questions from site to site vpn configuration

I am trying to connect to our offices with our remote data center, and I don't know exactly where to look for information.

Our Setup looks like:

[Office LAN: 192.168.0.0/22 (GE0/1)]-> [Cisco 2821 (GE0/0)]-> Internet <- [cisco="" 2911="" (ge0/0)]-="">[LAN DC: 10.10.10.0/26 (GE0/1)]

Can someone point me in the right direction to set up a VPN connection that routes traffic Office dedicated to the 10.10.10.0/26 network reach the data center?

Thank you!

Ben

You must have a single ACL NAT, so you need a config like this:

Site 1:

192.168.0.0/22 LAN

Site 2:

LAN 10.10.10.0/26

Site 1:

NAT extended IP access list

deny ip 192.168.0.0 0.0.3.255 10.10.10.0 0.0.0.63

IP 192.168.0.0 allow 0.0.3.255 all

overload of IP nat inside source list NAT concert 0/0 interface

concert int 0/1

IP nat inside

concert int 0/0

NAT outside IP

150 extended IP access list

IP 192.168.0.0 allow 0.0.3.255 10.10.10.0 0.0.0.63

Site 2:

NAT extended IP access list

refuse the 10.10.10.0 ip 0.0.0.63 192.168.0.0 0.0.3.255

IP 10.10.10.0 allow 0.0.0.63 everything

overload of IP nat inside source list NAT concert 0/0 interface

concert int 0/1

IP nat inside

concert int 0/0

NAT outside IP

150 extended IP access list

IP 192.168.0.0 allow 0.0.3.255 10.10.10.0 0.0.0.63

In addition, when you type the pre-shared key you must check if they match:

crypto ISAKMP key 6 asdf address datacenter.external.ip.address

ISAKMP crypto asdf keys address office.external.ip.address

6 in the early line shows that will follow a key encrypted according to me.

Make these changes and we will check the debug output:

debugging cry isa

debugging ipsec cry

term Lun

Federico.

Tags: Cisco Security

Similar Questions

  • Site to Site VPN configuration does not

    Hello

    I just tried to set up a test site to site VPN. Diagram of arrangement is attached. Router R2 is supposed to act as the 'Internet' to allow connectivity between the two networks.

    My VPN on ASA1 and ASA2 configs are below:

    ASA1

    Note to outside_cryptomap_1 to access list VPN traffic to encrypt
    outside_cryptomap_1 to access extended list ip 10.10.10.0 allow 255.255.255.0 172.16.10.0 255.225.255.0

    Crypto ikev1 allow outside
    IKEv1 crypto policy 1
    preshared authentication
    aes-256 encryption
    sha hash
    Group 5
    life 86400

    tunnel-group 11.11.11.2 type ipsec-l2l
    IPSec-attributes tunnel-Group 11.11.11.2
    Cisco pre-shared key IKEv1

    Crypto ipsec transform-set ikev1 AES - SHA esp-aes-256 esp-sha-hmac
    card crypto outside_map 1 match address outside_cryptomap_1
    peer set card crypto outside_map 1 11.11.11.2
    card crypto outside_map 1 set of transformation-AES-SHA
    outside_map interface card crypto outside

    ASA2

    Note to outside_cryptomap_1 to access list VPN traffic to encrypt
    permit access list extended ip 172.16.10.0 outside_cryptomap_1 255.255.255.0 10.10.10.0 255.225.255.0

    Crypto ikev1 allow outside
    IKEv1 crypto policy 1
    preshared authentication
    aes-256 encryption
    sha hash
    Group 5
    life 86400

    tunnel-group 12.12.12.2 type ipsec-l2l
    IPSec-attributes tunnel-group 12.12.12.2
    Cisco pre-shared key IKEv1

    Crypto ipsec transform-set ikev1 AES - SHA esp-aes-256 esp-sha-hmac
    card crypto outside_map 1 match address outside_cryptomap_1
    peer set card crypto outside_map 1 12.12.12.2
    card crypto outside_map 1 set of transformation-AES-SHA
    outside_map interface card crypto outside

    I can ping with the ASA2 ASA1, but when I try to test the VPN trying from one PC to another, I get nothing.

    I tried a few commands show and they came out absolutely empty... as I have not configured:

    SH in detail its crypto isakmp

    There are no SAs IKEv1

    There are no SAs IKEv2

    SH crypto ipsec his

    There is no ipsec security associations

    Anyone have any ideas?

    Hi martin,

    Your configs are quite right. I tried your script, its works really well. Here's the configs & outputs.
    What I mentioned in the previous note follow this.

    --------------------

    ASA1

    ASA1 (config) # sh run
    : Saved
    :
    ASA Version 8.0 (2)
    !
    hostname ASA1
    activate 8Ry2YjIyt7RRXU24 encrypted password
    names of
    !
    interface Ethernet0/0
    nameif outside
    security-level 0
    IP 12.12.12.2 255.255.255.0
    !
    interface Ethernet0/1
    nameif inside
    security-level 100
    10.10.10.2 IP address 255.255.255.0
    !
    interface Ethernet0/2
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Ethernet0/3
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Ethernet0/4
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Ethernet0/4
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Ethernet0/5
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    2KFQnbNIdI.2KYOU encrypted passwd
    passive FTP mode
    extended vpn 10.10.10.0 ip access list allow 255.255.255.0 172.16.10.0 255.255.255.0
    pager lines 24
    Within 1500 MTU
    Outside 1500 MTU
    no failover
    ICMP unreachable rate-limit 1 burst-size 1
    don't allow no asdm history
    ARP timeout 14400
    Route outside 0.0.0.0 0.0.0.0 12.12.12.1 1
    Timeout xlate 03:00
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout, uauth 0:05:00 absolute
    dynamic-access-policy-registration DfltAccessPolicy
    No snmp server location
    No snmp Server contact
    Server enable SNMP traps snmp authentication linkup, linkdown cold start
    Crypto ipsec transform-set esp-3des esp-sha-hmac tset
    card crypto cmap 1 match for vpn
    card crypto cmap 1 set peer 11.11.11.2
    card crypto cmap 1 transform-set tset
    cmap outside crypto map interface
    crypto ISAKMP allow outside
    crypto ISAKMP policy 1
    preshared authentication
    3des encryption
    md5 hash
    Group 5
    life 86400
    crypto ISAKMP policy 65535
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    Telnet timeout 5
    SSH timeout 5
    Console timeout 0
    a basic threat threat detection
    Statistics-list of access threat detection
    !
    !
    tunnel-group 11.11.11.2 type ipsec-l2l
    IPSec-attributes tunnel-Group 11.11.11.2
    pre-shared-key *.
    context of prompt hostname
    Cryptochecksum:00000000000000000000000000000000
    : end
    ASA1 (config) #.
    ---------------------

    ASA2 (config) # sh run
    : Saved
    :
    ASA Version 8.0 (2)
    !
    hostname ASA2
    activate 8Ry2YjIyt7RRXU24 encrypted password
    names of
    !
    interface Ethernet0/0
    nameif outside
    security-level 0
    IP 11.11.11.2 255.255.255.0
    !
    interface Ethernet0/1
    nameif inside
    security-level 100
    IP 172.16.10.2 255.255.255.0
    !
    interface Ethernet0/2
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Ethernet0/3
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Ethernet0/4
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Ethernet0/5
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    2KFQnbNIdI.2KYOU encrypted passwd
    passive FTP mode
    extended vpn 172.16.10.0 ip access list allow 255.255.255.0 10.10.10.0 255.255.255.0
    pager lines 24
    Outside 1500 MTU
    Within 1500 MTU
    no failover
    ICMP unreachable rate-limit 1 burst-size 1
    don't allow no asdm history
    ARP timeout 14400
    Route outside 0.0.0.0 0.0.0.0 11.11.11.1 1
    Timeout xlate 03:00
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout, uauth 0:05:00 absolute
    dynamic-access-policy-registration DfltAccessPolicy
    No snmp server location
    No snmp Server contact
    Server enable SNMP traps snmp authentication linkup, linkdown cold start
    Crypto ipsec transform-set esp-3des esp-sha-hmac tset
    card crypto cmap 1 match for vpn
    card crypto cmap 1 set peer 12.12.12.2
    card crypto cmap 1 transform-set tset
    cmap outside crypto map interface
    crypto ISAKMP allow outside
    crypto ISAKMP policy 1
    preshared authentication
    3des encryption
    md5 hash
    Group 5
    life 86400
    crypto ISAKMP policy 65535
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    Telnet timeout 5
    SSH timeout 5
    Console timeout 0
    a basic threat threat detection
    Statistics-list of access threat detection
    !
    !
    !
    tunnel-group 12.12.12.2 type ipsec-l2l
    IPSec-attributes tunnel-group 12.12.12.2
    pre-shared-key *.
    context of prompt hostname
    Cryptochecksum:00000000000000000000000000000000
    : end
    ASA2 (config) #.

    -------------------------
    OUTPUTS:

    *********************

    ASA1 (config) # sh crypto isakmp his

    ITS enabled: 1
    Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
    Total SA IKE: 1

    1 peer IKE: 11.11.11.2
    Type: L2L role: initiator
    Generate a new key: no State: MM_ACTIVE

    ---------------------

    ASA1 (config) # sh crypto ipsec his
    Interface: outside
    Tag crypto map: cmap, seq num: 1, local addr: 12.12.12.2

    access vpn ip 10.10.10.0 list allow 255.255.255.0 172.16.10.0 255.255.255.0
    local ident (addr, mask, prot, port): (10.10.10.0/255.255.255.0/0/0)
    Remote ident (addr, mask, prot, port): (172.16.10.0/255.255.255.0/0/0)
    current_peer: 11.11.11.2

    #pkts program: 50, #pkts encrypt: 50, #pkts digest: 50
    #pkts decaps: 49, #pkts decrypt: 49, #pkts check: 49
    compressed #pkts: 0, unzipped #pkts: 0
    #pkts uncompressed: 50, comp #pkts failed: 0, #pkts Dang failed: 0
    success #frag before: 0, failures before #frag: 0, #fragments created: 0
    Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
    #send errors: 0, #recv errors: 0

    local crypto endpt. : 12.12.12.2, remote Start crypto. : 11.11.11.2

    ------------------------
    ASA2 (config) # sh crypto isakmp his

    ITS enabled: 1
    Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
    Total SA IKE: 1

    1 peer IKE: 12.12.12.2
    Type: L2L role: answering machine
    Generate a new key: no State: MM_ACTIVE

    ------------------------

    ASA2 (config) # sh crypto ipsec his
    Interface: outside
    Tag crypto map: cmap, seq num: 1, local addr: 11.11.11.2

    access vpn ip 172.16.10.0 list allow 255.255.255.0 10.10.10.0 255.255.255.0
    local ident (addr, mask, prot, port): (172.16.10.0/255.255.255.0/0/0)
    Remote ident (addr, mask, prot, port): (10.10.10.0/255.255.255.0/0/0)
    current_peer: 12.12.12.2

    #pkts program: 49, #pkts encrypt: 49, #pkts digest: 49
    #pkts decaps: 50, #pkts decrypt: 50, #pkts check: 50
    compressed #pkts: 0, unzipped #pkts: 0
    #pkts uncompressed: 49, #pkts comp failed: 0, #pkts Dang failed: 0
    success #frag before: 0, failures before #frag: 0, #fragments created: 0
    Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
    #send errors: 0, #recv errors: 0

    local crypto endpt. : 11.11.11.2, remote Start crypto. : 12.12.12.2
    -------------------------

  • site to site vpn configuration

    I have windows server with two sites in different locations and that you want to configure a site to site vpn, how to configure

    Here is the Vista Forums.

    http://TechNet.Microsoft.com/en-us/WindowsServer/default.aspx

    Try server communities.

    See you soon.

    Mick Murphy - Microsoft partner

  • Site to site VPN configuration... Please it is urgent

    I WANT to CREATE THE SITE to SITE VPN... Then my friend send me to configure this setting, and I did not now how to set it up for CLI... Please someone can help me how to set up

    Thank you allllllll

    MODEM ROUTER VPN PEER IS 155.155.155.X

    IKE parameters

    Encryption Key Exchange = 3DES

    The integrity of the data / MD5 hash algorithm of ==

    Diffie-Hellman Group 1 phase is group 2

    IPSec life (seconds) is 86400

    IKE SA Lifetime (seconds = 86400

    -----------------------------------------------------------------------------------------------------------------------

    IPSEC settings

    UDP encapsulation = YES

    PROTOCOL IS ESP

    IPSEC = 3DES

    DATA INTEGRITITY = MD5

    PROTECT THE NETWORK = 192.168.80.0







    Here are two examples-

    http://packetlife.net/blog/2011/Jul/11/LAN-LAN-VPN-ASA-5505/

    http://www.networking-forum.com/wiki/ASA_VPNs

    Thank you

    Ajay

  • Multiple site-to-site vpn configuration

    I am able to successfully create two different ipsec tunnels and I need them to be operational at the same time. However, when I "crypto map" (physical) external interface of my PIX 515, one of them is operational both. The tunnels go to two different places, different peers and different pre-shared keys. I have to install a logical interface and one card for each or what? Any help is appreciated. I apologize if I didn't spend enough time looking for the forum for an answer, but I tried :-). If you could point me to an example configuration for this, would be great. Thanks in advance for your help.

    Mike

    use different sequence numbers for different VPN.

    card crypto outside_map 10 correspondence address outside_10_cryptomap

    card crypto outside_map 10 peer set 192.168.10.10

    outside_map crypto 10 card value transform-set ESP-3DES-SHA

    card crypto outside_map 20 match address outside_20_cryptomap

    peer set card crypto outside_map 20 192.168.20.20

    outside_map crypto 20 card value transform-set ESP-3DES-SHA

    outside_map interface card crypto outside

  • Help with a variety of questions from site Web/mobile app. (Advice and assistance)

    Hello, my cousin today asked me for help with his business. He wants a website and a mobile application for his company. Now here's the thing. I know how to create a very simple Web site. This isn't a problem. but he wants people to be able to assess the services he wants to be able to report on the Web site so they can comment, send messages, the whole nine yards. He also wants people to be able to pay via the website using norton scan security. Now, I have no idea how to do that. And did I mention that he wants an app? So I do not expect an answer, step by step the "end to end" on the creation of a Web site. To start with. Is this kind of thing, possible using programs compared to the creative clouds? Is it possible to create an app? What happened to create a way for people to pay via the website? I just want to help in being directed to the right direction in this learning experience. Then, where I start, this kind of thing is still possible? where should I go? where can I learn? ect. Any help and advice is highly appreciated and welcomed. So please if you have something to say. I'm listening.

    Thank you, the community.

    The first thing I would ask that your cousin is timeline... He asks a little... it is a great project that could have involved more than one person, especially if he wants a custom application.

    Cost would also be an important factor in accepting this type of work, how do you charge him if you don't know even how to do most of these things... As you say, you don't have any idea how to make the most of this work, and I think there's a big learning curve with some of the things he asks.

    But if he has the time and money and you have the time and practice to learn, there are cloud programs to create out there who can do whatever he wants.

  • You try to run a Site to site VPN and remote VPN from the same IP remotely

    We currently have a site to site VPN configuration between our offices call center and a 3rd party that allows them to access our training to their employees to use environment while being trained on our systems. This tunnel is running between our ASA and their ASA without problem; However, when we have managers come out to the call center, they are unable to use remote VPN to access our office.

    Apparently the same IP peer remote that we use for our site to the other tunnel is the same IP that our managers use to access the internet when they are on-site with the customer. When I look at the logs it shows the VPN attempt and then I get treatment Information Exchange has failed. So from what I can understand when our managers are trying to connect to our firewall from the same IP address as the counterpart of site to site it automatically tries to create a tunnel, according to the information of the site to the other tunnel. If our managers are anywhere else, they can connect through remote VPN with no problems.

    My question is if anyone knows of a way to make the firewall allow VPN site to site and remote connections with the same remote IP address.

    Hi John,.

    Basically, in older versions, when you hit a static encryption card and you does not match this static encryption completely map the connection continues until the dynamic encryption card. For this reason, you can connect your IPSec clients before. A bug has been opened on this vulnerability.

    CSCuc75090  Details of bug

    The crypto IPSec Security Association are created by dynamic crypto map to static peers

    Symptom:

    When a static VPN peer adds all traffic to the ACL crypto, a surveillance society is based even if the pair IP is not allowed in the acl to the main façade encryption. Are these SA finally put in correspondence and commissioning the dynamic crypto map instance.

    Conditions:

    It was a planned design since the first day that allowed customers to fall through in the case of static crypto map did not provide a necessary cryptographic services.

    The SA must be made from a peer configured statically and a dynamic crypto map instance must be configured on the receiving end.

    Workaround solution:

    N/A

    Some possible workarounds are:

    Configure a static nat device when you try to use the remote VPN if the firewall remotely will be hit with a different public IP address. It would be a good solution, but it will depend on how many ip addresses public you have available, if you really want one of these ip addresses for that access.

    Also, I thought you could use AnyConnect instead of the IPSec VPN client. I don't know how many users need to connect from your PC to the remote site, but the ASA has 2 licenses SSL available that you could use. Because Anyconnect uses the SSL protocol, it won't have a problem on your environment.

    Below some information:

    http://www.Cisco.com/c/en/us/TD/docs/security/ASA/asa84/configuration/guide/asa_84_cli_config/vpn_anyconnect.html

    Hope this helps,

    Luis.

  • Inside Source NAT from the remote host and VPN from Site to Site

    Hi all

    I was in charge of the construction of a vpn tunnel with a firewall PIX of our business partner company and ASA of the other company of the firewall.  Traffic will be A partner business users will access my company Citrix server.  I want to source-pat the user traffic partner company to PIX of my business within the interface to its entry in my LAN to access my company Citrix server.  The partner company will be PAT'ing their traffic from users to a single ip address - Let's say for discussion end is 65.99.100.101.  There is the site to site vpn configuration, and configure nat be performed to allow this traffic in accordance with the above provisions.

    I'm more concerned about the accuracy of the configuration of the domain encryption because NAT is involved in this whole upward.  My goal is to NAT (of the other company company a) ip address to a routable ip address in my company network.

    The fundamental question here is should I include the ip address of real source (65.99.100.101) of the company the user or IP natted (10.200.11.9) in the field of encryption.

    In other words should the encryption field looks like this

    OPTION A.

    permit ip host 10.200.11.103 65.99.100.101

    OR

    OPTION B

    permit ip host 10.200.11.103 10.200.11.9

    I'm inclined to think it should look like OPTION A.  Here's the part of MY complete SOCIETY of the VPN configuration.  I've also attached a diagram illustrating this topology.

    Thanks in advance,

    Adil

    CONFIG BELOW

    ------------------------------------------------

    #################################################

    Object-group Config:

    #################################################

    the COMPANY_A_NETWORK object-group network

    Description company network access my company A firm Citrix

    host of the object-Network 65.99.100.101

    the MYCOMPANY_CITRIX_FARM object-group network

    Description farm Citrix accessible Takata by Genpact

    host of the object-Network 10.200.11.103

    ################################################

    Config of encryption:

    ################################################

    crypto ISAKMP policy 20

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    ********************************

    CRYPTO MAP

    ********************************

    crypto Outside_map 561 card matches the address Outside_561_cryptomap

    card crypto Outside_map 561 set peer 55.5.245.21

    Outside_map 561 transform-set ESP-3DES-SHA crypto card game

    ********************************

    TUNNEL GROUP

    ********************************

    tunnel-group 55.5.245.21 type ipsec-l2l

    IPSec-attributes tunnel-group 55.5.245.21

    pre-shared-key * 55.5.245.21

    *******************************

    FIELD OF CRYPTO

    *******************************

    Outside_561_cryptomap list extended access permitted ip object-group MYCOMPANY_CITRIX_FARM-group of objects COMPANY_A_NETWORK

    ###########################################

    NAT'ing

    ###########################################

    Global (inside) 9 10.200.11.9

    NAT (9 genpact_source_nat list of outdoor outdoor access)

    genpact_source_nat list extended access permit ip host 65.99.100.101 all

    genpact_source_nat list extended access permit ip host 65.99.100.102 all

    ! For not natting ip address of the Citrix server

    Inside_nat0 list extended access permitted ip object-group MYCOMPANY_CITRIX_FARM-group of objects COMPANY_A_NETWORK

    You must include pre - nat ip 65.99.x.x in your crypto-card, like you did.

    For me, config you provided here looks good and meets your needs.

    One thing, I do not see here the nat rule real 0, but there is the ACL that NAT. probably, you just forgot this rule.

    65.99.100.101 #sthash.mQm0FIOM.dpuf

  • Problems with site-to-site vpn

    Hello world

    I recently received the mission assigned to the site to site vpn configuration and this is my first time. I'm trying to set up a vpn with pix 501 but short questions site. I managed to get that below, but I'm stuck now and do not know what could be the problem. Here's the debug output.

    Any help is greatly appreciated on what could be the potential problem.

    -AK

    ISAKMP (0:0): sending of NAT - T vendor ID - rev 2 & 3
    ISAKMP (0): early changes of Main Mode
    crypto_isakmp_process_block:src:208.249.117.203, dest:70.91.20.245 spt:500 dpt:500
    Exchange OAK_MM
    ISAKMP (0): treatment ITS payload. Message ID = 0

    ISAKMP (0): audit ISAKMP transform 1 against 20 priority policy
    ISAKMP: 3DES-CBC encryption
    ISAKMP: hash SHA
    ISAKMP: default group 2
    ISAKMP: preshared auth
    ISAKMP: type of life in seconds
    ISAKMP: duration of life (basic) of 28800
    ISAKMP (0): atts are acceptable. Next payload is 0
    ISAKMP (0): load useful treatment vendor id

    ISAKMP (0): ITS been pre-shared key, using id ID_IPV4_ADDR type authentication

    to return to the State is IKMP_NO_ERROR
    crypto_isakmp_process_block:src:208.249.117.203, dest:70.91.20.245 spt:500 dpt:5
    00
    Exchange OAK_MM
    ISAKMP (0): processing KE payload. Message ID = 0

    ISAKMP (0): processing NONCE payload. Message ID = 0

    ISAKMP (0): load useful treatment vendor id

    ISAKMP (0): load useful treatment vendor id

    ISAKMP (0): provider v6 code received xauth

    ISAKMP (0): load useful treatment vendor id

    ISAKMP (0): addressing another box of IOS!

    ISAKMP (0): load useful treatment vendor id

    ISAKMP (0): addressing a VPN3000 concentrator

    ISAKMP (0): ID payload
    next payload: 8
    type: 1
    Protocol: 17
    Port: 0
    Length: 8
    ISAKMP (0): the total payload length: 12
    to return to the State is IKMP_NO_ERROR
    crypto_isakmp_process_block:src:208.249.117.203, dest:70.91.20.245 spt:500 dpt:5
    00
    Exchange OAK_MM
    ISAKMP (0): processing ID payload. Message ID = 0
    ISAKMP (0): HASH payload processing. Message ID = 0
    ISAKMP (0): keep treatment alive: proposal = 32767/32767 sec., real = 3276/2 sec.

    ISAKMP (0): load useful treatment vendor id

    ISAKMP (0): Peer Remote supports dead peer detection

    ISAKMP (0): SA has been authenticated.

    ISAKMP (0): start Quick Mode changes, 413131006:189fe0feIPSEC (key_e M - ID
    (Display): had an event of the queue...
    IPSec (spi_response): spi 0x3e9451fa graduation (1049907706) for SA
    from 208.249.117.203 to 70.91.20.245 for prot 3

    to return to the State is IKMP_NO_ERROR
    ISAKMP (0): send to notify INITIAL_CONTACT
    ISAKMP (0): sending message 24578 NOTIFY 1 protocol
    Peer VPN: ISAKMP: approved new addition: ip:208.249.117.203/500 Total VPN peer: 1
    Peer VPN: ISAKMP: ip:208.249.117.203/500 Ref cnt is incremented to peers: 1 Total VPN
    Peers: 1
    crypto_isakmp_process_block:src:208.249.117.203, dest:70.91.20.245 spt:500 dpt:5
    00
    ISAKMP (0): processing DELETE payload. Message ID = 3425658127, spi size = 16
    ISAKMP (0): delete SA: src 70.91.20.245 dst 208.249.117.203
    to return to the State is IKMP_NO_ERR_NO_TRANS
    ISADB: Reaper checking HIS 0xac149c, id_conn = 0 DELETE IT!

    Peer VPN: ISAKMP: ip:208.249.117.203/500 Ref cnt decremented to peers: 0 Total VPN
    Peers: 1
    Peer VPN: ISAKMP: deleted peer: ip:208.249.117.203/500 VPN peer Total: 0IPSEC (ke
    y_engine): got an event from the queue.
    IPSec (key_engine_delete_sas): rec would remove the ISAKMP notify
    IPSec (key_engine_delete_sas): remove all SAs shared with 208.249.117.203
    IPSec (key_engine): request timer shot: count = 2,.
    local (identity) = 70.91.20.245, distance = 208.249.117.203.
    local_proxy = 0.0.0.0/0.0.0.0/0/0 (type = 4),
    remote_proxy = 206.200.22.0/255.255.255.0/0/0 (type = 4)

    Hello

    Newspapers, I see you are using a VPN 3000 Concentrator as the remote vpn end point. Now, also of the debugs next section is interesting:

    local (identity) = 70.91.20.245, distance = 208.249.117.203.
    local_proxy = 0.0.0.0/0.0.0.0/0/0 (type = 4),
    remote_proxy = 206.200.22.0/255.255.255.0/0/0 (type = 4)

    -Looks like our traffic interesting PIX and the hub are not mirrors of each other, and does not. Can you please paste the PIX here cryptographic access lists, so that I can analyze the entries.

    -Also, please make sure that you have followed all the steps during the vpn configuration according to the following links:

    If your PIX is running at version 7.x and more: http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a008064a06f.shtml

    If your PIX is running version 6.3.x: http://www.cisco.com/en/US/products/hw/vpndevc/ps2284/products_configuration_example09186a00800949d2.shtml

    Once you check the config on PIX and concentrator, please provide me with the output of "sh cry isa his" and "sh cry ipsec his ' of the PIX. With this release, we can continue to troubleshoot if there is more questions.

    Let me know if this can help,

    See you soon,.

    Christian V

  • Site to Site VPN number

    Hello

    I am facing a problem in my site to site VPN configuration, router management site gets the address public IP of the DHCP server as I have built a dynamic crypto map on the router HQ

    First phase ISAKMP is operational running, I am trying to ping the LAN 192.168.85.0 for the HQ 172.16.12.0 LAN but it won't go through and when I check the ipsec security associations I can see that packets are encrypted on the side of the branch and decrypted on the side of HQ but the HQ router no PING response at all and he saw not encrypted packets

    I have attached my configurations, I had to hide some information just for safety

    Help, please!

    Mostafa

    Hello Mustafa,

    Havinf a glance at your config, it seems you have not correctly configured on your HQ NAT exemption.

     ip access-list extended NAT deny ip 172.16.12.0 0.0.0.255 192.168.75.0 0.0.0.255 deny ip 172.16.12.0 0.0.0.255 172.16.20.0 0.0.0.255 permit ip 172.16.12.0 0.0.0.255 any deny ip 172.16.12.0 0.0.0.255 192.168.85.0 0.0.0.255

    In this interesting ACL traffic is refused in the last. So it is not exempted from NAT, as ACL are processed in top-down, your valuable traffic is already matching permit statement in NAT ACL therefore subject to NAT on HQ. Refuse the declaration of exemption, interesting traffic NAT should precede the statement of license.

    HTH

    "Please note useful posts.

  • devices to set up a site to site vpn

    I have a stupid question.  In a site to site vpn environment, can I do the installation program by using an asa5505 on one end and a router 1811 on the other end or do I need to have two asa5505 or two 1811 routers? Can another word, I mix and match devices and perform still a site to site vpn configuration or do I have to have the same features on the two end?

    You can mix and match all you want. To him my friend. Reference the link below.

    https://supportforums.Cisco.com/videos/2763

  • Site to Site VPN ASA 5510

    OK my forehead is painful to all keyboard strokes that I know that it must be something simple, but I am brand new to the SAA.  I had a site to site VPN configuration via routers 1751 that worked very well, but we're looking to add some more remote field offices, and I felt that it would be easier to maintain several sites is on the ASA 5510.  I have the VPN configured on the SAA and he said that the tunnel is up.  I can telnet to the ASA and ping the remote gateway on the even side of VPN and it pings fine.  If I try to ping on a local computer, I get a "Request timed out".  If I makes no changes apart from go to the computer room and replace the network cable the 1751 and then through the 1751 I can now ping the remote door way to my computer.  The remote router works obviously very well, my statement of route on my router for vpn push through the ASA (same ip address) IP traffic that has been used by the 1751 works obviously. It seems so just like ASA is not being pushed in the ethernet0/0 VPN traffic or at least it is not encrypted.  I also noticed that the ACL for NAT seems to increase in number of access either it seems, there is really just one small thing missing to make the ASA except and encrypt incoming traffic on ethernet0/0:

    My network is not configured with a DMZ is something like that, the ASA ethernet0/0 and my local network on the same subnet:

    Router (Cisco 2811)

    |

    Layer switch 2 (ProCurve)

    |                                      |

    ASA5510 LAN computers

    I'm trying to except both sides of the VPN in and out on Ethernet0/0 traffic I saw there was a framework for this "permit communication between VPN peers connected to the same interface' and I've activated this option.

    In short, I need to understand why the VPN tunnel shows that upward and I can ping the remote of the SAA, but peripheral gateway on my network can not ping to the remote gateway through the int Ethernet0/0 on the SAA.

    From the console of the ASA, I get this:

    ASA5510 # ping 192.52.128.1
    Send 5, echoes ICMP 100 bytes to 192.52.128.1, wait time is 2 seconds:
    !!!!!
    Success rate is 100 per cent (5/5), round-trip min/avg/max = 100/108/120 ms

    ASA5510 # show crypto ipsec his
    Interface: *.
    Tag crypto map: * _map, local addr: 10.52.120.23

    local ident (addr, mask, prot, port): (10.52.120.0/255.255.255.0/0/0)
    Remote ident (addr, mask, prot, port): (192.52.128.0/255.255.255.0/0/0)
    current_peer: x.x.x.204

    program #pkts: 9, #pkts encrypt: 9, #pkts digest: 9
    decaps #pkts: 9, #pkts decrypt: 9, #pkts check: 9
    compressed #pkts: 0, unzipped #pkts: 0
    #pkts uncompressed: 9, #pkts comp failed: 0, #pkts Dang failed: 0
    #send errors: 0, #recv errors: 0

    local crypto endpt. : 10.52.120.23, remote Start crypto. : x.x.x.204

    Path mtu 1500, fresh ipsec generals 60, media, mtu 1500
    current outbound SPI: C49EF75F

    SAS of the esp on arrival:
    SPI: 0x21FDBB9D (570276765)
    transform: esp-3des esp-md5-hmac
    running parameters = {L2L, Tunnel}
    slot: 0, id_conn: 1, crypto-map: * _map
    calendar of his: service life remaining (KB/s) key: (3824999/3529)
    Size IV: 8 bytes
    support for replay detection: Y
    outgoing esp sas:
    SPI: 0xC49EF75F (3298752351)
    transform: esp-3des esp-md5-hmac
    running parameters = {L2L, Tunnel}
    slot: 0, id_conn: 1, crypto-map: * _map
    calendar of his: service life remaining (KB/s) key: (3824999/3527)
    Size IV: 8 bytes
    support for replay detection: Y

    From my office on the 10.52.120.0 even the etherenet0/0 interface on the ASA network I get this:

    C:\Users\***>ping 192.52.128.1

    Ping 192.52.128.1 with 32 bytes of data:
    Request timed out.
    Request timed out.
    Request timed out.
    Request timed out.

    Ping statistics for 192.52.128.1:
    Packets: Sent = 4, received = 0, lost = 4 (100% loss)

    C:\Users\***>ping 10.52.120.23

    Ping 10.52.120.23 with 32 bytes of data:
    Reply from 10.52.120.23: bytes = 32 time = 5ms TTL = 255
    Reply from 10.52.120.23: bytes = 32 time = 3ms TTL = 255
    Reply from 10.52.120.23: bytes = 32 time = 1ms TTL = 255
    Reply from 10.52.120.23: bytes = 32 time = 1ms TTL = 255

    Ping statistics for 10.52.120.23:
    Packets: Sent = 4, received = 4, lost = 0 (0% loss),
    Time approximate round trip in milli-seconds:
    Minimum = 1ms, Maximum = 5ms, average = 2ms

    Count on VPN Tunnel ACL does not increase when I try to ping the address of the remote gateway.

    Here is the running of the ASA configuration:

    ASA Version 7.0 (2)
    names of
    !
    interface Ethernet0/0
    nameif InsideNetwork
    security-level 100
    IP 10.52.120.23 255.255.255.0
    !
    interface Ethernet0/1
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Ethernet0/2
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Management0/0
    Shutdown
    nameif management
    security-level 100
    IP 192.168.1.1 255.255.255.0
    management only
    !
    activate the encrypted password of XXXXXXXXXXXXXXXX
    passwd encrypted XXXXXXXXXXXXXXXXXXX
    ciscoasa hostname
    domain default.domain.invalid
    passive FTP mode
    permit same-security-traffic intra-interface
    Access extensive list ip 10.52.120.0 InsideNetwork_nat0_outbound allow 255.255.25
    5.0 192.52.128.0 255.255.255.0
    Access extensive list ip 10.52.120.0 InsideNetwork_cryptomap_20 allow 255.255.255
    .0 192.52.128.0 255.255.255.0
    pager lines 24
    asdm of logging of information
    management of MTU 1500
    MTU 1500 InsideNetwork
    management of the interface of the monitor
    the interface of the monitor InsideNetwork
    ASDM image disk0: / asdm - 502.bin
    don't allow no asdm history
    ARP timeout 14400
    NAT (InsideNetwork) 0-list of access InsideNetwork_nat0_outbound
    Route InsideNetwork 0.0.0.0 0.0.0.0 10.52.120.1 1
    Timeout xlate 03:00
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00
    Timeout mgcp-pat 0:05:00 sip 0:30:00 sip_media 0:02:00
    Timeout, uauth 0:05:00 absolute
    Enable http server
    http 192.168.1.0 255.255.255.0 management
    http 10.52.120.0 255.255.255.0 InsideNetwork
    No snmp server location
    No snmp Server contact
    Server enable SNMP traps snmp
    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
    card crypto InsideNetwork_map 20 corresponds to the address InsideNetwork_cryptomap_20
    card crypto InsideNetwork_map 20 set peer x.x.x.204
    InsideNetwork_map 20 transform-set ESP-3DES-MD5 crypto card game
    InsideNetwork_map InsideNetwork crypto map interface
    ISAKMP enable InsideNetwork
    part of pre authentication ISAKMP policy 10
    ISAKMP policy 10 3des encryption
    ISAKMP policy 10 md5 hash
    10 2 ISAKMP policy group
    ISAKMP life duration strategy 10 86400
    Telnet 10.52.120.0 255.255.255.0 InsideNetwork
    Telnet timeout 5
    SSH timeout 5
    Console timeout 0
    management of 192.168.1.2 - dhcpd address 192.168.1.254
    dhcpd lease 3600
    dhcpd ping_timeout 50
    enable dhcpd management
    tunnel-group x.x.x.204 type ipsec-l2l
    x.x.x.204 group of tunnel ipsec-attributes
    pre-shared-key *.
    !
    class-map inspection_default
    match default-inspection-traffic
    !
    !
    Policy-map global_policy
    class inspection_default
    inspect the dns-length maximum 512
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    inspect the rsh
    inspect the rtsp
    inspect esmtp
    inspect sqlnet
    inspect the skinny
    inspect sunrpc
    inspect xdmcp
    inspect the sip
    inspect the netbios
    inspect the tftp
    !
    global service-policy global_policy
    Cryptochecksum:7e478b60b3e406091de466675c52eaaa
    : end

    I haven't added anything to the config except what seemed necessary to get the job of VPN tunnel.  It should be fairly clean.

    Thanks in advance for any help... I really hope that it is something really simple as a recruit ASA just forgot

    Strange, but good news. Thanks for the update. I'm glad everything is working.

    THX

    MS

  • 887VDSL2 IPSec site to site vpn does NOT use the easy vpn

    Much of community support.

    as I'm looking through the config Guide about 870 router series, only to find information about the config with eazy vpn.

    is there a classic way, about 870 Series site 2 site without eazy vpn IPSec configuration?

    Have a classic way if a tunnel? Have the 870 is not as a vpn client?

    Thank you

    Of course, here's example of Site to Site VPN configuration for your reference:

    http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080194650.shtml

    http://www.Cisco.com/en/us/products/HW/routers/ps221/products_configuration_example09186a008073e078.shtml

    Hope that helps.

  • RV180 restrict access to the Site to Site VPN

    Hello

    I'm trying to set up my network so that VPN traffic is routed only to a physical single on the RV180 port or to a certain subset of devices on a network.

    I have a site to site vpn configuration in a Home Office and connect to the corporate network.  The user has a couple of devices on the home network who need to access the corporate network.

    We hope to leave his PC accessible to its home network and the corporate network, but limit other devices to access the vpn.

    I think that I could do playing with the subnet, but I just can't get my head around it.

    It must be something simpleish to do this, isn't there?

    I'd appreciate any help you have.

    Thank you

    Gary

    Hi boys, here's a hypothetical situation.

    VLAN 1 is port 1

    VLAN 2 is port 2

    VLAN 1 has a switch connected to your local network of services

    VLAN 2 has a switch to maintain your VPN.

    The configuration of the port for each port would be the vlan respective unidentified.

    You can disable the router in order to prohibit intervlan communication. But also, and especially, the vpn is a specific meaning, subnet, you specify the specific ip subnet on the config of the tunnel because the config include not a second subnet will not work it's traffic in the tunnel.

    -Tom
    Please mark replied messages useful

  • Site to site VPN to allow sharing of files and AD domain trust.

    Hello

    I don't know exactly what I need to add to a current site 2 site vpn activate specifically these processes (2).

    Happy Advisor.

    Without knowing the current site-to-site VPN configuration, it is difficult to give you a good answer on what you add. The site of the current to the other use a card encryption with an access list that identifies the traffic is encrypted? If yes then you should probably add something to the access list. The current site to use a tunnel and encrypt everything that goes through the tunnel. If Yes, then you should probably add the routing logic that ensures that this traffic is sent through the tunnel.

    HTH

    Rick

Maybe you are looking for