Qosmio G30-102 not start after the SSD upgrade

I have 2 x 840 Pro 256 GB SSD to install in my machine which usually runs two drives independently.

I used the software to Clone of Samsun to clone my C drive which has XP on it.

The cloning was successful.

On the installation of the new SSD, it will be now does not start and keeps cycling to the F12 boot screen.

I tried all the options without result.
Any ideas?

Hello

I had a similar experience with an upgrade of the SSD.
I used exactly the same software and has been able to clone partitions of HARD drive to SSD drive and my cell phone did not start the system from the SSD system partition.

I figured out that the C: partition on the SSD was not marked as active.
How I solved this?

Well, I put the SSD in the 2.5 external USB enclosure. Then I booted the laptop using the old HDD. I connected the external SSD drive to the USB port.
Then I went to Windows disk management and could activate the C partition on the SSD drive.
Then I replaced the HARD drive with SSD and could boot. :)

Tags: Toshiba

Similar Questions

  • 2011 21 inch iMac won't start after the SSD upgrade

    Recently, I upgraded my hard drive for an SSD via a computer repair business in my neighborhood, I also upgraded the ram, but I don't think it's in the case. On a two weeks after the upgrade, my computer don't turn on more. I took it to the genius bar and they told me that the DSS had "failed." So of course, I took my computer to the computer repair company and they ran some tests, discovered that the hard disk does not (according to them, he only read this way because the apple store has run the test for a normal hard drive and not an SSD). I'm not super computer savvy, so I took their word for it.

    Now, however, it has been nearly a month and my computer refuses to activate once again. Previously, it has worked well, the fans were running at full blast - what I knew would be a problem (although the repairman told me that they 'fixed' this issue too). So the first time, I downloaded a program called SSD fan control and set the fans to run in silent mode. This second time around, I realized that it was probably a bad idea because it could lead to overheating, so I put manually the fan speed so that we could hear still run, but just not as loud.

    I tried the reset SMC, but no result. Right now, I unplugged everything including disconnect it from the power strip.

    Any other experience of power with a new SSD failure? Is there anything else I could try at home before contacting the computer again repair business? I would not be able to reach at least until tomorrow, and I'm really curious to know how they managed to get my computer back on the first time.

    Also, I've been out of my warranty period for about a year, so that's why I thought that I was not risking too much by exchanging the original for one SSD drive.

    First of all, the original in Middle 2011 iMac hard drive had a temperature sensor integrated in the drive.  More new or replacement of those who do not.

    Other World Computing sells an Apple certified temperature sensor that plugs into the SATA cable.

    https://eShop.MacSales.com/item/OWC/DIDIMACHDD11/

    I just put a 2 GB Western Digital Black in mine, with the sensor.

    I suggest all first, reinstall the OEM disc and see if it boots.

    Put the SSD in an external enclosure and see if it runs...

  • HP mini 110-3500 laptop: computer laptop HP mini 110-3500 fails to start after the SSD upgrade

    Hello
    I recently bought a ' crucial 250 gb 2.5 "SSD and 2 GB of RAM (also by crucial), to upgrade my laptop HP mini 110-3500, who has been extremely slow. But unfortunately, the laptop refused to start when turned on. What can I do? I am very worried.
    Enkay1

    You answered. That's what I thought. You have DDR3L-1600 low voltage 1.35 volts. Low voltage will operate at a higher voltage (1.5 volts), but it is not the ideal memory for older hardware. Need memory DDR3-1333 name specified for the HP laptop. You can confirm or refute my diagnosis by putting in the memory of the old and see if it boots.

    It's the part number you need:

    621567 001

    http://www.eBay.com/ITM/2GB-compat-to-621567-001-A3803335-A4100445-A4427375-/230655741975?PT=LH_DefaultDomain_0&hash=item35b4275017

    Is your memory has 8 black on the side blocks or just 4? You want 8. Also if you have Windows 7 Starter, you can not use 2 GB of RAM.

    If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

  • 2450 PE does not start after the memory upgrade attempt

    Hello

    I have a Dell PE 2450, which is an older system, but has been working well and has 4x256MB DIMM in there and the last BIOS A09.  I tried to replace the DIMM A slot with a stick of 512 MB, and at switching on, a message appears indicating the amount of system memory has changed, followed by messages of typical POST on versions of firmware, and "Two-processor 866 MHz...", but then the system just sits there.

    The subsequent reboot by pressing F2 is not get into Setup or F10 penetrates me in utility Mode despite repeated attempts to press F2 all few seconds, I put the original memory back deleted, hard drives, tried to start on a diskette, etc.. I've tried unplugging, etc as well.  NVRAM would somehow corrupted?  Is it possible to reset?

    Thank you

    Don


  • Firefox will not start after the upgrade to 27. Seen an error message during the upgrade process.

    Firefox will not start after the upgrade to 27. Seen an error message during the upgrade process, but do not remember.
    Tried running firefox.exe Pei but error message:

    XML parsing error: the undefined entity
    Location: chrome://mozapps/content/profile/profileSelection.xul
    Line 18, column 1:
    "< dialog < =" "^ =" "p =" "> < / dialogue >

    Running on Windows XP SP3. No problem whatsoever before moving to 27. Sending of Chrome that I can't open Firefox at all.

    Thank you, jschaer2000. In the meantime, he works. How long, we'll see ;-)

  • Two iMacs does not start after the 10.11.4 update.

    Two iMacs does not start after the 10.11.4 update.  Progress bar starts moving and then text appears on the black screen saying unexpected sigkill to launchd.  He then gets stuck in a loop trying to start.  Tried to reset the SMC and LANDAU.  Without success.  Started in recovery mode and ran disk utility.  Discs said OK.  Chose to reinstall OS X from the list of options in the recovery mode (assuming it would be 10.11.4).)  Installation is finished but still once does not start.  Reinstalled on 10.11.0 successfully from a USB key and downloaded the 10.11.4 combo updater.  Installation seems to work, but once again, the macs will not start.  Same 'unexpected launchd sigkill' error.  A mac is now back working properly with 10.11.3 the other will be shortly.  Is there a problem with the accession?  Our COMPUTER support use Munki to get updates from one day to the next.  Fortunately, we were able to stop it before the other 20 or if Mac had the same problem.

    More information: two bricks iMacs were late 2013 models.  A 21 "and a 27.  We have just updated a test iMac which was a late model 2012 using the 10.11.4 combo updater.

  • ITunes does not start after the installation of Windows 10

    ITunes does not start after the installation of Windows 10, 1511 version (OS Build 10586.164). ITunes version 12.3.2.35, 6 GB RAM, Intel i3 @3.3 GHz. Itunes and Ipodserver module will run by Manager jobs, but Itunes does not open. iTunes starts in SafeMode as explained in the link below (hold SHIFT and control on your keyboard while you open iTunes).

    Fix unexpectedly closes or problems of launch in iTunes for Windows - Apple Support

    Solution, according to this link, is:

    If the problem does not occur in Mode safe, remove any third party plug-ins iTunes: solving problems with third party plug-ins - Support Apple iTunes but the link has been archived, and I can't find any plug-ins installed iTunes. Any other ideas?

    For general advice, see troubleshooting problems with iTunes for Windows updates.

    The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

    Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

    More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

    Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

    TT2

  • Computer does not start after the screen of the bios, Compaq Presario SR1023WM

    Ok. Trying to fix a friend's computer and seem to have met a strange barrier.

    Problem: The computer does not start after the bios screen.

    Details: When you turn on the computer, the compaq logo with intel inside is and has the < F1 Setup > and < F10 System Recovery > options listed as well.  And that's it as far as the computer becomes.  After that the computer just locked up, no work of buttons on the keyboard lights keyboard ect ect.  I tried the puree on the F1 key, as soon as I turn on the computer and I can handle so he can say * entering setup * but it freezes again after this point.  I already tried to eliminate the possible sources of the problem, removed all expansion cards, HDD and Dvd Rom module only disconnected, only memory (256 MB ddr 2700), power, vga and keyboard connected.  Ive also used the jumper on the motherboard to clear the cmos, hoping that would solve the problem without success.  I tried using a different memory stick and different memory as well...  Tried to use both a ps2 and a usb keyboard... Ive even tried pulling the rider for the protection of the bios password (even if she did not have a password on it, just try everything I can think of).

    The installed bios version is 3.1, and that's all that I know on the computer at this point, except that the website tells me to him.

    http://h10025.www1.HP.com/ewfrf/wc/product?product=411354 & LC = on & CC = US & DLC = in & Submit.y = 5 & Submit.x = 3 & lang = to & CC = US <-link to the Web page for the model #.

    I'm basically at a loss on this one, so if someone feels scroll line-by-line of their brains on this one, I'd be very happy.

    I have a pretty strong understanding of computer repair, so feel free to give me something to try.

    If you need more information out of me, let me know as well.

    Try to clear the CMOS again but this time remove CMOS battery and hold the power button on a few seconds. Replace the battery, then try to start back to the top.

    At the back of the pc is the condition of the PSU led green or flashing?

  • Z600: computer does not start after the installation of the 5 TB SATA drive

    My z600 refurbished does not start after the installation of a SATA of Toshiba 5 to disk.  After removing the drive, the computer starts.  I have my computer too old to handle a 5 TB drive, I something wrong or is the DOA drive?

    Thanks for the info.  I added the GPT to my search and discovered what had to be done in disk management.  Here is a page with step by step instructions and photos.  http://www.howtogeek.com/193669/whats-the-difference-between-GPT-and-MBR-when-partitioning-a-drive/

  • computer does not start after the Windows XP logo window

    Windows xp home edition
    service pack 2
    Dell inspiron 1501

    1. computer does not start after the Windows XP logo window
    2 works well in safe mode, even connect to the external monitor
    3. I reinstalled xp many times, problem stil exist.

    All the answers?

    Hi dhanushm,

    1. What happens after the Windows logo screen?
    2. You receive an error message?
    3. You have security software installed on the computer?
    4. Have you performed an installation clean Windows XP and even after that this problem exists?

    Method 1

    As the computer starts up fine in safe mode there is a possibility that some third-party programs installed on the computer is the origin of the problem.

    I suggest that you configure the computer in a clean boot state and check if it helps.

    To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

    See section to learn more about how to clean boot.

    How to configure Windows XP to start in a "clean boot" State

    http://support.Microsoft.com/kb/310353

    Reset the computer to start as usual

    When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

    1. Click Start , and then click run.
    2. Type msconfig , and then click OK.
      The System Configuration utility dialog box appears.
    3. Click the general tab, click Normal Startup - load all device drivers and services , and then click OK.
    4. When you are prompted, click restart to restart the computer.

    Method 2

    If fails it above step can refer to the article below and try the steps mentioned, check if it helps.

    After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

    http://support.Microsoft.com/kb/318027

  • XP does not start after the installation of avira. Blue screen: STOP: 0 x 00000024 (0 x 00190203, 0 x 87174270, 0xc0000102, 0x00000000)

    Original title: xp does not start after the installation of avira

    I have a HP Slimline s7410
    XP Home Edition SP3
    I had Norton free with Comcast, but since I have no more Comcast became Norton expired. So I uninstalled Norton and installed the free version of Avira, he scanned the computer and it was clean. I went to reboot and now it does not start.
    I have a cd/dvd drive of work.
    I don't have an XP bootable installation CD

    My system worked well until: I installed the free version of Avira

    Whenever I select one on the XP advanced options options menu start, it goes into a boot loop.
    I turn off the auto reboot system failure although it seems only work once, as the next time he's trying to start up it goes into the boot loop.

    Here's what my BSOD looks like:

    Disable or uninstall any anti-virus, disk defragmentation or backup utilities. Check the configuration of your hard drive and check the updated drivers. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

    Technical information:
    STOP: 0 X 00000024 (0 X 00190203, 0 X 87174270, 0XC0000102, 0X00000000)

    Any help is greatly appreciated! :)

    My first suggestion is to do a system restore at this time point.

    second suggestion is to keep your external drive connected to the pc at all times.  only detach when necessary.   of course, it would be better to install a second hard drive in the computer instead.   in any case, keep your personal files out of the system disk is a wise thing to do.   You can also download and store files for free on the Microsoft Skydrive site.

    third suggestion is to keep your system set upward through executing a check disk and Defrag at least once a month.   Basically, you can open the Explorer and right-click on the drive letter.  then select Properties, and on the Tools tab, you will have the opportunity to run the disk check.  then reboot and do a Defrag.   where this disk check fails, then you will need to run it to the drive via a bootable cd prompt.

    Interestingly, I don't know if the bootable cd that you made you allows to run the disk check.

    so my suggestion is to do a series of tests using your cd bootable your computer works.  see if you can actually run a chkdsk/r at the moment with them.    If Yes, then if your constant worries are having bad sectors on the hard disk, chkdsk/r will identify and mark so windows will jump on them.    in any case, see if your boot at the moment media can run a check disk at all, and let me know.

    fifth proposal is to install "microsoft security essentials" like your anti virus program.  even if you have run ubantu, it is not likely to have been an infected copy.   anti - are most critical virus for windows and not not so much for ubantu or linux is because windows is a system of world class operations.    the people who make the virus deliberately their engineer for the windows operating system.   If, however, ubantu and linux have been just as popular as Windows, virus engineers would make infections for the o.s. too.     Although they no doubt, attacks are more frequent for the windows os.

  • computer does not start after the installation of vista updates.

    computer does not start after the installation of vista updates. Startup Repair is also not working. event name: Startup Repair v2, prob GIS. 1: automatic failover, prob GIS 2: 6.0.6000.16386.6.0.6001.1800, prob 3:6, prob prob 5 and 6 GIS GIS sig, 4:720907: corrupt file, prob GIS 7: 3221226021, 8:3, prob GIS GIS prob 9: repair wrp, prob GIS 10; 2, 0 s version: 6.0.6000.2.0.0.256.1. In addition, none of these advanced recovery options seem to work.

    Hello

    Try the steps suggested by David Y post dated November 2, 2010 in the link given below and check if that helps.

    http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/a6071159-db22-4076-b5d8-31f446dbdf32

    Hope that information was useful

  • BlackBerry Z10 my BB Z10 does not start after the no shutdown reason cannot go home screan

    Dear expert

    pls help my problem

    My BB Z10 does not start after the no shutdown reason cannot go home screan

    How can I save my data and contact if I reload / back up the operating system how ever my phone cannot start and go home screan

    Thank you...

    Dear expert

    Thanks for your reply, but recognized link bb cant he showed a black berries knowledge so the transferdata button is impossible / cannot click. so I can't back up my files and data if I reloaded the OS. are there\s any idea/way of backing up my files if my phne was frozen?

    Thank you

  • Does not start after the upgrade to 1.5.

    Does not start after the upgrade to 1.5.  "EdgeAnimate.exe - not found entry Point? -Point procedure entry GetGestureInfo is not found in USER32.dll dynamic link library. »

    All ideas

    No problems in the past with edge since September 2012.

    =============

    Laptop HP Pavilion dv7-2185dx

    Dv7-2185dx product name

    #ABA product number NV023UA

    Microprocessor 2.00 Ghz Intel Centrino 2 Processor Intel Core 2 Quad Q9000 processor technology

    The microprocessor Cache L2 6 MB Cache memory

    6144 MB of memory

    Memory Max 8192MB

    Graphic ATI Mobility Radeon HD 4650 (M96)

    Video memory up to 2815 MB (1024 MB dedicated)

    500 GB (5400 RPM) hard drive

    Multimedia drive LightScribe SuperMulti 8 X DVD±R/RW with Support Double layer

    17.3 "diagonal HD + LED display high-definition HP BrightView Widescreen Display (1600 x 900)

    Fax/Modem high speed 56 k modem

    Network integrated 10/100/1000 Gigabit Ethernet LAN adapter

    Wireless Connectivity Intel WiFi Link 5100AGN

    The Altec Lansing SRS Premium Sound technology with subwoofer

    101 keyboard compatible with the keyboard keys full size numeric keypad with integrated

    Pointing device touch pad with On / Off button and dedicated vertical scroll up/down pad

    PC Card Slots 1 Slot ExpressCard/54 (also supports ExpressCard/34)

    External ports

    5-in-1 Integrated Digital Media Reader for cards Secure Digital, MultiMedia Card, Memory Stick, Memory Stick Pro, or xD Picture Card

    4 universal Serial Bus (USB) 2.0, 4th port shared with eSATA

    2 headphone

    1 microphone input

    HDMI

    1 VGA (15-pin)

    eSATA + USB 2.0

    1 RJ-11 (modem)

    1 RJ - 45 (LAN)

    expansion port for computer 1 cell 3

    1 IEEE 1394

    irewire (4 pin)

    1 consumer IR (remote receiver)

    Other devices HP Webcam with integrated digital microphone

    Dimensions 16.2 "(W) x 10.9" (D) x 1.37 "(min H) / 1.70" (maximum H)

    Weight lbs 7,74

    Housing for Kensington MicroSaver Security lock

    Turn on the password

    Accepts 3rd party locking safety devices

    Software

    Operating system:

    Genuine Windows Vista Home Premium 64-bit with Service Pack 1


    Hi, people.

    I was able to reproduce the problem here, so the good news is that you're not imagining things.  We are looking in the options right now for you guys, and I will contact you individually by private message to start again at the top.  This being said, please note that our techniques, Vista is an operating system that is not supported, and our team is not stable time on this platform.  We will do the best we can and we will keep you guys, update as to what status is.

    Thank you

    -Elaine

  • Windows 7 does not start after the C disk cloning

    I got a new SSD and hope to clone my drive C for the SSD, then start with the SSD. I cloned the C drive using the software that came with my SSD (NTI Echo iirc). Cloning is completed and the system stops. I started the PC and went to the start menu to change the boot for the SSD device. It wouldn't start up, gives me the following error: "cannot start Windows. A recent hardware or software change might be the cause. "Then it tells me to insert the Windows installation disc (that I have not since he's back in the States and I currently live in the Japan) to fix the computer. Boot from my original HDD with SSD unplugged gives me the status code "0xc000000e." Boot from the SSD with the original HHD unplugged gives me the status code "0xc0000225." Info for both was, "the boot selection failed because a required device is not accessible."

    I made a recovery disk using my laptop (which I am currently working on) and started via CD/DVD. The System Recovery Options appears and Windows 7 appears on the list, but the size of the partition is 0 and the location says '(unknown) '. I can't click Next or whatever it is because it's just loading all the time.

    I tried to go into the system recovery on the first screen (where you enter in the start menu, etc.) and by pressing F11 (System Recovery) doesn't do anything.

    My PC is a HP a6614f. I've updated the PSU with a 500W modular one and put in a dedicated GPU. Everything worked fine until I cloned the drive C on the SSD and now no player starts. The primary HHD is partitioned into two with Windows and programs installed on the C drive (personal files are on drive D partition). Drive C was 103 GB and my SSD has 119 GB of free space so I don't think it should be a matter of space.

    I am at the end of my tether here since I don't know why the hell my C drive cloning should affect the original drive. At least, I should be able to boot off the original drive, otherwise the SSD. really need my PC to work (with or without the SSD) so any help would be appreciated. Thank you.

    Has managed to solve my problem. All I needed was a Windows 7 installation disc for 'repair my computer.' I managed to download (legally) of Digital River and after that he did his thing, I was able to start my new SSD. Whoo Hoo!

Maybe you are looking for