Qosmio G30 - RAID may not reflect new 500 GB HARD drive

I have installed 2 new identical 500 GB hard in my Qosmio G30 with Windows XP.

The system works well, but the disc cannot be mirrored. Report of the Raid Controller is 'Normal Operation status.

This disk cannot be used for mirroring because it is outside the management of the RAID."

Who can tell me whether it is a disc error or is the drive of 500 GB to big for the toshiba with Windows XP raid controller?

> Can anyone tell me if it of a disc error, or is the drive of 500 GB to big for the toshiba with Windows XP raid controller?

Hmm. I m not very good, but it could be possible that the 500 GB HARD drive is too big for the mirroring of the mode.

But have you tried to change the mode in comforter Toshiba RAID you might find in Toshiba Assist-> Protect Fix & -> RAID Console

Check if you can switch to the mirroring.

By the way; RAID-1 is defined in the BIOS?
Usually, when you use RAID-1 configuration, the RAID is set to mirroring. In this case, the operating system recognizes the reduced ability to both hard drives (in your case, it is not important since you are using the two 500 GB HDD).

Check it!

Tags: Toshiba

Similar Questions

  • New 500 GB HARD drive is not recognized correctly

    What is happening, I replaced the drive HARD than Go 150 original after about 18 months, again, now a year later, that the drive seems to have died too, so I bought a new seagate 500 GB drive HARD for it, the BIOS said it s it, but vista CD dies just when it is trying to install, CD WXP can t see the drive at all, but I expected that when WXP is older , but Vista I expected to work.

    So here's the thing, I put the new HARD drive in my desktop PC and he found in the BIOS no worries, then I started the Vista CD and again no probs, Vista installed without worries, then I put the HARD drive in the lappy and once again he can t read it, so it s not a Vista thing , it seems that it s the lappy itself

    Is this a problem with the Toshiba BIOS, or is it a physical problem where the Toshiba is struggling in reading ANY player?

    It s driving me crazy.

    And what model of laptop do you have?

    Generally upgrade HARD drive should not be a problem. I assume that your laptop's HARD drive with SATA interface and I sure you bought the right of Mr. I've upgraded or because of the experiences on several laptops equipped new hard disks and all of them were still properly recognized and I was able to install original Toshiba Recovery (recovery DVD) on this subject image.

    Maybe you have an older model A200 and perhaps he has some compatibility issues with new hard disks. I will be 100% sure works perfectly with HARD drive up to 300 or 400 GB maybe.

    Do you use Toshiba Recovery for the Vista installation disc or original disc of Microsoft?

    BTW: WXP is unclear due to lack of driver SATA HARD drive.

  • Satellite A200-28R - new 500 GB HARD drive not recognized

    Hi all!

    The BIOS cannot recognize my new 500 GB SATA HARD drive. When I connect it to the laptop, BIOS says "No device" in the drive options. Tried jumper allows you to change the interface of disc HARD SATA-1, but without effect.
    How can I force the BIOS to recognize?

    Toshiba Satellite A200-28R
    BIOS version: Phoenix v.2.60 for Vista
    HARD drive: Seagate 500 GB 7200 RPM SATA

    BTW: my old 250 GB HDD works fine

    Hello

    Have you tried the drive in another computer?

    Maybe your new drive HARD isn t working properly or defective so use another rnotebook to test it or request a replacement HARD drive.

  • Vista Home Premium does not recognize a new 500 GB HARD drive.

    I installed a WD 500 GB drive in my Emachines computer.   He appears in "Device Manager" who says it works correctly, but the OS not the poster not in 'My Computer'.  Is there a limit on the size of the disk in Vista?

    Have you partitioned/formatted it?

    If not, right click on computer > manage > storage > disk management.

    Now right click on the graph for the reader, and select new simple volume. Allocate the amount of space you want to use it, i.e. all or certain of them so that you can have more than one partition on the disk. Now do a right click and format it. Repeat the new simple volume if you decided to make several partitions.

  • Most of Microsoft Windows Update Services, for example will not work after replacing my hard drive.

    * Original title: Unknown Publisher for most of the Microsoft Services such as the window update

    Recently, my Toshiba hard drive failed on my Satellite L500.  I replaced it with a new 500 GB hard drive.  And then used my Toshiba restore to out of the box, however, as stated in the subject, it shows most of the Microsoft Services do not work.  As suggested in another post, I ran MGADiag and here's what I copied.  What kind of help you can give is appreciated.

    Diagnostic report (1.9.0027.0):
    -----------------------------------------
    Validation of Windows data-->

    Validation code: 0
    Validation caching Code online: n/a, hr = 0xc004f012
    Windows product key: *-* - 4F8HK - M4P73-W8DQG
    The Windows Product Key hash: Xs1iQgVeo0C + sObJxS7eu + FuBPQ =
    Windows product ID: 00359-OEM-8992687-00057
    Windows product ID type: 2
    Windows license Type: OEM SLP
    The Windows OS version: 6.1.7600.2.00010300.0.0.003
    ID: {EC921169-98BC-407F-99C4-04D38DBA4400} (3)
    Admin: Yes
    TestCab: 0x0
    LegitcheckControl ActiveX: N/a, hr = 0 x 80070002
    Signed by: n/a, hr = 0 x 80070002
    Product name: Windows 7 Home Premium
    Architecture: 0 x 00000009
    Build lab: 7600.win7_rtm. 090713 1255
    TTS error:
    Validation of diagnosis:
    Resolution state: n/a

    Given Vista WgaER-->
    ThreatID (s): n/a, hr = 0 x 80070002
    Version: N/a, hr = 0 x 80070002

    Windows XP Notifications data-->
    Cached result: n/a, hr = 0 x 80070002
    File: No.
    Version: N/a, hr = 0 x 80070002
    WgaTray.exe signed by: n/a, hr = 0 x 80070002
    WgaLogon.dll signed by: n/a, hr = 0 x 80070002

    OGA Notifications data-->
    Cached result: n/a, hr = 0 x 80070002
    Version: N/a, hr = 0 x 80070002
    OGAExec.exe signed by: n/a, hr = 0 x 80070002
    OGAAddin.dll signed by: n/a, hr = 0 x 80070002

    OGA data-->
    Office status: 109 n/a
    OGA Version: N/a, 0 x 80070002
    Signed by: n/a, hr = 0 x 80070002
    Office Diagnostics: B4D0AA8B-604-645_025D1FF3-364-80041010_025D1FF3-229-80041010_025D1FF3-230-1_025D1FF3-517-80040154_025D1FF3-237-80040154_025D1FF3-238-2_025D1FF3-244-80070002_025D1FF3-258-3

    Data browser-->
    Proxy settings: N/A
    User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Win32)
    Default browser: C:\Program Files (x 86) \Mozilla Firefox\firefox.exe
    Download signed ActiveX controls: fast
    Download unsigned ActiveX controls: disabled
    Run ActiveX controls and plug-ins: allowed
    Initialize and script ActiveX controls not marked as safe: disabled
    Allow the Internet Explorer Webbrowser control scripts: disabled
    Active scripting: allowed
    Recognized ActiveX controls safe for scripting: allowed

    Analysis of file data-->
    [File mismatch: C:\windows\system32\wat\watadminsvc.exe[Hr = 0 x 80070003]
    [File mismatch: C:\windows\system32\wat\npwatweb.dll[Hr = 0 x 80070003]
    [File mismatch: C:\windows\system32\wat\watux.exe[Hr = 0 x 80070003]
    [File mismatch: C:\windows\system32\wat\watweb.dll[Hr = 0 x 80070003]
    [File mismatch: C:\windows\system32\sppobjs.dll[6.1.7600.16385], Hr = 0 x 80092003
    [File mismatch: C:\windows\system32\sppc.dll[6.1.7600.16385], Hr = 0x800b0100
    [File mismatch: C:\windows\system32\sppcext.dll[6.1.7600.16385], Hr = 0x800b0100
    [File mismatch: C:\windows\system32\sppwinob.dll[6.1.7600.16385], Hr = 0 x 80092003
    [File mismatch: C:\windows\system32\slc.dll[6.1.7600.16385], Hr = 0x800b0100
    [File mismatch: C:\windows\system32\slcext.dll[6.1.7600.16385], Hr = 0x800b0100
    [File mismatch: C:\windows\system32\sppuinotify.dll[6.1.7600.16385], Hr = 0 x 80092003
    [File mismatch: C:\windows\system32\slui.exe[6.1.7600.16385], Hr = 0 x 80092003
    [File mismatch: C:\windows\system32\sppcomapi.dll[6.1.7600.16385], Hr = 0x800b0100
    [File mismatch: C:\windows\system32\sppcommdlg.dll[6.1.7600.16385], Hr = 0x800b0100
    [File mismatch: C:\windows\system32\sppsvc.exe[6.1.7600.16385], Hr = 0 x 80092003
    [File mismatch: C:\windows\system32\drivers\spsys.sys[6.1.7127.0], Hr = 0 x 80092003
    [File mismatch: C:\windows\system32\drivers\spldr.sys[6.1.7127.0], Hr = 0 x 80092003
    [File mismatch: C:\windows\system32\systemcpl.dll[6.1.7600.16385], Hr = 0x800b0100
    [File mismatch: C:\windows\system32\user32.dll[6.1.7600.16385], Hr = 0x800b0100

    Other data-->
    Office details: {EC921169-98BC-407F-99C4-04D38DBA4400}1.9.0027.06.1.7600.2.00010300.0.0.003x 64*-*-*-*-W8DQG00359-OEM-8992687-000572S-1-5-21-3296362386-1532337117-3753913143TOSHIBASatellite L500TOSHIBA2.0020110121000000.000000 + 00090B83607018400FC10090409Time(GMT-05:00) Standard is03TOSCPLTOSCPL00109

    Content Spsys.log: 0 x 80070002

    License data-->
    The software licensing service version: 6.1.7600.16385

    Name: Windows 7 HomePremium edition
    Description: operating system Windows - Windows (r) 7, channel OEM_SLP
    Activation ID: d2c04e90-c3dd-4260-b0f3-f845f5d27d64
    ID of the application: 55c92734-d682-4d71-983e-d6ec3f16059f
    Extended PID: 00359-00178-926-800057-02-1033-7600.0000-3142009
    Installation ID: 021330453740668764980431685940600732000434410320980891
    Processor certificate URL: http://go.microsoft.com/fwlink/?LinkID=88338
    The machine certificate URL: http://go.microsoft.com/fwlink/?LinkID=88339
    Use license URL: http://go.microsoft.com/fwlink/?LinkID=88341
    Product key certificate URL: http://go.microsoft.com/fwlink/?LinkID=88340
    Partial product key: W8DQG
    License status: licensed
    Remaining Windows rearm count: 3
    Trust time: 31/05/2014-04:47:52

    Windows Activation Technologies-->
    HrOffline: 0x00000000
    HrOnline: n/a
    Beyond: 0 x 0000000000000000
    Event time stamp: n/a
    ActiveX: Not registered - 0 x 80040154
    The admin service: not registered - 0 x 80040154
    Output beyond bitmask:

    After reading through all the same problems here, I found a post that mentions a WD drive disc that I put in after the failure of my Toshiba HD.   I followed the link that took me to a page of HP but I installed the Intel Rapid Storage Technology driver (IRRT) via the provided download link and hop, from this moment, things seem to be fixed.

    http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c02219204&CC=NL&LC=en&DLC=en&product

  • I want to clone my original equipment existing 500 GB HARD drive to a new 1 TB HARD drive replacement. How?

    G ' Day,.

    I'm getting too big for my old 500 GB HARD drive, so I bought a new 1 TB HARD drive.

    Now I have all of the rescue disks that I made when I first got my laptop Compaq Presario CQ57-105TU . I could use them & fresh install all software & original OS, but then I have to start from scratch and re-install all the software I have installed, in addition to redo all adjustments & changes I made to the Windows 7 operating system since the first day - a year ago.

    Not really how I want to spend the next week or two around.

    I would like to clone the orig 500 GB HDD & all of its content to a new 1 TB of HARD drive.

    Sounds like where I want to go, but for 1 small question. I heard that if I just I'll have about 500 GB of space available new but I was also told that I will not be able to create new partitions of disk on the new HARD drive because of any existing partitions on the original HARD disk are created.

    1. is this true?

    2. in the case, where can I find a failsafe procedure to accomplish the clone, & then create 2 new partitions to cover the free space on the new drive.

    3. If so, is there a work around? If there is what is the procedure (plse give me cramps of brain with the jargon of techno... tnx)

    Some additional information that might be important.

    At the present time, my HARD drive has this configuration:

    Now that (Q) Local drive is diferent.  It shows 0 bytes available & 0 bytes used, & I don't have access to it.

    Computer of my wife... another laptop CQ62 model... also has the same drive,

    but hers is labeled as Microsoft Office 2010 Starter... as 0 bytes available & used - also no access, & as below, not showing is not in Dmgt.

    This drive does not appear in my Configuration of MANAGEMENT OF RECORDS : http://i.imgur.com/r4LPrDa.jpg

    Thanks for your time & consideration... Bobby

    Him early bird gets the worm, but the second mouse gets the cheese

    OK...'s done it!

    I used my CLONING HDD DOCKING STATION friends exactly like this, but he bought from a different seller 2 years ago.

    All I did was take my 500 GB drive original & placed in A slot (the front slot - Master) & I placed the new Toshiba 1 TB disk in slot B (the second slot behind Slot A... Middle - Slave). I turned the power on the box. I waited until readers spun & were ready, & I don't have a press the red button on the box...

    25% light started to blink & cloning began...

    About 40 minutes later 50% light began to Flash & the 25% brightness has remained stable.

    This means that 25%of the process has been done, & he went to 50%. .

    This sequence was continued until finally all the lights were on fixed (25% to 100%) which means that the clone was complete.

    I think it took about 2 hours and 15 minutes to clone completely.

    I closed the box power off. Then, I removed the two discs.

    I installed the new drive in the laptop carefully, & reinserted the battery, & I plugged power/charger/adapter sector of the laptop.

    Then, I ran into my fingers & press work / laptop computer shutdown.

    A few seconds my laptop has been as always to initialize.  I just had to check to make sure that I have installed the new drive... & Yes the one on the desk was the original, no doubt which means that my laptop startup disk was indeed the new drive I cloned just to.

    My laptop is started without fault!  without a hitch. Just as he always had.

    I used my computer management Administrative tool - disk management & made a simple volume for the 450 + GB of free space, affecting the next letter available player - in my car (F) case & I named it so.

    Everything worked perfectly, I can read & write on the new partition/volume. As I mentioned previously, I probably won't be able to start from scratch, but my drive (C), but it's fine for me.

    So, what have I learned?

    Well, first of all, my Compaq Presario CQ57-105TU can go to 1 TB of HARD drive without modification.

    Using the cloning method, I did no doubt saved full at least 1 weeks of resettlement work if I selected the new installation method using backup/rescue disks when the computer was first, I created started way back when.

    Outside the 2 + hours time, it took to clone the drive, 15 +/-minutes initially to remove & reinstall the drive, & the time it took to assign the new free space a drive letter (every 5-10 minutes) the procedure was clearly simple cut, I know could have been done differently, but not as simply as the method I chose.

    Pepe, thank you much for the time you spent researching my issues & responding to my message.

    I'm so glad all your fears & roadblocks have been made not, & in the end, it was possible to accomplish the task against our initial concerns - count in a very loose way with the greatest ease.

    Here are some pictures of the Station of Clone (the box) exactly like the one I used:

    Congratulations to all,

    Bobby, alias DreamRyderX

  • Desktop PC's processor HP 251 - a11, Windows 10, AMD quad core A6-6310 accelerated with 4 GB memory DDR3 system and 500 GB hard drive. I installed I tunes last version and cannot operate.  Error message says Hello not activated.  Tells me to

    Desktop PC's processor HP 251 - a11, Windows 10, AMD quad core A6-6310 accelerated with 4 GB memory DDR3 system and 500 GB hard drive. I installed I tunes last version and cannot operate.  Error message says Hello not activated.  Tells me to go to the Control Panel then administrative tools and allow to Hello.  I followed these instructions, but I can't activate Hello.  What did wrong and how I can activate the Hello?  My email is * any help is greatly appreciated

    < email published by host >

    For general advice, see troubleshooting problems with iTunes for Windows updates.

    The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

    Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

    More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

    Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

    TT2

  • Windows cannot be installed on this physical drive of this computer may not support the start-up this drive make sure that the drive controller is enabled in the computer's bios menu

    Hello world

    I know, there are several other threads on this topic, but I couldn't find a working solution. I currently have no OS on my DELL XPS 17 L702X. When I try to install from a USB stick bootable Windows 7 Home Premium x 64 I get this error message: windows cannot be installed on this physical drive of this computer may not support the start-up this drive make sure that the drive controller is enabled in the computer's bios menu.
    I've tried wiping HARD drive and reformat with GParted. I don't really know what I could do.

    I would be very grateful if you could help me

    Hello

    I suggest that you contact the manufacturer of the computer to change the BIOS settings and check if it is has updated the BIOS.

    Important: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

    Let us know the results. We will be happy to help you further.

  • Wizard BootCamp 6.0.1 running on El Capitan 10.11.5 installs single partition BootCamp on the disc Fusion consisting of 128 SSD part G SSD and 3 TB of HARD drive on an iMac (retina 5K, 27 inches, end of 2014), but not the part of the HARD drive?

    How is it assistant BootCamp 6.0.1 running on El Capitan 10.11.5 installs single partition BootCamp on the disc Fusion consisting of 128 SSD part G SSD and 3 TB of HARD drive on an iMac (retina 5K, 27 inches, end of 2014), but not the part of the HARD drive?

    This has two questions:

    1 capacity of SSDS faster for Fusion drive has been reduced. Therefore less effective for the reader of the merger. For example if I need to create a partition of 80G for my windows bootcamp partition, only 48 G will be left in the drive of the merger.

    2. ability of the bootcamp windows partition becomes very limited, cannot be greater than 120 G.

    3. even when I try to fuse out of the drive of fusion in the 128 G SSD and 3 TB of HARD disk, and then run the BootCamp assistant to create the bootcamp partition start from scratch to reinstall El Capitan only on the HARD drive (without drive Fusion), it won't let me do anything, it just shows an error that says something like "a person has created additional partitions on this drive please select. another disc. But there is nothing else to choose.

    Before my (5 K, 27 inches, end of 2014 retina) to El Capitan Yosemite, I was able to use the previous version of the wizard BootCamp 5.x to create the partition, bootcamp on the drive of the merger. And it will be divided in the fuser unit in two and insert the Bootcamp partition (with the size I chose, which can go up to 1 TB) between two partitions of MAC OSX.

    The disk partitions resulting from it, will be the partition MAC OS x on the SSD, the partition MAC OS x on the HARD drive partition #1, partition MAC OS x on the HARD drive partition #3.

    Then there is the BootCamp partition on the HARD drive partition #2.

    Is there a way to get what I need?

    That is what has been described in this notice of two canoes?

    Installation of Windows on a Boot Camp partition on a drive of TB Fusion 3

    n-on-a-3-TB-fusion-drive http://twocanoes.com/Winclone/support/installing-Windows-on-a-Boot-Camp-partitio

    Thank you.

    After having worked on those weeks, I realized that I need very painfully (by first going back to Yosemite and bootcamp 5 to escape all the limitations of El Capitan and BootCamp 6) I want to share here. Someone at - it other smarter solutions welcome.

    Note these steps and mentioned drivers only work for my version of iMAC, retina 5K late 2014. If you have other material, please search on the web to see which driver will work first. And all of these steps are destructive and assumed that you first take backup. It is only shared for interest only. Readers will have to bear your own risk.

    A. take backup

    1. take a backup completes my iMac Fusion Drive using Time Machine. Then restart with a Yosemite USB installation and select Terminal from the menu on the top bar.

    B. fuse out of the merger in two physical disks drive: SSD + HDD

    1. in the terminal, type the commands in show what the logical volume group ID and the ID of the logical Volume of the disc fusion)

    Cs diskutil list

    2. in the terminal, type commands for the fuse of the fuser unit and separate them to an SSD and a HARD drive.  Note: All data will be destroyed in the drive of the merger. There are many articles in this community on how this could be done,

    diskutil cs deleteVolume Logical Volume ID

    CS diskutil remove logical Volume Group ID

    This should finish within 30 minutes. If you have taken more time, this means that your reader of fusion has been altered somehow.

    I hit this issue too.  To use this command to remove the fusion drive hung up, and I need to do the hard to scramble a few sections of data in the hard disk partition table using the controls to tell the OSX this hard drive is a new without partitions:

    Cat >/dev/random /dev/disk0 (where/dev/disk0 is the SSD)

    and repeat for disk1/dev/disk1 which is the HARD drive in my case).

    This command will not return anything, but expect to press Ctrl-Z to end after 1 minute.

    2 create independent partitions (non-fusionend) for the installation of OSX.

    Borne Terminal output, and select disk utility, in disk utility, select the drive to HARD disk (and not on the partition), you will see the error message and you will be asked if you want to fix the fuser unit, click on ignore. Then wipe the HARD drive to create a single 'extended OSX journaled"named"HARD drive".

    3. Repeat step 2, and then erase the SSD drive to create a single 'extended OSX journaled"named"SSD ".

    C. install on the HARD disk as drive didier autonomous not fusion.

    1. go to Yosemite install screen and proceed with the installation of a clean copy of Yosemite to the iMAC. then connect you.

    D. use BootCamp Yosemite f5 to install windows.

    1. launch Yosemite bootcamp.

    2. check the two checkboxes for creating the USB drive to install windows 7 or a later version, and to download the windows supports the Apple software.  Do not click on the last box to install or remove windows pie creating real bootcamp partition again.

    3. it may take several hours to complete this function of your internet b/w and also performance of your USB drive.

    4. If you install Windows 7 (like me), then the downloaded drivers will not work for you, this will cause the issue of the device driver appleDSS.sys does not like this driver and others are too recent for windows 7 to use.  Also, your keyboard and mouse may not work even if you try to plug in a USB external keyboard or a mouse. You need to replace the drivers downloaded by others (the Boot Camp 5.1.5769 drivers that I find in this link: Software Support of Boot Camp 5.1.5769.) (Note: this driver is material specific only works for my iMAC model).  Once you have downloaded it, copy the two files in the root directory of the USB installation to replace the original ones. It's specific and material available for download somewhere on the Apple Site.

    -From the Finder, delete the $WinPE$ and the Boot Camp of the FLASH PLAYER files.

    -Expand the old drivers for Boot Camp 5.1.5769 (two records and another file) on your desktop.

    -Copy the $WinPE$ and records of Boot Camp in the FLASH PLAYER.

    5. open Boot Camp Assistant again and only select the third option, install Windows 7.

    It will show you the screen to select what installation disk, select HARD drive.

    Then drag the slide bar to select the size of the Bootcamp partition for windows you want, knowing that there is a restriction for windows installed using training camp on a MAC that the last byte of the BootCamp partition must reside in the first byte of the 2.2 T of each physical hard drive.

    For my case, I need only 500G for bootcamp and leaving behind 1.7 to for my MAC OSX partition immediately after the bootcamp partition and an another 0.8 T MAC OSX partition after him. 1.7 TB and the partition of MAC OS x 0.8 TB well exploited in the meantime bootcamp partition, will be merged into a fusion drive by Bootcamp. Thus, you will end up with total 2.5 TB of disk space in a logical drive - fuser.

    Go to this link for more details on this subject: n-on-a-3-tb-fusion-drive http://twocanoes.com/winclone/support/installing-windows-on-a-boot-camp-partitio

    6. continue the process to partition the hard drive, then it will restart automatically in windows installation mode, install windows.

    7. once the installation is complete, check that windows is functioning correctly.

    E. Si you want to upgrade to windows 10 Windows 7.

    1 if you plan to upgrade to windows 10, you'll find that the windows IE v.8 7 is no longer works and had many problems to load the page.  Then when you try to download the latest version of Internet Explorer, you get an error that you need at least windows 7 SP1 to support the last IE.  Life is too complicated, just download the google Chrome browser, then search for download windows 10 and then run the Microsoft valuation tool to upgrade.

    2 but before upgrade you, unplug all your MAC USB drives, otherwise, you will find that, after having spent an hour downloading the windows 10 software, the upgrade will fail with the error "/ dynamicupdate...» ». It is an inexplicable mistake that no one seems to understand why. There are articles with proven results that the removal of all USB drives before running the windows 10 upgrade tool will correct this problem.

    F. reinstall OSX El Capitan

    Once your target windows system (if windows 7, windows 8 or windows 10) works very well.  You can continue to create again your Fusion drive and reinstall OSX El Capitan.

    1. Insert the install of OSX Yosemite rear USB to the iMAC, and then select Restart Windows, or stop, and then turn the MAC once again.

    2. When you hear the ringing tone, press on and hold down the option key for 10 seconds. Then you release.

    3. on the selection screen, select start Yosemite OSX install drive.

    4. after starting, do not proceed to install OSX El Capitan again. But select Terminal from the menu bar.

    5. in the terminal, type the command 'diskutil list cs' and you should see nothing to prove that there are no existing fusion drive yet.

    6 type the 'diskutil list' command to list all disks and partitions.

    The SSD has two partitions, the/dev/disk0s1 of EFI (209 MB) partition and the other/dev/disk0s2 of OSX partition we created in step B above, called SSD around 121 G.

    The HARD drive has two partitions, the/dev/disk1s1 of EFI (209 MB) partition and the other/dev/disk1s2 of OSX partition we created in step B above, called SSD.

    G. delete the logical storage of nucleus on the HARD disk drive and it refuses with the DSS to form a merger with faster performance disc

    1. Insert the install of OSX El Capitan rear USB to the iMAC, and then select Restart Windows, or stop, and then turn the MAC once again.

    2. When you hear the ringing tone, press on and hold down the option key for 10 seconds. Then you release.

    3. on the selection screen, select start Yosemite OSX install drive.

    4. after starting, do not proceed to install OSX El Capitan again. But select Terminal from the menu bar.

    5. in the terminal, type orders for (to show what are the logical volume group ID and the ID of the logical Volume of the logical drive). You should see the logical volume to basic storage group created using two partitions on the hard drive, 1.7 TB and TB 0.8 created when we run the Yosemite Bootcamp to install windows.

    Cs diskutil list

    6. in the terminal, type commands to delete logical drives from basic storage.  Note: All data will be destroyed in the logical drive.

    diskutil cs deleteVolume Logical Volume ID

    CS diskutil remove logical Volume Group ID

    7. tap "diskutil list" command lists all the resulting partitions. You should see that the HARD drive has the following partitions.

    / dev/disk0 (internal, physical):

    #: NAME SIZE TYPE IDENTIFIER

    0: GUID_partition_scheme * GB 121,3 disk0

    1: disk0s1 EFI EFI 209.7 MB

    2: Apple_HFS GB SSD 121.0 disk0s2

    / dev/disk1 (internal, physical):

    #: NAME SIZE TYPE IDENTIFIER

    0: GUID_partition_scheme * 3.0 to disk1

    1: EFI EFI 209.7 MB disk1s1

    2: Apple_HFS 1.7 Untitled TB disk1s2

    3: disk1s3 Apple_Boot Recovery 650.0 MB HD

    4: Microsoft database BOOTCAMP 503.0 GB disk1s4

    5: Apple_HFS 801,4 Untitled GB disk1s5

    8 type the following commands to create the logical volumes group, named "myLVG" (or the name) of fuser using the usable for OSX to the SSD and HDD partitions.

    diskutil cs to create "myLVG" disk0s2 disk1s2 disk1s5

    Note: Mark the group id of logical volume shown in the results.

    In my case, I want to book the last partition as standalone partition disk1s5 no-fusionend, so I can use it to raise the back, or format it in FAT32 to allow the exchange of data between the MAC and boot camp.

    So, I do not understand this last partition in the drive of the merger. in my case, the command that I used is: diskutil cs to create "myLVG" disk0s2 disk1s2

    9 create logical volumes named "Macintosh HD" (or you call it) on the logical volume group we just created for the reader of the merger.

    diskutil createvolume logical volume group ID jhfs cs + 'Macintosh HD' 100%

    10 command "diskutil cs type list" to check the resulting fusion drive created.

    CoreStorage groups of logical volumes (1 found)

    |

    + Logical Volume - Group F53C7A25-C2F3-4997-91E9-2E6B6BAB2E0E

    =========================================================

    Name: LVG

    Status: online

    Dimensions: 1815635525632 B (1.8 to)

    Free space: 90112 B (90.1 KB)

    |

    +-Physical volume E176873C-7C80-4759-8110-BA7307E0C4B3

    |   ----------------------------------------------------

    |   Index: 0

    |   Disc: disk0s2

    |   Status: online

    |   Dimensions: 120988852224 B (121.0 GB)

    |

    +-Physical volume 6535AC3C-DCF8-453F-AD47-98905538386E

    |   ----------------------------------------------------

    |   Index: 1

    |   Disc: disk1s2

    |   Status: online

    |   Dimensions: 1694646673408 B (1.7 to)

    |

    +--> Logical volume family F3D15F87-FB84-4B43-B2F2-E9EACC7C42D9

    ----------------------------------------------------------

    Encryption type: no

    |

    +--> Logical volume 0D807F6E-FB7C-418F-AAF4-EF3EA3525D10

    ---------------------------------------------------

    Disc: disk2

    Status: online

    Size (Total): 1809780178944 B (1.8 to)

    Reversible: no

    Name: Macintosh HD

    Volume name: Macintosh HD

    Content indicator: Apple_HFS

    LVG Type: Fusion, sparse

    11 exit the terminal, go back to OSX El Capitan install screen and select the name of the fuser unit 'Macintosh HD' proceed to begin the installation of the os x for installation.

    12. There will be a step in the installation ask you if you want to configure as a new computer, or restore from a time machine previous backup. Make your own choices it accordingly.

    13 once OSX El Capitan has been installed and you have finished restoring the data and custom configurations, you can enter the application of preferences to check if you see the icon of the "Startup" disk", and if you choose Startup BootCamp in the next reboot, you should be able to boot up to Windows without pressing and holding the button option when reboot and choose to start windows manually. Also, in windows, you should be able to click on the bootcamp Control Panel and select for a startup to OSX on the next reboot.

    14. one thing to be aware, if you install bootcamp in this way, the boot camp and the GUI utility disk in OSX El Capitan will not be able to adjust your settings. This means, if you need to touch anything or to readjust the size of the partition, you will need to do it again in step A. Alternatively, some how to get started with installing Mac OSX Yosemite USB, then adjust the partitions using similar commands shown in this article or other articles in this community.

    15. yet once please take personal responsibility on damage if you follow the instructions in this article.

  • Install Windows 7 on a new 3 TB hard drive

    I'm trying to install Windows 7 on a new 3 TB hard drive.  During the installation, I get a screen that says no hard drives have been found.  Windows installs the boot files on the X startup disk but nothing else.  The motherboard is an Intel DZ68BC and the Bios is set to boot from the UEFI.  All of the suggestions.

    Hello Keith,

    Thanks for posting your question on the Microsoft community.

    Thank you for details on the issue.

    This problem can occur if the storage controller and chipset drivers are not updated or due to incorrect BIOS settings.

    I suggest you use the steps in this article and check if it helps.
    Reference:
    Windows 7 installation problem: hard drive not found
    http://Windows.Microsoft.com/is-is/Windows7/Windows-7-installation-problem-hard-drive-not-found

    Note: Changing the BIOS / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

    I hope this information helps.

    Please let us know if you need more help.

    Thank you

  • Satellite 2410 won't see the new 250 GB hard drive

    I am trying to upgrade the Toshiba 30 GB hard drive that came with the unit to a Western Digital Scorpio Blue 250 GB EIDE drive.
    I get out the swap the 30 GB to 250 GB put in a bootable XP SP3 CD version and nothing - no sign that power came to training.
    The CDROM is trying to write files on the hard disk, but nothing happens.

    Same thing happens when I try to use the pack of 3 CD of Toshiba or the Norton Ghost recovery CD.
    The computer does not see the drive. Put the old 30 GB drive and it starts right now.

    My BIOS settings show set up for EIDE and boot from the CDROM. What I'm missing?

    Hello

    It seems that the BIOS does not recognize the new HARD drive, I suppose that it s too big
    Satellite 2410 series is old and I guess that it will not support larger 120 GB HARD drive because of the 28-bit LBA s

    So try with the smallest HARD drive like 80 or 100 GB.

    Greetings

  • Satellite L300 - new info required hard drive

    I own a Satellite L300 and need to replace the hard drive. I am in Korea and went to the DEPOT, but they could not only replace the drive hard because they had only them in Korean, so I have to go elsewhere to get one in English (this is what I was told anyway) I don't know much about computers, I'm looking for help.

    When I bought my computer it came with Vista pre installed, so I don't have an installation disc or something like that. Because I get a new hard drive, I also will need to buy Vista and install it myself?

    Hello, my friend

    I'm a bit confused after reading your ad. Replacing the HARD drive is so simply and can be done by anyone and I do not understand how the service couldn t be able to do this. for this action, you need 10 minutes and can be done without manuals or service manuals.

    If you want to do this alone, please follow these steps:
    -Turn the laptop
    -Remove the battery
    -close to the battery you will see HDD cover fixed with two screws
    -remove the screws and the cover of the HARD drive
    -remove the block of HARD drive by pulling on the tab of the battery, following the direction of the arrows
    -Place the pack HARD drive on a flat surface (such as a desk) and remove the two screws flat head black with black head screws
    Please be careful with hard drives and apply pressure to the top or bottom of the unit.

    Vista operating system
    New Toshiba laptops are delivered without disc facilities but recovery image is saved on the HARD drive. When you start the laptop for the first time, you will see the recall of information you need to create this single disc using pre-installed Toshiba Toshiba Recovery Disk Creator. If you do not create and now the HARD drive is faulty, you have a problem. You must order the new Toshiba recovery media or you can use disks of Microsoft facilities to install Vista.

    If I forgot something please let me know.

  • Satellite A100 - 237 (PSAA9E) - can I improve it with a new 320 GB HARD drive?

    Hello!

    I want to switch the hard disk of my Satellite A100-237. It is equipped with 80 GB Fujitsu, 5200 rpm, SATA. I want to install a new one - 320 GB, 7200 rpm, SATA. But I don't know is it supported.

    I tried to find information about the possibilities for this upgrade, I could not find anything.

    Thank you in advance!

    > I want to upgrade the hard drive of my Satellite A100-237. It is equipped with 80 GB Fujitsu, 5200 rpm, SATA. I want to install a new one - 320 GB, 7200 rpm, SATA. But I don't know is it supported

    Don't worry, buddy... I don't see any serious reason why would be supported not the 320 GB SATA HARD drive.
    The SATA controller must handle the tough without major problems.

    It is important that you use a HARD SATA 2.5 ". The size and speed of the HARD drive should not affect compatibility.

    See you soon

  • Is it possible to change the 500 GB HARD drive with an SSD on my HP Pavilion MS228sc?

    I wonder if it is possible to change the 500 GB HARD drive with an SSD on my HP Pavilion MS228sc?

    If 'yes', I guess I have to go for a SATA SSD if there is. But I have to worry about other specs?

    If 'Yes'... what could be.

    I googled my question but no answers... so I ty Wizzards :-) Forum

    @Lord_Nikon

    In fact, this is not true. As long as he uses a large SSD enough it will be able to use the recovery media. I suggest using a SSD of 256 or 512 GB if budgeted for the upgrade...

    He doesn't have to make a Windows 7 installation USB drive and use the activation key license on the certificate of authenticity from the PC Windows to perform a cleanup to install.

    One of them should be on your PC. The Prodct key is what is needed for installation and activation online.

  • After the new installation of hard drive and a reinstall of Windows XP on I: function used Drive, Windows Update

    After the new installation of hard drive and a reinstallation of Windows XP I: Drive, Windows Update continually responds with: "Files required to use Windows Update are longer registered or installed on your computer" by clicking on the option to register or reinstall results by bike to the same error.

    Hi TedWie,

    Windows update no longer works for systems with SP2 or less. To check your systems service pack level, click on Start, run and typeWinver in the Run dialog box. If your system does not already have Windows XP SP3 installed, download and install XP SP3 from the link below. (Ignore warnings about professionals of computing and network facilities).

    Windows XP SP3.

    http://www.Microsoft.com/en-US/Download/details.aspx?ID=24

    Windows XP SP2. (According to THE level of SP)

    http://www.Microsoft.com/en-US/Download/details.aspx?ID=28

    Note:
    If your system has a Processor AMD, download and install before installation of the SP3 of XP, theUpgrade utility Microsoft for processors not intel

    http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?CC=UK&LC=en&softwareitem=PV-60484-2

    If you encounter problems installing XP SP3, you can refer to the procedure described in the link below to resolve an installation failure.

    How to troubleshoot a SP3 Installation fails.

    http://support.Microsoft.com/kb/950718

    Let us know if this solves the problem.

Maybe you are looking for

  • Satellite L855 - 14 H - green texture while playing games

    Hello!First of all, I want to apologize for my bad English skills, because I am from Latvia.Allright, enough small talk - so I bought the new computer L855 - 14H. It came without OS, so I installed Windows 7 Ultimate x 64. Everything was fine until I

  • To retrieve a different recovery Cd to a same HP2000 model HP2000.

    Two years ago, I bought two HP2000 329WM laptop for my two college students of age. Of course, neither a fact DVD recovery kits, and they have rarely bothered to save. My son's hard drive just crashed, then put in a new hard drive and a start to reco

  • Why my computor back to - sign - password on & more when I'm on the computor?

    every time that I get on my computor - after my registration w/Password - Although I'm working on computor it return backwards to the 'fishing in' all few seconds? He had to fix.

  • SBH50 and xperia compact z3 with lollipop 5.1.1

    Hello world. My SBH50 can not display notifications of my xperia z3 compact, because it is impossible to grant permission to the notifications on android lollipop 5.1.1 (SBH50 app is not indicated on the list). Is there a solution?

  • 3555

    I have a Dell with an Alps 3550 - touch pad that has the dreaded cursor jump around.  I have re-uploaded the driver of the Alps touchpad from the Dell Support website and it did not fix the problem.  Any way to set the sensitivity of the touchpad?