Question of 2012 R2 install Poweredge R415

I have my SAS drives in a RAID 5 (PERC S300, Poweredge R415) matrix and also appear online. When I go through the lifecycle to deploy Server R2 2012 he does not see the drive to install the operating system to. I tried to load the driver retrieved through the USB port, but it happens to say that there is no available signed drvier. Can you tell me to fix the driver should I use?

Rah33,

Unfortunately the S100 and S300 raid controllers do not have support for Microsoft Windows Server 2012 and there is currently no plan to support these controllers with Microsoft Windows Server 2012 in the future. If you use the S300 controllers, you must either get the controller hardware raid (h700), or you would need to follow this procedure to continue.

  • Open the server and remove cables internal SATA connected to the S300 controller and connect it to the embedded SATA controller of the server ports.
  • Power on the server and press F2 to enter the BIOS settings.
  • Enter the--> SATA settings BIOS setup and change it to ATA or ACHI mode depending on what is available. See Figure-1.
  • Save and exit the installation program.
  • Boot from the DVD Microsoft Windows Server 2012 and proceed with the installation
  • You can learn more about this here.

    I hope this helps to answer your question, even though this is probably not the answer you wanted to hear.

Tags: Dell Servers

Similar Questions

  • Install HDD PowerEdge R415

    Hello!

    I recently bought a Dell PowerEdge R415 with the following specifications:
    AMD Opteron 4180 - 2, 6 GHz / 6.4 Gbit / s (top Six)
    8 GB DDR3 ECC RAM
    AMD SR5670 and SP5100 chipset
    PERC H700 Raid Controller
    iDrac 6 Express & Enterprise
    R2 Windows Server 2012
    Kingston 128 GB SSD

    Now, here's my problem:

    I initially intended to use as a storage partition 2 x Seagate Barracuda 3 to hard disks in RAID 1, but while windows detects their size it is partition 2 TB on them. I thought pole H700 would be able to use 3 TB disks. I was wrong? And also on Dells site it indicates the maximum capacity of PowerEdge R415s is 8 TB is true, or you can run 4 x 3 TB drives in there?

    PERC H700 can use drives of capacity greater than 2 TB. R415 maximum capacity is 8 TB + (the only reason it lists 8TB is because that was the maximum based on the largest drives Dell tested/validated at time of writing you found). Current data sheet shows 12 to:

    http://www.Dell.com/downloads/global/products/pedge/spc_r415_new.PDF

    The problem that you run is with the operating system:

    • Windows cannot use a more 2 TB drive unless it has been converted to GPT.
    • Windows cannot start on a GPT disk, except if it is installed on a UEFI system.

    So, you can either 'slice' the RAID by creating several bays on the disks, with less than 2 TB 'disc' boot, or you must enable UEFI and reinstall the OS in this mode (conversion of GPT is data destructive).

  • Why (Preview Developer 64-bit windows) prevent Kaspersky 2012 to install internet security

    Why (Preview Developer 64-bit windows) prevent Kaspersky 2012 to install internet security...

    First of all, this forum is for posting comments on the web site of Microsoft Answers, is not for technical questions.  Secondly, this is not the place to ask questions about WIndows 8 Developer Preview.

    Some likely forums are:
    http://social.msdn.Microsoft.com/forums/en-us/category/windowsapps
    http://social.msdn.Microsoft.com/forums/en-us/windowsdeveloperpreviewgeneral/threads
    http://social.msdn.Microsoft.com/forums/en-us/category/windowsdesktopdev

  • I use windwos xpsp3 teacher, my question is wn I install winxp after 6 months my hardware (motherboard) will be too bad so I'll be changed motherboard so I can use my OS still this material, I've heard could not appu .so wy use winxp.so me.pls help

    I use microsoft Windows xpsp3 teacher that my question is wn I install winxp after 6 months that my hardware (motherboard) will be too bad so I'll be changed motherboard so I can use my OS still this material, I've heard could not appu .so wy use winxp.so me.pls help

    You can reuse your current XP only if the version is not OEM.  OEM is a version that must be supported directly by the manufacturer of the computer first.  OEM is always linked to the first PC, the license is activated on.  This license is suppused to 'die' with the PC.  Now, there is a "grey area" on the definition of a PC, but accepted the more common definition all came to the conclusion that the 'mother' is the building block for the definition.  Therefore, change of motherboards would mean you have a "new" PC

  • I bought photoshop in 2012 and installed on the mac, I had then. I lost the disc and need this computer. How do I install it on my new computer. Any help would be greatly appreciated. Thank you. Josh.

    I bought photoshop in 2012 and installed on the mac, I had then.  I lost the disc and need this computer. How do I install it on my new computer. Any help would be greatly appreciated. Thank you. Josh

    I hope you find the serial number... but if not, it may be worth mentioning that you can use Photoshop and Lightroom for $9.99 / month. It's a big dea; : Lightroom and Photoshop | Plan of creative photography of cloud to Adobe .

  • Installation of windows 2012 R2 on Poweredge R900 with Raid

    Hello

    I have installed Windorws on my Poweredge R900 2012 R2 there controller raid Perc 6 / I with 5 SAS 300 GB HARD drive, but I don't know on what level of raid, the operating system installed. When I check the drive C: Manager shows 790 GB but as a virtual disk Dell watch TB 1.35 approx. might one explain what the level of raid, the operating system is on and how to check it.

    Thank you

    If you have 5x300GB disks in a RAID array, and the total size of the array is ~1.35TB, you can have them in a RAID 0. Click on the RAID 0 to see the Member disks - you will probably see that a single disk virtual, you will probably see 5 records as members of this VD, and you will probably see 0 GB of free space on each.

    Then, C: is 803GB... What other partitions are there?

    In RAID 0, if a disk fails, EVERYTHING disappeared. You're almost certain to have a loss of data. I would recommend you get a backup, wipe your RAID 0 and set up a larger RAID 5 (or 6 would be better).

  • GPU-installed PowerEdge T630

    My Adviser has recently bought a server PowerEdge T630 and we want to install NVIDIA Tesla K40 in the future. It has a dual power supply plug-in to warm 1100W. He ordered without a GPU installation kit.

    I was going through one of the Q & as where it was said to a GPU activation kit.

    My question is when we buy a NVIDIA GPU then what do we need to install it? It should be straight forward?

    Thank you much for the help.

    Sumana

    As I understand it, the GPU installation kit must be selected when the system is ordered. In this way, the required components (auxiliary power GPU, power distribution Board, cable etc) that allow to install GPU cards are included with the server.

    Note that if the system does not have GPU installation capabilities, then the unit must be returned and need to order a new unit with the desired GPU installation capacity.

    Also note that even if the order Dell T630 page provides an option for a GPU enablement "kit", there is no such package that can be ordered post sale. He calls a "kit" gives a false impression that a kit really exists, that it is not.

    Either Dell should change the wording on its order page to clarify, it isn't a kit as such GOLD go down his back and actually a kit that can be used to update the T630 for GPU cards to install (if it has not ordered with such capacity).

  • Quick question on Version after installing the Patch Bundle

    Hello

    This is my setup

    O/s: Victoire 2012 Stnd. edition

    DB: Oracle 12.1.0.2

    I installed bundle Win patch 12.1 . 0.2.11 via patch 22005474 on my PIC and PDB.

    I checked it via Opatch lsinventory and executed following on the CBD sql as PDB for to ensure that the system reflects that the correction has been installed.

    The CBD

    select * from dba_registry_sqlpatch;
    

    Patch_CDB.PNG

    On PDB

    select * from dba_registry_sqlpatch;
    

    patch_pdb.PNG

    So my question is very simple, when I ask instance of $ v, should I wait 12.2.0.11 instead of 12.1.0.2.0 in the VERSION column in the instance of $ v just because I installed this patch bundle?

    select * from v$instance
    

    instance.PNG

    -Learner

    Hello

    It would be same 12.1.0.2.0

    -Pavan Kumar N

  • Question seeks to clean install 10 Windows on the drive of the merger. El Capitan.

    Problem: try a clean install of Windows 10 via the Boot Camp Assistant on an iMac 27 inches (Late2013) with 10.11.4 installs hours (more than 8 hours) and then failed to install Boot Camp updates. Essentially installation take much long than normal and cannot install updates of the Apple software or create normally start Windows Boot Camp 10.

    Background: After problems of slowing down after upgrading to 10.11.4 (with improved Bootcamp Windows 10) who had previously worked fine for 10 months, to the point of a start of OS X time, I decided to do a clean install of my iMac with Fusion 3 to disk.

    As I was unable to remove the partition from Boot Camp through BCA because of his holding always at the same load, I used Internet recovery and reset the Fusion drive. This then required me to repair the partition of Fusion by car through THE "fix" option which seems to work very well. And reinstalled OS X 10.11.4 which works fine now (delays etc..)

    Try using BCA to create a new partition Boot Camp and a clean Windows 10 install after downloading an image of disk W10 directly from Microsoft (Win10_1511_1_English_x64), BCA by downloading software updates and by selecting the desired partition, it began to restart and initialize the installation. However the whole process has been very slow, each step takes much longer than usual, to progress. Leave for hours rest a blank screen or with a circle of rotation.

    I tried with another stick USB 3 and also a USB 2 stick, but none has made a difference.

    In the last attempt, I left running overnight and after 8-9 hours, he finally reaches the top of desktop Windows 10 and the update of Apple Bootcamp starts to load updates. However, he just hung and even after 2 hours, nothing was. Reboot and try once again has been the same.

    After that I tried to create a Windows Installer via BCA 8.0 however it gives just a TPG error when you try to select the drive (due to el Capitan I guess?)

    After four days of efforts, I'm a loser on how to get the Windows 10 on the Boot Camp partition. I can't even install W8 and upgrade due to the error of TPG.

    Any help or suggestions how to proceed with the diagnostic / resolution of the problem would be appreciated.

    Details:

    System: iMac (27 inch, end of 2013), 3.4 GHz Intel Core i5, 16 GB 1600 MHz DDR3, NVIDIA GeForce GTX 780 M 4096 MB, OS X 10.11.4

    • Nothing other than the keyboard and mouse attached via the USB ports, as well as the key USB of BCA. No other attached devices.
    • Reset memory NVRAM, SMC and ran more than once disk utility. No problem not reported.  Ran NVRAM reset before each attempt.
    • At ran EtreCheck report which seemed OK.
    • Verification of diagnosis ran who is childless.

    A detail I noticed after the merger by car there are now two Macintosh HD images when you use boot option. One previously. Are named "Macintosh HD" and "Macintosh HD2". I remember being Yosemite simultaneously in three, but which has been fixed in an update.

    In addition, it seems that no recovery partition. Cmd + R lance Internet recovery.

    Distill the results (the Boot Camp partition removed):

    / dev/disk0 (internal, physical):

    #: NAME SIZE TYPE IDENTIFIER

    0: GUID_partition_scheme * GB 121,3 disk0

    1: disk0s1 EFI EFI 209.7 MB

    2: Apple_CoreStorage GB internal drive 121.0 disk0s2

    3: disk0s3 Apple_Boot Boot OS X 134,2 MB

    / dev/disk2 (internal, physical):

    #: NAME SIZE TYPE IDENTIFIER

    0: GUID_partition_scheme * 3.0 to disk2

    1: disk2s1 NO NAME 209.7 MB EFI

    2: disk2s2 Apple_CoreStorage TB 3.0 drive internal

    3: disk2s4 Apple_Boot Boot OS X 134,2 MB

    / dev/disk3 (internal, virtual):

    #: NAME SIZE TYPE IDENTIFIER

    0: Apple_HFS Macintosh HD + 3.1 TB disk3

    Logical volume on disk0s2, disk2s2

    7BE1F343-ACBE-4144-BF86-C838BE1E49D4

    Fusion unencrypted drive

    iMac - simon: ~ list of cs simon$ diskutil

    CoreStorage groups of logical volumes (1 found)

    |

    + Logical Volume - Group CA0B8D0A-6315-4E85-B313-52AB509473F2

    =========================================================

    Name: Internal drive

    Status: online

    Dimensions: 3121237860352 B (3.1 TB)

    Free space: 0 (0 B) B

    |

    +-Physical volume 5E75EE74-EE1F-4FCB-A0C5-9ED5517FEB93

    |   ----------------------------------------------------

    |   Index: 0

    |   Disc: disk0s2

    |   Status: online

    |   Dimensions: 120988852224 B (121.0 GB)

    |

    +-Physical volume 91D639D6-634E-47C1-AFE5-616CE12E71E0

    |   ----------------------------------------------------

    |   Index: 1

    |   Disc: disk2s2

    |   Status: online

    |   Dimensions: 3000249008128 B (3.0 to)

    |

    +--> Logical volume family EE9934AC-F3CB-4101-ADB6-576F4371B4B9

    ----------------------------------------------------------

    Encryption type: no

    |

    +--> Logical volume 7BE1F343-ACBE-4144-BF86-C838BE1E49D4

    ---------------------------------------------------

    Disc: disk3

    Status: online

    Size (Total): 3106705375232 B (3.1 TB)

    Reversible: no

    Name: Macintosh HD

    Volume name: Macintosh HD

    Content indicator: Apple_HFS

    LVG Type: Fusion, sparse

    Summary:

    Q1: Should it take 4 + hours to install Windows 10 via BCA?

    Q2: Al must ultimately be so slow when initially W10 desktop?

    Q3; What I do once I arrive at the office of W10 but it automatically updates the graphics driver as BC update is simply suspended for centuries and get a working driver to restart at least W10?

    Q4: is there a problem with the disk HARD the Drive of Fusion that is causing all this delay and slow install / boot? ON the clean install OS X 10.11.4 it is back to be fast as usual and all tests show things are OK but W10 goes on the part of the HARD drive. No way to verify this beyond diagnosis or Etrecheck?

    Q5: Y at - it no problem with the GPT / MBR that may be causing the delay etc. ?

    Q6: How can I use my existing WindowsImageBackup backup from the previous W10 with the BCA install usb drive or how to create a USB stick otherwise recovery disk with my other single Mac have W7?

    Q7: How can I install W8 as I once did on Yosemite, via el Capitan without a mistake to TPG on selection of disc?

    Details:

    Day 5. Attempt at 6.

    Partition Boot Camp delete and try again install via BCA. First question, is that when the startup it goes to a blank black screen. For a time nothing left. Reset then using alt to select windows training results in almost instantaneous startup of the BCA message created and the beginning of the installation.

    4 1/2 hours from start of Windows 10 initial signature window.

    Then the second question. One to reach the Boot Camp update Office tries to start and install the drivers. Allows you to "list files...". "stage then sits at the bar about 5% green for 1 to 2 hours and does nothing. All actions in the Office of the W10 takes ages.

    In the meantime, auto update of the W10 appears a message saying that the updated graphics drivers as one of the few messages or actions during this period. Looks like Nvidia install with the entire package of experience (unwanted) etc. and very probably not the correct gpu driver.

    Finally deciding to cancel the installation of BC by killing the Setup.exe process. Then copy Boot camp install files on the desktop. Lasts 30 minutes to copy. Run again and this time, although taking 15-20 minutes to download and install later with the success message.

    Check the graphic driver it shows a yellow exclamation mark, so the following Microsoft instructions I use the uninstall option via the device and then Manager (slowly) come on board to load and download the latest Nvidia driver on their site for the GTX 780 M for 64-bit W10 etc. The same thing that I had used previously. Slow with running the Nvidia Setup program again, but eventually it works only to say that he could not install as unrecognized graphics device...

    He ends up with Microsoft PnP driver so it's at least sufficient start and run it again BC of the figure updates as all other drivers have been installed. To restart, but I get an error of K-Mode that is most likely related to this driver graphic and not possible to start in the new W10 Boot Camp partition after 7 hours.

    I have a picture of W10 backup recovery (WindowsImageBackup) I've had in a few weeks, but it will not install bet for the installed W10. I try with the ACO created the USB windows but can't seem to get a way to get into recovery mode and to get the menu to install it. I don't have a way to create a USB W10 recovery key now because my other Mac has just installed W7.

    Finally I tried to count a reset of the Recovery boot up option but it seems that it will take longer to start.

    I also went to the recovery and selected Boot Mode safe, but it opens on an empty black window and he's here doing nothing.

    Looks like I'll have to restart on via BCA and reinstall and try and solve the problem of graphics in order to install driver updates from BC and restart to W10 and hope that with the drivers, it returns to the operation and the normal starting time. Then update the gpu driver.

    I used and installed Boot Camp several times with over the years including previously an upgrade of W8.1 > W10 I used for over 6 months without problem. I've never known these installation very long or ice once in Windows even for the initial start upward.

    For any help or suggestion would be appreciated, and this seemingly simple process has now expanded to five days.

  • Windows Server 2012 on Dell PowerEdge R610

    Hello-

    Anyone know how to upgrade R610 so that I can install 2012 from the BIOS?

    I tried as 'other' to F10 and it failed with pilot errors. I tried to update the firmware with the management of the ISO and the same thing happened.

    Is there a method I'm missing?

    Thank you

    Prince

    Princesly,

    The R610 takes in 2012. You tried to start directly on the support of 2012? Looks like you were trying to use a Dell OS installation disc.

    What happens when you start Media?

    Also, have you tried to install it using the lifecycle controller (F10 on screen Dell)?

  • Impossible to get any OS to install PowerEdge 1750 Server

    I'm having some trouble with that and it makes me nuts. It's the 1st Rackmount Dell I worked on. Other then that I was working on a tower. But the part that I did not do anything with the SCSI hard drives is.

    So maybe someone here can help me. I got a Dell PowerEdge 1750, 2 Maxtor 36 GB SCSI disks in there. The server was using RAID mirror the primary drive before being erased and replaced. So now, the server must be configured with Linux and it does not matter if drivers are reflected in the RAID at all.

    So I tried to install Ubuntu server OS and he repeated to me that it cannot find the drivers for the drives. I tried a few drivers here at DELL who have been to Red Hat and it did not work.

    Then, I tried a copy of Red Hat Linux 8.0 and had the same problem that Ubuntu has given me.

    Then laughing, I tried a copy of Windows XP Home Edition who was sitting by a former Workstation. Same problem, Windows could not find the hard drives. I have download the drivers PERC 4/Di windows server 2000 and 2003 (x 84). Tried loading to see if pilots would allow me to install the OS or not. Never worked.

    Finally try, I popped a copy of Windows Server 2003 R2 Enterprise Edition in and he had the same problem as XP, so I pop the drivers PERC 4/Di and selected the driver for Windows Server 2003 and it has yet to find the hard drives.

    What I am doing wrong?

    NEWS POST:

    Integrated server 1.80 Firmware revision management

    Review from the primary backplane Firmware 1.01

    PowerEdge Expandable RAID Controller BIOS B109 February 18, 2003

    PERC 4/Di Standard FW 4.04

    0 logical drives to the host adapter

    Or logical drives 0 managed by the BIOS

    Broadcom NetXtreme managed by BIOS Boot Agent V7.0.3

    I don't know if this noraml or not, I think that it funny that he finds the 0 logical drives, but when you go into the configuration both appear in there.

    PERC does not support non - RAID JBOD, so if you want mirrored or not, you must configure the drives in the PERC BIOS (CTRL-M)... or put it turns off and only use the system SCSI controller.

    If you want to use as separate readers readers / person, you must configure each disk in a single drive RAID 0.

    If you want to disable RAID and used in SCSI mode only, so you need to start on the configuration of the BIOS (F2), embedded devices, and Embedded RAID SCSI value active.

    The fact that the POST said 0 logical drives found indicates that the disks are not configured - don't forget, readers must be configured in a sort of table before they can be used by the operating system.  So it must show at least a logical drive before installation can never be successful.

    Once the RAID is set up, you will need to worry about drivers.

  • Question about web access install

    Hi all

    Can you please help me answer this question.

    setting up web access on VC is optional or not? as far as I can see, Web access is automatically installed with VC. all you need to do is specify ports, but after reading this text on web access pdf Pub, now I confused.

    -


    VI Web Access is installed when ESX Server is installed. On the VirtualCenter server, you

    can install VI Web Access from the VirtualCenter Server Windows installation package

    -


    I tried my self installation of VC but I have not any Web Access option select/deselct option

    Please clarify this point for me

    Thanks in advance

    AJ

    Hi all

    Question of Ajay on access Web is a good thing, let me clarify.

    Components access Web are automatically installed with ESX Server and vCenter Server.  At some point in the history of the product, there is an option during the installation of VirtualCenter, where you can choose to install Web access or not.  This is no longer the case at 2.5 or 4.  Web access is also enabled by default previously.  In my last use of the product, I find that the service on vCenter Server is already started, which means that Web Access is running by default.  For ESX Server, the access to the Web server is not running, but can be easily launched.  It's for vSphere 4, so fellow users, you can add what is the default status VI3 if you run this version of the product, so we have that here as well.

    Kind regards

    Jon C. Hall

    Technical developer certification

    VMware, Inc..

  • PowerEdge R415 - external SCSI tape drive?

    I was looking through the updates available for the R415 find a scsi interface card. I do not see an extra, but was hoping someone could point me to a compatible card. It is necessary to connect to scsi tape drives.

    Oly_R,

    The adapter you need is the LSI 2032. As long as found on page 9 of the R415 technical guide - http://www.dell.com/downloads/global/products/misc/r415_tech_guide_11_18_10_final.pdf

    The LSI2032 part number is NU947.

    Let me know if that answers your question.

  • Satellite Pro P100 Question on software pre-installed

    I bought a Toshiba laptop in July and although I am very happy with the machine.

    I'm very upset that he came with very little software that I expected at least MS works or similar for a professional laptop, but there is nothing (no spreadsheet, text or data processing)

    After spending more than £1,000. I'm a little annoyed - don't know if it's a world of Toshiba or PC Business (people, I bought it from) error.

    One of my colleagues bought a laptop the week £600 last and which have very many useful software pre-installation.

    Hello

    You talk about the Satellite Pro P100 PSPA4E series?

    If you really this machine then I put t agree with you!
    To my knowledge of many tools and utilities and additional programs have been installed on this laptop.
    Maybe a small list?
    Here you are:
    -Office OneNote2003
    -TOSHIBA utilities
    -WinDVD
    -Platinum WinDVD Creator2
    -Sonic DLA
    -Symantec Norton AntiVirus 2006
    -PC Diagnostic tool
    -Etc.

    Please note that the software package Microsoft Office OneNote offers several useful simple programs!

    May I ask why you compare one satellite Pro P100 with other laptops who don t support the same processor, the graphics card performance and additional features?

    From my personal experience of many manufacturers of laptop while customers with software pre-installed because that the performance of the laptop or simple parts (graphics card, HARD drive, memory IE) are not approximately the same mostly.

    Last but not least; I put t really understand why you're a little annoyed.
    Why you didn t check the laptop and the description?
    Do you always buy a cat in a bag?

    Really strange guy?  :|

  • Satellite P200 - 17 c: Question on the clean install of Vista

    Hello

    I have the Toshiba P200 - 17 c Personal Computer and I don't want programs like Norton ISI because I want to install my own I, so thought to format the drive to install Vista Premium on its own and then install the drivers and the utilities of the download on the Toshiba webssite section, but, after reading the thread at this link :

    http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=28091&TSTART=45

    I see that some users who also have this pc had problems to install the drivers and utilities, that they got on the site for their P200 - 17 c. A user who installed instead of Vista Premium Professional Vista and then tried to install the drivers/utilities for Vista Business that he has downloaded from toshiba and was getting errors like "invalid serial number."

    I still want to use Vista Premium on my P200 - 17 c and then install my Toshiba approved some drivers/utilities. Surely in this case, all the drivers should install without problem on the same model computer and s/n?

    Concerning

    Brave

    Hello

    The European driver Toshiba page provides the drivers for Vista OS. This means that these drivers must be compatible with all versions of Vista. There should be no problem because all the Vista OS s use the same kernel!

    But note; If you use the clean Vista you must also use a compatible serial for a Vista version right key. In addition, you should note that there are different sets of P200 and so good drivers for the series on the right should be choose in download form.

    All that s

Maybe you are looking for

  • Satellite A660-07 s - how to fix ERROR 6006 DAE

    I have a music system Digidesign 003 Rack, it is a product of AVID.I need the software Protools 8.0.4 for this. I recently bought a Toshiba Satellite A660 07 s with geforce GT 330 M graphics card and windows 7 o/s.I installed the 1394 to firewireport

  • formula node

    I send it a zone indicator shows full decimal form but receive and whole. I changed the data types of the double room on long extended float etc, with no result. Y at - it something I am doing wrong?

  • number conversion chain

  • Content not lining up

    Can someone tell me why this is happening?< ! DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional / / IN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd" > """ < html xmlns =" http://www.w3.org/1999/xhtml ">< head >< meta http-equiv = "

  • The challenges network - welcomed the ideas

    Hello I have an Officejet 7410 currently connected by usb to my office main office running Windows 7 - everything revolves slowly. My first challenge is to add the ability to print for a laptop I take London - based Vista already has a connection to