar Questions

  • default configuration of the pix 501 past recovery/restoration

    You need to reset the PIX 501 (lost password). I tried the password recovery instructions and accesses the monitor command by using the connection of the console, but cannot get the file to be transferred using tftp (ping command also expires).

    1. in case ordering interface be set to 0 or 1 (I used 1)

    2. the order of the address I was using 192.168.1.1

    3. order the server, I was using the IP address of the tftp server

    4. entry door? (Which is the PIX or the computer)?

    5. in addition to the blue console cable that if all other cables should be connected and which ports.

    Thank you

    I'm guessing you already have this document:

    http://www.Cisco.com/en/us/customer/products/HW/vpndevc/ps2030/products_password_recovery09186a008009478b.shtml

    I would like to use the default value inside of the interface of the 1. Connect a standard ethernet cable to one of the Interior ports on the PIX and the other to your PC that has the server tftp on it of the interface software. Make sure that you see a link on both ends light. If not, take this cable or save it if you think it is a crossover cable. If you set the PIX address to: 192.168.1.1, then I would set my tftp server address: 192.168.1.2 or something in the same subnet. In this way we will not care what is the gateway address. No need to let pesky routers get in the way, when we're down!

    Since you asked the question 5 above, I'll explain. You should have a console cable connected, it seems do you since you can get to the monitor > prompt. You'll also need an ethernet cable plugged in a PC running a server tftp with the IP address: 192.168.1.2 3Com made a server tftp really good F * R * E * E.

    http://support.3Com.com/software/utilities_for_windows_32_bit.htm

    Select the last file in the list. Make sure you get that file recovery of password for the Cisco link above for the PIX OS version you are running. Configure the tftp server to point to the directory containing the PIX password recovery file and you are ready. Good luck, Derrick

  • 4 Apex-Apex 3.2 on the same Oracle web server running

    Is it possible to run Apex 3.2 and 4 Apex on the same Oracle web server (apache)? We have two instances of different database with Apex 3.2 and 4 installed and configured oracle mod_plsql with web server.

    There are separate aliases defined in dads.conf as

    Alias is "/ opt/oracle/11 GR 2/apex/images / '-> apex 3.2
    Alias /i4/ "/ opt/oracle/11 GR 2/apex/images4 / «-> apex 4»»

    Apex 4 isn't picking up directory of images on the right, and it is not possible to log on to administer the apex workspace. Is it possible to set this up?

    Published by: user12099969 on June 28, 2010 05:43

    You have run the installation script with the appropriate letter for each alias directory instances?

    You have bounced the http?

    concerning

  • HP Laserjet M606x: Disable the option 'Print' in the built-in Web server

    I am testing a new HP Laserjet M606 device and to disable the option 'Print' which is displayed in the 'Information' tab in the built-in webserver (EWS). I have a firewall turned on, turned off wireless printing, FTP, AirPrint, Web Services, PPI and independent producers is also disabled. HP Jetdirect XML service is also disabled. I have crossed most of the EWS settings and configuration options in JetAdmin and did not find an option to turn this feature off.

    The device will be located in a public place and will have a reserved/static IP address (DHCP reserved). We charge for services to the end-users of printing - having this option turned on means that users can print for free if they find the IP address of the printer - not an ideal situation.

    Is it possible to disable this option permanently? The only other solution is to disable EWS entirely, if possible.

    To be a little more specific in the built-in web server click the Security tab. Now scroll down until you find the section for embedded web server settings. I was watching who had enough current firmware in the machine there is a checkbox to enable or disable the option for printing on the information page.

  • Cisco 3640 to the PIX 501 site 2 site VPN performance specifications.

    I intend on creating a site-2-site VPN in Star configuration with a Cisco 3640 as the hub and PIX 501 at the remote sites. My question is around the plug that I read.

    .

    The specifications for a PIX-501-BUN-K9 tell PIX 501 3DES Bundle (chassis, SW, 10 users, 3DES).

    .

    A question is what really "10 users. Which is the limit of the number of concurrent sessions, I have on the VPN at a given time, or that it means something else?

    .

    I also read the specs say that the Maximum number of VPN tunnels that can support a PIX 501 is 5. Because I'm not going to make a tunnel between the PIX 501 at the remote site and the 3640 on the central site, I think I would be OK. Is that correct or is the max value talk the maximum number of concurrent sessions on the tunnel tunnels?

    .

    Thank you.

    UDP traffic always creates a session in the PIX so that the return traffic will be allowed in. The UDP timeout is 2 minutes but IIRC. If you go around NAT with a statement of "nat 0" should not create an xlate I think.

    The real time is hard to say really, probably around 2 minutes for a UDP-only user, you would probably make a few 'local sho' orders on the PIX to really see for sure however.

  • Help the PIX 501 - cannot access startup.html

    I'm new to the network and has received a job to configure the PIX 501 firewall.

    The fact is:

    We use IP table rules as a firewall on a linux machine. My pc is connected to a switch. So I use the yellow network cable to connect the port of the Pix 501 0 to the port in the switch. Then I disconnect my pc of swich cable and plug into the port of the Pix 501 1.

    My pc is to use a static ip address before. I try to change to automatically get an IP address, but it will not work. So I changed the setting and use the IP address originally. Pop up message network connection icon says that the local connection is enabled. But when I try to ping 192.168.1.1, request time-out. Also I can't acess the https://192.168.1.1/startup.html.

    I have a look at Books Online cisco and shootings of disorder, but most of them talk about the configuration or more advance features. I'm still on the very basic level to try to connect to the firewall.

    I hope someone can help me. All ideas and questions are welcome. Thank you.

    Your IP address should be fine. You do not want to have the PIX connected to your local network, even if you have the Linux firewall as well as this will cause a conflict. Keep the PIX the LAN for now. Your DNS configuration will have no effect because the url you are trying to reach is based on the IP address and not the domain name if your PC has nothing to look for.

    You have to check the cable that you use - if your PIX has only an 'inside' interface, then you must use a crossover cable. If he has four so it's built in switch for a straight cable will be fine. Is what PIX model?

    After checking the cable - see if you can console in the firewall - use the blue cable that came with the PIX and set up a connection (hyper terminal) terminal with the help of 9600, 8, no 1. If you can console and then you can stick in a basic configuration you can get.

  • CF2016 - Alias/cf_scripts / scripts on the built-in Web server

    I am following the guide lockdown here:

    http://wwwimages.Adobe.com/content/dam/ACOM/en/products/ColdFusion/PDFs/ColdFusion-2016-Lo ckdown - guide.pdf

    The guide proposes to move/cf_scripts/scripts directory, I did.

    The guide also offers using only the web server integrated access to the ColdFusion administrator, this is how I put it in place.

    The guide also indicates that you need to create an alias for the directory moved to the built-in web server.  See page 58 of the PDF.

    If you plan to use the built-in web server to access the ColdFusion administrator, you may need to create an alias for/cf_scripts/scripts if you have changed the default Script Src in ColdFusion administrator.

    To create a new Alias for/cf_scripts/scripts on the built-in web server

    If you plan to use the web server to access the ColdFusion administrator, then you must also add an alias by adding a tag context inside the tag of the located server.xml file host: /opt/cf11/cfusion/runtime/conf/server.xml

    < context path = ' / '.

    docBase = "/ opt/cf11/cfusion/wwwroot".

    Workie = "/ opt/cf11/fusion/runtime/cone/Catalina/localhost/tamp.

    alias = "/ coscripts = / opt/cf11/fusion/wwwroot/CFIDE/scripts" / >

    Restart ColdFusion, and then test by visiting /cfscripts/cfform.js on your server of builtin.

    There are a ton of typos in the present (Workie vs WorDir, vs conf cone, Pack vs coscripts vs cfscripts, tmp, etc..

    This also seems to be referencing the paths cf11 (CFIDE/scripts vs /cfscripts/cfform.js vs cf_scripts/scripts/cfform.js and cf_scripts/scripts).

    In addition, coldfusion - error.log notes the following:

    WARNING: A context path should be an empty string or start with a ' / ' and do not end with a ' / '. [The path [/] does not satisfy these criteria and has been replaced by]

    WARNING: [SetPropertiesRule] {Server/Service/engine/host/context} setting property 'alias' to ' / cf_scripts/scripts = / cf_scripts/test_scripts "did not find a corresponding property.

    The first line is not a problem, but the second line is.  alias is not a valid property of the context.

    The server.xml file is an example, and it is as follows:

    "< context path =" "docBase =" < cf_home > / wwwroot "WorkDir =" "< cf_home > / runtime/conf/Catalina/localhost/tmp" > "

    < resources >

    < base preResources = "docBase1" className = "org.apache.catalina.webresources.DirResourceSet" webAppMount ="/ aliasPath1" / > "

    < base preResources = "docBase2" className = "org.apache.catalina.webresources.DirResourceSet" webAppMount ="/ aliasPath2" / > "

    < / resource >

    < / context >

    It aligns with the Apache docs.

    I have CF installed on Windows, to F:\CF_2016\.  That's what I did to alias the directory of scripts (renamed to test_scripts for testing) for the built-in web server:

    < context path = "/" docBase = "F:/CF_2016/cfusion/wwwroot" WorkDir = "F:/CF_2016/cfusion/runtime/conf/Catalina/localhost/tmp" >

    < resources >

    < base preResources = className "F:/CF_2016/cfusion/wwwroot/cf_scripts/test_scripts" = "org.apache.catalina.webresources.DirResourceSet" webAppMount = "/ cf_scripts/scripts" / > "

    < / resource >

    < / context >

    It seems to work.  Is this correct? Wouldn't be an alias as \Scripts or /cfscripts instead of/cf_scripts/scripts?

    Why exactly should I alias this to the administrator?

    Thank you

    Hello

    I was in the same boat (we are defining a profile secure for testing) and I see no one answered you so I want to offer what we were doing.

    webAppMount = "/ {NEW_CFSCRIPTS_VIRTUAL_DIRTORYNAME" / >} "

    You see, I believe the problem you had previously was that the base should be the physical directory and the webAppMount should be the virtual directory.

    You were correct about the typos in the "official" document

    I don't know if it's important or not, but we have also created the directory "tmp" (quoted above) within the "{YOUR_DRIVE} :/. "{CFROOT} / cfusion/runtime/conf/Catalina/localhost / ' because it is not there by default.

    Kind regards
    David

  • How not one disables the built-in web server?

    In my case Adobe technology enabled web server integrated for some sort of test and left, that it has.  I would like once more to turn it off to limit the attack surface that I see it's getting some visits by an internal network vulnerability scanner.

    Where is the configuration file and setting specific to only disable the built-in web server?

    Unwanted changes to the built-in web server is referenced in this article in the forum: http://forums.Adobe.com/message/4388179

    Add Miguel-F information, in case you use ColdFusion 9 then, adding only the code below, in the section above will be used.

    true

  • Where to put XSD in the local (HTTP) Web server, so that they are visible?

    Currently I'm statically import my HDD XSD schema files into projects.

    However, I prefer to put these XSD files on the local (HTTP) Web server, so that I can return to their
    dynamically with a http://... address.

    How (where / which directory) what I have to put files to XSD schema on the Oracle Server local so that I can call them http://127.0.0.1/ resp. http://localhost/...

    Peter

    It is also common to the XSD files in $ORACLE_HOME/bpel/system/xmllib

    They are then available as http://HOST: PORT/orabpel/xmllib/XYZ.xsd.

    I recommend you do your own file in this directory. These are served by OC4J upward, not purely by Apache however.

  • My animate file seems to work very well locally, but the images are not connected properly when I publish and publish them to a web server.

    I have an HTML5 animation I'm working. When I saw it locally, it seems to work fine, but when I publish and display on our web server, it doesn't seem to be able to find the images. The images are all in the pictures folder and everything seems to point to the right place, but it is not appear correctly on the web server.

    If someone saw, I would be very happy.

    I have it! Apparently, it's the spaces in the URL (which are presented as 20%). When the file is moved/renamed, it worked fine.

  • Configure the PIX 501 for IDS

    I have a PIX 501 with wired high-speed LAN headquarters inside and outside. Which would be a solid policy IDS to enable and what interfaces it must be applied to? There will be other measures necessary to enable IDS?

    IDS on the PIX itself is very limited, it checks only 59 signatures listed here (http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_62/cmdref/gl.htm#xtocid9 under the section of signatures supported IDS). The signatures themselves are pretty basic.

    If you do not want to activate this, then for the signatures of attacks I would fix for drop/alarm/reset action, which is the default anyway.

    You will also need to set the logging to a syslog server and monitoring for any 4000nn messages in syslog, cause it event IDS.

  • Photosmart 2575 AIO - need to reset the password for the built-in web server

    People,

    I lost the password to the web server integrated on my HP Photosmart 2575 all-in-one.

    Can you please help me reset it?

    Thanks in advance and Bravo!

    Cristian.

    csantiago78 wrote:

    I lost the password to the web server integrated on my HP Photosmart 2575 all-in-one.

    Can you please help me reset it?

    This thread gives to think that a full reset can be done by disconnecting the power to the Photosmart 2575, then plug the power while pressing the keys 'Cancel' and 'OK '.

  • Finding information on the ink using the built-in Web server in Photosmarts

    SAP (built-in web server) is a useful tool which is used in many respects related to networking, it can provide information on Web Services and can also set Static IP and static DNS on the printer.

    But, if it is connected to the network via Ethernet or via a wireless connection with the Officejet, it is also a great way to check the ink levels and number of pages.

    To access EWS of the printer.  Take the IP address of the printer and type it in a browser on the computer. The IP address can be found under settings wireless to the printer on display or on the Network Configuration report that can be printed.

    Once we've hit this address in the browser, the integrated Web server opens to a screen that will show you some basic information on this page. It will be showing the ink levels estimated for the printer.

    For a more detailed look at the output of consumer and media of ink printers:

    1. once on the homepage of the Photosmart EWS, click the tab above titled "Tools".

    2. from there, looking at the left column on the new page that appears, click reports

    3. from here, click use report

     

    • We'll now be able to see how many cartridges have been replaced for each color in the printer.
    • Once can see the total number of pages for pages printed by the printer
    • This report will also give a break down on how many pages when printed on plain paper, photos and media size

    So, for those who are connected by Ethernet or wireless to the printer; Here's another option to find information about the ink levels.  These steps and information listed are general guidelines.

     

    I hope the community finds this is useful and informative.  Good impression!

  • The import of the PIX 501 config to ASA 5505

    Is there something special that must occur to import a PIX 501 (IOS Version 6.3) config to an ASA 5505 appliance or is it as simple as download the config?

    Greg

    No, this isn't unfortunately because your pix is running 6.4 and the ASA 5505 will run a minimum of code 7.x and there were quite a few changes. Note that many existing commands would work, but some will not. Attached is a link to a doc for improving pix ASA who speaks both a manual method and an assisted version of tool -.

    http://www.Cisco.com/en/us/docs/security/ASA/migration/guide/pix2asa.html

    Jon

  • Problems with PIX 501 and Server MS Cert

    Hi all

    I have two problems with my PIX 501:

    1. registration works well. The pix has a certificate and use it with SSL and VPN connections. But after a refill, the pix certificate is lost and it has regenerated again self-signed certificate!

    Yes, I wrote mem and ca records all!

    2. at the request of ca CRL , I get the following debugging:

    Crypto CA thread wakes!

    CRYPTO_PKI: Cannot be named County ava

    CRYPTO_PKI: transaction GetCRL completed

    Crypto CA thread sleeps!

    CI thread wakes!

    And the CRL is empty.

    Does anyone have any idea?

    Bert Koelewijn

    Not sure about 1, but 2 is usually caused by the COP (Point of Distribution of CRL, basically the situation where the PIX can download the Revocation list from) listed in cert CA is in a format the PIX does not, generally an LDAP URL.

    Check the following prayer:

    Open the administration tool of CA (Certification Authority) then

    (1) right click on the name of CA and choose 'properties '.

    2) click on the tab "Policy Module".

    3) click on the button "configure."

    4) click on the tab "X.509 extensions".

    > From there, it can display the list of the "CRL Distribution Points".

    Turn off everything that isn't HTTP.

    You need to reinstall the CERT in the PIX, I think, but then it should be able to download the CRL through HTTP instead of LDAP.

Maybe you are looking for