R50E does not start after upgrading memory

Similar Questions

• Satellite A200 PSAEOE does not start after upgrading memory

  Hi, I am first time here.

  I bought a Toshiba A200 PSAE0E-03J02JDR with 2 GB of RAM. I bought a pair of ram Corsair (2 * 2 GB VS2GSDS667D2). The computer does not start after that I installed the memory. I have intel 945 chipset, which is capable of 4 GB (manual page 1-2). The bios version is 1.8 2007.

  Can anyone help me, please.

  Post edited by: Marian ovidiu

  Hello

  The A200 series supports different chipsets;
  Intel 945 PM
  Intel 945GM
  Intel 943GML

  As far as I know your laptop supports the * 943GML * Intel chipset and the chipset supports 2 GB RAM max.
  Take a look at your laptop s user manual * Page 18.*

  Summer: 4 GB of RAM are not possible, and therefore your laptop does not start.

• Satellite L100 113 does not start after upgrading memory

  Hello.

  Our Integrator bring to our company KVR800D2S5, but laptop memory modules does not start :(

  I read manual - this laptop supports 533 PC4200 memory modules.

  But SO-DIMM 533 MHz will be delivered in one month...

  The memory modules, we can install to Toshiba L100-113?

  Thank you.

  Hello

  I think that the laptop does not power upward because of a barrette memory faulty or not fully compatible.

  Please visit this memory 3rd party:

  [Memory for Toshiba Satellite L100 113 | http://www.orcalogic.co.uk/asp/prodtype.asp?prodtype=22360&ft=m&st=3]

  As you can see Satellite L100 113 memory can be upgraded up to 2 GB (2 x 1 GB) and you must use the DDR2 533 MHz (PC2-4200) 200 - PIN SODIMM

  Concerning

• Satellite A60-672 does not start after upgrading memory

  Hello

  I bought an additional memory for my laptop, but after installing it the PC will start is no longer, when I turn it on it makes a brief noise then nothing. After taking the memory expansion out again once, the laptop still does not start.

  Peter

  Hello

  I agree with "guy sos." There is no doubt motherboard problem now. I assume you used the incompatible memory module.

  In any case, contact the after-sales Service of Toshiba partner in your country and explain to them the situation. The address that you will find under http://www.csd.toshiba.com/cgi-bin/tais/su/su_gaspLocator.jsp?pf=true

  Good bye

• Satellite 1410-304 does not start after upgrading memory

  I tried to extend the memory of 512 MB to 1 GB by placing two memory modules in my laptop Satellite 1410-304.
  These blocks of memory are each 512 MB and type: DDR400 PC3200 SODIMM.

  Each memory separate block in one of the memory slots A or B works well, no problems.

  However, when the two blocks of memory are installed, the laptop does not start no more.
  I hear the soft beeps indicating that a problem has occurred. The system works under Windows XP.

  Someone who can tell me how to solve this problem. Thanks in advance for your help

  concerning

  Marten

  Memory sticks are made by the same company? If this isn't the case, it will not work.

• NB305 - does not start after upgrading memory

  Have just bought 2GB memory update for Toshiba NB305-106, and it does not work. Machine unbootable - started 1 GB module.

  Just read a post on memory upgrade problems - different users having problems and they used Crucial memory without any problems. -Is it true?
  Anyone got an advisor?

  Hi ian123,

  If the boot netbook doesn't, additional memory module which means this module is not compatible and you need another.

  It would be interesting to know which module you are buying exactly and what specs it has.
  Can you post this information?

  In General, I have good experience with the modules of Kingston

• Satellite L50 - A - 1 5 PSKK6E does not start after upgrading memory

  Upgrade memory L50 - A - 1 5 pskk6e

  I have a memory ddr3 4 gb 1rx8 pc3 - 12800 S-11-12-b2 hynix and I tried to add another memory
  memory DDR3 4 gb 1rx8 hynix pc3 - 12800 S-11-11-b2, but it does not boot up the laptop.

  I tried to mount only the new but it won't start.

  Some ideas?

  I think that it s you already know that this Satellite L50 - has - 1 5 would support max 16 GB of RAM (2 x 8 GB)

  But why, box for computer laptop doesn t is very simple: the new modules are not compatible.

  I found modules recommended by Toshiba.
  These are:
  8GB DDR3L - 1600 PA5104U-1M8G
  4 GB DDR3L - 1600 PA5104U-1M4G

  Both are made of Kingston and the specifications are:

  Memory speed: 1600 Mhz PC3-12800
  Capacity: 8 GB (1x8GB module)
  Pins: 204 SODIMM
  Type of RAM: DDR3 SODIMM
  Verifying the integrity of data: non ECC
  Specifications:
  Latency (CL) CASES: 11
  Voltage: 1.35v

• Satellite M30X-122 does not start after upgrading memory

  Hello

  I want to upgrade the RAM in my Satellite M30X 122. Correctly my NB contains 2x256MB.
  I bought a GB 1 333 MHz. Cl2.5 module PC2700 (corresponds to the former, but more grand ;-)))
  Now I build in the module, but after the build-in system is dead.
  It doesn't show anything on the screen (after pressing the button one)).

  Does Anyboby have some tips?

  Thank you very much
  Peter

  Hello

  Toshiba has recommended the use of these memory modules:
  PC2700 256 MB (PA3311U - 1 M 25)
  PC2700 512 MB (PA3312U - 1 M 51)
  1024MO PC2700 (PA3313U-1M1G)

  Well, the size of 1024MB should be compatible. In this case, it s not a module size.
  Have you tried to get into the BIOS? BIOS recognizes the memory module?
  Maybe the module is broken?

  In my opinion, you should check if the module memory works on a different unit. If this module works correctly on another unit if your M30X doesn t support this module of memory and you need one another.

• Satellite M100 does not start after upgrading memory

  I recently bought two sticks of DDR2 1 GB 533 Mhz RAM memory.
  I placed both in the slots (the one under the keyboard and one at the rear).

  For some reason any when I try to turn the computer back on to, nothing happens.
  The screen is black and nothing seems to load.

  Help please!

  The case is clear like a Crystal;

  The M100 cannot start because memory modules are not fully consistent or both modules or only a single module is defective.

  I put t see any other solution to test for laptop with other modules

• Satellite C660D-107 does not start after upgrading memory

  Hi all

  I just bought a Kingmax 4 GB 1333 Mhz memory for my laptop C660D-107.

  Yesterday, I put and I saw on the BIOS if the laptop recognizes it or not.
  The laptop showed the 4 GB memory but when I booted the machine nothing happened.

  Black screen and nothing else.
  The specification to write 8 GB of RAM maximum (1066 Mhz).
  I think that 4-4 GB. The frequency is perhaps the problem?
  Opus 64-bit Win7 system

  concerning

  Robert

  Hello

  The bus front end (FSB) manages 1066 Mhz max.
  Thus, your memory at 1333 Mhz Kingmax cannot operate at 1333 Mhz.
  Usually, this should not be a problem and modules more quickly would run slowly at 1066 Mhz but there may be a compatibility issue.

  Edit the memory at 1066 Mhz I have so I recommend using modules from Kingston and hand never any problem.

• FF does not start after upgrading to version 27.0.1

  FF does not start after upgrading to version 27.0.1
  Crash ID: bp-2bc18734-d643-4843-a10f-fd6102140214

  Firefox 27.0.1 is too recent for me to know what unique issues it may have. I will message you a link to download the installer for Firefox 27.0 to see that the inversion or not the problem.

• Re: Smoker L30-10 X PSL33E does not start after upgrading RAM

  Hello

  I have a problem with my laptop.
  It has 1024 MB of RAM (2 x 512), but it wasn't enough, so I decided to update to 2048 MB (2 x 1024).

  I bought two modules and my computer does not start after changing them.
  It was only a screen black (same BIOS has not started). I tried another combination of installation of memory modules RAM.
  2 x 1024 - did not work
  1 x 1024 - did not work
  1 x 1024 + 1 x 512 - working but not properly.

  BIOS find that I only 896 MB (1024-128 for the video card)
  I said OK. Let's see what will show windows. He was also 896 MB.
  I launched CPU - Z and it shows that the total size of memory is 1536 MB (medium detect both modules).
  I found that CPU - Z detect 1 module 1 024 MB and 512 MB secondary, but the BIOS detect only 1024 MB 1536. How is that possible?

  I have fought, is that my BIOS is old, then I update the toshiba Web site form most recent version, but the problem persists.
  Please someboy help me and tell what to do.

  PS. the Modules are new and work correctly.
  They have been tested.

  Hello

  Have you used two identical RAM modules?

  What kind of modules did you use?

  In my view, that the problem is related to the new, inserted modules.
  There must be something wrong with the modules or modules are not completely compatible if the laptop can not boot after installation.

  According to a few pages of the book handles the DDR2 533 MHz (PC2-4200) 200-PIN SODIMM modules.

  Did you use these modules?

• Satellite P200D-130 does not start after upgrading RAM

  Hi, I just upgraded the RAM on my P200D 130 but it does not start after that.
  I removed the 2 Hynix 1 GB PC2-5200 and put in 2 SO Kingston DDR2 2 GB PC667 (should be the same as PC2-5200).
  Post-market nothing happens, light power control is turned on, I him stays CD drive but screen black, no beeps.

  I put one of the 1 GB modules, it starts normally, then I tried a 1 GB into the lower slot module and a 2 GB module in the top slot and it works.
  I tried a single 2 GB module in each slot, even in the form of 2 2 GB modules.

  What could be the reason, better: what would be the solution to ensure that the modules of 2 x 2 GB to work?

  Thanks in advance,

  Michael

  Hello!

  I think that both modules are not compatible to the laptop.
  Normally you can upgrade your laptop to 4 GB. Look in the user manual.

  The RAM, you should bring the computer dealer and request a new one. More buy modules with the same specifications and dimensions. Try buying RAM with the same specs as before.

  Good bye

• W500 PCI-Express does not work after upgrade memory 4gig

  Laptop is a W500 with WinXP SP3. I have the external ViDock PCI Express video card. Absolutely, it works like a champ. I recently received an upgrade of memory 4gig for the W500. After the upgrade of the default value would be 2gig RAM for the new 4gig, the laptop does NOT start with the inserted PCI Express card. I remove the card PCI Express ViDock and it starts very well and of course, works very well. Same behavior either stand alone or in the docking station. I tried going back to the 2 Gig of RAM and the new ViDock works perfectly. Google is pretty quiet on this issue... This could be a problem with the ViDock? the W500? Windows XP? The memory? Doesn't seem wise for me a memory 'simple' update would disable a component. Thank you,-Ryan

  May be the same as the question TOLUD?
  http://forums.Lenovo.com/T5/T400-T500-and-newer-T-series/request-to-fix-TOLUD-in-newer-BIOS-files/TD...

• listener does not start after upgrading clusterware

  Hello. RHEL 5, updated the clusterware 10.2.0.5 RAC to version 11.2.0.4 grid (database version is always 10). After the reboot, a node is OK, but on another auditor does not start. If trying to run manually, it starts with the error "the listener supports no services". After comparing with another node, it seems that 'bad' node uses old file listener.ora, which is now 0 bytes (probably was allowed during the upgrade):
  
  $lsnrctl start
  LSNRCTL for Linux: Version 10.2.0.5.0 - Production on 12 March 2014 09:37:16
  From /u01/app/oracle/product/10.2.0/db_1/bin/tnslsnr: Please wait...
  ...
  System settings file is /u01/app/oracle/product/10.2.0/db_1/network/admin/listener.ora
  Log messages written to /u01/app/oracle/product/10.2.0/db_1/network/log/listener.log
  Listen on: (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp) (HOST = rac - 2)(PORT=1521)))
  ...
  The listener supports no services ".

  where/u01/app... - is my home, the home grid is in / U02 oracle. On another node, listener starting grid House. I checked the Setup log and found no errors on the listener. What can I do to fix this?

  You need to check first, which is not running and why (. / crsctl res stat - you), a lot of resources are dependent on network net1. Start by watching clusterware alertlog and check the config network of the second node. If the basic config is very good, you can try with netca or command line (oifcfg, iflist,...).