Published the network Variables not accessible by other computers on the network

Similar Questions

• Windows 7 does not connect to other computers in the same homegroup network

  Computer is a Dell Latitude E6500 in good working condition. Printer is connected to a desktop computer running on Pentium IV with HP LasetJet 2100.  The Pentium IV is only for printing but must be able to make a link to it. All systems have max ram and large capacity disks. All systems are running Windows 7.

  Hello Willard,

  Thanks for posting your question on the Microsoft community.

  I would like to know some information about the problem so that we can help you better.

  1. what happens when you try to connect to other computers? you receive an error message or code?
  2 update you installed before the show?

  Thank you to provide detailed information on the issue and your efforts to resolve.

  This problem can occur for the following reasons:

  -Network discovery may be turned off.
  -Password-protected sharing is turned on.

  I would suggest trying the following methods and check if it helps.

  Method 1:
  Run the network troubleshooting and check.
  Reference:
  Using the troubleshooter from network in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  If this does not help, use method 2.

  Method 2:
  Please use the suggestions contained in this Microsoft support article and check the issue.
  Reference:
  Why can't I connect to other computers?
  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-other-computers

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• vmware site is not accessible from other hosts

  The host is Windows 7, and the guest is CentOS. I managed to put in

  openSSH and apache on the rise and the site is visible to the host, but I can't

  access it from outside my LAN (I have a router) or inside my local network (since one

  another computer of course). How to configure Vmware & window7 then I have

  can access my virtual server on the internet?

  If you did what I said in my reply to you the other day this subject, you should be able to access by other computers on your local network, but not in itself for WAN connections and you will need to set up your router correctly to enable connectivity on the Internet virtual computer.

  You did as I suggested and read Chapter 14 you have a knowledge of virtual networks and then bridged Network Adapter to the virtual machine value and disable auto fill in the virtual network Editor?

  If this is not the case, go back and read: Re: vmware is accessible from the host machine, but not on other computers

  BTW, in the future do not start a second thread for discussion of the matter.

• Homepage not accessible from remote computers

  Hello
  I just installed version 10g 2 x, but I am not able to access XE home page of other computers on my network even though I configured XE that this is possible.
  
  I'm under Oracle_Server_Linux 5,6.
  I accepted all the default values during the installation of XE.
  Using Firefox, I've traveled to http://127.0.0.1:8080 / apex
  
  Then I sailed in the homepage of/home/administration/Manage_HTTP_Access
  and selected "access: Available_from_local_server_and_remote_clients.
  and then you click on Apply_Changes, which seemed to complete successfully.
  
  The help of the host on which the XE is installed, I am able to use Firefox to access http://192.168.0.102:8080 / apex from which I expected to find, and that works fine. But when I try this from a remote computer, the connection fails.
  
  I'm sure the network itself works because ping and ssh work between computers.
  
  Someone has ideas on how diagnose and fix this probem?
  
  Thanks, Tcharles.

  When he works to the host, but not remotely, a likely culprit is your firewall.

  The port of the Apex and the database listening port, if you also want the remote database connections, must be added to your firewall exceptions list.

  A quick check to see if the port is blocked, try a telnet to the host and port.

  $ telnet 192.168.0.2 8080
  ...
  $ telnet 192.168.0.2 1521
  ...
  

  And to be sure that the correct port is in use, check with a "lsnrctl status", you should see an entry for endpoint listens for http and ip address and port number as well.

• Win7 computer cannot connect to other computers Win7 network "\\computername is not accessible. You might not have permission to use this network resource ".

  I have a Windows 7 (box A) system that cannot connect to files shared on another computer in Windows 7 (box B).

  • On the 'network card' and 'See the network computers and devices', I can see box B of area A.
  • I can ping Box B of area A.
  • I can connect on MEDIA sharing on box B of area A.
  • Area C (another system of Windows 7) I can connect to the B area and am presented with a box of authentication to connect to the shares (i.e., box B works as it should).

  But the box has double clicking on box B or using \\computername or \\IP_Address the dialog box run, I get the error:

  ----

  \\computername is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions.

  The network is not present or not started.

  ----

  I know that the system is available, because the area C can access... But something's not on the box... It cannot connect to zone B or C. Box

  I have disabled the firewall on both systems without result.

  I reinstalled the network adapter and Client for Microsoft Networks is installed on the box.

  Yet somehow box's not connection to other computers on the network.

  Any thoughts on what I should check would be appreciated.  Thanks in advance for the help.

  OK... so I was able to track down and get it fixed...

  I found another symptom (that would be a good way to check and see if you experience the same problem).

  In the network and sharing Center, I clicked on "Change advanced sharing settings" in the left column. I found that the radio button under "File and printer sharing" was put on the OFF position.  I started and saved the changes, but when I returned in these settings, it is once again in the off position.

  It turned out that the workstation service is set to disabled (which also caused the computer browser service for not being able to boot). I activated the workstation service, started, and set it to automatic.  Then did the same for the computer browser service.

  Both of these services running, the "File and printer sharing" it will remain actually on IT, and I am able to connect to other devices on the network in the way I had to.

  I can't mark this message as the solution (perhaps because I posted it?) so if someone he will quote as their response to the post office, I'll be able to mark as answer.

• Can I use the timestamp to a global variable that is published to network to reduce network traffic?

  I would use a couple of network-has published the global variables that will contain large groups of data.  I want to host them on a device, but read them in several - consider a distributed control system.  The data will be updated very rarely, but when that happens, I want that all my GUI to know quickly.  I have all the GUI, simply read data 4 x per second (which would be fast enough), but I was wondering if there is a more elegant solution (always using global variables).  If I read only the timestamp 4 x per second each of the HMI, compare to the last reading and then interrogate the integer variable if timestamps are different, which will require fewer resources that just enter the integer variable each time?  In other words, the read timestamp uses the same amount of resources as the reading of the entire variable?

  With really simple code, assuming that the cluster "Data" is big enough, made...

  .. .get me no benefit on...

  mark3545 wrote:

  Which means that they are already doing what I want anyway, no?  If the reader is updated when it changes the writer, I can survey as often I want without increased traffic, correct?

  That is right.

• Do not see the other computers on the network of LabVIEW

  I have 2 computers on a network (cpu1 and cpu2) that I use for data collection, and then several computers that I don't use. I got it when I did an in LabVIEW shared variable, a "network has released" a. Once these variables are deployed on cpu1, I go to cpu2 change the shared variable in an another VI by allowing the aliasing and by accessing the address of the PSP. For some reason, I don't see all cpu1, but I can see the rest of the network.

  When I return to cpu1 and try to access an address PSP, I can see cpu1 and variables deployed, but I can't see cpu2 on the network (although I see that all of the other computers). I know that they can see themselves, I ping one of the IP addresses of the other and he delay 0ms. If you have suggestions for what to try, I'm for it! Thank you!

  Greg

  After have the right ports open and unlock the right programs, windows firewall does not prevent my shared variables!

• \\N-PC is not accessible. You might not have permission to use this network resource while trying to access the network computer

  Title: Cannot access computers on my network?

  For some reason any my computer won't let me access any computer on my network.

  When I try to open any computer, including mine, since the tab "network" on the left he gives an error message saying "\\N-PC is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. The specified network provider name is invalid.
  I ran the corner store to home group and network troubleshooting & two is out clearly said there are no problem.
  Anyone know how to fix this?

  Hello

  -What are the versions of the operating system installed on the conencted to computers in the network?

  -Did you do changes on the computer before this problem?

  Step 1: I suggest you to choose a network location, and then try to access the computer and check if it helps.

  Choose a network location

  http://Windows.Microsoft.com/en-us/Windows7/choosing-a-network-location

  Step 2: I also suggest you to check the network troubleshooter event logs to solve network problems and to check if it helps.

  Use Network Troubleshooter event logs to solve network problems

  http://Windows.Microsoft.com/en-us/Windows7/use-Network-Troubleshooter-event-logs-to-solve-network-problems

  Step 3: If the problem persists, I suggest you to follow the steps from the link and check if the problem persists.

  Why can't I connect to other computers?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-other-computers

  For reference:

  Networking of computers running different versions of Windows

  http://Windows.Microsoft.com/en-us/Windows7/networking-home-computers-running-different-versions-of-Windows

  Step 4: Disable the Antivirus

  I suggest to disable the Antivirus/Firewall temporarily, then check the issue.
  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-Firewall-on-or-off

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.
  Note: Please make sure that you enable the antivirus software after the test to keep your computer protected.

  Note: Turning off Windows Firewall may make your computer (and your network, if you have one) more vulnerable to damage caused by worms or hackers.

  Hope this information helps.

• FOJ 8500 909 g will not fully install, not accessible from the computers in home wireless network

  I bought an Officejet Pro 8500 909 g which worked well on our home network for 18 months.  Desktop is 32-bit Windows 7 with a USB cable.  Two wireless devices are 64-bit Windows 7.  Printer suddenly has not recognized the cartridges and frozen with the message "problem with the ink cartridge.  Called HP (unassisted) and tech support of holders of the contract of service - without help.  They sent a refurbished (even) model which I can't install on USB or wireless connection completely.  Yesterday, I was able to print at least one 3 machines on the network (not every machine wireless).  Today, I can not print even the USB device.  5 days lost uninstall then reinstall the printer software, router, etc.  Connected wireless network.  Printer says it is on the wireless network.  HP Solution center is not accessible because the "printer is not completely installed. Help?

  Hi EWQuince,

  The information you have given it seems that the printer is not on the same network as the computer. If the printer was on the same network as the computer, the IP address would be 192.168.1 instead of 192.168.33. You must run the printer Wireless Setup Wizard and make sure that you connect it to a network, the computers are connected. Once you have the printer connected to the same network all your problems should be solved.

  To connect to the wireless network

   

• "[------\\[Computer name] [name of the file or folder] is not accessible." You might not have permission to use this network resource.

  I have a home network with four computers. I have some folders and files we want to share. I haveselected these folders and files in each computer and right click top of opening and then the sharing and Security tab and check share this folder on the network, and then clicking apply and OK. [However, when I try to access these files or folders from another computer on the network I get the name of \\[Computer]------[file or folder name] is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permisions. Not enough server storage is available to process this command. Increased the value of the IRPStackSize following another Microsoft kb but stil get the same message.

  How can I fix this problem so that we can share these files and folders between my wife, children and myself.

  OS Win XP Pro SP3 with all its current updates on all computers.

  Any help and asisitance will be greatly appreciated

  Sadnewbie

  Hello

  Perform the steps from the link below and see if it helps.

  Error message when you try to access a network Windows XP computer: "you might not have permission to use this network resource".

  Important:  This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/)

  Hope this information helps.

• I:\ is not accessible .__Incorrect function___and in the other CD as__Blank that allowing open, DVD RAM, changing to CD player by inserting a correct DVD.

  System configuration: Windows XP with SP3 (Original) and all other Microsoft updates. An engraver of DVD from LG (HL - DT - ST DVDRAM) - SATA & Samsung DVD writer (TSSTcorp CDDVDW SH-S222A SCSI) - PATA later do IE August 2010 & September 2010 with the latest firmware, Nero 8.

  On a previously written DVD Insert, complete correct IE fully functional in other dvd burners / rom, DVD RAM icon changes to CD with two blank CD showing player one and not accessible with the message above in the other happening too the DVD-RAM to CD drive.

  Not understand, reported the problem to the company service centers assuming failed drive to be replaced during the warranty period. Provided with other drives of different model but unfortunately same case again. Searched the Internet, consulted and I have tried all sorts of remedies, but without success. Although all CDs, written or purchased fully functional, only previously written DVD.

  Then tried the solution of Microsoft Solution Center as "Mats_Run.dvd". Same here as that 'Please insert media readable by the CD/DVD drive [I:].  Windows tried to open the CD/DVD drive for you. "and finally as ' media in the CD / DVD drive is not readable (TSSTcorp CDDVDW SH - S222A SCSI CdRom Device' with the status"not set".)

  Wasted a lot of money and time behind this problem try this this, but without success. So looking forward to you for that my major problem not identified as an emergency like with me for needing to use these data. Again, no problem at all on my side of the machine and quality DVD that are required to access. And kindly, as soon as possible. Thank you.

  Lately, just after the announcement of this problem, insert a blank DVD to check DVD writing. And yet even ONCE - DVD RAM changing to CD player in both and in the above statement PATA and SATA a blank CD. Sense DVD is not reading as well as writing. Please add this also.

  Hi Sreeparno Baksi,

  Try the methods below:

  Method 1:

  Uninstall Nero 8 on your computer. You can check the link that help you with the steps to uninstall program to add or remove function below: how to change or remove a program in Windows XP: http://support.microsoft.com/kb/307895

  Method 2:

  Delete manually the filter upper and lower filters from the registry editor. See: (Section: fix it myself: your CD-ROM drive or DVD drive is missing or is not recognized by Windows or other programs:http://support.microsoft.com/kb/982116 )

  See also the link below: Advanced Troubleshooting for issues that occur when you are installing a new CD or DVD drive in Windows XP: http://support.microsoft.com/kb/314096

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• Do not remember the WPA key. Other computers on the network

  I don't remember my WPA key and reset isn't exactly an option since I have other computers already configured for the existing key. I don't mind reset other computers as well if I knew for sure that it works. However, there is a discrepancy between the length of the WPA key on my Linksys (indicated as asterisks-33) and the length of the WPA key shown on the laptop of my wife (indicated as asterisks-63).

  I am trying to add a Wii to my network. Our router is currently not broadcasting the SSID, but I typed the name of the router in the Wii in any case. (She even will be able to find a network that is not broadcasting its SSID?).

  I also added the Wii MAC address to the list of trusted computers.

  Regarding the password, I considered to change but I'm worried I might spoil my wife configuration.

  When I go into my wireless settings, I see that I use a WPA TKIP encryption which is 33 characters long. However, when I go into the configuration of the network on my wife's computer, she says that his encryption key is 63 characters (WPA - PSK TKIP). Why the keys of different length?

  Is it possible to change the encryption key on the router to something I'd remember? If so, that will enter my wife's computer? Wouldn't make sense that what I typed in the settings wireless of Linksys (33 characters) would be the same as mine rather than 63 characters?

  I'm so confused.

  Any help?

  First, the County of asterisk is meaningless.  Even the number of characters in your password is a secret, so all good programmer who wrote your wireless network card driver shouldn't have a number of astrerisk which corresponds to your password.

  Set your "broadcast SSID" "enabled."  Do you really think someone will lose hundreds (or thousands) of hours of time to break your password, just enter a router WPA?  As long as you use WPA or WPA2 and a password, you shouldn't worry about your SSID broadcast.

  You can use any key (sometimes called password or password) you want, but all the keys (in router and all computers) will be the same.  Ideally you should use a strong password.

  Choose passwords (keys): you should never use a Word from the dictionary as a password. If you use a Word from the dictionary as a password, or WPA2 can be cracked in a few minutes. When you take your login password and key encryption (password or password), you must use a random combination of uppercase letters, lowercase letters and numbers letters, but no spaces. A connection password, must be 12 characters or more. WPA and WPA2 passwords must be less than 24 characters. Note: Your key, password or password should not be a space in it.

  Most individuals should have their routers defined so that "remote management" of the router is disabled. If you must have this option enabled, then your password needs to be increased to a minimum of 24 random characters.

  An additional problem is that Windows XP requires SP3 run WPA2 (WPA with AES =).

• Network management problem, computer laptop Windows 7 will not find other computers on any network, however all other computers on the network can access Windows 7 laptop.

  Basically, the issue I'm having is that my laptop does not connect to any other computer to access the actions or other files.  Other computers on the network can access my computer laptop shares and files without any problems.  Operating system is Windows 7 Home Premium x 64.

  What I tried:

  restarted
  uninstalling and reinstalling the files and printers, sharing maps and restart after completion
  all disabled firewall
  tried with IPv6 enabled and disabled without change, so it is currently enabled
  tried on a Wi - Fi and the differences are listed below in the section work (work is wireless)
  able to ping other comptuers
  access to other computers is permitted by other computers

  problem extends over several networks, IE I noticed it at home last night and the followed problem my laptop at work this morning.
  The problem is slightly different on the two sites.

  At home:
  I can see the other computers on the network, but I am unable to access it, even if I have permission, but other computers can access to my laptop.

  At work:
  Cannot even find other computers on the network but they can find and access my laptop.

  I have worked on this problem of non stop for several hours and did much more than what is said, but I am unable to remember everything.  I should have been taking notes: P

  Here are the results of the ipconfig/all command (I removed the physical addresses for security reasons):

  Windows IP configuration

  Name of the host...: Radiation-G72
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless Network Connection 2 wireless LAN adapter:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft Virtual WiFi Miniport adapt
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. : hsd1.ga.comcast.net.
  Description...: Realtek PCIe GBE Family Controller
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  ... Description: Atheros AR928X Wireless Network adapt
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::f4e3:cd1c:6952:eb4d % 11 (Preferred)
  IPv4 address: 192.168.2.7 (Preferred)
  ... Subnet mask: 255.255.255.0.
  Lease obtained...: Thursday, February 4, 2010 10:50:32
  End of the lease...: Friday, February 5, 2010 08:29:36
  ... Default gateway. : 192.168.2.1.
  DHCP server...: 192.168.2.1.
  DHCPv6 IOOKING...: 234890707
  DHCPv6 DUID customer...: 00-01-00-01-12-4C-6E-91-00-25-D3-3D-FC-9A
  DNS servers...: 192.168.2.1.
  NetBIOS over TCP/IP...: enabled

  Tunnel adapter isatap. {1797D168-6FC8-4DDF-8338-4E214119C26D}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft ISATAP adapter
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Teredo Tunneling Pseudo-Interface:

  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  IPv6 address: 2001:0:4137:9e74:4ea:2920:b81a:cdc5 (Preferred)
  Address IPv6 local link...: fe80::4ea:2920:b81a:cdc5% 13 (Preferred)
  ... Default gateway. : ::
  NetBIOS over TCP/IP...: disabled

  Card adapt 6TO4 tunnel:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft 6to4 card
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Asked this question in the Windows 7 forum also because the problem was between windows 7 and Vista.

  Hello

  If it has started, you can try a system restore - an update "might" have caused the problem.

  1. try a system restore back to a point before that happened. And immediately thereafter enter
  Control Panel - Windows updates - top left settings and set it to download and informs you instead
  Automatic. Leave it until you are sure that everything is OK and then you can add them one at a time
  to troubleshoot BUT click right on and HIDE all the driver updates. Also stop at day of drivers like below
  and let this value - manually search for drivers when you think you need. (See how and why to)
  stop day of drivers below.)

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  To uninstall an update if you determine that there are problems - Panel - updated Windows - down left-
  Updates installed - uninstall

  I had completely forgotten the system restore!  While looking into the system restore, I found that when I moved into my new House and has cable Internet installed, the cable technology installed a program of comcast on my computer.  This caused me to not be able to connect with other computers.  After rolling back to install it before it works!   Thank you.

• \\mycomputername is not accessible. you might not have permission to use this network resource. comtact the administrator of this server to find out if you have access permissions.

  \\mycomputername is not accessible. you might not have permission to use this network resource. comtact the administrator of this server to find out if you have access permissions.

  Hello

  Thank you for giving us the opportunity to help you with the query.

  I understand the inconvenience caused, now that you have me with you I would take care of that.

  I suggest you refer to the steps suggested byJack MVP (replied on August 29, 2010)

  In the next thread that speaks of a possible solution to the related question.

  PC is not accessible. You might not have permission to use this network resource. Contact the editable from this server to find out if you have access permissions.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/PC-is-not-accessible-you-might-not-have-permission/26a1a479-8BA5-4213-9181-02364c884937

  It will be useful.

  Let us know the status, we are happy to help you further.

• Error: "\\(PC Name) is not accessible." You might not have permission to use this network resource... The specified network provider is not valid.

  Hi, this is a follow-up to the issue and my second attempt to find the solution. In addition, it is still connected to my first and second positions.

  My laptop that works with Windows 7 32-bit has 2 two natural questions:

  1. I can't access PC's on the network on the laptop itself and thus get an error:
  "\\(PC Name) is not accessible." You might not have permission to use this network resource. Contact the administrator of this server know if you have access permission. The specified network provider is not valid.

  2. When you make the file sharing Wizard, I get an error "your folder cannot be shared" and the only option is to click on 'Done '.

  I'm trying to share folders to another laptop that works with 64-bit Windows 8 but I think there must be a problem with the Windows 7 laptop. I can share and access all the folders of any laptop before.

  Thank you! Any useful response will be greatly appreciated.

  Hello Sevi,

  Thanks for posting your query in Microsoft Community.

  I understand that you have problems to access the specified network.

  But, I would like to know some information related to this topic to help you better.

  (1) is connected to a domain of the computer network?

  (2) is your computer connected to the homegroup?

  (3) have you been able to access the specified network previously.

  In the meantime, please follow the suggestions mentioned by Fazil M on May 15, 2012 and check if this is useful.

  Error "\\computername\f is not accessible.  You might not have permission to use this network resource"when accessing to Windows XP computer via a working group

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/error-computernamef-is-not-accessible-you-might/a8db7f8c-6a7b-462D-B7F5-48707ae6b1f8

  I hope this helps. Otherwise, feel free to write us again and we will be happy to help you.

  Thank you