Question about the reduction of noise/hiss & fade in and out

Hello I am new to hearing. I use Audition CS5.5. I was wondering how I can remove the "whistling" singing (whenever the words with "s" or "EC" are sung as "silence" or "stones"). I have a multitrack project open and I have the vocal track selected, but the function "hiss reduction" Effects-> noise reduction/restoration is gray. Similarly, "noise reduction" and "capture point noise" is also grayed out (even if I have a section of the track selected with the time selection tool). Why are these unusable?

Another question is how can I add fade in/out effects in multitrack view? I know that I can draw lines for the fade in and out while a single track is selected, but I always like to use multitrack view, while working so that I could easily move the vocals to match the music.

Thank you.

Noise reduction is an effect that only works in Edit/Waveform mode.  It doesn't have multitrack real-time.

However what you're saying, your problem is the sibilance not "whistling" anyway.  Hiss reduction is there to get a constant background hissing like a pre amp out in noisy mic.  You may do better by using what is called a De-Esser which you find in the FFT filter under filters and EQ or compressor multiband in the effects of Amplitude and Compression.  I must be a bit vague because I've never bothered with CS5.5 in order to remember here is that it was these effects.

On your other question, you have "volume envelopes" in multitrack view and can 'draw lines' it too.  If you do not get them, go to the view menu and make sure that "Show Clip Volume envelopes" is checked.

Tags: Audition

Similar Questions

  • Drawn with the pencil tool seems to fade in and out

    My Nme is Allen Togwell.Case No.: 0183721415. Your type of chat line says I need a graphics card to solve my problem for my CS6. He gave a link but disconnected before I could use it. Can you help me with what type of graphics card, I need. I am 75 years old and not very literate com.

    Thank you

    Hi Allen,.

    I looked at the file number and watched a recording of you work with the agent and I am not convinced that what you see is necessarily due to the graphics card.

    This is my interpretation and thoughts around what have seen you. I noticed that you are working on an image that took a good amount of the screen seen in the zoom of 16.7%. In other words, that it was a large enough image. Then I noticed that you use the pencil tool with a piece that was 4 pixels.

    I think that the combination of these two things was the reason for which the pencil tool appeared jerky or fade in and out when establishing. This happens because you are using such a small size and are zooming back as long as the lines are barely visible. When you zoom in her resamples program appearance. This resampling can cause detail to be lost and the appearance of vary depending on what level of zoom is used, 16.7% is particularly bad, with fine detail.

    I think that there are two solutions, use a different zoom level to get a better view or use a pencil with a larger size.

    I recorded this video for you for example

    http://screencast.com/t/e9dhiHKoKbv

    I suspect the list that the agent was suggested for video cards was at the bottom of this document

    http://helpx.Adobe.com/Photoshop/KB/Photoshop-CS6-GPU-FAQ.html

    Hope that helps,

    -Dave

  • Satellite M70-340: Question about the warranty if I buy in Russia and move to Australia

    I would buy the Satellite M70-340 laptop here in Russia. Next month I'll move to Australia. What the warranty in this case?

    Will I be charged if problems occur?
    How can I recognize a laptop that is officially sold (= I mean legally delivered and comes with a guarantee in the world)?

    Thank you very much for your answer!

    To my knowledge, you can save your laptop on the European site of Toshiba for services and extensions of warranty and uprisings.
    The serial number of the laptop must be registered generally on this site.
    I think you can buy a few additional warranty packages that allow you to get the guarantee availability in the world.

    But usually if something goes wrong on the laptop you will need to contact Toshiba authorized service partner in your country.
    On the Toshiba support page, you will also find a database for service partners worldwide.

  • Question about the music library to iCloud (music Apple) and iTunes on mac

    Download I m just of my iTunes in the music library of iCloud library. Since I was afraid that my library of 40000 + titles could get corrupted or metadata could be changed by apple, I downloaded the files from a 'second' machine (macbook) - just to be on the safe side and keep my iTunes library local main on my iMac intact by iCloud (for the moment).

    Now everything seems fine with iCloud music library, but after all the titles/songs are in iCloud now, what happens if I disable the library iCloud music on the 'second' machine and Activate the library iCloud music on my main machine (iMac), which has the same local as my second machine iTunes library? (= the same local iTunes library, which has been already downloaded?)

    ICloud/iTunes will recognize that all songs/files are already uploaded to the music library iCloud and doe 'nothing', or download will process all over again and will lead to 'double' all the files/songs in iCloud?

    The same question arises if we restore iTunes library local on a mac from a backup + switches on iCloud music library a second time... will be iTunes + icloud music library download all the files again or not?

    Unless something is wrong, it should recognize and not duplicate.

  • General questions about the system reserve partition in windows 7 and 8

    Hello

    1. is the partition of the system 100 MB in windows 7 hard disk is to use system restore?

    2 - on the track of the first hard disk that 100 MB partition holds system resides?

    3. in windows 8 wat happened with this partition of booking sytem 100 MB and where it is located on the hard drive?

    Thank you

    Johan

    Hello

    1. is the partition of the system 100 MB in windows 7 hard disk is to use system restore?

    2 - on the track of the first hard disk that 100 MB partition holds system resides?

    3. in windows 8 wat happened with this partition of booking sytem 100 MB and where it is located on the hard drive?

    Thank you

    Johan

    It should appear as disk 0

    This is for the Windows recovery environment (WinRE), also supplied with Windows Vista, only it has been available from the Windows Vista installation disc only, although some manufacturers make available on a partition separated on their factory facilities. In Windows 7, this feature is installed on all computers and is stored in the 200 MB partition if you are installing using a single partition scheme. However, if you are installing to a drive that has more than one partition, the recovery environment is stored in a folder at the root of your installation disc, so if you install to a partition with a label of C:\ she will be C:\Recovery.

  • Questions about the implementation of clusters of storage and DTS on active cluster

    I have a few questions about the implementation of clusters of data store and SRS storage in VSphere 5.1.

    We have a data center with about 15 HP blades and a few servers non-lame.  The hosts are all either VSphere 5.0 or 5.1.  Our back-end storage is an EMC VNX 5700 with about 20 stores of data.  All the VMWare is managed by VCenter 5.1 running on a dedicated physical machine.

    Currently, each data store is used individually; No piles of data store are put in place.  When a new virtual machine is created, the administrator usually chooses the data with the most space store.  Periodically, we will go back and manually storage vMotion machines to balance the load.

    Recently, we have expanded the VNX storage, so we now have LUNS in different pools, with different levels of performance.

    What I would do is set up for the data store clusters, so that us when a virtual machine is created, the administrator must not know what data store is in which pool.  Also take advantage of the DRS storage so that the burden of storage will be "refine" himself a little.

    I know the setting up of a cluster of storage in a 'clean' environment is quite simple, but my concern is creation/conversion data warehouses existing in active production in the cluster, while they are used.

    If I access the screen "data warehouses and store data from clusters ', right-click on the data center and create a cluster, and then move the various data stores in the new cluster, will there be an interruption in the production running systems?

    I also wonder about activation of storage i/o control.  It is not currently enabled on data warehouses.  I know it's useful for the StorageDRS, but will be allowing any negative impact on the system?  If I turn on the warehouses of data, is there anything else I should do or set in addition to all that allows him?

    Finally, we are in the process of Site Recovery Manager configuration.  SRS has an impact on the configuration of the data clusters and DTS store?

    Thanks in advance for your comments.

    Mike O.

    Gregg Robertson wrote:

    Hello

    Clusters of data and using DTS store doesn't impact RS even if you create a cluster of data store for storage of replicated data and another for everyone else, this way you machines virtual you want to replicate are not moved on warehouses of data that are not replicated , but will still have the ability to move if there is a conflict.

    Gregg

    With all due respect but SRM and DTS don't go together. SRM does not at all support the use of DTS. So if you are configuring SRM forget DTS for now.

    Reason for this is that SRM knows no DTS and VMs can be in flight when a failover should occur, and bad things can happen. Also, the protection breaks when a virtual computer is moved between data warehouses in a cluster data store.

    In short: don't go there.

  • Where should questions about the JDEV/ADF positions?

    Hello

    Where should questions about the JDEV/ADF positions?

    JDeveloper and ADF or

    JDeveloper and ADF?

    I found there may be some different advantageous:

    https://forums.Oracle.com/message/11109674?TSTART=0#11109674

    Thank you.

    Well, the other forum you mentioned is the Korean equivalent of the English forum.

    You have already discovered, it is not controlled to many users. I didn't know that it exists at all.

    In general it is to you where you ask your questions. All for one here are driven by the community and some employees of the Oracle, you cannot wait has answered all your questions. If you really need to answer you go through paid support.

    A tip for getting help is to provide a well-defined use cases, information relating to your environment and documented code showing what you have already tried.

    Timo

  • A few questions about the difference between the Satellite P70, L70, S70

    Hello, I have a lot of questions about the P70, L70, S70 series that come with a 1920 x 1080 panel.

    (1) what are the differences between the L70 and S70 series? With the exception of the RAM and HARD drive capacity, books seem pretty identical.

    (2) P70, L70, S70 doesn't support a 2nd HARD drive or it's just the P70 series that support?

    (3) all the three (P70, L70, S70 series) come with the same TFT panels?

    (4) of the above series, which supports mSata?

    (5) all the model of each series are delivered with support from mSata? For example, it could be that L70 - a - 13 m supports mSata is not the case of the L70-a-146?

    (6) all the foregoing, are delivered with a S - ATA II or III S - ATA interface?

    (7) who is the best of these series listed? I'm trying to understand what makes the big difference of S70 to P70 except for the envelope for example.

    Thank you in advance.

    > (1) what are the differences between the series L70 and S70? With the exception of the RAM and HARD drive capacity, books seem pretty identical.

    What models Sat L70 and S70 do you mean exactly? There are different L70-xxx-xxx and S70 models on the market that supports different hardware specifications.

    (> S70 2) P70, L70, support a 2nd drive HARD or is - it just the series P70 that support?
    As you can see in this [Sam P70 HDD replacement document, | http://aps2.toshiba-tro.de/kb0/CRU3903II0000R01.htm] the P70 series supports the 2nd drive Bay HARD, BUT even if there is a 2nd HARD drive Bay, this does not mean that you can use the 2nd HARD drive. In the case where the 2nd HARD drive Bay are equipped with HARD drive connector, you can use the 2nd HARD drive

    I also found the [Sam L70/S70 HDD replacement | http://aps2.toshiba-tro.de/kb0/CRU3703HG0000R01.htm] the document on the Toshiba page and there I see this 2nd HARD drive Bay is not available

    (> 3) all three (P70, L70, S70 series) come with the same TFT panels?
    See point 1). Different P70, L70, S70 models were equipped with different material parts.

    (> 4) of the series above, which takes in charge mSata?
    As far as I know that some P70 models are equipped with an mSATA SSD of 256 GB.

    (> 5) do all the model of each series are delivered with support mSata? For example, it could be that L70 - a - 13 m supports mSata is not the case of the L70-a-146?
    See point 4) not all models supports the same hardware specifications

    (> 6) all of the above, come with a S - ATA II or III S - ATA interface?
    I don t think that SATA III is supported. I guess it would be SATA II

    (> 7) which is the best of these series listed? I'm trying to understand what makes the big difference of S70 to P70 except for the envelope for example.
    Not easy to answer because there are too many models released in Europea.
    And not all models are available in each country. So I guess you will have to look for the models that have been released in your country.

  • A few questions about the upgrade on Satellite A300-144

    Sorry for the typos, English is not my mother tongue.
    I want to ask some questions about the upgrade of a300-144.

    * Some info first.*

    CPU: T2370 ([http://ark.intel.com/products/34445/Intel-Pentium-Processor-T2370-1M-Cache-1_73-GHz-533-MHz-FSB]).
    Chipset: GM965 ([http://ark.intel.com/products/29821/Intel-82GM965-Graphics-and-Memory-Controller]).

    * Questions.*

    1. my frequency of laptop memory at 533 MHz, supports 667 MHz memory controller, memory modules can work at 667 MHz. Is - this because CPU FSB 533 MHz frequency and new processor at 667/800 MHz FSB will fix it or it is hardcoded in the BIOS?

    2 Intel said that the size of max memory for my chipset is 4 GB (2 x 2 GB), but Toshiba says that only 2 GB (2 x 1 GB), who is right?

    3 I know, taken of my CPU is μFCPGA-478 aka socket P, max FSB 800 MHz, max 35 W TDP, so T9500 ([http://ark.intel.com/products/33918/Intel-Core2-Duo-Processor-T9500-6M-Cache-2_60-GHz-800-MHz-FSB]) is a compatible processor or there are some limitations in the BIOS?

    > 1. My frequency of laptop memory at 533 MHz, supports 667 MHz memory controller, memory modules can work at 667 MHz. Is - this because CPU FSB 533 MHz frequency and new processor at 667/800 MHz FSB will fix it or it is hardcoded in the BIOS?

    The speed of the memory is related on the material. This means that the FSB is responsible for the limitation.
    If the FSB would allow support 667 MHz then the memory would also at this speed.

    > 2. Intel says that the size of max memory for my chipset is 4 GB (2 x 2 GB), but Toshiba says that only 2 GB (2 x 1 GB), who is right?
    The memory depends on the chipset. So if the chipset supports 4 GB of RAM, you should be capable of this move to 4 GB of RAM

    > 3. I know, my CPU is? FC-PGA-478 aka socket P, max FSB 800 MHz, max 35 W TDP, so T9500 (http://ark.intel.com/products/33918/Intel-Core2-Duo-Processor-T9500-6M-Cache-2_60-GHz-800-MHz-FSB) will be a compatible processor or there are some limitations in the BIOS?

    It might be possible that the new processor would be fully supported by the BIOS, but in most cases it should not be a problem if the chipset would support the new processor.
    But as far as I know the upgrade of the CPU is not supported by Toshiba or any other manufacturers of portable and its your own risk to run laptop with the new processor.

  • Question about the recovery partition

    Hello.

    I have a question about the recovery of HARD drive partition.

    If I do the operation to clear the hard disk option in the wizard it will remove * all * or it will keep my partition recovery in this way I can come back later. I want to know because I would like to put on a different OS.

    I know he said he would, but caution in the PDF, I found it says that on a normal recovery too (that he would remove each partition) and I'm a little confused about how the recovery actually worked.

    Thank you.

    Hey Buddy,

    To be honest I n don't know what you mean exactly with this option to erase.

    In General, Toshiba Recovery disk will wipe your entire HDD to restore factory settings correctly. This means that if you start from that disk and follow the instructions on the screen, everything will be removed.

    In addition, the recovery disk doesn t create a recovery partition. It is not available. Disk copy just the files on the second partition in folder HDDrecovery to start an installation of HARD drive recovery.

  • A few questions about the Satellite A100 PSAANE

    Hi friends,

    I have a Toshiba Satellite A 100 - PSAANE with Vista Home Basic preinstalled in it.
    Now, I have a few questions... I mention below: -.

    (1) if I want to format my laptop, I need a CD to install for Vista Home basic... then I don't have this Toshiba CD when I bought the laptop. So how do? question: How can I format it?

    (2) can I change my Vista Home Basic to windows XP? I think it's much faster than this one. is it advisable?

    (3) I have a GB of RAM in the laptop. Increase the RAM? I think that my laptop has become to slow down. is it advisable?

    (4) and on my screen, everytime I try to change my profile screen to windows Classic view, my screen begins to blink. and after a while, the screen turns off. So I can't change that. I put the color scheme of windows vista only. What to do about that?

    Please help me friends. Thanks in advance.

    Kind regards
    Perkins

    Hello

    Here, a few questions about the number:

    (1) usually, you should get the Vista Toshiba Recovery DVD. If you didn t receive this DVD then you can order it here https://backupmedia.toshiba.eu/landing.aspx or you could install the disc of Microsoft Vista.

    (2) of course, you can do this. I think that Win XP drivers can be downloaded from the Toshiba driver page.

    (3) Yes, you can upgrade the RAM. For more information, see your manual or search on this forum for similar topics

    (4) maybe it s associated with the graphics driver. Check if you can update. I would recommend additional check if you are using the latest version of the BIOS

    Welcome them

  • Re: Several questions about the recovery of the Satellite L750 features

    I have several questions about the recovery of Satellite L750 features available to it. Any help and answers would be useful.

    (1) when I started the laptop first, he asked me to create a recovery CD incase I need to reinstall the operating system. But he also said that he built in the recovery partition, so therefore, I have to make a recovery cd or not?

    (2) will be the recovery CD is exactly the same as the recovery on the system partition?

    (3) is the partion of CD or recovery includes all the integrated software pre-installed with the laptop?

    (4) also in the device manage management it shows watch partion recovery but it is empty, is it true?

    (5) in the second partition (drive D) system, he has a record with what looks like the recovery of files and folders. Is it safe to move/remove it?

    Hello

    I'll try to provide answers:
    1 - to ensure that everything works perfectly you don t need these discs, but if something goes wrong with the HARD drive you will not be able to do anything. When you have the recovery DVDs, you will still be able to install the recovery image and once again the factory settings. So my advice to you is: create these discs as soon as possible. Use only on DVD-R media and buy products of high quality (TDK or Verbatim).
    2 - Yes.
    3 - Yes.
    4 - No. Don t be confused with this.
    5. in a first time create restore DVD, and later you can do what you want. I put t know which files mean you but don t touch anything before that of the recovery disks to be created.

    In the past, many people have been experimenting with the structure of HARD drive and partitions and later was surprised when installing disk recovery HARD has been damaged. Don t make the same mistake.

    If you have any other questions you are welcome.

  • Question about the new Yoga 10 HD +.

    Hello

    A few questions about the new Yoga 10 HD + that I hope you can answer.

    I bought the former model, last year. Love the design and long battery life, but a few major questions made me return.

    • Somewhere that I've read that it can not read NTFS on USB so I guess that's the same thing with a NTFS formatted microSD card?
    • Can it read exFAT formatted microSD cards?
    • Anyone who has questions about the audio via bluetooth?
      (I know that BT is not exactly High End HiFi but the old 10 Yoga for some obscure reason - most likely a driver problem which nobody cared to fix - rang * very * worst with visibly distortion while both my phone and a Tablet noname cheap I have zero about fidelity - any of my devices bluetooth audio) I tried aptX or not)

    So to avoid buying it back it also I really I would like to see if I can get my questions answered before buy you.

    While I love the form factor and long term issues above are only two Mayor dealbreakers for me. Bad audio quality = no joy listen to spotify, local etc. MP3s. not of NTFS or exFAT = some great movies.

    My old noname android Tablet really could use an upgrade so I'm really curious it may be, or I should watch the competition and will be form factor and battery LIFE.

    Thanks in advance.

    EDIT:

    If it does not support NTFS or exFAT on microSD card have someone at - he tried ext3 or ext4?

    I mean with Linux Android root, it should be a no-brainer to support at least when it comes to royalties unlike NTFS or exFAT where it * might * have some trouble with Microsoft.

    I used a USB through a USB OTG cable. NTFS or exFAT have been recognized by the Tablet PC. FAT32 is seems to be the preference.

  • I have a question about the time machine. I recently updated my Quicken 2015 and there was something wrong with the update. Can I go back in just the Quicken file and restore it until I downloaded the update do I have to restore the entire

    I have a question about the time machine. I recently updated my Quicken 2015 and there was something wrong with the update. Can I come back in all the Quicken file and restore from time Machine before I downloaded the update to do, I need to restore the entire computer?

    Yes, you can just restore this file or application. Use Time Machine to back up or restore your Mac - Apple Support

  • Just a quick question about the appearance of the cluster

    Hello, this is Matthew, just a quick question about the appearance of the cluster

    Is there anyway to rearrange the order of the elements? I know cutting automatic resizing, I could move the items by hand. But if I use the cluster somewhere else, I have to move the items again...

    What I want is of the order of "Mx My Mz Ax Ay Az Temp voltage CS".

    Is there a quicker way to deal with?

    THz so much!

    You can right-click the border of the cluster and choose "arrange control cluster...". "The user interface is not as intuitive as it could be, but it will allow you to reorder items. If you use the cluster in several places, you should make the cluster in a type definition and replace all current uses of the latter with the type definition, so that they all match. They will also update automatically when you make changes to the type definition. Otherwise, you could have a situation where you have multiple groups with the same data types, but with elements in a different order, and your data will be getting a new denominated, when wire you the whole clusters. The data will be in the same order, but given that the item labels are in a different order, you can't get the data you want, when ungroup you by name.

Maybe you are looking for