Qosmio F50 - 10Z - fan cycling on and outside, even when idle

Similar Questions

• Qosmio F50 - 10Z revolves around 80oc degress

  Hi guys,.

  Have a very little bit of trouble with my Qosmio F50 - 10Z, the GPU (9600M GT) revolves around 80 ^ o ^ c degrees when using, the system has been cleaned with air compress and is in perfect condition of the art, I use the laptop on a table computer as well to ensure air flow.

  Thank you very much.

  AFAIK Qosmio F50 is old enough laptop model and if you use every day on base maybe is time for cleaning professionals. Compress the air is OK but more of dust is just inside and cold air and cooling rack may be blocked by dust.

  I've seen repeatedly disassembled portable and it is raise what it looks like inside after two or three years of use. In my old notebook I found cat s hair.

  What is with cooling fan? It runs at maximum speed?

• Qosmio F50 - 10Z overheating - Cooler recommendations

  Hello

  My Qosmio F50 - 10Z Guard stops due to overheating. I think Toshiba then set up this kind of configuration would have kept this question in mind. in any case, I thought that the solution would be to get a notebook cooler, but the problem is that the Qosmio F50 fan on the far upper right side and most portable coolers have fans more near the Center. I would be grateful if someone could recommend a good portable cooler for this model (or any other solution to the problem of overheating).

  Thank you

  Rehan.

  Rehan salvation!

  I can understand you, but I have at this point, I must say that I have too many Qosmio F50. He models the F50-10B s and also has Core 2 Duo 2.26 GHz but it s quick model with GeForece 9700 M GTS (I know your model contains only 9600M).

  What can I say about this? Well, first of all, I love this laptop. I love the laptops with 15.4 screen so it s not not little and not wholesale. The design of the silver/black is absolutely nice with white lighting. Not the same boring design than on most other phones. All my games work well on this laptop.

  On the issue of cooling, Windows and Office, the laptop is very cool fan doesn t usually works. On my Qosmio laptop I m using two power modes:
  (1) profile of PowerSaver I use for Internet and office: here I defined the maximum processor at 75 State and as cooling method I put in battery. If I can put a lot of power and it s enough for Internet and office.
  (2) balanced: I use it for my games so I maximum cooling performance and the status of the maximum processor that I have set to 100%.

  Moreover, I clean my Qosmio laptop every 3-4 months using a jet of compressed air. This could blow out the dust from the cooling fans and so I don't have to disassemble the laptop. I think that's really good.
  Here, you can get more information about this topic: http://aps2.toshiba-tro.de/kb0/HTD7A01ZZ000AR01.htm

  If you have any other questions, please let me know! :)

  Good bye

• Qosmio F50 - 10Z Bios Update crashed - how a cmos reset?

  I have a Qosmio F50 - 10Z and prompted by toshiba I downloaded the Bios Update and started to install.
  My screen saver came and it crashed.

  Not turn off (even after pressing the power button for 15 seconds).
  The drums and then put back. Computer skills on but the screen is blank and will not boot to the top.

  Tried to take part to Flash the bios by removing battery cmos/rtc (whatever it's called) but cannot find the battery and got to the point where I wasn't ready to dismantle any more (nobody else never disassembled a?)

  Could not find information or diagram or picture where the battery has been on the net... manual really useless laptop)

  Found reviews records of crisis, but I don't know what that means.

  So, how to I reset the bios?

  Please help - you're my only hope.

  > So, now, I find the cmos/rtc battery (if it's rechargeable explains so why does not easily localized) removed, he persevered on in a more accessible place - always reset BIOS

  Removing battery RTC would not help reset you mate sorry to the ROM BIOS module but what you did was completely useless
  It seems that the ROM modules where the BIOS is stored, was not properly flashed or something went wrong during the flash procedure

  In case of bad you the mobo is unfortunate but I think that Flash module ROM once more with a disc of crisis could help solve this case
  But the fact is that flashing the ROM module with a disc of crisis can be done by a technician of Toshiba ASP.
  That's why I recommend contacting the guys in your country and ask for flashing ROM

• Screen not switch on the Qosmio F50 - 10Z

  Hello

  Recently, I received my laptop Toshiba Qosmio F50 - 10Z (yesterday), I am very pleased with. However I seem to have a problem with the screen does not reverse when you start the laptop in sleep or hibernation mode. I tried to change the output screen (Fn + F5) but it makes no difference, and the laptop screen is always off. I need to cut my machine (5 seconds by pressing the button / stop) and restart manually. Then, the screen lights up again.

  It doesn't seem to be drivers updated compared to those I already have / preinstalled.

  I hope someone can help solve my problem.

  Thank you

  The story is really strange for me also
  I'm 100% sure that Toshiba provides new laptops and if you bought a laptop with a few scratches then you should blame your laptop for the same problem dealer

  Maybe the dealer of the laptop used this camera for a show or similar

  Welcome them

• Qosmio F50 - 10Z with windows XP

  Hi all

  I just bought an a Qosmio F50 - 10Z to run a CAD program, which does not work with Vista, unfortunately. I would like to keep Vista and add windows XP in a Setup to dual boot with Vista BootPro.

  Everything seems simple so far, but I am a novice to what follows. Apparently, after some research, I learned to integrate a XP disc with the necessary drivers. I'm a bit of a loss as to what drivers to collect etc so I went to ask the advice of a COMPUTER technician and he said that unless the drivers are available on the toshiba site then it is not possible to install XP at all.

  Is this true?, or is there anything else we can do? The interest to buy the laptop was running the CAD program (which only works on XP).

  Any help is very appreciated.

  > I'm a bit of a loss as to what drivers to collect etc so I went to ask the advice of a COMPUTER technician and he said that unless the drivers are available on the Toshiba site then it is not possible to install XP at all.

  That's nonsense!
  Of course, you will be able to install Win XP but the point is that a lot of portable devices does not work with Win XP due to unavailable drivers or tools

  The XP drivers are not available on the Toshiba driver page, but you can find it on other sites.

  For example;
  Sounds and driver LAN can be downloaded from the Realtek page.
  WLAN driver Intel page or here:
  http://APS2.toshiba-tro.de/WLAN/

  Driver BT from here:
  http://APS2.toshiba-tro.de/Bluetooth/

  Touchpad driver can be used other mobile computer series

• Microphone does not work - Qosmio F50 - 10Z

  Hello

  I have a laptop Qosmio F50 - 10Z.
  For the past two weeks, the internal microphone of my laptop stopped working.
  Its working fine but suddenly stopped working. However when I plug headphones to the microphone and speaker slots pins, it works.

  But without plugging the headphones, it won't work.
  Its really annoying me.

  Advice and assistance is appreciated. Thank you!!

  Have you checked all the settings of the recording device?
  Click on the volume symbol in the taskbar with the right button of the mouse and choose devices to record option.

• Problem on the Qosmio F50 - 10Z card reader

  I had this problem for a while, he started with the original OS Vista 32-bit, so I decided to buy the cd to upgrade toshiba for windows 7, after the update level, everything worked fine, except for the card reader, regardless of how many times I have installed/uninstalled, installed the driver, it wouldn't work!

  So I used the recovery cd, not once BUT TWICE, and nothing helps I sent to repair.
  I received a message on a piece of paper telling me that it would work on the original operating system, I thought that they had something fixed.
  Then I used the recovery cd AGAIN and to my excitement thrown short to see any yellow explanation points I put a micro sd card (2 GB) that worked when I bought this laptop first and got no response.
  The biggest problem is that my warranty is now closed!, so basically, I've been HIT MORE, cause the memory card slot does NOT WORK and it wasn't a software problem!

  Any reccomendations?

  Hi karimtarek,

  Which driver version you are using on Vista and Windows 7? My Qosmio F50 is running Windows 7 and I m using the version of the driver on Toshiba page 1.00.29.02.
  You use the same version?

  In addition, it would be interesting to know if the SD card has worked once you have received the notebook service center back. Have you tested before or did you start installation recovery immediately?

  Have you tried different brands of SD cards? I always use the SanDisk Extreme cards because they did not no problem.
  In addition, you could try updating the BIOS. Maybe this works if you are using an older version

  Last but not least if it s does not always work and you think that it s a hardware malfunction, ask at the center of service again. If you speak a bit with technicians, maybe they can fix it as a gesture of goodwill.

  Good luck! :)

• Boot from the disk ESATA on the Qosmio F50 - 10Z

  Hello

  is it possible to boot from an external drive using the ESATA port?
  I have BIOS 1.60 installed but I don't see an option for ESATA?

  What a USB? Laptop is a Qosmio F50 - 10Z

  Thank you

  I think that it of not possible to start from eSATA. The BIOS should provide this type of functionality.
  I've never tried, but I think that's not possible.

  As far as I know, it must be possible to boot from a USB device.
  The BIOS does not support this then try it.

• On my laptop - HP Pavilion dv7, the audio led on the keboard remains orange when I turn on and outside. When on this subject that is supposed to be a white light showing that it is on. How can I fix it? It happened when I upgraded to Windows 7 from Vis

  On my laptop - HP Pavilion dv7, the audio led on the keboard remains orange when I turn on and outside.  When on this subject that is supposed to be a white light showing that it is on.  How can I fix it?  It happened when I upgraded to Windows 7 from Vista.  Help, please?

  Windows Update has nothing to do with the upgrade of Windows. Try posting in one of these specific forums Win7:

  http://social.answers.Microsoft.com/forums/en-us/w7install/threads

  http://social.answers.Microsoft.com/forums/en-us/w7performance/threads ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Qosmio F50 - 10Z - use of several screens

  Hello world

  I have a F50 - 10Z and various uses for a multi-screen configuration, not less of my work as a literature student.
  Have at least two monitors by hand is very useful for writing the essay, I use one screen for the source material and the other for OpenOffice. In my downtime, I still prefer a multi-screen for photo editing configuration and the very small handful of games that support multiple monitors. I have to put it back the following:

  Laptop screen, screen 15.4 "capable of 1280 x 800
  Two Proview MA - 982KC 19 "TFT capable of 1280 x 1024, the surplus of my old office
  A Samsung 40 "LE40A656 LCD HDTV capable of 1920 x 1080

  I already know that I can connect either one of the monitors or TV and create an extended desktop, which I am at the present time, by aligning the monitors correctly in the Windows settings, which works surprisingly well and blew up between the very easy monitors. Otherwise I also know that I can have a monitor and TV is connected at the same time, creating two larger workspaces, the laptop can provide. What I can't do, is create a tri - or quad-monitor Setup. I would like to be following Office configurations, I set out that they would physically be in the Windows settings:

  Laptop TFT TFT

  _ TV
  Laptop TFT TFT

  My main concern is the work area. Toshiba DynaDock seems the most sensible option. Its extra VGA port would allow me to launch the first setup (TFT, laptop, TFT)? I appreciate the DynaDock is unlikely to support multi-monitor games, and I therefore also examined the Matrox Triple Head digital 2 GB. Now that the DynaDock seems very affordable, even if only as a medium-term solution.

  Provide a port replicator specific Qosmio Toshiba? I note that they exist for the other beaches, but they do not seem to a port replicator Port Qosmio from what I see. If they did, the DVI and VGA ports on a Port Replicator would be usable at the same time, allowing your desktop quad-monitor?

  I would be very grateful for any help you can provide.

  Concerning
  CorporalG

  Hello

  I think that there is no need to write much. On your Qosmio, you can connect an external device. TV or external monitor. If you want to use more than you need of external device like Dynadock.

  So the answers to your questions:
  * Toshiba provide a port replicator specific Qosmio? *
  NO.

  *.. commandeer the DVI and VGA ports on a usable Port Replicator simultaneously, allowing your desktop quad-monitor? *
  Just for example: on the Toshiba port replicator, you can use a video output port. It is not possible to use two different video ports on the Port Replicator at the same time. The video signal can not be cut.

• Qosmio F50 - 10Z - after update BIOS lit buttons do not work

  TEMPRO alerted me on an update of the BIOS - bios - 20090415092322.zip - for 32-bit Vista, published April 15, 2009 for my F50 - 10Z.

  Since then, the enlightened "buttons" at the top of my keyboard no longer work - including, annoyingly, the key to turn the light off.

  Is that what I can do at this point? I tried a system restore but it did not affect the BIOS.

  I agree with Akuma. Now, you can try to set the BIOS to default settings and also reinstall the package of added value.
  This package also contains command buttons utility.

  Perhaps after having reinstalled it everything will work properly again.

  Please send us a feedback!

• Qosmio F50 - 10 k - multimedia keyboard and recovery disc creation

  Hello!

  I have a Qosmio F50 - 10 k.
  I want to create a recovery disk, but I accidentally delete the folder, I didn't knew that contains the files for the recovery CD/DVDs. Is it possible to download? Or should I go to the store where I brought the laptop and ask?

  Another thing... my keys multimedia aren t work... I have searched for it and I saw a threat on the incompatibility of vmware, but I already remove vmware and the problem persists... What can I do?

  Big names

  > I want to create a recovery disk, but I accidentally delete the folder
  It wasn't good buddy.
  If you deleted the folder in HARD drive recovery then you will not be able to create the recovery disk
  In this case, you will need to order it here:
  https://backupmedia.Toshiba.EU/landing.aspx

  Good bye

• Qosmio F50 - 10Z - how to set up the bar multimedia?

  Greetings, have a question... because after a long time, trying to make it work, I can not find the problem...

  On my laptop, I reinstall Windows Vista, download all the drivers for the Toshiba for Qosmio F50 driver page, for Vista... and even how to set up the multimedia bar? With Dolby, sound on / off, light power... He s doesn't work do not. Are there special software required? Or can I put it somewhere?

  Thanks for help

  Use this-> http://eu.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp?service=EU research of Value Added Package 1.1.19

• Wake up the Qosmio F50 - 10G system mode 'sleep' and boots account locked window

  Why when the laptop is put to sleep and left for a while, flashing light and stops when you press the power button / laptop will wake up showing the BIOS screen then boots in the window account locked?

  Why I get this is event viewer? Source ACPI
  The embedded controller (EC) data returned when none was requested.
  The BIOS may try to access the European Community without synchronization with the operating system.
  These data will be ignored. No further action is necessary; However, you should check with the manufacturer of your computer for an updated BIOS.

  When Windows 7 starts, the icons on the desktop, menu start and records are white then start then normal fill when seen once again, any reason why?

  I used Windows 7 drivers.

  Thank you

  Hey mate,

  I have too many Qosmio F50 and you can change the option if, after hibernate or stand-by the account should be locked or not. As far as I know that this can be changed in power management.

  About this window of Event Viewer, I never heard talk about this and my Qosmio F50 works fairly well with Windows 7. You have installed all the drivers for it? You have yellow exclamation marks in Device Manager?

  I also used Windows 7 drivers, but did you download from the Toshiba page? These drivers are pre-tested and normally should work pretty well.