Qosmio G30-155: video Capture does not work using s-video in port

Similar Questions

• Qosmio G30-195 - infrared receiver does not work after sleep

  Hi all!

  I have a problem on my laptop after Exchange of service of the motherboard.
  Once I booted Windows (Microsoft eHome transceiver) IR receiver works well in all programs, but when the system resumes from sleep mode, the IR receiver unloads from memory and can not find the search for material.

  If the remote control does not work until I have to restart Windows. Windows XP SP2 and Windows XP MCE behave the same. Before the exchange of motherboard I didn't you have a problem.

  What can I do with this?

  > What can I do with this?
  Contact service again and tell them the same thing. They need to know why this happen.

  By the way: you can use other USB devices connected after waking from sleep mode?

• Qosmio G30: Cam Sony MV does not work with port IEEE 1394

  Qosmio G30-117 does not support my Sony DCR-IP5E (a micro video camera) port ieee 1394. I tried to use pinnaccle studio 9 and video ulead studio 10, but I could not see my cam because of these programs.

  There is no problem if I install a new win xp media center edition (retail pack) and CDTOOLS drivers. But I want to use my setup of the Qosmio factory, I don't want to buy a new win xp media center edition.

  How can I solve this problem?

  Thank you all.

  Hello Amon

  I tested it with Qosmio G20 and my Sony camcorder using the same port.
  I tested it with Windows movie maker, WinDVD Creator, Adobe Premiere and Ulead Media studio Pro 8.

  You may believe, but each application was able to see my cam and I copied movies on the HARD drive, edited and created DVDs. I don't really know what is happening in your case, but when you connect your switch cam on game mode, and the cam must be recognized as new hardware and listed in Device Manager.

  When it works well to start the applications and check again.

• Qosmio G30 - 161 - recovery disk does not work

  Hello world

  I need help to understand what happened with my laptop G30-161

  The last time I tried to reinstall the product recovery things was wrong.
  The time where computer supposed to install windows then a blue display screen and stops the process and I get a black screen where there are three choices: start windows normally, or with the command prompt or networking safe mode.
  When I tried safe mode: I get a message that windows is not yet installed!

  When choose ok then the windows install see the screed for a few seconds and then the blue screen appears and disappears a few seconds and the windows on the screen appears as if the system will be installed, and after a few seconds, I get the same - back screen with the choice of the tree again.

  I tried several times to use the product recovery disc and enter in the same circle.

  great wishes to you all

  Hello

  > I have tried several times to use the product recovery disc and I enter the same circle.
  Are you sure you have booted from the recovery disk?
  This seems strange to me that you get the back same screen (start windows normally, or with the command prompt or networking safe mode) when you start drive recovery.
  These three options are displayed only if the laptop would be started from HARD drive.
  So please try to boot from the CD again.
  Insert the CD, turn on the unit, press F12, choose ODD as a source of start-up and follow the instructions on the screen.

  If this is not possible, then I would recommend the HARD drive.
  I recommend Drive Fitness Test. This software freeware s (google).

  Perhaps something went wrong with the HARD drive.

• Capture does not work

  I just got my new growth.  I'm very excited to this topic but already running into problems.

  He did all the Windows updates and I tried to install the update of the workplace grows, but he says that the carpet is not connected. Well, it is. Everything else works. Including the piano. The capture does not work.  I tried several times, recalibrated reestarted al such things.  All I get is a long delay, then a message with an error code: #A00904CD.

  What can I do?

  OK, today received the recovery media. 24 hours, it was fast!

  Do you have a reset and everything works now! (at least I could test this evening)  Apparently, I had all the wrong software in my germ.

  Thanks a lot for all the input.

  NORTH CAROLINA

• Rebel T5 does not work using the live view. Live view mode is enabled, but images are not captured.

  Rebel T5 is not capturing images when taking pictures in mode live view.  Live view mode is activated but update automatic and image capture does not work.  Any suggestions?

  troyantonik,

  What lens do you have and have you tried other lenses with your camera to see if they also not auto focus when you press the shutter button halfway?

  Just in case a parameter can be the cause, I recommend you to reset the unit to default settings.  Follow these steps:

  1. Press the MENU key.
  2. [#3 tools] tab.
  3. Select [clear settings].
  4. Select [delete all device settings].
  5. Click [OK].
  6. Select [clear all custom Func.].
  7. Click [OK].
  8. Exit the menu.

  If it is a time sensitive matter, additional support options are available to contact us.

• My WD 3 USB drive does not work in the 3 USB Ports on my Lenovo W530 lap. But work in the regular ports.

  My WD 3 USB drive does not work in the 3 USB Ports on my Lenovo W530 lap. But work in the regular ports. What can I do to fix this?

  Do not use windows update for drivers.

  Update your drivers Lenovo support and see if that helps

  If the lenovo is new, you can contact Lenovo support to asertain why usb3 ports apparently do not work

• Qosmio G10: The operating system does not work corectly

  Hello. My problem is that my windows xp does not work corectly, mousecursor, sounds, videos, games, programs, everything turns into a ' stop and go '. as the cpu slows all the 1-2 seconds. I reinstalled windows now 4 times and any document in the format hd´s.

  Don t know what to do...

  and a second question... maybe this could be the answer for the first ;-)

  in my hardware-registration of my system windows are two elements, for I can't find a driver.

  -PCI-Device
  -videocontroller fuer multimedia (German ;-))
  in English systems, maybe it's the multimedia "media control device" or "videocontroller" or something...

  does anyone know if I can get the drivers, because they´re not listed on the toshiba site. and my backup-disk system was stolen. (sounds strange... I know :-))

  OK, please give me some advice, if you have any ideas!

  THX a lot, patrick

  Hello Patrick

  First of all, it will be interesting to know if the unit is pre-installed by recovery media. The installation of Qosmio is quite complicated, and I recommend you use the restore CD.

  In this way it is not possible to give a precise answer because I don't know what kind of things is installed on your device. I guess in your case, some application (such as the virus scan) runs in the background and your HARD drive can be pointed out.

  If your recovery DVDs is stolen, you can order a partner of service authorized in your country.

  Good bye

• image capture does not work with the epson scanner after macOS sierra upgraded

  Image capture no longer works with epson scanner v800 after upgrade. I installed the new drivers from epson, and it still does not work. Just says: "waiting for scanner", but nothing ever happens.

  Drivers Epson macOS 10.12.x specific https://www.epson.com/cgi-bin/Store/support/supDetail.jsp?oid=256062 & infoType = Do wnloads & platform = OSF_M_X12 do not work?

• Qosmio X 70-A - keyboard does not work properly

  I have a Qosmio X 70-A-12N, newly purchased last September, 8.1 Windows 64-bit.

  After working properly (and lots!) for half a year, the keyboard started to stutter.

  If you type a paragraph or two, with say 250 words, each time and now, to say that every 10th or 20th Word (undpredictable), a key shot does not work. I tried another keyboard via USB: no problems, so it has to do with the built-in keyboard of Qosmio.

  It is not specific keys, and it is not the pressure with which you press the key.
  Any key can be be ignored from time to time.

  All drivers have been updated to the latest questions, the BIOS is 1.50.

  It seems that the problem is more important when working on the battery (not sure).

  Is it a software or a hardware problem? Should the keyboard be exchanged?

  My first thought was last updated from the BIOS, but according to the Toshiba download page you have latest version of the BIOS.
  You know that's not easy to say what the problem is here. I can't say with certainty if there is a problem with the keyboard, but maybe you should contact the nearest Toshiba service provider, explain the situation and ask for help.

  They know what needs to be done. at least, they have very good diagnostic tools and it is possible to detect the problem.

• Qosmio X 300 - 11W - TouchPad does not work in mode 'sleep'

  TouchPad does not work in mode 'sleep'. I can't wake up my computer using a touchpad. I downloaded and installed a driver for Windows 7 32 bit from a page of the Synaptics driver, but it did not help.

  Can you wake up your Qosmio using the power button / stop?
  You close the lid when the laptop enters the sliding mode?
  After you open the laptop lid should wake up. It work correctly?

• Qosmio G50 - Fingerprint log - it does not work

  I had to reinstall the software (like new) on my Qosmio G50 due to problems. (vista 32) Reinstall the fingerprint logo does not work and he keeps asking mr to register my fingerprints, when I try to do, he says can't open database specified. No idea how to get back on that.

  I tried to remove and don't reinstall, no luck
  I tried the fingerprints of delete on the settings in the event of corruption, it will not.
  Any help would be greatly appreciated.

  See you soon

  Here's a very interesting FAQ from Toshiba on how can you remove the fingerprints fingerprint reader?

  http://www.MyToshiba.com.au/support/items/FAQ/386

  Please post comments if you can remove fingerprints already recorded using this documentation

• Qosmio F60 - 11F - FN key does not work

  Hello

  the FN key in my laptop suddenly does not work and so I can't use with combination keys to control my laptop. I tried to make it work with the HWsetup, but there is nothing special for her in the keyboard tab

  I went to the download page for the driver to try reinstalling the driver, but I could not understand what driver should I download

  How can I make the FN key still works?

  My laptop is Qosmio F60 - 11F

  Please check if you can find the option restart Flash Cards in the start menu > all programs > Toshiba > utilities. If you have please use it to restart. If this will not help, try to reinstall Toshiba Value added Package. This package contains the utility of Flash Cards.

  Post comments.

• Qosmio X 875-Regza-link does not work

  REGZA-link does not work. When I connect to laptop to Toshiba TV HDMI cable, there is no icon regza-link on TV and I can't control the media player to the TV remote.

  At your Qosmio laptop factory settings?
  With other words do you use with preinstalled OS that you got with it?

• Qosmio X 875 - ECO mode does not work immediately after Win 8 upgrade

  I used the upgrade Toshiba Upgrade Wizard to Win 8. He succeeded well uninstall the incompatible software before the upgrade and install the new Toshiba and driver versions after the upgrade.

  I activated the ECO mode, and to my surprise, it does not work as before (in Windows 7):

  * Now, it works with the brightness to level 1 *... very dark. Before, ECO mode allowed me to go up to level 4 and was always considered in Eco mode...

  If I increase the brightness, the 'eco mode is disabled' message opens immediately.

  How to contact Toshiba to inform them of this problem and the other problem I found with the new BIOS?

  BTW, I am owner of a Qosmio X 875

  Post edited by: qosmitto

  > How to contact Toshiba to inform them of this problem and the other problem I found with the new BIOS?
  Contact your Toshiba authorized service provider in your country.

  Read this:
  + What is the TOSHIBA eco Utility? +
  http://APS2.toshiba-tro.de/KB0/FAQ2503AT0000R01.htm

  > It changes the brightness of the display of level 4, changes the brightness of the grey screen of level 1 (* 4),.
  _The * 4 means only on models with Windows7 installed _

  I guess that the previous configuration was only Win 7.

  8 win was made for mobile (use of the Tablet), the energy consumption of battery is also very important plant help to win 8. The consumption of the battery must be taken at the lowest level possible.
  So I guess that now help win 8 ECO medium mode and save the power max and long battery life time working at a max level.