PXI-6515

Similar Questions

• PXI does not recognize PXI-6515

  
  

  Thanks Napoleao,

• PXI-1042 q with controller 8331

  HI........

  I want to configure a single chassis PXI-1042 q with controller PXI-8331. I have connected 2 I\O Digital Digital card (PXI-6515) and 1 card(PXI-6514) I\O to this chassis. And I have connected this chassis to my PC with the serial cable (OR standard cable on COM 1) on my PC. But the problem is when I opened and Measurment Automation explore it dose not detect chassi eithre or any card I\O.

  I installed OR version 4.6.1 platform services.

  An obsrevation is led RX ON Chassi and dose led TX ON PC does not illuminate.

  Please guide me step by step configuration.

  Thank you

  Pravin.

  PBL,

  The PXI-8331 is not a serial interface, even if the connector looks like it, so it should not be connected to COM1.  It works when it is connected to a PCI-8331 in your host PC.  The cable must be a MXI-4 cable, for example 190957-03, not a cable series.

  If that's what you do, please report the LEDs on the two cards.

  -Robert

• Generation of functions NI PXI-6704

  Hi forum people,.

  I have a question about the generation of functions, to be precise, without the adequate hardware PWM. I'm under NI SMU-8135 embedded controller in a chassis NI SMU-1078. It is equipped of PXI3 OR-8532 (DeviceNET), NI PXI-6515 industrial digital I / 0, NI PXI-6225 (M: multifunction DAQ series) and NI PXI-6704 (analog output). My question is: can I generate PWM of any of these materials?

  Thank you!

  Start with help > find examples or search the site of pwm.

  Fix your code if you want to help with it.

• Read the PXI-8431 channels using LabVIEW

  
  

  Hi Marc,

  The examples provided with LabVIEW and DAQmx drivers are very detailed and comprehensive to demonstrate how you can use cards. To join the Finder of the example, start LabVIEW and select help > find examples.

  When you load the example Finder, make sure you browse by task.

  For the programming of DIO:
  Navigate to hardware input and output > DAQmx > digital measurement. There is a few screws. Make sure you look in the list of requirements to see the example works with the PXI-6515.

  You can also visit the following links to learn more about programming DAQmx:
  Getting started with NO-DAQmx
  http://zone.NI.com/DevZone/CDA/tut/p/ID/5434
  Learn 10 functions in NOR-DAQmx and handle 80% of your Applications of Data Acquisition
  http://zone.NI.com/DevZone/CDA/tut/p/ID/2835

  For series programming:
  Navigate to hardware input and output > Serial
  You will find most of the screw example it can be used with the PXI-8431.

  I hope that helps you to get off the ground!

• Can't see the new PXI cards on my remote

  I am currently reconfiguration from a 1006 PXI chassis for a new program. It was adding three new cards in the system. The configuration is currently:

  1 - controller NI PXI-8176
  2 - OR PXI-6040E
  3 - OR PXI-8421
  4 - OR PXI-6533
  5 - OR PXI-6533
  6 - OR PXI-6533
  7-
  8 - OR PXI-6713
  9 - OR PXI-6040E
  10 - OR PXI-2590
  11 NI PXI-4204 (new)
  12 NI PXI-6515 (new)
  13 NI PXI-2570 (new)

  Each card can be seen by MAX on the PXI chassis when started in Windows very well. However, when I start in the program in time real and you connect to the chassis using my office (and MAX), the remote system appears well, but with none of the new cards listed. (They are listed in the vacuum or unknown). I am at a loss to get these cards recognized. They seem to be installed correctly, as the own of the MAX station can see them. But apparently I missed a step in their installation... I am relatively new to this, can you help me?

  Thank you
  Dan Marlow
  General Dynamics Land Systems

  Bingo.

  That's all. Cards have been recognized immediately once I upgraded to LabView 7.1 and real-time 7.1 7.2 OR-DAQ.

  Thanks, gang!

• HP Photosmart 6515 Scan-Advanced_Settings checkbox is not operational for several PDF pages

  HP Photosmart 6515, Windows Vista 32-bit Home Edition,

  HP Photosmart program cannot scan multiple pages in a .pdf file, because the disabled in advanced settings check box does not allow multiple pages to analyze;  not "add files +" button/icon never appears as it does SI Documents-To-E-Mail is selected. ".  It at least shows me the missing button, which never appears in the selection of the PDF Documents.  Box of documents-To-PDF is DOA.

  So I ran the HP Photosmart update under all the programs/HP/update, and it updated and still does not work.  Update says now "up to date".

  -Yes, I tried to Scan-To-Computer, since the touchscreen HP 6515, and he asks me it indeed if I want to scanb another page.  However, it is fast to the time-out that I can't get another page on the glass or even open the cover completely before it goes... after pressing 'Yes' (I want another), "Scan" appears just long enough to tease and taunt me by saying "Ha ha", like Lucy with the football Charlie Brown.  No parameter to control the duration of the waiting period?

  Hello

  Multi-page analysis only supported on 300 DPI or more low-resolution.

  Go to the HP software and select scan a Document or Photo.

  Select the PDF option and ensure that the preview screen is displayed.

  Reduce the resolution to 300 DPI or below and click Scan. then the pages option Add should appear.

  Kind regards

  Shlomi

• Photosmart 6515 does not print black ink after replaced the cartridge

  I am very frustrated! I can't get my Photosmart 6515 print black ink.

  Our school sends the documents by e-mail now that we have to print at home. Ideal for them, but not for me. They are usually in PDF format, so I do not have the ability to edit and change the blue color to print, either.

  I only use HP cartridges on this printer. I know it's more than a year, in order to call phone support will do no good.

  I replaced both cartridges and now it shows black ink completely full, but when I print the printer status report, black is not displayed. Black does not appear on the tool pages, either.

  I tried the command "clean printhead" several times. I unplugged and waited. I took all the cartridges. Connections look clean.

  What should I do to perform a partial reset or full?

  Hi Photokool,

  I understand that this has been a frustrating experience for you, and I want to help him.

  I will send you a private message, please check the little envelope on the upper right of the forums page to check your Inbox of Forums.

  

• Does anyone know how to change CMOS battery is used in a Compaq 6515 b?

  Does anyone know how to change CMOS battery is used in a Compaq 6515 b?

  Hello

  This is the RTC battery on the book next (page #66):

  http://h20628.www2.HP.com/km-ext/kmcsdirect/emr_na-c01566982-9.PDF

  Kind regards.

• Compaq 6515 b broken mainboard

  Dear HP customer service

  My contact details are below:

  product: Compaq 6515 b

  s/n: [edited by Moderator]

  p/n: gm923pa #akl

  My motherboard is broken.

  What is replacement cost?

  I had searched on the internet. The prices vary a lot.

  I live in Thailand. And I don't have that one way is to contact them by phone.

  No email or forum available. If I had better ask people in the internet and communicate with them again.

  The cause is VGA. Since it is integrated on the motherboard, so I have to replace all across the Board.

  You have an idea?

  Find another part that is equivalent to it?

  If it's so cheap, I'll try. I love using the keyboard and touch buffering more than portable modern.

  Best regards

  Tiras

  Here is the Manual:

  Manual

  There are two possible mothers depending on whether you have the chip WWAN (mobile cellular):

  For use with computer models HP Compaq 6515 b have WWAN (including WWAN
  housing module) 443896-001
  For use with computer models HP Compaq 6515 b without WWAN capability (does not work
  includes the location of the WWAN module) 443898-001

  I'll assume you don't have the cellular mobile or do not care if you have:

  http://www.eBay.com/ITM/new-genuine-HP-Compaq-6515b-6715b-AMD-PCI-laptop-motherboard-443898-001-/350925768422?PT=motherboards & Hash = item51b4ce46e6

  Above is a link to a motherboard for $40US and they ship anywhere in the world, so even if the expedition in Thailand is $ 50 you will get always for less for $100US which is pretty good. I couldn't find the same card on eBay India or the Japan.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Using SMU 6612 to measure PXI-6528 pulsewidth channel - channel is not available.

  Hi all

  I use SMU 6612 card counter to measure the pulse width of the signals to PXI 6528 DIO card. These two cards are in the same chassis PXI (NI-SMU-1065). I could measure the pulse widths using the example LabVIEW 2013 Counter - pulse width of reading and (over) frequency example of .vi. However not all channels of the PXI-6528 map appear in the drop-down list of channels on the pulse width can be measured. Try to connect any other channel that those which are available in the drop-down list returns the error. On the PXI card port 6528 0,1 and 2 are entered ports and port 3-5 are output ports. I can measure the pulse on port 0, 3 width and line 0 port 1 and 4.

  Can someone explain to me why don't see port 1 or port 2 channels in the drop-down list or force the VI to measure the width of pulse on these channels?

  I can plug PXI-6528 external input channels SMU 6612 counter input channels and measure the pulse width, but if possible I'd like to avoid the external wiring between the 2 cards.

  Probably not.  Unless the routing plan is in fact reversed as it seems a bit sorta that.  As stated on my system, you can route * of * a port of entry * to * RTSI, or you can route * of * RTSI * to * one output port.  This does not make much sense to me, but that's what I see:

  

  If the routing card * is * reversed, your only likely workaround without physical wire would be to generate impulses in question of port 3.  It's pretty clear that 1,2,4,5-tetrachlorobenzene ports have no ability to interact with the bus timing, physical wiring would be the only option.

  -Kevin P

• PXI-1033 not detected until the pc is rebooted

  We have a chassis NI PXI-1033 with a PXI-5114 and PXI-4072-PXI-6221, fist, that he had failed to recognize and install drivers for motherboards. The search in the knowledge base, I tried workaround by disabling the PCIe mode ' bcdedit/set pciexpress forcedisable' command and rebooted the pc. Then the system recognized and installed the drivers for all the hardware.

  Disabled the PXI system at the end of the day. The next day, after activating the system, he did not recognize the hardware, returned changes to aid 'bcdedit/set pciexpress by default', then restarted the pc. Once again the material have been recognized.

  I tried to change the configuration on the PC BIOS, without success. The PC is an ACP-4000 of Advantech. We need to restart PC after a cold start so he could recognize the hardware and load drivers.

  Is this normal?

  Concerning

  The PC is under Windows 7 Pro. I searched on google for similar problems, where I found one where someone said that the culprit is that the chipset of the motherboard not give not the PCIe card delay what he needs on a start cold in order to be recognized. A reboot gives the time required and the card works.

• Delay time 4070 PXI DMM

  Hello

  I use a PXI-4070 DMM and DotNet "SoftwareTriggeredMultipointAcquisition" example

  I want to trigger the DMM4070 with the AuxTrig entry to the front of the instrument.

  This works very well, but how can I change the time out the of triigger?

  It is now on 2000msec. I want to 10000msec.

  When I us the example and do not trigger in the 2000msec I get error message saying:

  ModularInstruments.NIDmm: The operation did not complete in time maximum allowed. Timeout: 2000mS.
  Error code:-1074126845

  Thanks in advance

  Wissam

  Hello JaredRo

  I can set the time-out period now.

  Problem solved. Thank you Manny

  With greetings

  Wissam

• PXI SFP 5105 configured Vs Acquisition VI

  Hello

  I recently started to use the NI PXI-5105 cards, I need to capture (noise level<20KHz) on="" top="" of="" my="" dc="" signal,="" i="" used="" software="" front="" panel="" to="" capture rising="" edge="" of="" an="" analog="" signal i="" was="" able="" to="" capture="" signal="" when="" it="" meets="" my="" trigger="" requirements="" same="" as="" configured="" acguisition="" example="" vi="" also="" vi="" recommended="" input="" signal freq=""  ="" is="" 100khz,="" what="" changes="" i="" need="" to="" do="" in="" order="" to="" make="" this="" vi="" to="" trigger="" when="" the="" noise="" level="" on="" my="" dc="" signal="" exceeds="" certain="" point="" can="" anyone="" please="" help="" me="" with="" this="">

  Thanks in advance!

  Hey djo.

  If I understand your description, the best sounds of relaxation as it can be a trigger of hysteresis with coupling AC trigger in order to eliminate the effects of your DC signal. You will then be able to adjust the amplitude of the noise that you are looking for as the level to which you want to trigger off. You can find information about the options available with the help of scanners trigger high speed OR under Fundamentals > trigger.

• While with PXI-5122 digitizer loop counter

  Hello world

  I am a beginner of products NOR. Currently I use the PXI-5122, 2014 Labview for the ultrasonic signals. I have a problem when you count the number of signals using an external trigger (by a function generator) source. When I trigger the digitizer under 50 Hz, the meter is working properly (a single trigger = a signal). With a frequency greater than 50 Hz of trigger, the meter is malfunctioning. For example, with the shutter to 50 Hz and 500 number of signals, the counter takes 10s to get data. But, with the trigger of 100 Hz and 500 number of signals, the acquisition time was always around 10 s.
  You can see the code in the file attachment.

  Please let me know if you have any suggestions or recommendations for my situation, I would appriciate that.

  Thanks in advance!
  Best regards
  You

  WorldALoneMe,

  Looking at your code, you're software re - trigger your device.  With your Setup, you configure the digitizer to hold a single record acquisition in your "A - Scan.vi".  This VI opens the resource OR-SCOPE, configure, captures, returns the data, then closes the resource OR-SCOPE.  It then does this for each unique A-Scan that you do and would be the reason that b Scan.vi takes so long.  It appears then that fewer than 50 Hz, this reset any software and reconfiguration and the acquisition can occur without missing a trigger, but more than that, your triggers occur faster it takes to do these things.

  What you need to do set up the digitizer to a multi-record acquisition.  This is done using the 'niSCope configure horizontal timing.vi' and wiring in a number higher than '1' in the entry "number of records".  "You can find an example of how to perform a multi-record acquisition if you open the Finder of example OR > material input and output > Modular Instruments > NOR-SCOPE > Getting Started > niScope EX Multi Record.vi.

  In this example, the digitizer is only once configured, and it returns all the documents requested at the same time.  For your application, each record would be a simple Scan of A, and then if you configure 500 files, your B-Scan would be 500 wide.  This time allows the material to rearm between triggers that is much faster to do it in software.

  For a verification of more complex example out (in the finder of the example) "niScope EX Multi record go get more available Memory.vi"

  Kind regards

  Nathan P.