Qosmio F30 - 112 - Windows XP does not recognize the HARD drive

Hello.

I have a Qosmio F30-112.
I tried to install the Windows XP Professional instead of the Media Center edition.
However, during the execution of the installer, my laptop does not recognize the hard drive. Therefore, the installation cannot continue.

I thought it might be a problem of corruption with my laptop and reinstalled Media Center Edition successfully.
But when I try to install XP Professional it always gives me the same error.

Suggestions for the configuration of the BIOS or solutions for why this is happening?

Thanks in advance.

Hello

Just a question:
You are looking for in this forum for other similar issues with regard to the installation of Win XP and lack HARD drive? I doubt

The fact is that your notebook has a SATA controller and you need a SATA (Intel Matrix Storage Manager) driver.

You should have a look here in this doc from Toshiba:
[How to integrate a SATA AHCI driver into a Windows XP installation CD | http://aps2.toshiba-tro.de/kb0/TSB85017Z0000R01.htm]

and should also search this forum for other threads

Good bye

Tags: Toshiba

Similar Questions

  • Recovering the Windows system does not recognize the hard drive

    Computer does not recognize the hard drive when booting.  Guard gives me 1782 disk error.  Then try to use the ROM installation thing and throw a disc hard test there is no option to test anywhere.  Computer was working fine this morning and then I stop when I turned it back on it was not properly start.

    I have a zt3000 running xp sp3

    someone please help me, thanks

    Hello

    Please reinsert the drive from the rear panel and check if the device detects the drive hard in case you have the same problem, then the hard drive is bad, you need to replace the hard drive and reinstall the operating system on the unit to return to its operating state.

  • Install Windows 8 does not recognize the system drive

    I built a new machine (chart below). Since this is a new machine and not an upgrade, I bought Win 8 Pro 64 bit OEM to do a clean install. The SSD is my system disk that Windows 8 will be installed. Four data drives are mirrored, two for the other two. Construction went perfectly. The BIOS recognizes all six disks: 1 SSD, 4 HDD, 1 DVD.

    Insert and boot the disk of Windows 8. Accept the EULA, enter the product key. Arriving at the page "Where do you want to install Windows?", only four hard disks are listed. The SSD (installation to go) is not found by Win 8. ??? I tried to change ports SATA, cables, power supply - no difference. For each new change of hardware, the BIOS still sees everything. This isn't a hardware problem.

    The question remains: why the installation of Windows 8 does not recognize the SSD drive. All five disks are on AHCI. I'm not in RAID.

    I spoke with crucial technical support of all (manufacturer of the SSD). They were also surprised that the drive does not appear in the list.

    Does anyone have a solution? I spent all the money on hardware, as well as the new version of Windows and I cannot install it.

    This is the real kick in the teeth: Microsoft won't support me. The OEM of Windows 8 version is the same as manufacturers, such as Dell or HP. Support told me I had the support of the manufacturer. HA! I am the manufacturer. Either that or upgrade from an earlier version of Windows. This means that any that a new construction machine will get ZERO assumption of Microsoft. All just great.

    Thank you in advance for any assistance.

    Windows 8 Pro 64-bit (full version) - OEM
    Intel Core i5 - 3570K
    Card mother GIGABYTE GA-Z77X-UD5H
    Crucial Ballistix 2 x 8 GB DDR3 1600
    Crucial M4 2.5 "128 GB SSD (system disk)
    WD Green WD30EZRX x 4 (data readers) 3 TB drive
    Rosewill Challenger-U3 ATX Mid Tower Case
    SeaSonic M12II 620W 620 Bronze PSU
    ASUS DVD writer

    The DSS must be LOW LEVEL FORMATE.

    Once, there may be no other [HDDs] not connected to the SATA ports.

    Install Windows 8 Pro now.

    [Edit] Can someone please mark this as answered? I can't because I posted the question. Thank you.

  • Windows 8 does not see the hard drive on the Satellite A200

    Windows 8 does not see the hard drive on the A200.
    How to install it?

    S strange Windows 8 should already contain the HARD drive controller driver to recognize the HARD drive during installation.
    The HARD drive is visible in the BIOS?

    Do you use the original disc from Microsoft of Windows 8?

  • Satellite A205-S4777 - XP does not recognize the HARD drive

    Hello!

    Recently I buyed a new satellite Toshiba A205-S4777 with Windows Vista home premium installed
    and I noticed too many errors in Windows Vista and the pc is very slow so I decided to downgrade to XP

    I want to directly install Windows XP but the installer does not recognize the hard drive or more exactly controllers!

    I nLite Sata drivers in Windows Xp Sp2, I bought on the microsoft.com site!

    Everything worked well.
    The Installer recognized fine hard and Setup finallased!

    But here's the problem when loading windows and try to pass on gorge yourself sort of blue screen one unreadable!

    And restarts and let, it does all day the same thing!

    I'm afraid that I have not nLite the right drivers.

    Is there anyone Heve downgraded this model?
    Thanx

    Hello

    Maybe you did not use good SATA driver?  :| Who knows
    The point is that there are two different versions of Intel Matrix Storage Manager supports different chipsets.
    I put t know what chipset is in charge of your laptop but you should check this and must also check the description of the Intel Storage Manager and check what chipsets are supported.

    In addition, you should have a look here in this doc from Toshiba:
    [How to integrate a SATA AHCI driver into a Windows XP installation CD | http://aps2.toshiba-tro.de/kb0/TSB85017Z0000R01.htm]

    Good bye

  • Dell Inspiron 531 s problem of power/does not recognize the hard drive

    My Office does not illuminate. I replaced the power supply. No, it powers on but does not recognize the hard drive. It gives an error as SATA 0 None SATA 1 no SATA 2 No. How do we know that the cables are properly connected. I feel like I'm very close to solving the problem but don't have a clue what that next step to follow

    The original PSU had 4 sets of cables and connectors.  The new power supply has 5 sets of son.

    aries7531

    From your post, I guess that the configuration of the system now recognizes the hard drive?

    If you do not have a floppy drive, then BIOS can find the player who isn't there, it returns this error.

    Make sure that the floppy drive [drive A] is disabled in the [BIOS] installation system, page 173, so that it is no longer looking for the disc and see if this stops the error message.

    If the hard drive is recognized in the configuration of the system, he now knows in windows "My computer" or in "disk management, [right click on 'My computer' and select 'Manage', then disk management]."

    Bev.

  • Tecra S3: Installation of Vista does not recognize the HARD drive

    I try to install Vista Ultimate on my Tecra S3, but installation does not recognize the HARD drive.

    I tried to find the driver for Vista for my computer, but not found RAID.
    Tried it with XP drivers, but no longer works.

    Do you have an idea where I can download Vista drivers for RAID?

    THX

    Hello

    Your suggestion is good. The Tecra S3 supports the RAID, and the RAID driver is required to install the OS on the HARD drive.
    On the European driver Toshiba page I found a RAID for XP driver.

    I put t know if this driver will run under Vista, but I recommend to test.
    The RAID XP 1.3.8.0 driver version can be downloaded from this site:
    http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=EU

    Please note; You can store the RAID driver on an external USB and Vista should recognize it!

    Good luck

  • Satellite A30 PSA30E - BIOS does not recognize the HARD drive

    Hi all
    I have a Satellite A30 (PSA30E) and I start the computer. When I enter the BIOS it does not recognize the hard drive.
    Does anyone no what I can do?
    Is it possible to restore the BIOS?

    Thank you

    Hello

    You replaced the HARD drive by a new one or the BIOS don't recognize the old HDD?

    Usually if the laptop is not able to start and that the BIOS does not see the old HDD then I guess that the HARD drive is faulty.
    If the BIOS doesn't recognize the inserted new HARD drive and then either you ve bought is not compatible, or the size of the HARD drive is just too big.

    Please provide more info. You see error messages?

  • Lost in car-Windows xp does not recognize the slave drive

    I do reinstall xp home, no problem when I did the system does not recognize the slave drive I have.  As far as I can tell that it's all hooked up correctly.  When I go into disk management it does not recognize the drive either.  All of the suggestions.

    Hi james.williams,

    1. How is the drive connected to the computer?
    2. What is the number of the brand and model of the player?

    I suggest that you check the jumper settings and make sure that the jumpers are correctly positioned.

    Make sure they are in the two master/slave jumper and not cable select.

  • NSLU2 does not recognize the hard drive

    Hello

    I have a NSLU2 on Win XP SP3.

    It does not recognize the USB drives, he wrote that 'drive not formatted '. It only recognizes the USB key as "disk2".

    Current firmware is V2.3R29.

    When I try to update the firmware, the "not enough disk space" message.

    I tried the same disc on a different NSLU2 and it worked fine.

    What can I do my NSLU2 reading displays the disc correctly?

    Thank you very much for your help!

    Markus

    It seems to be a firmware issue... The V2.3R29 firmware. is quite old. The latest firmware is Ver.2.3R63... Hard reset the NSLU2, power cycle it and then try to update the firmware. After upgrading the firmware, reset it again and reconfigure... Disconnect the HARD drive before upgrading.

  • I can't access my external hard drive with windows 7. How can I get my music out of her files? My pc with xp operating system can access it without problem. but my new pc with windows 7 does not see the hard drive.

    I bought a new pc to replace my old hp 14 months as the motherboard fried in. I bought a case of disk external hard to rocketfish to put the hard drive of my Windows 7 pc in. burned does not see the hard drive. my old pc with xp can access all the items on the external hard drive.

    Check that the drive appears in Device Manager.

    If so, go to disk management and assign a drive letter.

  • Replacing the hard drive T60 - Windows does not recognize the hard drive

    Hello all, new to the community of Lenovo. I have a T60, but also the latest Lenovo Edge. HD crashed on the T60 and it will boot is no longer. I just bought a 500 GB WD without doing a lot of research. When trying to install Windows 7 (I had already updated the T60) it will not recognize the new drive - Windows does not drive at all. Is there a way to get the Lenovo to recognize the WD drive? Thanks in advance for any help.

    Looks like you're doing something wrong, if the drive is a SATA it should work, install it and boot from your windows installation DVD and it will be the installation drive and shaped for you, or you can optionally set the partitions manually when you are prompted to do so. If you try to do something unusual such as transfer windows on the old drive then you will need to explain exactly what you did because I see no reason it should not work. Infact I did it several times myself.

  • Used to boot Windows - does not recognize the hard drive

    Hello. I had my computer laptop vostro dell for 5 years, and I've never had a problem. A few weeks ago, I was starting, and I got the blue screen of death. I had the same thing when I rebooted. I bought a SATA dock for recover my files, so I could format it and start from scratch. However, the dock does not detect my HARD drive, although I hear the disc running. I tried to connect a Dell Latitude docking station to transfer the files, but the Latitude does not recognize my HDD ether. Vostro runs XP Home Edition and Zorin OS, Latitude anime XP Pro. HHD in question is a 120 GB Western Digital Scorpio for drinking devices. Help, please.

    You boot from the disk and choose "Try without Unbuntu and change to your computer"?. Honestly, it looks that you have installed. In addition, using raid with Windows Xp support?

    If you have chosen to 'Try' Unbuntu I recommend now you run chkdsk /r from the recovery console. The problem is not with the hard drive probably, but with the file system.

    Download WIndows Xp Recovery Console from HERE. Save the file to your desktop. You will need to burn the iso image to a blank cd using the same way you did to the image ISO of Unbuntu ImgBurn. Although the instructions below refer to a Windows disk, the disk from the Recovery Console that you create will do the same.

    1. Insert the Windows XP CD in your CD-ROM drive and restart your computer. If you are prompted, select any options needed to start (boot) on the CD.
      
    2. when the text portion of Setup begins, follow the prompts. Select the repair or recovery option by pressing R.
      
    3. If you have a dual-boot or multiboot system, select the installation that you want to access from the Recovery Console.
      
    4. When you are prompted, type the administrator password. If you have not set a password for the account admin simply press on enter
      
    5. at the command prompt, type chkdsk/r > press ENTER. (Note: there is a space between the slash and the letter k).
      
    6. at the end of the output of scan type > press ENTER.
      
    7 restart your computer.

  • Windows 7 does not recognize external hard drive after the reboot

    I just bought a WD external hard drive.  I plugged in the USB port and automatically loaded everthing.  I even registered the product.  Then I was told that there was an update to the external hard drive.  I went ahead and put to day and when my computer restarted to him alone is no longer recognizes WD external hard drive.  I had another hard drive that I used where Windows 7 does not recognize it either?  Is it some sort of security setting, I need to adjust on Windows 7 64 bit?  Please notify.

    Check if the hard drive is assigned to a drive letter in disk management.

    Click Start, right click on computer

    Click on management of

    Expand disk management

    Select your external hard drive if its posted here

    Make a right click paths and change drive letter

    Restart your computer, open the computer in the start menu and see if it shows then.

    Releasing it's easy: with Windows | ActiveWin | Laptops | Microsoft MVP

  • Vista PC does not recognize the HARD drive?

    Hello

    Windows Vista does not find the Toshiba external HARD disk.

    I find it with Paragon "Backup and restore" and in the control panel - Device Manager - readers

    but the HARD drive is not visible in desktop - computer.

    What can I do?

    Thanks fpr response!

    Hilli

    This external HARD drive is what HARD drive model?
    Do you use it for the first time?

    Have you noticed similar problem using other external USB devices?

Maybe you are looking for