question of ddr3 OptiPlex 780

Hello world

I just bought an extra ram for my dell optiplex 780 (DT), which is the Dual Channel DDR3 Corsair Value Select, 2 x 2 GB PC3-10600, CASE 9

Once inserted, (tried it with permutation of the modules - just one and the banks swapping) no way to start, just a terrible sound of the ringing ^^

question: is this ram modules compatible with this computer?

BTW, I discovered that "it must be" according to the website of kingston (on which you select your computer and it says you which modules are for you ^^)

Thank you!

Claude

Hi Claude,.

Welcome to the Dell Community.

Your Dell Optiplex 780 supports DDR3 memory, but the memory speed, it supports is 1067 MHz (PC2-8500). The modules of memory that you have purchased speed of 1333 MHz memory, and unfortunately they are not compatible with your computer.

Please, contact the supplier for memory, replaced by 1067 MHz modules.

If you have any other questions, feel free to respond.

Tags: Dell Desktop

Similar Questions

  • Dell Optiplex 780 memory update does not

    1. I have purchase Dell Optiplex 780 supplied with memory DDR3 8 GB (4x2Go). I wanted to update so I bought 4 GB RAM (4x1Go) and tried to install it today. The diagnostic lights Dell on 3 and 4, which means that the memory is detected, but at fault. Now, I doubt that this new module of memory are defective. Here's what I did to solve problems:

      I took the original strips and installed a new. There are 4 DIMM and I tried to put it in all the 4 connectors DIMM one, but my PC will not start and shows the Dell diagnostic lights lit 3 and 4. then I put my original RAMS but still the same problem has happened that I also tried the two Rams Original one by one in all the slots but same question :(

      I also tried without installed memory but still Dell lights lit diagnostic 3 and 4 and no beep heard.

      Can someone help me what is the problem real?

    Hi Danish_smartpk,

    Welcome to the Dell Community Forum.

    If the 3 and 4 diagnostic lights are lit, it is code modules of memory detected, but a memory failure that occurred. You also mentioned that there is not only no beeps no heard when no memory is installed. When no memory is detected by the system, it emits beep codes indicating the same.  If the motherboard is not beep when no memory is installed, it could indicate failure systemboard.

    It is generally recommended that the BIOS updated before the new memory being installed. In addition, your computer supports a maximum of 8 GB of RAM DDR3 SDRAM (memory non - ECC only). If it already came with 8 GB of memory, it would not take an additional upgrade.

    If the system is under warranty, contact me with a message private by clicking on my name highlighted in blue. On the next page, click on the envelope icon and provide your service and coordinates (as mentioned below) so that I can access your system folders.

    • System Service Tag No.:
    • Name of the registered owner system:
    • Shipping address:
    • Number of phone/s:
    • E-mail address:

    However, if the system is out of warranty, you can contact a local technician for assistance to the replacement of the motherboard or contact our warranty Support has expired on the link below:

    http://Dell.to/12LmNBq

    Please do not hesitate to contact us in case of other queries.

    Thank you and best regards,
    Babita S
    #iworkforDell

    For easy access to the drivers, manuals and updates, please visit ourSupport Site .

  • Three Options for Optiplex 780 follow-up?

    We have about 25 users who need 3 monitors for monitoring systematized and real-time data analysis. These users do not enter our requirement of workstation group. IE, they came away who need the performance of a workstation availability, although the need for the three monitors.  If it is difficult to justify one for their needs.

    I hope it has a healthy option available to provide any Optiplex 780 and 760 users with support for three monitors. I must point out, these are the models of office, the second most available small, who is probably the choice that much more limited. Currently we run the standard ati DVI and the adapter y - vga allowing them their two monitors. If we add a second video card flat with vga connector, the system would allow the three monitor is to be active? (windows xp and windows 7). I don't see a low profile card that would allow two monitors off the dvi (vga y adapater) more a stand-alone vga.

    Recommendations on how to do this without a rip and replace it?

    Thank you guys!

    Not looking at the whole picture.   DMS - 59 to two DVI has 2 outputs.  Out of each DVI DUAL LINK is the sense it has a DVI - D and DVI - A so he can do 1 digital and 1 VGA monitor with the 2nd cable Dell.     If you use 2 cables with 2 outputs DVI - A, you get 4 monitors.

    The other card more expensive that I linked has 4 DVI connections.

    Does not seem to you look at the links however to make me wonder if you're just a bot posting endless questions.

  • (Redirected) GPU that will work with my dell optiplex 780

    Hello. I recently bought a dell optiplex 780 desktop computer (DT). I want to increase the power of the GPU, but I don't know what are the options I have or what I can get. I mainly play minecraft and MMORPG games. Does anyone have suggestions for me to be able to get without breaking the Bank or buy a new power supply? If you could help, I would really appreciate it. Thanks again.

    Data sheet:

    CPU: Intel Core2Duo E7600 (3.06 Ghz)

    RAM: 4 GB (I don't know if its DDR2 or DDR3)

    GPU: Integrated (it seems an Intel GMA 4500)

    OS: windows 7 (64-bit)

    link to the PDF of the dell optiplex 780 (the one I have is the desktop Dell Optiplex 780 (DT)

    www.Dell.com/.../optiplex_780_tech_guidebook_en.pdf

    Hi R3DSTON3R,

    Please repost this in the forum Office help.

    http://en.community.Dell.com/support-forums/desktop/

  • Dell Optiplex 780 compatible graphics cards?

    Hi all I'm new on the dell forum. I love my Dell Optiplex 780 SFF and last year I bought a

    "Sapphire AMD HD6570 2 GB DDR3 Lite Retail PCI-E graphics card" which worked but was too big for the case.

    Now, I am looking for the best compatible graphics card, I saw in another post that the Sapphire HD 7750 Low Profile fits, but is there something better than that, that fits and is not low profile?

    CoreSci

    Hi all I'm new on the dell forum. I love my Dell Optiplex 780 SFF and last year I bought a

    "Sapphire AMD HD6570 2 GB DDR3 Lite Retail PCI-E graphics card" which worked but was too big for the case.

    Now, I am looking for the best compatible graphics card, I saw in another post that the Sapphire HD 7750 Low Profile fits, but is there something better than that, that fits and is not low profile?

    First, ask yourself "is there something better than that, which corresponds to and is not low profile?  No, because there ONLY cards that will fit must be small footprint!

    Second, 7750 HD cards are often recommended as a good choice for the Dells - unique slot and low power requirements.  I am running a 7750 HD in my own 780 MT, having chosen as the best choice for fit and performance.  That said, your power supply of the SFF is only 235W, which is very marginal.  I've seen reports of others by means of this type of card in a 780 SFF, but you should make sure, that it is not overtax the power, depending on what you have in your computer.

  • Upgrade to 4 GB Ram problem - computer desktop OptiPlex 780...

    Nice day

    Thank you for your services.

    I am trying to upgrade my desktop computer model # OptiPlex 780 and it's the standard I force the affected elements before, after I check what is the speed of compatible ram, voltage and timing, then I bought this model:

    KHX1333C9D3B1K2 / 8G

    Sound of Kingston - hyper-x blue or you can check the details by the Munificent code above or visiting them this link:

    http://www.Kingston.com/datasheets/KHX1333C9D3B1K2_8G.PDF

    The problem:

    When I delete the original 2 GB Ram and installed this 4 GB ram on the first location, the departure of light 1 # & 3 led with sound as continuous hum without starter or windows interface.

    I tried to:

    -Change the slot

    -Fix the maximum ram which is 4 GB for each slot up to 16 GB

    -Correction of the original 2GB ram in slot 1 then fix the new ram in slot 2 or 3 and 4

    -Update the BIOS to version 15A and update all the drivers from dell.com

    -I make sure that the ram is compatible Guide Dell book on this link:

    http://i.Dell.com/sites/content/business/solutions/engineering-docs/en/documents/OptiPlex-780-tech-guide.PDF

    So please help me in this case, it is urgent and I used this computer in the main office and my work.

    Thanks and regards,

    BYQ-

    svanwormer

    I have a 780 with the Intel E7500, Q45 chipset and A15 BIOS CPU and I'm running 12 GB of DDR3 RAM. Two 4 GB and 2 GB

    Yep, catilley, I'm afraid, you're just wrong on this point - your info is old, apparently.  I, too, running an Optiplex 780 with an Intel Core 2 Quad 9550 CPU, chipset Q45 and 12 GB of DDR3 memory - in fact, it's the same machine that I write this response at this time.

    As I posted a year ago on this thread, the official manual of Service from Dell for Optiplex 780 confirms it will take up to 16 MB of memory DDR3, 4 GB per slot.  Here is the link, directly from the Dell website:

  • Need video driver Windows 8.1 Overview for Dell Optiplex 780

    Hello

    I installed windows copy 9431 build Preview Pro Windows 8.1 evaluation (64-bit). I tried all video drivers http://www.dell.com/support/drivers/us/en/04/Product/optiplex-780 for Windows 7 64-bit.

    But no driver is compatible with my windows. Single driver installed successfully named "VideoOPGA6_XP_A00_setup - R3M7Y_ZPE.exe", but does not properly. Can U please give me the link of good pilot?

    Problem is only with the video driver.

    My whole PC details:

    Processor: Intel Core 2 Duo E8400 @ 3 GHz 2.99 .00GHz

    Hadrdrive: 640 GB Seagate

    RAM: 12 GB (4 GB x 3) DDR3

    I am waiting for your kind reply.

    Best regards

    Danish Muhammad

    Hi Muhammad Danish,

    Windows 8 compatible drivers for OptiPlex 780 are not available on the Dell support Web site.

    Have you tried to check for drivers on the video card manufacturer's website? Based on the file name of drivers you mentioned, I think that your computer is the AMD Radeon HD 3470 graphics card.

    Try to install more software Catalyst from the following link: http://dell.to/16zWqy5

    Do not answer with the results.

  • Upgrade memory OptiPlex 780

    I bought 2 x 4 GB memory to update my 780 Optiplex originally shipped with only 2 GB. I did some research to make sure that memory, I buy would be compatible with the motherboard. I bought the next memory at amazon:

    www.Amazon.com/.../Ref=oh_aui_detailpage_o00_s00; PSC = 1

    When I put in the new memory, the PC starts normally, fans work and everything, but I have absolutely no video signal to my monitor. When I appear in the old 2 GB, the computer starts normally and I can use it.

    Can you please indicate how do the new memory works, if I have to go into the bios?

    Thank you in advance.

    Then I understood the question, I had to upgrade the Bios A15 and then as soon as I installed the new glue 2x4gb Optiplex 780 automatically their picked up and worked perfectly.

  • No tengo sonido en mi dell optiplex 780 tengo wxp

    OLA me lla mo I have a dell optiplex 780 migue y lo muestra in el ordenador no audio rreproduce me pueden decir como instalo el driver of pc audio mid

    Advanced: http://www.dell.com/support/drivers/us/en/19/DriverDetails/DriverFileFormats?DriverId=R282894&FileId=2731115123

  • OptiPlex 780 MT power

    Is it the right kind of food for the above system?

    We have never sold the OptiPlex 780 MT with a power supply 500w (power supply)? Here is the block of power SUPPLY Dell OEM 305 w validated for the OptiPlex 780 MT =
    18N8R
    CY827
    MK9GY
    PF3TR
    P192M
    M360M
    WU133

    Simply do a search for each number of the piece like this =
    Reference Dell part 18N8R

  • OptiPlex 780 A15 Bios error 2 and 4

    It seems that every Dell Optiplex 780, version minitower, 0C27VV motherboard that I saw that was updated BIOS version A15 poster code error 2 front and 4 on reboot.  They do, however, start ok to power.  Why isn't it posted anywhere?  What is the solution?  How the BIOS can be reversed to say, A12.  Otherwise, this is a great computer, just make sure you do not update the BIOS A15.

    Dale al.

    [Admin note: personal information]

    My apologies, RoHe, that's what you're missing.  The monitor is connected to the computer via a KVM Linkskey switch.  When the monitor is connected directly to the computer, the problem disappears.  Thank you for your time.

  • Add the second hard drive in the Dell Optiplex 780 SFF

    Hello

    I have dell Optiplex 780 SFF (Small Form Factor) PC. It has 3 options of SATA. I want to add 2nd hard drive in it, but I see no power for 2 hard drive cable.

    At the present time, I have a SATA Hard Drive and a SATA Super Combo. But the power cable from the SATA Super combo is very unique, I can not able to give the power of this cable to my 2nd hard drive.

    Is it possible to add 2 hard disk in the PC case?

    Best regards

    Dani

    Hi Dani,

    The SFF is using a drive slim lens that does not have a standard SATA power connection. You will need to buy an adapter or a SATA power cable splitter to power a second hard drive.

  • Add disk 3,5 '' SATA for Optiplex 780

    I have a new (refurbished) desktop Optiplex 780 DT.  It has eight USB 2.0 connectors and not 3.x of USB connectors. I also have a 1 TB 3.5 '' SATA of an old machine (RIP) (WD1001FALS).

    1. do I have to add a card USB 3.0 update, I can use the external USB-SATA interface I 3.x USB speed.  I know the jury in the case, but what power and functional interface connections are available inside the case, or at least on the motherboard?

    2. what happens if I wanted to do an internal SATA drive, is there a (power and interface) connectors inside for that?  There is a white board which implies that I could fit the drive there, possibly with after-sales support.  Otherwise, I have it positioned as a mini tour, so I pose just the drive inside where it fits.

    3. If I had to choose to use the esata to the rear connector, is there a way to get power to the drive off the beaten track?

    Thank you

    Jan

    Hi Jan,

    Here's the manual for your Opti 780:

    There are two openings for a disk 3,5 '' HARD so lots of room inside. You will probably need a data cable, but there should be a spare power connector. There is 1 SATA and SATA 2 ports. Check the manual to see which is which.

    ESATA or USB, you will need an external enclosure. But any USB 3.0 expansion card update should be compatible with your system.

  • Windows XP 64 bit will run on a Dell Optiplex 780 SFF or Optiplex 980 SFF?

    I intend to buy a Dell Optiplex 780 SFF or a Dell Optiplex 980 SFF, but I would like to know which one will work with Windows XP 64-bit.

    For Windows XP 64 Bit its better to use the somewhat hidden (old ftp site):

    http://FTP.Dell.com/Browse_For_Drivers/desktops/OptiPlex/OptiPlex%20780/

    http://FTP.Dell.com/Browse_For_Drivers/desktops/OptiPlex/OptiPlex%20790/

    http://FTP.Dell.com/Browse_For_Drivers/desktops/OptiPlex/OptiPlex%20980/

    This has the old drivers listed in multiple versions, including XP x 64 drivers not mentioned on drivers and downloads. The new ftp site is currently slightly broken.

  • OptiPlex 780 Black Screen

    I have a slimline Optiplex 780. The video cable is an exclusive Dell DVI splitter. I tried both ports 1 and 2. When the system boots, the screen remains black, until Windows starts. After Windows starts the video system works very well. The problem is, I can't get in the config or the start menu because I don't see anything during POST.

    New video card fixed. Strange to have problem, but at least it works now.

Maybe you are looking for