QoS in WLC 2504 for Skype and Lync
Hi all...
My clients said that the quality of the videocalls are poor. What can I to improve this.
I have little idea... Please help me...
Yes, enable QoS on wireless is much more of a QoS profile on a WLAN configuration. Please understand these guidelines QoS to design & develop your network.
http://www.Cisco.com/c/en/us/TD/docs/solutions/enterprise/mobility/emob73dg/emob73/ch5_QoS.html
Once implemented, you must check-to-end QoS is preserve, so it's QoS config/check on your cable as well.
You can check out some of my blog posts related to this topic. It will help you better understand what it implies the QoS configuration
http://mrncciew.com/2012/11/28/understanding-wireless-QoS-part-1/
HTH
Rasika
Pls note all useful responses *.
Tags: Cisco Wireless
Similar Questions
-
I can't use the microphone in my headset for Skype and recording programs
Hello...
I can't use my microphone in my headset for Skype and recording programs.
Can someone pls help? I tried the camera on my phone, it works perfectly.
I use v8.00.03 (T) Edition Premiun.Post edited by: worldliner
Sorry mate but could you be more specific?
> I use v8.00.03 (T) Edition Premiun.
What does that mean? Toshiba BT stack or what?There is a new BT stack:
http://APS2.toshiba-tro.de/Bluetooth/?page=download-Toshiba
Its v8.00.12 -
Installed an update for Skype and lost all my contacts
I INSTALLED AN UPDATE FOR SKYPE... I UPDATED FROM REGULAR SKYPE TO SKYPE BETA AND LOST ALL MY CONTACTS... HOW TO RECOVER MY CONTACTS OF REGULAR SKYPE-TO-SKYPE BETA... THANK YOU WILLIAM EYERLY
Hello
Since your problem is with Skype, it would be preferable to join the Skype's Forum's Support for targeted assistance.
-
Someone in the community all managed to connect a controller wireless lan to a 300 SG? I know that the WLC 2504 needs to be connected to a switch L3, but also a gigabit ethernet port. I plan on upgrading the firmware of the SG300 to version 1.3.5.58. Since the 1st version seems to have some problems using L3 switching.
Thank you
-Bill
The biggest drawback for most people is the VLAN tagging. The switch in many ways is like a switch in IOS, but it is not simply a switch of IOS.
Just keep in mind that if you make a layer 3 VLAN (assigned IP address to the VLAN), if sure the default VLAN has first of all a static IP address then go to make interfaces VLAN additional.
config t
int vlan 1
IP address 192.168.1.254/24 or anything else you want.
Continue to add the IP address and VLAN
config t
database of VLAN
VLAN 100
int vlan 100
IP address x.x.x.x /xx
Then you can make the trunks, etc. for VLAN desired.
config t
int gi0/1
switchport trunk allowed vlan add 100<- this="" will="" make="" the="" port="" vlan="" 1="" untagged,="" vlan="" 100="">->
Most people transitioning to this switch get caught up on these 2 things for some reason most any.
If you need help to set up the switch, you can always call the HWC, they have 24 hour support (without contract) or you can always feel free to hit me up (free support too)
-Tom
Please mark replied messages useful -
Small business router for Skype QoS
Hello
I've heard of Cisco technology for recognition of Skype traffic long ago and now I need to prioritize traffic to Skype in my network.
These technologies work for the current version of Skype?
Are there any small routers Business suitable for my task?
Hello, Alexander.
800, 1900 and 2900 series routers are marketed to small and large businesses but are managed by our team of the company. Small businesses such as the RV series class devices are very different. Currently at present small business devices (for example, the RV series) don't support dynamic QoS for Skype.
It may be worth reviewing base IOS routers you mentioned. Find a local partner or if you are a check of partner with the help of the partner.
-
I need program for voice and video chat (yahoo.skype. &...) for HTC HD7
Hello
You can get in touch with Support for HTC HD7 to get more information on this.
-
How & where can I shoot video for Skype? and dvd
I don't know anything about this computer or how to find whatever it is how & where do I turn on the camcorder for Skype & dvd
Please make sure that your camera is installed first. Cameras are normally installed when you plug (or are already installed, if it is a portable camera integrated). To check if your camera is installed, go to control panel, search for "peripheral", then click "devices and printers". If your camera is not listed, click on 'Add devices and printers' then find your device in the list.
In Skype, you can check if your device works fine via the tools-> Options menu, then video settings. If everything is OK, you can click on "View my video" when you place a call, or start a new "video call".
-
WLC with ACS 5.1 (RADIUS) for management * AND * Network users
Hello
I have authentication RADIUS of installation for the users of the network AND management on my NM - WLC (5.2 ongoing execution) against ACS 5.1
My Question is:-
For users to log in to Admin, I need to come back "Service-Type = Administrative - User" in order to make it work.
Because the ACS sees all applications from the same device (WLC) for Admin and network users,
the way I am currently treats it is by creating a filter based on the user name
Thus, users that contain 'admin' in their ID, use a set of
Network access policy authorization, who has an authorization associated with the attributes RADIUS profile.
Normal users have a ' network access policy authorization different rule ", with a different profile.
While this DOES WORK fine, still me I was wondering if there is a better way to do it, rather than create a rule
based on the user name.
I could use GANYMEDE + for the management, but I don't think that ACS allows the same client AAA (WLC) to use both protocols.
Thank you
I think it's something very common for things to do
You may notice that ACS 5 comes preinstalled with a selection policy of service that differentiates them the Protocol-based queries and orders or service 'Access to the network by default' or "Default Device Admin" out of the box
If you want only to RAY can either disable or delete the rule for applications of GANYMEDE + or not choose GANYMEDE + in the definitions of the unit
-
Original title: lifecam 3000 and Skype does not?
Hello, I tried the two 5.5 beta and 5.3. When I try to use the webcam with Skype it blocks Skype and says "Skype has stopped working windows is checking for a solution." I have windows update connection bars 4/5 drivers and my computer ==> http://www.newegg.com/Product/Product.aspx?Item=N82E16883103361 help is appreciated, thanks
Hello, I had just fixed yesterday. I deleted the drivers and programs that accompanies it, it ends up being the lifecam software that comes with it interfering with Skype, thanks to all who help :)
-
Im sick of crooks of Skype and intended for the other sweet cat
I have no idea, why is it so hard to have the option "Block friend requests" in Skype? Like 2-3 spam friend requests, I do every week. Its boring xxxxxxx and really makes me go away from Skype and of course, I'll have to ask my friends to install new alternatives, so we can discuss without blocking spammers once a day or two!
Actually, the answer is B.S. Before Microstupid bought Skype profiles could be put in private and the crooks could not access the info. Also I've never had this problem of applications unsolicited contact before MS succeeding Skype.
-
Connect Skype and incoming calls to the PBX - account problem
Hello
I have Skype Connect enabled and linked to my PBX with a SIP profile.
Now, I need activate incoming calls from Skype to my PBX.
Therefore, I need to link a Skype business profile account, but he refuses because the account I want to connect is a 'personal account '.
-Can I convert this account to business account?
- Or maybe I can delete this account and reuse the same Skype name?
Currently, I have 2 accounts (the admin Manager, "msfsupply" and a different account 'msf.supply').
I can't activate one of them for incoming calls.
I would like to be able to use one of these Skype names for incoming calls from my Skype Connect.
Please tell us what is the best thing to do.
Thank you
Renaud
Haha...
I started first with the help of Skype.
They told me to contact microsoft, because it is a business problem.
I called Microsoft
They told me that it was not for them either and I should post a question here on answers.microsoft.com to get a technician on that.
Skype sale:
https://www.Skype.com/en/business/
We do not work for Microsoft.
We are mainly volunteers here, just like you, computer users who give free advice from other users in our own spare time.
So, all I can suggest is TechNet, if Skype and Microsoft won't help you:
https://social.technet.Microsoft.com/forums/Lync/en-us/home?Forum=sfbfr
Kind regards.
-
New authentication active directory on wlc 2504
Hello
There is problem with very often a new authentication for servers active directory. Every time only if:
-loose client wlan/wifi because of the wifi hole or low RSSI
-output of build for a while customer
-wlan loose customer due to problem with homelessness (slow, not perfect)
There is possibility to keep authenticated users? I had hope that options: sleep customer, max session timeout, max idle timeout
help, but they do not work for me :(
My access point (2702) are all in a group flexconnect. WLC 2504 (8.1.102.0). My security in WLAN config is:
Layer2: wpa + wpa2, PSK
Layer 3: web policy, authentication with LDAP servers + asleep on client
I always try to improve the radio covers n fast roaming (11 k, r, v) but if someone leaves the area wifi, to do authenticated which is a little annoying...
Thanks for any advice or an index
Peter
You want people who re - attach to your network for to re-authenticate. It's a good thing. We do not want people using the old credentials, or expose you to a security breach.
This behavior is by design - and good.
-
Cisco WLC 2504 internal DHCP does not work properly
Hi all
I m trials with a Cisco WLC 2504 and some APs of 1832. I set up a DHCP scope on the interface of the controller with 2
a large number of different configurations, but the DHCP protocol does not work and Don t Access Point to obtain an IP address. My first question: is it possible to do DHCP for Access Points or only for wireless clients?
These are my interfaces:
Interface of the PA-Manager:
My DHCP scope:
Advanced DHCP:
I forgot something? Is there anyone using DHCP for its access points?
Thank you!
Hello
On Cisco WLC internal DHCP, you can add the option 43 to say where APs must register. In this case, they will try to resolve the DNS CISCO-CAPWAP-CONTROLLER or CISCO-LWAPP entry.
Let me explain briefly how AP-Manager works on WLC:
- Boots of Access Point and sends a discovery request to the management interface of the controller using the intellectual property you configured as DHCP Option 43 (as described above, it can be resolved by the DNS entry)
- Controller, sends it a response discovered that contains the name of the system, addresses AP-Manager, the number of access points already connected to each interface AP-Manager and the overall capacity of the controller.
- Joints access point controller using the less loaded interface AP Manager.
With this, every AP Manager must have a good configured interface and be connected to a different port, no LAG.
I drop a post here sometimes there is which might help:
https://supportforums.Cisco.com/document/118311/configuring-multiple-AP-...
Thank you
PS: Please do not forget to rate and score as correct answer if this answered your question
-
WLC 2504 cannot access the GUI...
Hi all
I'm not sure what I did wrong, the 2504 itself has only 4 ports and no port management but I heard it's actually port 1 (even if there are no labels for this). That's what I've done so far to try to access the GUI:
in CLI mode, I have
(1) put AP managament address like 10.151.55.129 255.255.255.224.
(2) I have activated the adminmode on port 1, which I assume is management port and enabling admin mode is the same as "no shut" on switches I guess; Here is the command I entered:
(Cisco Controller) config > adminmode port 1 turn on
(3) enabled HTTPS/HTTP through commands:
(Cisco Controller) config > activate network secureweb
(Cisco Controller) config > activate network web-auth secureweb
(Cisco Controller) config > network webmode enable
(4) I then reset system and verify that the changes took place to help display the synthesis network, as shown below. I also activated mgmt via dynamic interface to see if it makes a difference:
RF-network name... TEST_WIFI
Web Mode.................................... Enable
Secure Web view... Enable
Secure Web Mode Cipher-Option high... Disable
Secure Web SSLv2 Cipher-Option Mode... Disable
Secure Web Mode RC4 Cipher preference... Disable
OCSP........................................ People with disabilities
Responder OCSP URL...
Secure Shell (ssh)... Enable
Telnet...................................... Disable
Transfer Ethernet multicast... Disable
Transfer of broadcast Ethernet... Disable
Multicast/Broadcast AP mode... Address multicast: 225.225.225.225
IGMP snooping... People with disabilities
IGMP timeout... 60 seconds
Interval between IGMP queries... 20 seconds
MLD snooping... People with disabilities
MLD timeout... 60 seconds
Interval between MLD queries... 20 seconds
Period of inactivity of the user... 300 seconds
ARP timeout... 300 seconds
Cisco AP by default Master... Disable
Join AP priority... Disable
Mgmt interface wireless... Disable
Mgmt Via dynamic Interface... Enable
Filter MAC bridge Config... Enable
Safety of bridge mode... EAP
Mesh full sector DFS... Enable
Relief of AP... Enable
Support CMCC Auth Web... People with disabilities
Web Auth redirect Ports... 80.1
Web Proxy Auth Redirect... Disable
Bypass-Web Auth Captive... Disable
Web secure Web Auth... Enable
Quick change SSID... People with disabilities
Discovery of the AP - IP NAT only... Activated
IP/MAC Addr binding Check... Activated
Status of CCX-lite... Disable
oeap-600-WLAN-dual... Disable
oeap-600 local-network... Enable
mDNS snooping... People with disabilities
mDNS interval between requests. 15 minutes
(5) I installed my PORTABLE NIC to be 10.151.55.20 255.255.255.224 and connected to port 1 on wlc 2504; but I can't ping 10.151.55.29 nor do I navigate to https://10.151.55.29/. The port appears upwards (the flashing green lights on port 1 and Portable NIC also Flash).
Any help would be appreciated
If your connection to your laptop direct to port 1, then you have untagged the management vlan. Now you have configured for vlan 10, you must set to vlan 0.
You will then be able to ping to the management interface and connect to it through the user interface.
Sent by Cisco Support technique iPhone App
-
WLC 2500 - multicast / airplay - and more
According to me, one of my biggest problem is that I don't really know the exact term and configuration that will multicast...
This is a small network, I have a basis of 3750 X - ip switch 15.2 (1) E, that is my 'core' so to speak, a few vlans with IP and routing (static) active.
I have a WLC 2504, version 7.4.100.0
with a couple of 1602 and one 2602 a/c.
The WLC is linked to a trunk, my management interface port to vlan 40, my two SSID is both on the vlan 7.
Everything works fine, except the airtime (which I think is something Hello).
If I used a standalone / P of all other brands, it works very well, being a pretty layer 2 bridge, I guess - but if I connect to a hosted WLC SSID, things don't work well.
I looked at the guide to
http://www.Cisco.com/en/us/products/HW/wireless/ps4570/products_tech_note09186a0080bb1d7c.shtml
(Multi-Multi, because it looks like my WLC can't stand United, not selectable in any case).
It does not say that I need a L3 multicast router - which seems odd if they are all on the same L2 segment (subnet)?
Anyway, I don't think my 3750 X a multicast routing function - I have a 3560, who has the option of multicast routing (well, ip multicast router command exists), but I'm not using this switch for purposes of IP routing - and I couldn't find anything about what the correct way of setting this up is - as a "routing to local multicast for Dummies" or something... everything I'm trying to do is allow AirPlay between devices on the same subnet...
the seacrhes and tried countless things, like activate wlc broadcasting, which I did, and it worked for a while then stopped...
has someone any direction on what I need / should I set it up to make it work properly?
(I use NO of HREAP)
for example, the topology is
3750 x (IP router)
|
| -static routed VLAN / access to ports - an A / P out of here
|
| -Safe for WLC2504
|
| -Trunk to 3560C - 2A / s P out of here
You have certainly not routers multicast to operate a system of L2 with the multicast.
1 enable multicast on the WLC (Controller-> activate multicast worldwide and you can enable IGMP snooping).
2. activate the multicast group for the APs (Controller-> General-> AP-> 239.1.1.1 multicast group or something of the same address). It comes to have APs with multicast clients join a multicast group and unload the base a little network.
That should do it.
If they don't try any multicast traffic generator (http://sourceforge.net/projects/mc-mint/) between a source and a destination.
Maybe you are looking for
-
Unable to connect my Qosmio without Virgin dongle
Hello I recently changed my ISP to the Virgin, but I am unable to connect to my laptop without the aid of a dongle that Virgin provided. Is there a way I can connect without it?
-
Why my spider solitaire has itself removed from my list of games
Why spider solitaire disappeared
-
Neosmart of VISTA recovery disk
Tried to use it to start Vista to allow me to join the office so I can either do a system restore or format and reinstall Vista. Have Acer Aspire M1100 which is formatted by the departure of John. Booted from the recovery disk, choose repair your com
-
DeskJet F2480 software to download for Mac 10.9
Hello! I try to install my F2480 printer on my macbook running 10.9.2 Mavericks. I had no problem with the macbook, recognizing the printer, but I don't have the original disk to install the software. I tried to download from the website, but I can
-
Hi all just make me this error with KernelBase.dll, what happens to my end of the application, is that I am using .NET Framework to determine if network connectivity is available, to raise an event from a dll underlying to notify the application when