PXI-2510 has no reaction when using NI VeriStand

Similar Questions

• PXI-4071 sampling too slow when using a hardware trigger

  We use 3 PXI - 4071 s in parallel to measure with accuracy of high voltages. The program is written using LabVIEW 8.5.1.

  An additional test condition has been added which requires the use of a quadrature decoder and the synchronous DMM.

  We thought it would be simple, using backplane trigger 0.

  However, something odd happens.

  With a low-cut VI that uses a single DMM, we get 100 microseconds time to sample running with internal triggers. However, if the overall relaxation or trigger of the sample is set to TTL0, the sample time becomes so 5.1 milliseconds. It seems very strange that even just definition of overall relaxation, expected to affect only the time of the first sample, not the time between samples, has that effect. The plug for the DMM also said, that the maximum trigger rate is of 6 kHz.

  We have confirmed this reported sample time is independent of the speed of the clock actually connected to TTL0. If the clock is faster, it gets the reported sample time. If it's slower, the samples occur on the edges of the clock.

  Does anyone know if there is a parameter that has a default that changes based on the source of command and can be changed to work around this problem, you?

  I found the solution to this.

  Over time the value-1, the DMM uses a short value (less than 100 US) to set hour when, in modes triggered internally. However, he used much longer (about 5 ms) when the value - 1 and with the help of a hardware trigger.

  If the running-in is set to 1e-5, i.e. 10 microseconds, "the estimate" returned for conversion period goes from 5.1 ms 100, we and conversions actually occur at a rate set when clocked with trig 0-5 kHz

• "[White] has stopped working" when using Big Fish Games

  I've had Big Fish Games on my computer for over a year now and it has always worked well, but recently, when I downloaded games and tried to open them via the games Manager, I get a message that says "[White] has stopped working".  There is no error code or the name of the program, just a space empty.  Windows is trying to find a solution then is to say that he manages.  The games does not open and I end up having to delete them.  I tried to re - download but it does not work. I also tried looking at permissions for games using Microsoft various 'fix' programs, but no problem is found.  Can anyone help?

  Debs

  Hi Debs1980,

  ·        What is the operating system?

  1. check for the error code and the name of the program of the event viewer, see the link below: what are the information contained in the logs of the event (Event Viewer)?

  http://Windows.Microsoft.com/en-us/Windows7/what-information-appears-in-event-logs-Event-Viewer

  2 start the clean boot computer and check if the problem still persists. Link below will help you to start the computer in clean boot:http://support.microsoft.com/kb/929135

  If the problem does not persist, you can continue with step 2 from the link above.

  Make sure that you reset the computer in normal mode in step 7.

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Is there a function "when used"?

  Bridge (CC) has a function "when used" for the linked files?

  If I have a graph related to several different InDesign documents, can bridge show me where the graph is used?

  Thank you.

  Hi Kalaka,

  I am not afraid. Bridge cannot display a list of files related to an identity document given when you target, which is in fact thanks to engineers in ID. He has no idea where you might have used each file. Be nice if there was something that could track down, wouldn't it?

• I have problems with my Apple ID when you download applications, that it is said that your ID Apple has not yet been used in the iTunes Store

  I have problems with my Apple ID when you download applications, that it is said that your ID Apple has not yet been used in the iTunes Store

  What exactly is the problem? You are also being invited to review the account and enter payment details? If you did you are your details accepted - if they are, you should be able to remove them then.

• Outlook has started to get a connection not approved when using firefox

  Outlook started having no reliable connection error when using firefox. Not sure why it started, but all the few minutes that it times out and I have to re - open outlook from google. He does not receive this error on IE or firefox android. I use win 7. I talked with microsoft and they say it's a problem of firefox not outlook.

  I tried the things:
  -Updated firefox
  -Updated antivirus
  -antivirus scans
  -disable the anti-virus
  -from firefox in safe mode.
  -clear all the cache and history
  -Disable all add-ons
  -system restore
  -past by mistake "untrusted connection" on the help of mozilla (does not solve it. There is no option to allow the certificate)
  -search on the net for a similar problem (found nothing)

  So far, it has been like this for a week and its starting to piss me off as it happened out of the blue.

  I solved the problem for someone else who has the same problem.

  Options - troubleshooting information - reset firefox

• Firefox Help my firefox top bar has been changed, I used to be able to get the file to bookmarks Format printed, and other services that I have found useful when you take information from the internet, where they went, I want them back?

  Firefox help

     Search
  

  "Found 0 results for" my firefox top bar has been changed, I used to be able to get the bookmarks printed Format file, and other services that I have found useful when taking information from the internet, I found bookmarks to the right of the new game to the top, but it seems not instantly friendly where they went, I want that they come back? »

  See:

  • https://support.Mozilla.org/en-us/KB/menu%20bar%20is%20missing

• When using a 2010 macbook pro and a mini display port to hdmi adapter, will be the macbook pro display be sent to a TV that has hdmi inputs, or do you need a keyboard command

  When using a 2010 macbook pro and a mini display port to hdmi adapter, will be the macbook pro display be sent to a TV that has hdmi inputs, or do you need a keyboard command

  Yes it will be displayed.

• RF Mux PXI-2546 driver stops working when DAQ SMU-6259 is used.

  Hi, I am experiencing a very strange thing. I have a system with two 1065 equipped chassis with about 15 different instruments.

  It was working fine and has done for several years. Today the SMU-6363 DAQ crashed, I tried to replace it with a spare DAQ SMU-6259. I started with switching just the daq spare in but then the computer crashed every time during the installation of the pilot SMU-6259. So I thought that I need a driver update and installed DAQmx 15.1 (previous version was 14.5). It has not made any change. Computer always crashes constantly. Finally I found that if I remove the PXI - 2546 Rfmux in the SMU-6259 DAQ system will install and work properly. But now Rfmux PXI-2546 will not work when acquiring data SMU-6259 are installed on the system. I can get the Rfmux to work if I take the DAQ and vice versa.

  Why is it like this and what can I do to solve?

  I do not understand why a PXI-2546 Rfmux and an SMU-6259 DAQ interfere with one another.

  / Erik

  Hi Anton, thanks for your answer!

  Yes, it's very strange. I narrowed down it to these two devices. I got the blue screen during the installation of the Windows driver. So I tried first update the driver OR DAQmx. Who did not have any change.

  Then I tried to roll back the NOR-DAQmx driver to a previous version. Crashes stopped then, but I could not both devices to work simultaneously. In the windows Device Manager, he showed a problem for the NI DAQ PXI-2546 peripheral device. I don't know why a mux is considered DAQ hardware either. The description of the problem says "some free resources". If I could get the Rf mux to work if I unplugged the daq and vice versa.

  For the last two days, I was reinstall the system from scratch. I'm not done yet because it takes so much time to do this, but it seems to be ok now. But what a pain. I started with just the driver Rf Mux (Switch).

  To do this I had to download almost 3 GB! For a 2 x 4 x 1 Mux driver. Then, the driver for the installed switch some NOR-DAQmx which I had to then update and download even more.

  I think that NEITHER makes it very complicated with the pilot stuff. Instead of having these huge drivers packages which supposed to cover everything, it would be better with the smaller specific device drivers that could be easily found on the web under each device.

  In any case I hope it should work ok now. I wonder what will happen when I get home my repaired SMU-6363. Should I plug it in or simply do not bother because I could face the same problem again?

  / Erik

• The PXI-2510 module for 2013 has different names

  Hi, I'm upgrading of VeriStand 2011 to 2013. I downloaded the new device custom of the add-on for the injection of PXI-2510 or http://www.ni.com/example/31248/en/unit. I noticed, however, that the channel names are now different. Instead of strings being 'Ch. 00' thru 'Ch. 67', they are now preceded by the word "Fault", becoming "fault Ch. 0" to "Fault Ch. 67", without the zero not significant.» Therefore, it is difficult to make an upgrade without breaking the mappings for each channel. There are several other functional changes to equipment custom 2013? At the moment I intend just mass compilation my 2011 version into something usable for VeriStand 2013. Thank you.

  Hey Harris,.

  I was surprised to hear this feedback as custom device actually only has a source code that is built in 2011, 2012 and 2013. So there shouldn't be any change in behavior.

  Looking into the source, the chain is indeed "fault c." to which is added a number: ".

  

  So I think that if you have downloaded version 2011 from the Web site, you would also see this behavior. The channels are not rename protected. You are sure that the user not the do not rename them at one point? Speaking of which, you should not re-add the device custom during the upgrade of your system definition. If the custom device was present in the definition of system of 2011, it should be also present in the system 2013 defintiion. Make sure that the custom device is installed on the computer and you should be good to go.

• I am facing a problem with the beep.vi. I have a DAQ program, which acquired the signal and compare it to a threshold value. When a signal is out of range, a Visual and sound alarm has occurred. I use the VI beep.vi to generate the sound.

  I am facing a problem with the beep.vi.  I have a DAQ program, which acquired the signal and compare it to a threshold value. When a signal is out of range, a Visual and sound alarm has occurred. I use the VI beep.vi to generate the sound. Everything works fine except the sound alarm. It gives the table 1 d of type mismatch. I tried to fix this by placing it in a box structure. But it still does not work. If someone could help? Please find attached my VI. Best wishes to all visitors to the Forums of Discussion OR.

  Ihab El-Sayed

  published here: http://forums.ni.com/t5/LabVIEW/Playing-sound-based-on-exceeding-a-threshold-value-1D-array-data/m-p...

• Cannot install OS: "this identifier Apple has not yet been used.

  I just got my first Mac yesterday, a mid 2010 Macbook of opportunity. It's in great shape, works great, I was briefly very satisfied with my purchase. Then I tried to reformat/reinstall, as it does whenever purchasing a computer used.

  I followed the instructions here: https://support.apple.com/en-us/HT204904 and when I got to the step three, after the failure of the hard drive, it wouldn't let me install the operating system. He wanted to connect first with my Apple ID, so I did an Apple ID, but now it keeps giving me an error "this identifier Apple has not yet been used in the App store" and then it gives me the opportunity to cancel or "review". Click Cancel simply cancels the installation, just by clicking on review also cancels the installation.

  An ID is not necessary, but there is no way I can see to avoid it say the instructions on this page. It was suggested that maybe I could avoid the connection on the way to recovery, rather than recovery of the Internet, but the Cmd + R and Cmd + Option + R give recovery of the Internet. I don't see any way to get to the regular recovery.

  I had a suggestion to install from the disc, but I have not all discs. If I could download it from somewhere and burn them then that would be nice, but the instructions on this page are pretty clearly that it should not be necessary to use disks. I should be able to do without signing in.

  So... what upward with who? Where should I go from here? Is it possible to do a regular recovery? Or bypass the Apple ID thing?

  < published by host >

  "a mid 2010 Macbook opportunity."

  "Cannot install OS:" this identifier Apple has not yet been used.

  It's the property > change owner of a Mac of opportunity

• This identifier apple has not yet been used with the App store.

  I bought my macbook pro to my brother and always used without my Apple ID and then I decided to restore the macbook to the factory because of some problems with the performance setting, when I hit install OS X Yosemite on the disk, it asks you to login Apple ID and when I try to login with my account , he says "this identifier Apple has not yet been used with the App store" Please check your account information, when I hit "see" nothing happens and it of kind of stuck and makes me restart the process and enter my apple ID and password. "

  I don't know what the problem is and now I can't open my macbook to use

  Because the computer has been configured using Apple ID of your brother, it is bound to this ID. If you have never downloaded Yosemite, you can not install it. Ask your brother to insert his Apple ID, so you can get the computer operational again. Then, go to the App Store, sign in with your ID and check the purchases tab to see if the Yosemite is an option. If this is not the case, download El Capitan and see if it will install. If you want to do a clean install, quit the installer and the program below allows you to create a bootable USB key. Boot from it, wipe the hard drive and then install El Capitan. When you restart normally it will be your computer. See also the link for sale.

  Bootable USB Flash Drive-Diskmaker X

  Sale of old Mac (4)          Apple support

• Strange glitch Visual on the taskbar when using Firefox

  Hello

  I feel a strange glitch Visual on the taskbar when using firefox.

  Please take a look at this short video because it shows the problem, it's almost impossible to show in pictures.

  https://DL.dropboxusercontent.com/u/12595174/VIDEO0016.3gp

  I use firefox on Windows 7 Pro 64 bit v36.0.1. Video card is an ASUS R9 280 X using the latest drivers from AMD 14.12 Catalyst Omega Software.

  Motherboard is an ASUS M5A88 with 16 GB of ram and a processor of 6300 FX.

  It is a new construction that I have implemented in the last 24 hours, and this behavior was not present on the system using the same version of windows, firefox and even map chart and drivers. But on another card mother and CPU. Previous Board of Directors has been
  M4A79XTD EVO with a Phenom II X 4 955BE.

  The glitching does not occur when it is on the desktop and firefox is closed. It will not occur when you use IE - 64 nor does it when I am using the steam software or any Explorer windows/opening files.

  All the motherboard drivers are installed correctly, the integrated graphics card is disabled in the BIOS. I disabled the settings of firefox for hardware acceleration, smooth scrolling and text... to see if it was the question. It wasn't.

  I'd appreciate any help to solve this... Really, I don't want to use a different browser but it's bad enough and quite distracting to really annoy me, and I don't see any alternative.

  Thank you very much.
  H

  Hi jscher2000

  I was about to post a reply, because a friend suggested that maybe that's a rendering of issue rather than a firefox one video card even if it's strange how it affected firefox only. I didn't have a chance to test it on Chrome as it is a new construction and I don't want to install the software, I do not use.

  I went to the Manager of catalyst and had a glance to the settings. I changed something, but no help... I then started to make a simple change and test until I found that the activation "gpu up-scaling" in the properties of digital flat screens has solved the problem.

  I am now free twinkle

  Thanks for your quick response however.

• All of a sudden my settings in Firefox and IE has been set to use Proxy. Breach security or virus?

  When I turned off my laptop everything worked fine. When I turned it on again. It was not possible to connect to any website that settings in both Firefox and IE has been changed to use a proxy server. 127.0.0.1 IP ADDRESS. Breach security or virus? Or maybe could I possibly, changed the settings by chance?

  It is difficult to accidentally change the setting of something you
  normally not have access. I say add/bad-ware.