Re: Equium A200-15i: Wireless stops working, so wireless adpater visible

Similar Questions

• Equium A200-15i: cannot see wireless network adapter

  Hi all.

  I tried to install the drivers on my laptop wireless without a bit of luck.
  My network card works, and I can connect to the internet via ethernet. But wireless doesn't work at all.

  I checked under network adapters and Device Manager, it shows realtek fast ethernet nic and 1394 network adapter.
  In the other devices section, it shows Ethernet controller... I tried to score for the drivers that I downloaded but it says "no new pilots could be detected.

  I hope someone can help
  (also - wlan is enabled in the laptop, but nothing happens - and it only shows my connection to the local network in network connections)

  I see that your wireless network card is not mentioned under network adapters in the Device Manager and so I m 1005 sure that Wlan card driver was not installed.

  I think that you were unable to install it because you used all just a bad driver!
  Equium A200-15I belongs to the * PSAE2E * series.

  Please check that you have chosen the right notebook series and downloaded the correct driver.
  As far as I know this unit should support the card of XB63L Wlan Atheros 11 b/g (13ch).

  Good luck buddy

• Equium A200-15I can't find wireless networks after recovery

  After making a recovery using the Vista CD from my computer (an Equium A200 15I) cannot find wireless networks. I went into the device under network adapters Manager and then there is realtek RTL8101 Ethernet NIC etc and in the other devices section it is Ethernet and controller of Stoeage of mass.

  I'm not really sure how I can get the computer to recognize and wireless networks, but I am aware that the driver is missing!

  Hello

  Try to update the wlan driver:

  http://APS2.toshiba-tro.de/WLAN/?page=downloads

  You can also check for other drivers if it is not installed:

  http://EU.computers.Toshiba-Europe.com/innovation/download_drivers_bios.jsp

• Equium A200-15i - loss of internet connection

  Hello!

  I have a really strange problem with my Equium A200-15i. My computer loses the connection with the internet very often.

  Connectivity shows that I am connected to the LAN or WLAN (if I use an ethernet cable). However, I am not connected to the internet. The network said "connected" icon, but everytime I open IE, the display shows 'page not available', my email client and communicators do not work as well.

  I checked all the wireless and ethernet settings and they are ok. Ive has run the diagnostics - ok. Device Manager indicates NICs (lan and wlan) are working properly. Router (BT HUB) is ok, there are more than two computers with it and they work perfectly (another computer laptop workes on wireless and PC is connected with the cable), so the problem is with my Toshiba only. Also, I say that we had a differenf router before and everything was good.

  When I restart my laptop it is internet connection but not for long. After a few reboots even who stops to help and I get the message "connected to the unidentified network, limmited to access" or sth like that. Then I restart the router security settings, fix it again and put the new settings into my laptop. This may help, but not for long... After a few days or a few hours sometimes everything again.

  Anyone, please help. I'm really, really confused :(:(

  Hello

  Please talk to WLAN and LAN connectivity separately? As a first step, it will be interesting to know what is with LAN connectivity. If you disable WLAN you are able to use permanent LAN connectivity?

  In most cases people have problems with WIFI but not so often with LAN connectivity because of that as a first step, that I just want to know if the local network works well. I have 3 laptops connected to my router and have never noticed any problem with the connection to the local network. I must say that I have the PPPOE settings. All of the TCP/IP parameters are set automatically to.

• Equium A200-15I - cannot connect to networks

  I have an Equium A200-15I and unable to connect to wireless networks. I can connect properly to my network wireless at home and in the past have had no problem connecting to networks wireless in other places.

  However, recently I have been unable to connect to random networks, some security enabled (for which I have the password) and one that was not secure, but that I have connected to in the past (to my parents house in the middle of the campaign, so no need to secure). He found fine networks and I can click on connect and put the password and then it flashes just between IP address acquisition and disconnected and not connects. I know that passwords are correct. I tried connected to the network woreless manually, and the same thing happens. It's really frustrating.

  I also have problems in playback of some DVD.

  I would appreciate help with this.

  Thank you

  Hello

  The WLAN driver is perhaps the reason for this and the work of doesn t correctly. You should check the Toshiba for WLAN driver update page:
  http://APS2.toshiba-tro.de/WLAN/

  In addition these WLAN issues may have different reasons. Also, a bad WLAN configuration would be possible. So, you should check the WLAN settings and configuration of the router. Also, an update of the firmware on the router could be useful.

• Unable to get Internet using modem internal dial on Equium A200-15i

  Using my new laptop EQuium A200-15i while a Wi-Fi by Netgear has been created, I could not get the internal modem to dial up to my ISP on PAYG (to serve as a backup in case of need).
  Device Manager indicates the modem is not working properly and the driver is up-to-date. The number of dial ISP (Virgin) is also correct - I can connect to the internet using the same number of ISP of my desktop computer.
  I think I put in place the ISP connection correctly - I get a ringtone of the laptop but every time can not pass and a screen of failure rises. Y at - it still configuration of Toshiba laptop that is needed?
  The modem would be defective? Is there a technical contact E-mail for Toshiba
  Any ideas?

  Hello

  In the first post you talked you a failure screen which appears after the failure of the modem connection. Could you please post the error message?

  In addition, it would be desirable to set up the Modem region selection utility that should be in programs-> Toshiba-> Networking folder.
  Delete the old profile and create a new one.

  Good luck

• Need to drive recovery for Equium A200-15i

  I'm a noobie and posted this query in the box Equium, so apologies for swap. I bought an Equium A200-15i computer about a month ago. There was _no_ recover CDs in the box just the Windows Anytime upgrade disc. I contacted the store where I bought the computer to be told to put in the computer and they would take the details of it in order to create or order the CD. I did this and then said that they would have to wait until 'a guy' is established at the end of week, who knew how to create these discs and back again once then.

  Because of the great distance involved in travel, I was reluctant to make a second trip to the store and suggested that if they take all the details of the computer now, they should be able to create this disc and then after it me. I still have not received this drive at all. Now at the same time, the guys at 'tech' in the shop said they believed that I wouldn't need a CD master. In addition, they imply that it should be possible to create this disk myself at the first start-up or windows environment itself. I do not remember this option of provision for me at this time and I can't find anything on the computer that would allow me to accomplish such a task.

  Here, I'm confused. I know not enough about computers to realize that you need a Master CD to recover a system failure major hard drive or simply to clean and re-all over again!

  What are your thoughts on this situation? Should this model really a MAster CD. How do you create one. What should I do next? Thanks for your time and your patience with me on this

  null

  Hello

  I wonder why you did not receive the Toshiba Recovery CD with your laptop.
  I'm 100% sure that the CD or the DVD should be bundled with the laptop Toshiba together
  I put t know if the package was already opened or not, but the DVD must be available!

  SO either you go ask your original dealer of laptop to a Toshiba Recovery CD or simply contact you the Toshiba ASP and will be stopped a new!

  Concerning

• Equium A200 15I audio don't deliver - C00D11E5 - no speakers error code

  Hello

  the speakers of my Equium A200-15I went suddenly silent. They speak too low. It is not cut and the control managers say that it works correctly.
  It works with some other external stakeholders. but my speakers before you say anything. the error code I got is C00D11E5 with media player.

  Help please

  This error is not known to me and it seems that there is not a lot of people with questions of the error
  First of all, you should try to remove you sound driver should and then reinstall again.

  On the Toshiba page, you will find the compatible driver.

  The question remains then you should recover the laptop with the Toshiba Recovery CD. Usually, if your notebook malfunction s material doesn t then a recovery CD should solve this problem. Otherwise, the hardware may be faulty and the laptop everything should be checked.

  Best regards

• How connenct Equium A200-15i to TV?

  Hello people,

  Recently joined and impossible to find answers to my question about the right of cable should I use for me to be able to transfer some pictures (movies) from my laptop to my tv.

  My laptop is model TOSHIBA EQUIUM A200-15i and has only a port external moniter of 15 pins.
  My tv has a PC ready to and has a 15-pin and HDMI ready as well.
  I have no idea at all how to work with the cable, I read somewhere that some cables is simply play with the video but no sound.

  Can anyone of you can help me this type of cables should I expect and works with my laptop and TV.

  Any advice is welcome... Thank you

  Hello

  Seems that the laptop would support the s-video output port.
  So you can use an s-video cable (s-video-to-SCART or s-video-to-s-Video) in order to connect the laptop to TV
  Of course this depends on your TV this cable you will use, but AFAIK most TVs support a cable SCART so

  Welcome them

• Equium A200-15I - need part number of battery

  Hello

  I have a laptop Equium A200-15I and its original battery has been lost. I want to buy a new one, but I need to know the part number of the original battery.

  Any body know what is the part number of the original battery?

  Thank you very much

  Toshiba offers several batteries 6 different cells for this old Equium and they have a capacity between 4000mAh and 5800mAh.

  Here is the list:

  4000mAh - PA3534U-1BRS/1BAS
  4000mAh - 1BAS/PA3522U-1BRS
  4400mAh - 3BAS/PA3285U-3BRS
  4700mAh - 5BAS/PA3191U-5BRS
  5200mAh - 1BRS/PA3594U-1BAS
  5800mah - PA3612U-1BAS/BRS

  If you have any other questions you are welcome.

• How to create Master records for my laptop Equium A200-15i

  I recently bought a laptop Equium A200-15i. How can I create a CD/DVD Master can I use to restore my computer in the event of a major failure. I know all about the restoration of the machine of the hidden partition, but I want to get my hands on the DVD to use in case of a major failure of the system.

  I took my computer to the local computer store to highlight the fact that ther were no Master DVD as part of the packing list and they seem not very useful. I bought a lot of computers before and normally those two things are provided to the user, or there is a facility for the user to create a. Thanks for your help.

  null

  Hello

  Sorry to hear that, but I hope you can get the original DVD for your laptop. If the PC store will not help you please contact authorized partner in your country and explain the situation.

  They can order one for you.

• How to use the resolution to 1280 * 768 on external TV with Equium A200-15i

  I have my laptop Equium A200-15i hooked to my Bravia HDTV which accepts entries to 800 * 600, 1024 * 768 and 1280 * 768.
  But my laptop will be released only in 800 * 600, 1024 * 768 and 1280 * 600 and I want to use the full screen on my TV.

  I read a few other posts on this subject and I think that the problem lies in the BIOS, and I've not being updated since I got it in September, but I was wondering too since I'm Dual-booting Vista and XP pro, there will be problems with the BIOS I download?

  There seems to be two more different for Vista and XP, who apparently get along out of each other.

  Finally, update the BIOS problem will be solved my monitor extended?
  And updated the BIOS using the BIOS XP Download break my laptop/vista partition?

  Should I just not bother with the Dual-boot and go Vista/XP only?

  Thanks in advance

  The BIOS is not the problem!

  The fact is that your display driver doesn't support the resolution of 1280 * 768, and so you can't choose it.

  Once again;
  > Finally, update the BIOS fix my extended monitor?
  No, as I said above, you can't choose your preferred resolution because it s not included in the graphics driver.

  > And updated the BIOS using the BIOS XP Download break my laptop/vista partition?
  No, but if Vista is installed on the laptop then I advise you to use the version of vista BIOS.

  > Should I just not bother with the Dual-boot and go Vista/XP only?
  Dual-boot is recommended according to me ;)
  I have dual boot on my second notebook too. Dual boot has many advantages...
  As you know from the beginning of the applications don't run correctly with Vista and if you have installed XP then you can run it without big problem ;)

  Welcome them

• Should I in fact this recovery DVD - Equium A200-15I

  Hello

  I have a laptop Equium A200-15I series. For reasons too long to describe here, I don't have the DVD of master restoration - it was not provided with the product and after that a long period, I was told that I would have to pay for it. Not fair, but there you go!

  My request is that the hidden partition on the laptop is still there and what I want to know is that can still recover my windows Vista environment by hitting the F8 key at startup upwards and crosses the screen of recovery without the DVD Master procedure or do I absolutely this disc.

  I am aware that all media that comes with the DVD won't be available, but this isn't a problem.

  I hope someone can help

  Best regards

  Hello Seamus

  To be honest, I'm a little confused, and at first, I just want to clarify something. Notebooks (A200 series) are supplied with recovery DVDs and these books have no recovery image on the HARD disk and you cannot install the OS by using advanced startup options (F8).

  New laptops like A300 models are supplied without recovery media and recovery image is saved on the HARD drive and there is a possibility to install the OS without recovery DVDs. The recovery image is saved on the second partition in HDD Recovery folder. Drive HARD recovery can be done if this folder is not removed.

  If you want to have the factory settings again you need recovery (DVD) image. You can also purchase Microsoft Vista DVD facilities and install your own operating system. All the drivers, tools and utilities that you can find on Toshiba supports the page. Of course some other software like Norton or WinDVD player are not downloadable.

• Equium A200-15I - how to install more memory?

  My memory in my Equium A200 - 15I SERIES is at MAX, what is.

  How it came to new 2x1GB can these be removed and install more memory

  Hey hun01,

  I searched a bit using Google and the Equium A200-15I is equipped with an Intel 943GML chipset and this means that the laptop can use up to 2 GB of RAM (2 x 1 GB modules).
  If your laptop is already equipped with two 1 GB modules you can t upgrade it and if not you PC2-5300 modules to upgrade your laptop.

  In addition, you should also check the user manual where you can find additional information about it.

• Equium A200-15i: I can't use the touch pad - no response

  I can't use the touchpad in my equium A200-15i.
  When I press the button, there is no response at all.

  Please help me to solve it.
  I tried to uninstall the program and reinstalled, but the problem persists.

  Hello

  Have you checked if the touchpad is properly activated?

  Using the FN + F9 key combination, you can disable and enable the touchpad feature!
  Please check this function if you have not disabled the touchpad accidentally!

  Last but not least, I would recommend checking settings the touchpad mice control-> Advanced-> advanced settings panel.
  You will find different options that can be configured to use all available touchpad features.

  Best regards