Purchased airport Time Capsule in the USA and the cord specifies 125V. I can hook it up to 220 V?

Similar Questions

• I just can't get my Airport time capsule on the internet.

  I bought an airport Time Capsule and a MacBook Air, have set up their, I access my files inside the airport TC, but I can't access the Web, away from home.

  What should I do?

  It is necessary to have a Mac at home connected to access?

  Setup using Airport utility it does not appear to me the ability to access over WAN. How can I do?

  I already configured the back to my mac option.

  Can someone help me?

  Please take a look at the following airport user tip for, at least, three methods to access your Time Capsule from a remote location.

• our airport time capsule connects to computers and the internet, but does not record on the usefulness of the airport as being there - is it dying or is their a reset?

  Our computers connect via wifi to a capsule of time to the airport and to the internet, but can't find the time capsule, nor can its hard drive. Y at - it a reset, we can try or he dies. It's only a couple of months.

  Turn about your Airport Extreme for 15 seconds and then power back on. As soon as you see the green light, you should be able to see him for a minute or two in the Airport utility. In the affirmative, and see if you have Back to My Mac active. If so, disable it by removing all the e-mail addresses of the back section of my Mac. Then update your Airport Extreme. Work quickly.

  Many have started having this problem within the last week, probably because Apple changed something in its servers CCMM. A real difficulty would come from Apple, but it should work if you currently have active CCMM.

• How can I connect my Airport time capsule to the nbn optus

  I just got the NBN Optus connected and time capsule doesn't seem to work, can anyone advice on how to connect. I connected to a modem (Sagem Fast 38640op) with cable but the mac does not expect a return to the top

  You should do a full factory reset on the TC...

  Repeat the installation... and it should work correctly in bridge and create a wireless network.

  The Sagemcom really poor wireless but you can leave it on... use it for your network wireless of comments.

  This is my normal configuration guide... but there are a few specific pieces to network problems with the operating system later as Yosemite or El Capo.

  Start from a factory reset. No files are lost on the drive hard in doing so.

  Universal factory reset

  Turning off the TC... That is, remove the power supply cord or the power at the wall outlet, wait 10 seconds... Hold the reset button... be nice... Turn on always even now in reset... and keep holding in for another 10 seconds. You may need assistance because it is difficult to hold in reset and power on. It will show the success quickly flashing led front. Release reset... and wait a few minutes for the TC to reset and return with the factory settings. If the front LED flashes quickly you missed and simply try again. The reset is quite fragile in these... Press the key while it is just click away and not more... I've seen people bend lever or even break. I use a toothpick as a tool.

  NB. None of your files on the hard drive of the TC are removed... This simply clears the settings of the router of the TC.

  The installer the TC.

  And then redo the configuration of the computer with the Mavericks - Yosemite - ElCapo. (MYELCAP)

  1. the use of very short names... NO APPLE RECOMMENDED names. Without the space and pure alphanumeric characters.

  for example TCgen5 for the base station and the name of the TCwifi wireless.

  If the problem is using wireless TC24ghz and TC5ghz with fixed channels as it also seems to help stop the nonsense. But it can be tried in the second round. IE, plan on a first and second series of changes to fix this... If all goes well... I note other steps can you tour2.

  2. use all passwords also consistent with 1. but maybe a little longer. IE 8 and 20 characters of mixed cases and numbers... no alphanumeric non-caracteres.

  3. If the TC is router, you can ignore this point. It is only a problem when the TC is bridged.

  If ensure that the TC is always the same IP address... you will need to do this on the main router using a dhcp reservation... or a bit more complex setup by using the static IP address in the TC. But it's important for deriving from intellectual property in all directions when MYELCAP do not remember his name for 5 min after a reboot done for poor network management.

  4. check that your share on the computer name does not change... Make sure that it is also in line with the above... short without space and pure alphanumeric... but this change will mess up your TM backup... so be prepared to make a new, full backup. Sorry... keep this one for the second round, if you want to avoid a new backup.

  5 attach the TC disc into the computer manually.

  In Finder, go, connect to the server in the main menu,

  Type in SMB://192.168.0.254 (or whatever ip of TC is that you made static. It's a default router 10.0.1.1 and I encourage people to stick with it unless you know what you're doing).

  You can use the name... SMB://TCgen5.local where you replace TCgen5 with your name of TC... local is the default domain of the TC and does not change.

  However the names are not so easy as... the IP address nor reliable. They are not at least not in Yosemite. The field can also be a problem if you are not clogged or wireless directly to the Treasury Board.

  6. ensure that IPv6 is set to link-local only in the computer. For example wireless open network, wireless and Advanced preferences / TCP/IP... and the difficulty of IPv6. link-local only. Do the same for the ethernet if you use it.

  

  It is a lot more jiggery pokery, you can try, but the above is a good start... If you still find not reliable... don't be surprised.

  You may need to do more work on the computer itself. for example, to reset the NVRAM/PRAM/SMC... helped some people. A clean installation of the operating system is also useful if you update installed.

  https://discussions.Apple.com/message/29202159?ac_cid=ha123456#29202159

  Let us know how you go.

• Time capsule on the Sierra

  Hi all

  Since I upgraded to Sierra, Time Capsule (TC) is not automatically connect to my MBP. Now every time, I must click on TC icon in the side bar of the Finder, and then click the Connect button and in the password again popup click on connect (fortunately I don't have to enter the * password each time). Before the upgrade, it has never been a problem and TC would be always connected.

  I have repaired permissions while logged in; First aid also made via recovery mode; TC restarted; MBP rebooted nothing helps.

  Ask any entries, while I continually connected TC & save the MBP

  Thanks in advance

  Open AirPort Utility, and then select your Time Capsule, and then click change. Then select the disks and connect using his password. Remember that the password is saved in the keychain.

  These documents Support from Apple can help:

  Check, repair or erase a disc AirPort Time Capsule - Apple Support

  and

  If you cannot back up or restore your Mac with Time Machine - Apple Support

• Airport Time Capsule HD access

  I have an AC of 802.11 airport Time Capsule 3 to, PartNumber: ME182LL/A, and I want to save my MacBook Air by Time Capsule app.

  In addition, I use it as an external hard drive, moving some files to the airport Time Capsule using the Finder.

  I use physical conection from my MacBook to the trough of Time Capsule a RJ45-USB converter.

  But I am extremelly experiencing a lot of time to access my files using the Finder.

  Do you have an idea how I can fix this connection?

  Do you have an idea how I can fix this connection?

  I guess that your Mac has a Thunderbolt port.

  Use a Thunderbolt for the Ethernet card.  It's up to 10 times faster than the USB adapter. Your actual speed will be 4 to 5 times faster than USB.

  Maid in Gigabit Ethernet Adapter - Apple

• Time Machine (on Mac) does not detect the airport Time Capsule

  Originally posted on the page of the airport, but seems to be the better question for this group. Sorry for the double post

  Looking for advice on how to get the Time Machine utility for access to my Time Capsule. I use an iMac in late 2012 with MAC OS 10.12 TimeCapsule is 2015 7.7.7 running latest firmware. Airport utility is the latest firmware 6.3.7.

  When I run the application Time Machine, Time Capsule is not detected. I tried the two WiFi and with cables connected Ethernet (not tried USB yet) and my Time Capsule doesn't have a lightning bolt or firewire ports.

  Open Airport utility & see the airport time capsule. I can see all connected devices, including the MAC, but no prompt activation Time Machine on the Time Capsule.

  I recently used TM on this iMac with a G-Technology drive. It auto detects the time machine and executes a back up. But airport Time Capsule will not.

  Any suggestions?

  Sierra has been problematic with the TC.

  1. make sure you don't have any charge virus protection software. In fact, I would say that disable all software 3rd part at the moment.

  2. make sure that you can actually write to disk of TC.

  Attach the TC disc in the finder and copy a file on disk, you can delete it later... It's just to ensure that you have full write permission. If it does not for the most part, you won't be able to use Time Machine... If you can then try TM immediately...

  Just to be clear, the TC is a network device. You have tested with ethernet and wireless... Ok.. They are only suitable methods. You cannot use USB. And clearly, TC has never had nor will never be ports Firewire or lightning.

  3. no chance that a reset complete TC. This will not delete the files on the hard drive, but you must make sure that the device is configured on the current computer.

  4. There are many positions in these days... read through them and do some research. Sierra is a bleeding edge new... So wait you to spend a lot of the precious liquid if you choose to be an early adopt.

• HOW THE AIRPORT TIME CAPSULE WIRELESS NETWORK IS PROTECTED?

  I implemented the airport Time Capsule, using a DSL modem connected to the internet as its bridge.  MacBook Pro was used for initial set up by the bolt of lightning to Ethernet connector and then disconnected and works perfectly.  Now, I would like to use Wi - Fi for my Samsung phone not iOS.  On the Samsung wireless I connect to my home network using a password.  Well, I don't think that a password was never set.  How can I configure my wifi at home to establish a password?   I don't think that the modem settings should enter in solving this for me, but I'll add that the modem required a static IP address be entered for this connection when its router features have been disabled for the connection of bridge.

  If the Time Capsule (TC) provides the wireless network, then you can secure it using AirPort Utility, as follows:

  • Run the AirPort Utility.
  • Select the TC and then, select change.
  • Select the wireless tab.
  • In the wireless security, select the type of security. I highly recommend that you choose: WPA2 Personal
  • Enter a password in the field password wireless. Enter the same password in the verify password.
  • Select Update.

  

• Airport Time Capsule and WD MyBook

  I'm a newbie Macbook Pro owner, about a week now, El Capitan running.

  I've just hung up my Airport Time Capsule (3 t) and it seems to work, as the reports of Time Machine backup complete.  I am also connected to the WiFi Airport.

  The Installation Guide says I can connect a hard drive via the USB port.  I have connected a WD MyBook USB port; It is in the format exFAT and contains the data from my old computer to Windows 7.

  What should I do to make this available for the Macbook Pro?  I don't see anywhere in the finder.

  The time Capsule cannot read USB drives to NTFS or exFAT format. Plug it directly into the Mac.

  (144647)

• Parameter problem to the airport Time Capsule

  Already, we currently have a WiFi system with a NetGear router and a modem from Time Warner.

  I just want to use the airport Time Capsule to back up my Mac.  My husband has a PC.  I followed the instructions but the airport still comes up in the utility.

  Mac OS X El Capitan 10.11.6 and the latest 802.11 ac 3 TB so I don't know what I'm doing wrong.  I plug an Ethernet cable at the airport, then in the Modem - nothing after I plug the power - Amber flashing light.  I have changed ports unplugged and plugged back in French - restart the Modem.  Nothing works.  I bought it so it would work straight out of the box - so far, I have spent a lot of time trying to understand it.

  Any help would be so appreciated!

  Hello

  Try the help in this support article > Wifi hotspot: understand and resolve a blinking light of amber status - Apple supported

• Why didn't I go and turn my Airport Time Capsule to be able to backup?

  Hello.

  Why didn't I go and turn my Airport Time Capsule to be able to backup? It has been like this from day one. At the point where I keep my iMac off for a few days, my Time Capsule airport must be enabled and the new in order to save. Any suggestions?

  Concerning

  Simon

  Hello Ladro Maltese,

  Thank you for using communities of Apple Support.

  If I understand your message when you shut down your iMac a few days and then go back on you have to turn off your Time Capsule, then on again as well. I know how it is important for you to be able to have your Time Capsule works well. The first step that I recommend is to make sure that your Time Capsule firmware is up to date.

  This article includes information about how to manually and automatically check updates the firmware for your Time Capsule:

  Keep your base station to day.

  After updating the firmware see if the problem persists.

  Best regards

• Cannot move the files, photos at airport Time Capsule

  Hello

  I want to transfer files, photos of my Time Capsule but I don't see anywhere on my macbook. I think that something I messed up when I was put in place at the time of Christmas trees. I'll start from the beginning. Before I bought my time capsule I was connected to the internet through my wireless router, name: GMZ-83313. After that I bought my Time Capsule I set up and connected to the internet. Problem is that I have 2 networks who I can connect it is: GMZ - 83313 and Daniel Wi - Fi network (finally...) I have three really because I started to play with it more and I have network of Wi - Fi for the 3rd networkDaniel 5 GHz ;(

  I just want to add that yesterday I was able to transfer photos from my time capsule and it showed here where you can see GMZ-83313. Yesterday, it was Ant Time Capsule of Daniel it was working fine.

  

  I'm lost please help. I have attached a shot of my airport utility screen:

  

  Click gmz-83313 under the Shared heading in the Finder window

  A folder that represents the Time Capsule... hard drive that is named 'Data', unless you have changed the name... appears in the window on the right

  Double click on data to open the player and install it on the desktop computer

  You can drag and drop the files to the disc on the desktop icon or the open window

• Need help with the implementation of a replacement airport Time Capsule

  Hi... Recognizing the help. My 1 TB airport Time Capsule (ATC) crashed and I bought a new 2 TB ATC to replace. In my preference system, Time Machine reflects that my ATC 1 TB is still active. How to pay safely my 2 new cases of tuberculosis ATC to replace the 1 TB ATC?

  Assuming that you 1. already connected the new TC on your network, and/or 2. you were able to save all data on TC 1 TB, or simply do not take care of him You can just open Time Machine preferences, turn the Time Machine off, and then select the disk in the new time Capsule. A brand-new first backup starts to run, and it will certainly take time.

  Another option is to connect the new TC on ethernet directly on your Mac and then select the Time Machine preferences, this will speed up the first backup.

  In case you were able to archive the old backup and transfer it to your new TC, you will continue your backup schedule by simply selecting the new TC in Time Machine preferences.

  I hope this helps.

• What is the best way to connect a time capsule from the airport to an existing dsl router?

  I have a Netgear D6300 router with built-in ADSL modem and I'm getting a time capsule from the airport. I thought to put the D6300 in Bridge mode and connect the TC via a ethernet cable but my netgear router is kept in a metal TV armoire or I asked myself if I put on the floor and used to extend my existing wireless which is a little spotty on the floor, but I didn't know if the connection on the hard drive would be too slow. However I read in another post is no longer that apple supports the extension of networks of "no apple"?

  The time Capsule will connect to the Netgear router using a wired Ethernet cable connection, permanent... no matter how you decide to configure things.

  Regarding the location, Time Capsule can be located just about anywhere that it will allow an Ethernet connection. If you want to time Capsule to "extend" the wireless Netgear, and then configure the time Capsule to create a new wireless network that uses the exact same wireless network name and password than the Netgear router. The result will be a network of 'big '.

  Should be a lot more work, but assuming that the Netgear gateway can be configured to work as only a simple modem, the Capsule can be configured as the primary network router.

• My LAN airport Time Capsule 802.11ac began to abandon their studies on the Cox network.

  My local network that the internet began to abandon their studies in airport Time Capsule 802.11ac associated with my network of Cox. The green light stays on. Unplug it and plug it back bring it will return immediately.

  I disabled IPv6 on the suggestion of the counsel of COX because Cox and Apple have a problem with these capsules of time regarding IPv6 and IPv4 is supposed to work.

  It is a question of cox or should my time capsule service?

  This modem do you have? Brand and model please.

  It may be a contributing factor, where the transition to IPv6 is causing issues, but raised another problem.

  He has also reported a DNS issue... Please fix the DNS servers of your TC... (IPv6 is set to link-local now in your TC?) Assign the values google DNS and see if it improves things.