Question about an A500 Sony DSLR

Similar Questions

• Questions about TV Tuner Satellite A500/040

  Hi all

  I'm new to the Tuner of TV analog digital hybrid and I'm sorry if my questions seem as stupid.

  I have two questions about the of digital TV Tuner analog integrated hybrid in the Notebook Toshiba Satellite A500/040. My understanding is that the TV tuner hybrid integrated able to decode TV signals high definition and their display on TV via its HDMI port. I wonder if I could watch TV shows on your laptop without connecting to a TV. If so, is the software needed? There are several USB TV tuners for desktops and laptops on the market, A500 hybrid TV tuner works differently these USB TV tuners?

  Thank you

  Young

  > I think I know that the TV tuner hybrid integrated able to decode TV signals high definition and their display on TV via its HDMI port.

  N ° this s tv tuner not a HD!
  It s a digital tuner that provides digital video signal 576i and not 1080i.

  Of course, you can use the HDMI port to connect the laptop to the LCD HDMI port but you will not get the quality video full HD as blueray for example.

  I found this Australian page from Toshiba:
  http://www.MyToshiba.com.au/products/notebooks/satellite/A500/psam3a-04000e

  You will find this passage short text:
  + With tuner TV built-in, you can even watch analog or digital TV everywhere where you travel, while the HDMI ports make connecting high definition on your TV screen and sound system. +

  You can also watch TV on mobile phones display! It's a key reason why the TV tuner built in ;)

• question about cleaning the sensor of the A57

  Dear community of Sony,

  I have several questions about the cleaning of the sensor of the A57.

  Recently, I noticed several dark specs appearing on images when shooting at low opening (F20, F22), especially when there are high for them (like the sky in a landscape photo) contrast. To my knowledge, I've categorized as possible of dust on the sensor. I have read the section of the manual about cleaning the sensor and followed the procedure. However, the problem remained. I have previous experience with cleaning of the more resistant the probe of a Sony NEX dust particles, so I applied it to the A57. I used the specialized sensor cleaning tools combining two parts kit - wet and dry. Noted little dust on translucent mirror as well, so I cleaned up afterwards. Later, I considered this mirror could have some specialized coatings.

  So my first question is: should I have done some permanent damage the mirror or the sensors? Currently, the camera works OK, although some features of dust still remain. It seems that I had pushed some of them to the edges of the sensor.

  I'm not so happy with the tool that I used. I'm thinking about this one for a more thorough cleaning:

  http://www.digitaltoyshop.co.UK/Eyelead_sensor_cleaning_kit_SCK-1_Sony_Alpha_A57_t2836_6789

  It is marketed as a tool for A57. Should I use it?

  Thank you in advance?

  Best regards Angel Marinov

  PS: I'm really happy with my Sony A57 and the NEX. They made me a fan of Sony. So, I want to use this topic to also say thank you to the developers of Sony.

  Hello Angel!

  Read the following steps carefully and let us know if you have any other questions.

• Where can I ask a handful of general order questions about Firefox OS as a consumer and get the answers? (a forum or something similar)

  I have about seven questions about Firefox OS. I'm potentially interested in opting for a tablet that works instead of Android or iOS. I couldn't find a place to ask questions like that. Thank you!

  https://support.Mozilla.org/en-us/forums/Firefox-OS-English-Forum

  There is another option.

• About a month ago I posted a question about iMovie and not being able to "share". I solved the problem thanks, so no more emails!

  About a month ago I posted a question about iMovie and not being able to "share". I solved the problem thanks, so no more emails!

  Hi Michael,

  If you want to stop receiving notifications by electronic mail, in the thread, that you have created, then I suggest that you follow the steps below:

  One time connected to the Apple Support communities, visit your mini profile and select manage subscriptions.

  

  Content

  To manage this content, you are currently subscribed and changing your preferences, select the content.

  Select next to see what content you are currently following.  Note that any thread you are responding you subscribe you automatically to this thread.

  You can select to terminate a subscription to a thread.

  

  Learn how to manage your subscriptions

  Take care.

• Where and how do I ask questions about Email?

  The Commission opening thingy is complicated, I have trouble finding my way around it.  I don't know where or how questions about email.  Is there an easier way than trawling through all these icons?  Like a list or something - as you get on all other forums on the internet?

  It would be a good starting point: Mac mini

  Or the appropriate under MAC Os and system software section.

  You might also find this useful: find answers and new questions

• Many questions about the HP 50 g

  I just ordered a HP 50 g graphic calculator! I have a few questions about this so hang on tight! What is the USB connector on the calculator? Mini-USB, micro USB, or is it a connector owner, "custom". Then, it would be possible to connect a keyboard to the HP 50 g by using the USB Port? Is there a program that would make this possible? (I doubt it would work if you plug it..) I have a Mini-USB to female USB 2.0 connector. So I could just plug the keyboard right, provided that the port on the calculator is a Mini-USB Port. If this is not so that I could use my female to female USB adaptor to connect the keyboard.

  Thanks for your help,

  Zekelegge

  Hi!, zekelegge:

  Welcome to Forum!

  The only printer I use, 50G calculators, 48GII, 39GS and 17BII +, as well as many former models, such as the 48 s/SX/G/G + / GX, 38 G, 39 G, 42, 41 C/CV/CX and 28 C/S, is the infrared printer HP 82240 b. If you can use the emulator HP50G, on the PC, the simulator of the printer, you can download, since... http://www.HPCalc.org/details.php?id=7386

  The printer... HP 82240 B

  

  The cable series...

  

  The description... http://www.allenwan.com/hpcalcserialcable/

  The original cable...

  

• Question about warranty after exchanges of RAM on Satellite module series

  Hello together,

  I have a question about the warranty. My laptop is 5 months old and now I want to improve it with more RAM. I want to do it myself, and now I'm wondering if the warranty will be getting hurt.
  Thanks in advance for your answers.

  Concerning

  TiG3r

  For new models of laptops the RAM upgrade described in s operating manuals. It is public act and it shows the owner of the notebook how do RAM upgrade only.

  If Toshiba offers something like this he won't have the negative influence of valid warranty.
  Buy a compatible module and RAM upgrade.

  Bye and good luck!

• A few quick questions about the Satellite P300 - 18 M

  Hello

  I am about to order a Satellite P300 - 18 M and have just a few questions about this:

  (Although these may apply for other similar Satellite/Equium P300.)

  Is the touchpad made by / to use the Alps or Synaptics driver?

  It has the Wireless N network card, is the map made by Intel or Realtec?

  And also, someone has experience with face recognition software to connect?

  If so, does it take a lot of time to initalise?

  Thanks in advance,
  Jack

  Hello

  The P300 - 18M belongs to the PSPCCE series.
  It uses the two touchpad drivers. Synaptics & Alps Electric
  There is an Intel 802.11agn minicards WLan installed

  The face recognition is a nice tool but local to be illuminated and you must take your face the right of the post sometimes it of not very easy

  But if you face is recognized correctly that the connection should work properly

  See you soon

• Questions about nb200

  I recently bought a mini nb200 with windows 7 and I have a few questions about it. How can you set up your email, I was willing to put up with Outlook Express, but I don't know if I can. Also, is there a way to get a paper copy of the user manual?

  You can download and install a new e-mail program when you download Windows Live via Microsoft Update. You can select the components of Windows Live, you want to include by checking a box for each you want. I installed all the. Or you can use Outlook, if you have Microsoft Office and you want to install it.

• A few questions about the difference between the Satellite P70, L70, S70

  Hello, I have a lot of questions about the P70, L70, S70 series that come with a 1920 x 1080 panel.

  (1) what are the differences between the L70 and S70 series? With the exception of the RAM and HARD drive capacity, books seem pretty identical.

  (2) P70, L70, S70 doesn't support a 2nd HARD drive or it's just the P70 series that support?

  (3) all the three (P70, L70, S70 series) come with the same TFT panels?

  (4) of the above series, which supports mSata?

  (5) all the model of each series are delivered with support from mSata? For example, it could be that L70 - a - 13 m supports mSata is not the case of the L70-a-146?

  (6) all the foregoing, are delivered with a S - ATA II or III S - ATA interface?

  (7) who is the best of these series listed? I'm trying to understand what makes the big difference of S70 to P70 except for the envelope for example.

  Thank you in advance.

  > (1) what are the differences between the series L70 and S70? With the exception of the RAM and HARD drive capacity, books seem pretty identical.

  What models Sat L70 and S70 do you mean exactly? There are different L70-xxx-xxx and S70 models on the market that supports different hardware specifications.

  (> S70 2) P70, L70, support a 2nd drive HARD or is - it just the series P70 that support?
  As you can see in this [Sam P70 HDD replacement document, | http://aps2.toshiba-tro.de/kb0/CRU3903II0000R01.htm] the P70 series supports the 2nd drive Bay HARD, BUT even if there is a 2nd HARD drive Bay, this does not mean that you can use the 2nd HARD drive. In the case where the 2nd HARD drive Bay are equipped with HARD drive connector, you can use the 2nd HARD drive

  I also found the [Sam L70/S70 HDD replacement | http://aps2.toshiba-tro.de/kb0/CRU3703HG0000R01.htm] the document on the Toshiba page and there I see this 2nd HARD drive Bay is not available

  (> 3) all three (P70, L70, S70 series) come with the same TFT panels?
  See point 1). Different P70, L70, S70 models were equipped with different material parts.

  (> 4) of the series above, which takes in charge mSata?
  As far as I know that some P70 models are equipped with an mSATA SSD of 256 GB.

  (> 5) do all the model of each series are delivered with support mSata? For example, it could be that L70 - a - 13 m supports mSata is not the case of the L70-a-146?
  See point 4) not all models supports the same hardware specifications

  (> 6) all of the above, come with a S - ATA II or III S - ATA interface?
  I don t think that SATA III is supported. I guess it would be SATA II

  (> 7) which is the best of these series listed? I'm trying to understand what makes the big difference of S70 to P70 except for the envelope for example.
  Not easy to answer because there are too many models released in Europea.
  And not all models are available in each country. So I guess you will have to look for the models that have been released in your country.

• Satellite L650-11R - a few questions about this

  Hello there :-)

  I have a few questions about my new L650.

  I've never had Toshiba notebook before so I apologize if some of these "quirks" are actually quite normal on this laptop. I really want to hear the views of other users L650.

  1)
  First of all, by the time I turned it on I saw gradient thin (1-2 mm) along the right edge of the screen that goes from the bottom up. Maybe "degraded" isn't the right word, but it seems that since two or three pixels are kind of discoloration or lose brightness/sharpness to the edge along the straight bezel. It is not really that visible, looks like the colors are desaturated a bit here or brightness is a bit lacking. He can be seen everywhere (bios or no color in Windows, but better in the lighter background).
  The left side (or other) seems ok, all this along the right edge is somewhat suspicious. If one can compare? I don't know if it's something to worry about or is just supposed to be like that.

  2)
  The other thing I noticed heating of the processor (Intel i3 330M) and GPU (ATi Mobility Radeon 5650). It's pretty hot here right now (I would say that the temperature is around 28 degrees Celsius when using cell phones). He is sitting on the hard surface (table) and nothing is blocking the vents.
  However, at "rest" (surf the web & regular light stuff), average CPU temp hovers around 58 ° C. It usually goes from 45 to 62 in just a few minutes after starting, and then I can hear and see (Toshiba PC Health Monitor) evacuate the kicks in. Temp goes back to 50 +, event stops and then the temp rises to 60 + until the vent is used again.
  During load full (Prime95 or some games), CPU is going all the way up to 75 degrees (the highest being 77). Fan runs at 75 to 77% during this time, never go faster.

  GPU idling is usually around 5 degrees above temp CPU (62-65). During full load (for example. Benchmark of Far Cry 2), I see a lot of stuttering with the latest drivers Catalyst and DX10 (not sure if the stuttering has something to do with heat), otherwise it is ok (no artifacts or anything like that). Temp of GPU during the loading goes up to 74-75, fan speed is locked at 30%, the frequency of the heart 5650 is 450 MHz. left side of the laptop (vent and below) is pretty hot, while the keyboard is warm (or slightly warmer who who).

  These time seems correct and safe in the long term? I'd rather events works all the time (they aren't really very strong) and keeping time less than 50, but there are just wishful pious bios control events and I can't control not the bios. :-)

  3)
  This is just General related products. :-)
  Official specifications of Toshiba L650 say ATi 5650 (between other low range GPU), but I saw a few specifications calling for there 5730 (same model 11R). Is there really a Satellite L650 with ATi 5730 GPU models?

  Sorry for the long post, I tried to include the best possible description that I could do. :-)

  Thank you in advance.

  Thanks for the additional info!

• Hi there, I have a question about storage, even if I have 2, 53GB, storage watch 21, 99GB usage, why this difference? I use an iMac 2009, thank you!

  Hi there, I have a question about storage, even if I have 2, 53GB, storage watch 21, 99GB usage, why this difference? I use an iMac 2009, thank you!

  Spotlight re-indexing.

• A few questions about the upgrade on Satellite A300-144

  Sorry for the typos, English is not my mother tongue.
  I want to ask some questions about the upgrade of a300-144.

  * Some info first.*

  CPU: T2370 ([http://ark.intel.com/products/34445/Intel-Pentium-Processor-T2370-1M-Cache-1_73-GHz-533-MHz-FSB]).
  Chipset: GM965 ([http://ark.intel.com/products/29821/Intel-82GM965-Graphics-and-Memory-Controller]).

  * Questions.*

  1. my frequency of laptop memory at 533 MHz, supports 667 MHz memory controller, memory modules can work at 667 MHz. Is - this because CPU FSB 533 MHz frequency and new processor at 667/800 MHz FSB will fix it or it is hardcoded in the BIOS?

  2 Intel said that the size of max memory for my chipset is 4 GB (2 x 2 GB), but Toshiba says that only 2 GB (2 x 1 GB), who is right?

  3 I know, taken of my CPU is μFCPGA-478 aka socket P, max FSB 800 MHz, max 35 W TDP, so T9500 ([http://ark.intel.com/products/33918/Intel-Core2-Duo-Processor-T9500-6M-Cache-2_60-GHz-800-MHz-FSB]) is a compatible processor or there are some limitations in the BIOS?

  > 1. My frequency of laptop memory at 533 MHz, supports 667 MHz memory controller, memory modules can work at 667 MHz. Is - this because CPU FSB 533 MHz frequency and new processor at 667/800 MHz FSB will fix it or it is hardcoded in the BIOS?

  The speed of the memory is related on the material. This means that the FSB is responsible for the limitation.
  If the FSB would allow support 667 MHz then the memory would also at this speed.

  > 2. Intel says that the size of max memory for my chipset is 4 GB (2 x 2 GB), but Toshiba says that only 2 GB (2 x 1 GB), who is right?
  The memory depends on the chipset. So if the chipset supports 4 GB of RAM, you should be capable of this move to 4 GB of RAM

  > 3. I know, my CPU is? FC-PGA-478 aka socket P, max FSB 800 MHz, max 35 W TDP, so T9500 (http://ark.intel.com/products/33918/Intel-Core2-Duo-Processor-T9500-6M-Cache-2_60-GHz-800-MHz-FSB) will be a compatible processor or there are some limitations in the BIOS?

  It might be possible that the new processor would be fully supported by the BIOS, but in most cases it should not be a problem if the chipset would support the new processor.
  But as far as I know the upgrade of the CPU is not supported by Toshiba or any other manufacturers of portable and its your own risk to run laptop with the new processor.

• Satellite A350D - 20K - Question about upgrade second HDD + Temperature

  I have a question about my laptop. I have notticed it is a second location of HARD disk on the bottom.
  Is it possible to use this to increase my storage?
  And if yes, how do I do that? I don't see all the connectors.
  What type of HARD drive to use in case it is possible to use this slot machine?

  My second question is on my laptop to be very hot after a short period of use.
  I installed speedfan to record the temperature. When I start the laptop, it already is between 45 and 50 degrees.
  He stayed there for half an hour and then it starts to get warmer. When I start to use the laptop for anything, it triggers to between 70 and 80 degrees.

  This does not seem normal to me. I tried to clean the vents with compressed air, but it has not made a difference.
  I searched on the internet how to take the laptop part for proparly cleaned TI.
  But I can't so I'm looking that destroy it.

  This could be the cause and more importantly, how can I solve this problem?

  Tom

  The second HARD drive bay contains the HARD drive connectors?
  If Yes, then you can use a SATA 2.5 HARD.
  If there are no connectors, then you will not be able to use the second HARD drive

  > I have installed speedfan to record the temperature. When I start the laptop, it already is between 45 and 50 degrees. He stayed there for half an hour and then it starts to get warmer. When I start to use the laptop for anything, it triggers to between 70 and 80 degrees.

  CPU and GPU produce a lot of heat. The heat dissipation is always created then there s nothing unusual that the temperature rose to higher level.
  You can change the settings in Win 7 power management. You can set the CPU to lower performance and can increase the activity of fan, which will help lower the temperature.