Re: Portege M750-11 t - connection is unstable

Hello

I had a problem with my Internet connection on M750 almost since the beginning.

What is happening is that the connection is unstable. I had difficulties to simply connect with a cable, with Wifi too. But wireless seems to work well. Also, when I run a diagnostic of the device everything is ok but it says that there is something on the Internet/network.

Hello!

> Also when I run a diagnostic of the device everything is ok, but it is said that there is something on Internet/network
What diagnostic program did you use? Windows?
If Yes, you should put the exact description because it might be useful.

At the moment it is really hard to tell which is the reason why, for this, but in your case I would start to update the drivers and update the firmware of the router.

On the Toshiba site, you will find the latest drivers for your laptop:
http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

Good bye

Tags: Toshiba

Similar Questions

  • Portege M750 Win7 64 bit Wireless Manager (3G) will not work

    I can't TOSHIBA Wireless Manager (3G) to work in a new installation of Win 7 64 bit.

    I did a test installation of Windows 7 64 - bit on and old SATA hard drive and checked TOSHIBA Wireless Manager would work. He did.

    I then did a fresh install of Windows 7 64 - bit on a new Crucial C300 Real SSD 256Go.

    The new facility with the Crucial SSD is not very successful... The operation "stop and restart" does not - the closing not always power off completely and you must push the switch down to.

    Sometimes the SSD does not start - you enter the password of the BIOS but then nothing happens. Sometimes you turn off the power and remove the battery before as the startup disk.

    But the biggest problem is that the (3G) Wireless Manager will not work. The application opens and indicates that "died" - which it is impossible that I use WiFi to post this question.

    I tried to install the software Vodafone 3 G portal. It detects the presence of the 'mobile device' (SIM in housing) but then can not turn it on.

    I downloaded and installed all the latest drivers for the chip, the pilot 3G, 3G software, LAN driver, LAN software and all updates of Windows 7.

    I have the latest version of the BIOS (3.0) but this has not been updated by Toshiba since 11/04/09.

    I would point out that Diagnostic PC Toshiba tool does not recognize the installed 8 GB memory (but ccleaner):

    Model name PORTEGE M750
    Part number PPM75E-00N017EN
    Version of the OS Microsoft Windows 7 Home Premium 6.1.7600
    Version of the BIOS Version 3.00
    Processor Intel (r) Core (TM) 2 Duo CPU P8400 2.26 GHz
    Physical memory 4096 MB RAM
    Disk capacity hard 256,052,899,840 [bytes] 238.468 [GB]
    Network Intel(r) 82567LM Gigabit Network Connection = 10.0.2.2 version = MAC address
    TOSHIBA F3507g Mobile Broadband Network Adapter version 1.3.0.9 = MAC = address
    Version of Intel(r) WiFi Link 5100 AGN = 13.4.0.9 = MAC address
    F3507g Mobile Broadband Modem Modem TOSHIBA version = 5.24.3.0
    Internet Explorer 8.0.7600.16385

    This indicates a BIOS problem?

    -don't

    points to a problem of firmware on the SSD drive (is it sandforce) torque to the incompatibility of BIOS of the SSD.

    I assume that all drivers installed etc were identical on the installation of the trial of HARD drive? so if this is the case it must be the SSD does not not with the BIOS correctly, so the other issues as well

  • Mobiel Breedband WWAN / 3G in Portege M750

    Hello

    I have a UMTS start XS4ALL mobiel internet key usb. Can I use this SIM card about slot the battery of my Portege M750 (Mobiel Breedband WWAN / 3 G (HSDPA 7.2 Mbps / HSUPA 2 Mbps))

    And how do I then an internet connection?

    With greetings
    Wilbert

    Hello!

    I m not an expert, but you can use the SIM card in each location that is designed for SIM cards so I'm pretty sure it will work.

    I'm not sure, but normally you should get a driver disk or something else with the stick. Check and install the software on the drive.

    Good bye

  • Portege M750 and 3 G/GPS

    I have a Portege M750, inserted a Sim Card into the slot behind the battery, but I can't connect. It detects my local network (Vodafone), I have a level 3 signal but when I click on "Connect" it tries to connect and fails. The weird part is that whenever I try to connect a LAN connection icon (like trying to acquire the network address) and then a bit of balloon pop up the message "connection to the network of Local 4, a network cable is disconnected. Then give me some ideas on what to do.
    And I would ask if it is possible to connect to the GPS. I have a navigation program (IGo 8 for pc) and I want to connect the GPS.
    Here is a list with my system features:

    Date 06/09/2009-16:06:29

    [Information on PC]
    Model name PORTEGE M750
    Part number PPM75E-00S00JG3
    Serial number Y8096960H
    Version of the OS Microsoft Windows XP Professional 5.1.2600 Service Pack 3
    Version of the BIOS Version 1.80
    Processor Intel (r) Core (TM) 2 Duo CPU P8400 2.26 GHz
    Physical memory 4096 MB RAM
    Disk capacity hard 250,064,962,560 [bytes] 232.891 [GB]
    Capacity of the hard drive space free 178,133,031,424 [bytes] 165.899 [GB]
    Version Mobile Intel (r) 4 Series Express Chipset Family video = 6.14.10.4953
    Screen resolution 1280 x 800 Pixels
    Color quality, true color (32 bit)
    Audio version of Realtek High Definition Audio = 5.10.0.5804
    Network Intel(r) 82567LM Gigabit Network Connection = 9.52.25.0 version = 00:1 MAC address: 7E:25:7 A: B5
    Version of Intel(r) WiFi Link 5100 AGN 12.4.3.9 = MAC = 00:21:6 B address: B6:C4:3E
    F3507g Mobile Broadband Modem Modem Toshiba version = 4.50.2.0
    IDE Device 1 Hitachi HTS543225L9SA00
    2 IDE devices MAST * a DVD-RAM UJ862AS
    Interface IDE 3 no
    Interface IDE 4 no
    Interface IDE 5 no
    Interface IDE 6 no
    Internet Explorer 8.0.6001.18702

    EC/KBC Version "V1.10.
    PS-MICOM Version "V1.00.

    Hello

    Don't know what's going wrong for you, but you can try the latest drivers/Toshiba Wireless Manager.

    Drivers:
    http://Support1.toshiba-tro.de/Tedd-files2/0/3gdrv-20090130131934.zip
    Wireless Manager:
    http://Support1.toshiba-tro.de/Tedd-files2/0/wlmng-20090331151350.zip

    I'm not familiar with IGo 8, but if she supports the NMEA data to the serial port, it should work.

  • Portege M750 - replacing the CMOS (RTC) battery

    Hello world

    I have a Portege M750 model PPM75A-007010 and I need to change the CMOS (RTC) battery.

    If someone can share with me
    -where to find this battery
    -is normal around the battery and if you can tell me the number of battery?
    - or where I can buy this battery and price range?

    Thank you
    RC.

    Hello

    Normally, the RTC battery in these models are rechargeable.
    If not already done, please leave the unit on for the night (not disable, not extended, not sleep - but ON) and see if the problem is resolved.

    I think the accusation-description/also the RTC battery is mentioned in your user manual.

    Tom BR

  • Portege M750 PPM75E Windows 8 drivers - SOLUTION

    Hello

    I just wanted to leave a message with the solutions that I found for different applications for Portege M750.
    These are the applications that I use the most,
    so if you need other drivers and applications just leave a reply and I'll try to find it.

    _Got work: _
    Pilot Bluetooth and 3G and GPS ([Toshiba Europe | http://eu.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp?service=EU])
    Keys, except the button Assist de Toshiba and presentation.
    Both opens it: [buttons | https://skydrive.live.com/?cid=0b5d644d977b4b3a&id=B5D644D977B4B3A%212226&sf f = 1].

    What I find more useful then the old functions.
    Installed value-added package, I think that from here: [go to the download section: http://www.csd.toshiba.com/cgi-bin/tais/support/jsp/modelContent.jsp?modelFilter=M750-S7213&rpn=PPM75U&category=&selCategory=2756709&moi d = 2266999 & os = & ct = SB & selFamily = 1073768662]. The website of europe has failed.

    Utility of fingerprinting.
    Control Panel-> user accounts and the safety of the family-> user accounts and you have an option in the left side of the window for fingerprints. Install the drivers and programs, works like a charm. Or search on google for TrueSuite

    For the ctrl + al + arrow down to reverse the screen, I used iRotate (google it).

    Still no solution for the protection of HARD drive utility, again.

    Many drivers Win7 would work with system Win 8.
    But there are still some drivers and utilities which are not entirely compatible.
    I have a tip for you:
    As far I know the HDD protection as utility isn't a model of related software.
    You can try to install Win 8 HDD utility out to protect Z930 protection

    It would be really interesting to know if it works.

  • Portege M750 - 2nd HARD drive in the Bay select instead of optical drive carrier

    I just bought I used Portege M750 because my M700 was broken. Unfortunately, the berries to choose between the two models are not compatible. Although the availability of a 2nd drive hard trolley is mentioned in the user manual, I couldn't find the part of the disk for the M750 caddy. I tried a standard SATA-SATA HARD drive caddy, but I get a message "select Bay error" at the start, although the caddy runs under windows, as long as you do not hibernate.

    Does anyone know the part no of the real 2nd hard drive for Portege M750 caddy / M780? Or is there another 2nd carriage of hard drive that works with the M750 without restriction?

    Hello

    I guess that you will need a hard drive caddy part number: P000452980
    Then you could place this in the Toshiba Ultra Slim PA3408U-2CTE and PA3408U-1ETC HARD disk adapter

    But you can also contact the Toshiba ASP in your country to get a confirmation...

  • Portege M750 on plu III Advanced Port Replicator

    The Portege M750 works on Advanced Port Replicator III more (PA3474E-1PRP)?

    Hello

    I discovered that the Express II port replicator is compatible with the Portege M750.

    I searched a bit on google and found this link to an Advanced Port Replicator III over the datasheet. But it s only in German.
    http://www2.inmac.de/inmac_assets/PDF/German/e569412_datasheet.PDF

    However, the M750 Poretge is not listed as a unit compatible and taken in charge.
    So I guess that more Advanced Port Replicator III cannot be used with protected M750 toghterer

    Welcome them

  • Need drivers Vista for Portege M750

    Anyone know where to find drivers for VISTA for my Portege M750?

    You have a model European or US?

  • Portege M750 - change from 32-bit to 64-bit

    I just bought a laptop Portege M750 which is preinstalled with Vista Business 32 bit and separate tablet XP on a recovery disk.

    I await with resinstall with 64-bit Vista business, then install the XP as part of a system to dual-boot to take full advantage of the 4 GB already installed in memory extension and more in the future.

    My question is this: Although the drivers Toshiba download page does not specifically list a Vista 64 bit OS, no matter who made a similar change of OS on a Portégé / or other laptop and had all incompatabilty with applications and 32-bit drivers? If so, what drivers/features have caused problems later.

    The "Toshiba" folder in the notebook computer C:\ directory contains all of the drivers and install files required or these all need to be downloaded from the Web site.

    Thank you

    Hello

    Usually, 32-bit divers are designed and created only for the 32 bit OS and usually they would not run on 64 bit OS. But who knows, maybe some unique drivers would be compatible with 64 bit but it is more than questionable.

    > Does the folder "Toshiba" in the directory C:\ for laptop computer contain all drivers and install files required or these all need to be downloaded from the Web site.
    Generally all Toshiba drivers can be downloaded from the page of European driver of Toshiba.
    Toshiba on C file can contain only the installed tools and software.

    See you soon

  • Who are the real or compatible cards for the Portege M750-109?

    Hello

    Anyone know who is the number of the actual card for the Toshiba Portégé M750-109?

    I wonder if the PA3283U-1ACA iscompatible.
    (15V) voltage and amperage (5V) are the same, but what about the decision-making that plugs into the laptop?

    Can someone explain the significance of the various characters in the nummer adapter?
    For example, the difference between a (-1ACA) and a (-3ACA), a.s.o..

    For 200V cord, country differences are not a problem, I can get the power supply one another.

    But I need the adapter and its taken low voltage to be compatible with the M750-109.
    So, how do I identify what Toshiba cards are compatible?

    Thank you very much.

    Supports the adapter used for Portege M750 * 15 Volt ampere 5 *.
    You must use a power adapter that supports 15V too!
    This is very important!

    The value of intensity can be a little different but too low because in this case the laptop would not get enough power!

    > Voltage (15V) and amperage (5V) are the same, but what about the decision-making that plugs into the laptop?
    The 15V AC adapter should be the same

  • Portege M750 and Win8.1 Pro - the tablet buttons do not work

    Hello

    I have problems to install the tablet buttons in WINDOWS Pro 8.1. Everything else works perfectly.

    In Windows 8 Pro this button worked fine, but now, after clean installation of Windows Pro 8.1 two buttons do not work. The buttons are the Toshiba help buttons and the presentation. I tried to set them up in Toshiba assist software but nothing happens.

    I don't know that I have installed all the drivers who wverything work with Windows 8. Someone at - he tried this and add success?

    > I don't know that I have installed all the drivers who wverything work with Windows 8

    Windows 8.1 isn't Windows 8 and many tools and drivers Toshiba win 8 don't work or are not fully compatible with Win 8.1

    As much as I know the Toshiba can't win on this Portege M750 8.1.
    This means that no Win 8.1 driver will come out and in this case, certain features of the laptop as the control buttons may not work properly.

    You are using Windows Vista or Win 7, these buttons were controlled by added value package. This package does not exist to win 8.1 and has been replaced by other software called system Toshiba driver

    So in case you want to try to get to the buttons, I recommend that you check this with Toshiba system driver

  • Portege M750 and Win8 - metro and touchpad interface does not work

    For those of you who, like myself, tried to install windows 8 in a Toshiba Portege M750 and had problems in tablet in portrait mode I recommend the following driver, it works perfectly:

    http://CDN.Wacom.com/U/drivers/TabletPC/ISD_DualTouch_710-8.zip

    The problem that I had was that shot didn't work with the metro interface and touch works also and in portrait, strangely, when you touch the secren with different directions woul two arrows appear.

    This driver solved my problem.

    Hope this can help...

    Thanks for the info.

  • Portege M750 - how to use Windows 7 gadgets with 3D sensor?

    Hi all:

    Portege M750 has several sensors on the inside (3D, accelerometer and GPS sensor). Enybody knows's Windows 7 gadgets based on these sensors, as a horizon of aircraft or other?

    Very interesting question.
    Have you also tried to ask this question on the forums of Win7?

  • Portege M750 - how to upgrade to Windows 7 without preinsatlled Vista?

    I have a laptop Portege M750 who had professional Vista on this subject.
    I removed vista and installed the RC of windows 7

    Now I have received the final windows 7 vista upgrade but can not install via Win7rc or independent to have vista first.
    I don't have a cd of vista for the laptop as it came only with the CD of windows xp for some reason any.

    The recovery partition has been deleted when installing win7 rc
    I'm downloading a torrent of vista that should work, but is a few hours

    I was wondering if there is another option for the upgrade of windows 7 to install

    Hello

    You cannot switch to Win 7 without Vista operating system preinstalled.
    In this case, you can do ONLY a clean installation of Windows 7.
    But for this, need you a Win 7 DVD and not an upgrade disk.

    I think that the laptop has been pre-installed with Vista and there is a possibility to create a Vista recovery disk.
    (but in addition you get a Win XP disk in order to have two operating systems).
    Looks like you do not have create this Toshiba Vista recovery disk using the Toshiba recovery disc creator (must be preinsatlled on the laptop), which means that you will not be able to reinstall Vista new

    I think that there is nothing to do but to buy a Windows 7 disc and do a clean install.

Maybe you are looking for

  • What word processor with a Macbook Pro?

    What treatment should I use with a Macbook Pro (2010 with El Capitan)? There are freebies? I use it a lot.

  • HP envy 15t: HP envy 15t laptop does not turn even after going through all the recovery solutions, I've seen online.

    My notebook of HP envy turn not, I plugged in the charger and the indicator showed a white light for a few seconds before changing to an orange light. Let charge for a long time and still have the same problem. Please I really need help.

  • Repair service

    Service station took my laptop to fixing a problem. The fault was that the screen would be almost completely black intermittently. They return the laptop after for between 1-2 days. Apparently they fixed something (I don't remember the exact terminol

  • charging problem air iPad

    I did not use my iPad in the last two months air. It has been turned off. Yesterday, when I tried to use it, it was not open and showing an empty battery. But it's not have charged. When I try to load my air of iPad, it shows the sign given in the fo

  • Memory resize with change 0-, it slows the calculation?

    I'm adding two arrays with elements 1e6; the addition of loop 1000 times. When I use the review buffer allocation tool, it shows a buffer allocation to one of the entries on the node to add. When I trace the performance, he reported 1000 memory resiz