Qosmio G40 - black screen and does not start

Similar Questions

• Satellite A135 black screen and does not start

  I have a Satellite A135 with windows vista and I have not used in more than a year.
  I went to use it today and it turns on but the screen is blank. I can't even see not the bios.

  I tried the usual things, connect to a monitor, removed the chip of ram from the back and tried another one, I also tried power alternative only with no luck.

  All the ideas it might be.

  Thanks for the help

  Hello

  If the BIOS page does not appear, then it s a serious question.
  Seems that the motherboard is dead.

  In my opinion, a technician should check this section first, and perhaps you will need a new

  Motherboards are parties, then perhaps it s not an option for you

• Windows load with black screen and does not start after windows updates

  Original title: load windows normally screen will not continue

  I went to my computer tower and I chose to install updates when closing.  I went back later to re - turn on my computer and now it loads to the top of the black screen that gives you 5 options. safe mode, safe mode with networking safe mode command prompt, windows loads normally and finally to load windows from last known configuration that works.  Problem is that none of these options work.  they all return me to the same screen.  Help this laptop came preloaded with Win XP Media Center edition and I can't get back to work.  IM assuming I need a XP disk support center but I can't find them anywhere! HELP PLEASE SOMEONE!

  Hi Burton089,

  Your hypothesis is right. To resolve this problem, we need to repair your installation of Windows using the Windows XP disk. We recommend that you contact the manufacturer of the laptop to check if they have the Windows recovery disk.
  See perform a repair Installation
  

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Computer has a black screen and does not start. Vista of Aspire5535 Acer base

  As above.  Help please!

  Hello

  If when you start your Acer is no 'Acer' logo splash screen at all and nothing appears on the screen, which would indicate a hardware problem.

  If under warranty, contact Acer.

  If it is not under warranty, use a repair shop, local.

  See you soon.

• Computer has a black screen and does not show the normal startup logo and more

  The computer that I use usually works well, until the next day, the day that I used it, ruined everything. My computer shows not the Windows 7 logo normal at startup, but instead, a bar with green lines in movement like the ones you see in older versions (Windows Vista), but now only the bar and did no logo in it and after starting does not display. It shows a completely black screen, but it makes a noise like the sound when she welcomes you to Windows 7. I tried safe mode and disabled the NVIDIA GeForce GT 220 graphics card and the screen works, but he is stuck at 800 x 600. In addition, the start screen is always the bar. How can I fix it? (Tried updating the gpu but still displayed black screen)

  Hello Rafael,.

  Thanks for posting your question on the Microsoft community.

  We need more information about the issue so that we can help you better.

  What is the brand and model of your computer?

  Thank you for details on the issue.

  This problem may occur because of corrupted display driver.

  I suggest to start your computer in safe mode, uninstall the display driver, restart your computer in normal mode

  mode and update driver from the website of the manufacturer of the computer display.

  Please see this link:
  Why my screen is black when I start Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/why-is-my-screen-black-when-i-start-Windows-7

  Important notes:
  Serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  http://Windows.Microsoft.com/en-us/Windows/back-up-registry#1TC=Windows-7

  When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• Equium P300-19O - black screen and does not restart

  My Equium P300-19O had a blue screen of death after a few accidents occurred due to a broken Windows media player which 3 safe resets and then I get a blue screen of death.
  I restart the laptop, but now I have past the toshibia load up, but do not get further rather get a black screen with a dash flashing in the upper left corner.

  Please suggest anything that could help me get the laptop again.

  Hello

  Have you checked if you can boot into safe mode? You can try to start in safe mode if you go into the advanced boot menu by pressing F8 after you have switched on the laptop. Here you can choose.
  Maybe you can also try a system restore to a previous state.

  If it doesn t work it should boot from the recovery disk Toshiba and reinstalling Windows.

• Satellite P200D - black screen and does not just by running

  Hello everyone, I have a Toshiba Satellite P200D - 107 PSPBLE with configuration set-aside:

  Processor: Turion x 2 TL - 52 64-bit clocked at 1.6 Ghz
  Display: 17.3 inch
  Graphics card: Ati radeon x 1200
  RAM: 2 x 512 MB ram (1 GB total) which I upgraded to 1 x 2000 MB and 1 x 512 MB (for a total of 2.5 GB)
  OS: FACTORY CD WINDOWS VISTA HOME PREMIUM 32-BIT
  Power: Running on the direct power without the battery cable

  Although the pc is quite old sound fundamentally new barely there 1 year of normal use on it.

  PROBLEM:

  The screen goes black (no), even if the screen still has the backlight running, the laptop is still under tension, but its basically in a kind of deep hibernation with the fan running yet.
  The laptop screen turns off 5-10 minutes after windows loads, even if in idle, it also stops during installation of the operating system.
  I tried to run the music and the music stops when the screen goes black made all the hard disk activity which I believe indicates that it is not related to the video chip.

  TRIED SO FAR:

  1. open up the computer laptop and cleaned all dust processor, now CPU temp is 50 max, even for hard disk
  2. update the bios to the original to 1.70 - did not help
  3 connected external monitor also stops it the same time as the laptop screen indicating it is not not a screen issue
  4 reinstall OS several times
  5 tested memory with memtest64 - no error
  6. test the hard drive with hddregenerator - no error

  What I've noticed:

  If I leave just a 512 MB of ram in the laptop then the laptop stops not at all even in windows applications, tried to launch a game to remove video card and it works without problem for hours, but as soon as I add the stick of 2 GB or another origianal 512 stick it will go inside the black screen 5-10 min (or earlier) to get into windows.

  He never stops in dos mode (as in memtest, hddregen) even with 2.5 GB of ram.

  After that the screen goes black, if I stopped and then try to save, it it won't work at all, the screen stays black with the fan spinning and boot CD, I must absolutely disconect the power cord power and re - set before it starts again.

  Anyone has any ideas, I am experienced with the pc, but have never stumbled upon something so weird that I have just can't explain this problem that came straight from heaven.

  Toshiba to wake up, this forum is a total joke, you would think that you would be able to afford hiring a bunch of technicians to actually help people rather than rely on the users of the forum to do your work for your, you don't need to have a forum, if you don't have the staff to actually help people solve their problems.

• MacBook Pro glued on the gray screen and does not start. Help, please!

  Hello

  My 13 "MacBook Pro (mid-2009), running Snow leopard (10.6.8), has finally given up and won't start.

  I tried to boot into SafeMode several times, but the loading bar does not move and the laptop just completely stops.

  I also tried to boot in single user mode with the command fsck - fy, but this results in the following:

  disk 0 s 2: I / 0 error

  Invalid node structure

  (4,35296)

  * The Macintosh HD volume could not be completely checked.

  / dev/rdiskOs2 (hfs)

  You leave with signal 8

  I guess that means that there is something wrong with the hard disk and some corrupt files?

  My problem is that I have no time machine backups, so I would like to know if it is possible to do something to get to the top and running.

  That, I do not have an external drive with my main important files and photos on a failure, so is it possible to completely erase the computer so I can sell it at least?

  I really need help on what I've been driving myself crazy trying to figure it out!

  I'm not all techniques with regard to the material. I tried doing research and have seen things, which suggests that I should reinstall the OS X, this would imply in the disks provided with the laptop when the power?

  Any advice greatly appreciated!

  Boot from the DVD and run the check/repair disk utility and repair permissions until you get no errors.  Reformat the hard disk using Disk Utility/Erase Mac OS extended (journaled), then click on the Option button and select GUID. Then re-install the operating system.

  When you restart, use Setup Wizard to restore your data.

• Satellite L655D crashes on Windows startup screen and does not start

  Hi, I hope someone can help me.

  Portable Satellite L655D age of 18 months of my daughter began to hang on the black 'starting windows' screen, when it stays until it turns off after several minutes. I didn't spend this stage for several days, and the machine seems completely unusable.

  I then turn off by pressing the power button for a few seconds, I can then select F12 with the option to start in safe mode, but the laptop never makes it in safemode, it real just data on a screen black for a few seconds and then it crashes with the message "Please wait".

  Others that look, I'm not able to go beyond these screens.

  Any help would be appreciated.

  Thanks, Darren

  Hello

  Did you create a recovery disk?
  In this case, you could use this drive in order to reinstall windows on the laptop system.

  Another possibility is to drive HARD recovery. Press the power button, F8 and choose fix my computer. Now choose HARD drive recovery.

  I hope that you can do this

• Screen saver does not start on my Qosmio F20

  My Qosmio F20 screen saver does not start even after reaching the specified minutes 'wait '. I tried several ways to fix it, but to no avail. I really want the screen saver to appear.

  Hello

  Well, usually the common screensaver that are pre-installed on the operating system to work properly. I put t know what screensaver you use, but I guess that you have installed a 3rd party screensaver. In this case you should check these settings. For the most part a screensaver 3rd party has a parameters.

• my screen saver does not start. I select a screen saver, set the time, apply and nothing. This has happened before and corrected himself. Maybe one setting in another program? ___

  I select a screen saver, set the time, apply and nothing.  This has happened before and corrected himself.  Maybe one setting in another program? It's on a laptop.

  Hello jerrylumpe

  1. If you use an old mouse, try to clean it.

  2. you can have a running process in the background that keeps XP thinking that he is busy and so the screen standby does not start.
  Go to msconfig and uncheck everything you don't need, then see if the screensaver will kick in.

  Start/run and type
  Msconfig
  Ok

  Startup tab
  Keep the page open then click on the link below. It will tell you what are all the entries and see if you can disable them or not

  http://www.SysInfo.org/STARTUPINFO.html

  Read the key at the foot of the page, then click on "Here" at the top. Use the search box to check all your entries

  Try this too
  http://www.kellys-Korner-XP.com/xp_tweaks.htm

  Line 51 left side. Click on "toggle".

  It could be that something is resetting the timer. For example, it does take much vibration to move the mouse a little, and which will reset the timer to zero. Something like that would be possible? Or a pet that walks on the keyboard?

• Satellite Pro L450D black screen and will not respond to any keys

  Hello

  My niece has used his Toshiba L450D for almost a year now and he really liked it, who was until last month. She turned on her laptop and when she presses the button of the mouse, the button cracked and he fell into the laptop.

  Now my brother contacted Toshiba and I was told because it is under warranty it might return for repair because it was a common fault. Then he he packed in loads of air bubbles and a box to make sure it was safe.

  A few weeks later he came back repaired but we were all shocked that the laptop was put in a very loose box and you could hear this rattling noise. When we turned on the battery was flat and we had a new boot menu.

  As she installed it Windows 7 laptop would boot directly into Windows 7, but now after the repair of the laptop shows a menu black screen with as follows:

  + Windows 7 +.
  + Recover Windows to Factory Settings [active EMS] +.

  So we started in Windows and everything went well, but now after 5 or 10 or even 20 minutes, laptop displays a black screen and will not respond to keys or mouse movement. There is nothing on the screen its just black.

  I started in SafeMode (which was more difficult with the new menu) and it does the same thing. I even managed to do a virus scan quick who took 3-4 minutes and was clean.

  I would like some advice on what my niece is very angry, and it's difficult to explain what is happening to a child in the primary school.

  Any help would be grateful.

  Hello

  Have you tried the option of HARD drive recovery?

  If this is not the case, try to set the notebook back to factory settings using HARD drive recovery.
  Turn on the device, press F12, choose repair my computer, then select Toshiba HDD recovery.

  I hope it will work!

• I accidentally put 100 files on my desktop and it went to black screen and will not work

  I accidentally put 100 files on my desktop and it went to black screen and will not work

  Hello

  Following methods and check if that helps.
  
  Method 1:

  Step 1:

  Start your computer in safe mode and check if it starts very well.
  
  Step 2:

  If the system starts in safe mode, then there would be a third-party software, causing the issue to occur. I wish that you start your machine in a clean boot State. Clean boot helps eliminate conflicts of third party software.

  Note: Follow step 7 to your computer as usual.

  Method 2:

  If this does not help, you can perform System Restore in safe mode.

• Screen saver does not start automatically

  original title; SCREEN SAVER DOES NOT START AUTOMATICALLY

  My screensaver stopped automatically to come if I use an excerpt it's turns on and will remain lit.  How can I fix or can uninstall and reinstall?

  It becomes a problem growing with the screen savers. The issue is background programs and services that are enough tasks that the computer never thinks that it becomes "inactive". Programs cannot do any real work, but are cycling through their operations individual enough to keep the computer "awake".

  Try to start your computer with a "clean boot", (see Microsoft Support articles below). If this resolves the issue and you definitely want your screen saver, you'll have to discern what substantive programs and services that you can live without being active all the time, and turn them off.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135

  Perform a clean boot to determine if background programs interfere with your game or program
  http://support.Microsoft.com/kb/331796

  For what it's worth, the systems that I watched recently with this problem were 'smart phone' synchronization software recently installed and who is constantly looking for something to synchronize with regardles to know if they are connected to what whether or not. Change the start of these programs and services 'on demand' to 'always' solves the problem in these cases.

  • If this proposal of solution solves your problem, please go back and mark as answer for others to consider.

• Qosmio F750-03W - face recognition does not start and the video freezes

  I apologize for my English.

  NVIDIA 3D test shots of program wheel. Face recognition does not start.
  If the activator of the image that 3D is disturbed and I do not see the image in 3D.

  If I try the Games 3D compatible (Left4Dead) active 3D 1080 p, but the game is choppy as the test 3D image not turn on face recognition.
  3D game is to see the 2D to 3D pictures, but how do I vadere photos in 3D?

  If the Activator active 3D image quality is mediocre.
  I have defined normal and advanced, but videos have gost especially on side effects.

  Hello

  It looks like your Qosmio F750-03W PQF75C 03W001 is a Canadian model of Toshiba that I found it here:
  http://support.Toshiba.ca/support/ISG/Center/en/index.asp?S1=notebook&S2=Qosmio&S3=F750&S4=PQF75C-03W001

  First you need to update the BIOS with the latest version (at this time, it seems that BIOS 2.0 is the most recent).
  Also update the
  nVidia Display Driver version 8.17.12.9039
  Super-D IC Driver version 1.0.1613.809
  Toshiba Blu - ray Disc Player version 1.0.1.299
  as mentioned here http://support.toshiba.ca/support/isg/tsb/en/view.asp?docid=TSB001633

  If stereo 3D effects are not well use X-tune to calibrate it.
  It is recommended to use this utility to optimize the 3D stereo effects when you use the 3D without glasses for the first time or to be dissatisfied by the 3D effects.

  To use the X-Tune utility, follow the steps below:
  1. Select the language mode and optimization, and then click OK. There are three optimization modes: primary, advanced and professional. You can choose according to your own experience.
  2 sitting about 60 cm from your computer, click Start to continue.
  3. follow the onscreen instructions on each step.
  4. use the left or right side of the keyboard arrow key to adjust the effect. When you are satisfied with the effect, click on enter and then an information window appears on the screen. Press the keyboard ESC key to cancel the optimization procedure.
  5. click on Finish to close the X-Tune utility.

  You said that your face recognition does not work correctly so uninstall this software. This also with the software/driver for webcam. Once these two tools has been uninstalled, clean the registry with CCleaner and install these two tools using the most recent version.
  Restart and start X-Tune to calibrate the 3D effects.

  In the doc of Toshiba (link above), you can find this notice:

  1. the value [screen resolution] 1920 x 1080. Glasses free 3D mode is not activated except in mode 1920 x 1080.

  2. depending on the game, it does not work with glasses free 3D mode and with the 2D mode.

  3. depending on the game, it display correctly with stereoscopic 3D mode

  4. the game does not appear with glasses free 3D mode when you run drive Blu - ray TOSHIBA with glasses free 3D mode
  or run TOSHIBA Web Camera application.

  5. the performance of the game will be reduced when the game with glasses free 3D mode. If the game performance is considerably diminished, please reduce the quality of the image of the game by using parameters
  of the game. If the performance of the game are still not sufficient, please disable mode 3D free glasses by uncheck [Enable stereoscopic 3D] to the NVIDIA Control Panel.

  6. small fonts in games can be difficult to read with the glasses free 3D mode. At this time, please press the PC 3D and temporarily disable glasses free 3D mode. Glasses free 3D mode is enabled if you again press the 3D button

  7. the response of the game may delay with glasses free 3D mode. If you feel it and can not enjoy the game, please disable mode 3D free glasses by uncheck [Enable stereoscopic 3D] to the NVIDIA Control Panel.

  8 glasses free 3D mode can be disabled temporarily by pressing the PC 3D button, but it can be activated by playing game. At this time, please press the 3D button and turn it off again.

  9. when [enable stereoscopic 3D] in NVIDIA Control Panel is not checked, the game will start with 2D mode. At that time, glasses free 3D mode is not enabled even if you press the button during the game PC 3D.

  10 glasses free 3D mode may be turned on except TOSHIBA Blu - ray player and games. Currently, please turn off the 3D mode free glasses by uncheck [Enable stereoscopic 3D] to the NVIDIA Control Panel.

  11. the color of the video may be different from the original during video playback with full screen on RGB and not 3D TV if [enable stereoscopic 3D] is checked. Currently, please turn off the 3D mode free glasses by uncheck [Enable stereoscopic 3D] to the NVIDIA Control Panel.

  I hope this helps.