Re: Satellite 2455-S3001 - LCD no longer lights

Similar Questions

• Satellite 5100 - LCD screen no longer lights

  Hi, I hope someone will help me on this problem.

  After disassembly of the top satellite covers the lcd screen that does more, but I guess the system is working properly because I can hear windows access "jingle". I think that I reconnected it all cables (green and white connectors for the video card), but I'm not sure thin brown/white/black cable of the lcd screen. That's all

  Hi stefano88,

  Why you have disassembled the LCD?

  To be honest I n don't know cables, you want to say you also plugged the UPS FL for LCD display? This is necessary because FL inverter controls the backlight of your screen.

  Can post you a photo of the cables you want to say?

• Satellite M40-265 LCD displays the image complete but crushed

  Satellite M40-265 LCD displays the image complete but crushed on two-thirds of the screen

  When my Satellite M40 - 265 ATIMobility Radeon X 700 and omega 3.8442, Windows Xp drivers, Sp3 boots by setting the LCD + analog RGB, initially only displays on the external screen after startup can be switched with Fn + F5 on LCD. Then appears on the LCD, the complete picture but only two thirds of the screen, third, the right is black. It works so well when the external monitor is not connected during the boot.

  When defini set to auto, select the display to the computer starts only when an external monitor is connected, then after that, I spent in the LCD screen.
  Damage to the inverter is excluded as already checked. Inspect visually the cable of the LCD displays nothing. Beside the left speaker, a ground wire (black) to screwed, but it is s t connected anywhere.

  Starting in safe mode is possible to use a display fullscreen on external

  Hello

  The M40 is a not sure oldie about the available settings in the BIOS and in the graphics options, but I think you should check the settings of the graphics card ATI Catalyst.
  I remember that ATI catalyst supports certain options such as resizing the Image. Here you can select the image scale Panel option full size
  In addition, you must set the resolution on the internal screen at native resolution of 1280 x 800
  I think that the external monitor supports the resolution, which is not the same thing as the screen internal.

• PX4 - 300 d starts more-white LCD, power flashing light

  My PX4 - 300 d has been quitely sit in a closet, storage of files. I don't have access to well over a month. I set it up maybe 2 years ago so I am only guessing at the RAID config, but I think it's a 3 X 750 GB RAID 5 drive.

  I tried to access the share and failed. Ran a scan IP to see if I had the wrong IP and he could not stand. Physical control it and I saw that the LCD screen is light blue, but empty, and the power led flashes.

  I rebooted - nogo.

  Drawn from all the readers and restarted - nogo.

  Pulled all the readers and the hit the reset in the back (just above input AC) - nogo.

  Fans spin, LCD is bright blue (but still empty) and the power button flashes.

  Next step?

  Hello mrmatarazzo,

  If the NAS does not start with the deleted readers the only option is to open a ticket of support here:
  https://Lenovo-na-en.custhelp.com/app/ask/

• Satellite - only no longer lights

  Last night our new Satellite computer has stopped working. Tried to restart.
  Held On / off for 10 seconds, plug plug out and the battery for a few minutes and tried again.

  It would seem is powered, as 1 and the Middle LEDs are lit on the front of the computer.

  When I press a stack button light goes orange then to white, and computer will not start.

  Any ideas?

  Hi Al Hendo!

  Can you please tell us what Satellite phone you have exactly?

  I m do not know what it is because I m not a technician for laptop, but I think that this problem is hardware related and you need professional help of an authorized service provider. Technicians can repair the laptop for you.

  I'm pretty sure that an ASP can help you more than the users here. ;)

• Satellite A300 - the word Satellite no longer lights

  Hi, I have a little problem with my laptop A300. On the lower left corner of the laptop, it says the word Satellite. It is still used to brighten up this time for some reason any, that it doesn't. I change all the parameters that have made this place. Did the light die on me already after less than 4 weeks? Or maybe there's a way to turn? It's obviously something small, but it irritates me.

  Thank you.

  Good news!

• Satellite A100-788 - LCD turns black-shadow

  Hello to all specialists!

  I have a problem which became unbearable with the monitor of my Toshiba A100-788. When I turn on the laptop for a few seconds, works normally but would then become black and everything is in black shadow. I can see what is on the desktop if I put a strong light in front of my screen. until the monitor worked if I restarted abruptly the laptop but now no longer works. I already replaced the LCD inverter but I have the same problem (should I replace the inverter wires?). and I have already connected to an external monitor and working correctly. I'm a little desperate because I need the documents on my laptop.

  Help, please!

  Thank you!

  Hello

  It looks like a FL. inverter problem

  The FL inverter is a piece of equipment behind the frame of the LCD and this material part controls the LCD backlight.

  In my opinion it s broken and it of necessary to replace this part in order to solve this problem.

  I would recommend contacting a local Toshiba ASP. Guys should help you to replace this part.

  Good luck

• Satellite A350-12j - cannot turn off light Mediabuttons

  Hello

  I bought a Toshiba Satellite A350-12j, and I think it's a fantastic phone!

  2 days ago after about 3 months of use, it began to slow down, so a friend of start me 'Cleansing' of my laptop. (Some progs antispyware, CCcleaner, defragmentation, run..) and it also took some start programs op in the MSCONFIG.

  After this cleaning, we installed AION and it runs great, computer is fast, once again, all good. Until last night, when I was ready to put the buttons of media and the Strip-light little above the touchpad and the Toshiba brand out, so my battery would last longer, it has stopped working.

  Whenever I press the icon to boot, only this icon turns off and then the lightning is reactivated. It sounds like a stupid problem, but it lowers decreases your battery. Now, I checked back on in the MSCONFIG and already ran a repair of the system, but nothing seems to help...

  Can someone help me with this stupid problem please :)

  Friend, Niels

  -Sorry for my bad English, I'm from Belgium-

  Hello Niels

  Open it please help Toshiba > Optimize > Toshiba hardware settings.
  If I remember well there must be tab on lighting and the option toggle.
  Check please if it will works.

  You can also try is to remove preinstalled value-added package and after restarting the laptop installed the latest version, you can find on the Toshiba support page.
  I'm sure that you'll be able to control the new lighting option.

• Satellite A100-906: display no longer works

  Hi all
  For me Satellite A100 with NVIDIA GeForce Go 7600
  I met such a problem. LCD monitor from another manufacturer via D - Sub is connected to a laptop computer.

  Mode used ForceWare customizations DualView, for the display of a laptop exposed the screen resolution 1280 x 800, for LCD screen accordingly 1680 x 1050.

  All worked normal before restarting the system. After restart, the screen of a laptop computer disappeared and does not any longer, it is only visible, this highlighting of a matrix works. A computer screen laptop not everything works more generally, the lamp to highlight show, even to the external display disconnected.

  Please advise something!

  What happens when you disconnect an external monitor and the power of your laptop? See Toshiba welcome screen?

• Satellite R830 not working - flashing power light

  Hello

  My Satallite R830 lights.

  The power symbol flashes orange 8 times then pauses and restarts. There are 6 quick flashes followed by a longer 7 flash then another quick. The symbol wireless is lit (orange) all the time.

  If I unplug the laptop and remove the battery and hold the restart button for 30 seconds then without taking the battery in the charger stops flashing and the symbol of the power goes to green, until I try to turn it on, it has a fraction of a second where it looks like it is starting then stops and flashing orange again.

  Same thing if I unplug the AC adapter and the battery and then tried the above, but with battery or ac charger.

  I tried with another adapter (same output amp and volt).

  Can anyone help?

  Thank you very much

  Post edited by: sivyer2081

  > 6 quick flashes followed a longer flash 7 and then another a quick

  If the power supply microcontroller has detected an error lamp DC IN sends a blink code.
  The short means 0 and a long time means 1.
  I have your case, that means: 0000 0010

  Because the error code starts with LSB (least significant bit) to read it from behind
  -> 0100 0000 0000 0010-> 40 H (hex)
  Now, you will need to know what means 40 H

  After a few details that I found on the internet, the 40 H could be the fault of S3V output. (S3V voltage is more 3.47V)

  However, such errors are mainly related to the problem of the motherboard (internal circuit problem) and from my point of view of the party only a few replacement may fix this error.

• 32D1334B LCD TV - not light power light flashes red & Green

  I have a Toshiba 32D1334B LCD TV, it used to work perfectly well and then all of a sudden, it will not activate.
  When I plug in the TV, the power automatically light flashes red and green permanently. There is no way to turn on the TV; the screen remains black.

  I had to take off the back, watched and deleted all the parts, but can not see the obvious problems. I also a multimeter and power to the various sections of the TV is, but that's as far as my electrical knowledge goes!

  I don't really know what else to try, but I am very reluctant to throw away the TV that I know it's probably a unique piece that needs to be replaced to fix it. I searched online and others have reported the same problem exactly, but it had not resolved there always. Unfortunately, TV is more under warranty... If anyone has any suggestions or can provide any help, then it would be greatly appreciated!

  Thanks in advance.

  If you find out how to fix it please let me know because my tv is the same.chris

• Satellite PRO U500 - LCD screen size is reduced

  Hi all,

  I have a Toshiba Satellite Pro U500 with one small problem, the size of the LCD screen is reduced. I have a white border to the right and down. The max resolution is 1024 x 768.
  The problem is visible also when I enter the BIOS, so I think that the problem is not Operting System drivers.
  Is there a solution to my problem? I have to send in the audience?

  Thank you for the help
  Giuseppe

  H

  It is really strange, especially if you see the same thing in the BIOS settings?
  Since when did you notice this behavior?
  Do you use pre-installed OS original you got with your laptop?

  Have you done something that may be responsible for the issue described?

  I U500 and default display resolution is 1280 X 800 t, so I understand why you have 1024 X 768 on your U500.

• Won't boot satellite R850 Pro - fan snoring; power light cycles; NumLock on

  My R850 Pro Satellite won't start. When I press the power button the power light on the laptop (under the mouse buttons) travels flashing green, green, orange, orange and the snoring of fan. also the Verr Num led on the keypad is turned on and won't go off in such a hurry. The screen is blank and plug a monitor displays a white screen.

  Remove the battery has no effect, the same results as with.

  The hard drive is readable went out and attached to the other pc as external drive using a shopping cart.

  Any ideas on what to try, hope someone can help you.

  Thank you, Carol

  You see a Toshiba splash screen at the beginning?
  You can access the BIOS?

  If this is not possible, a serious hardware problem appeared...
  It could just be a memory, but in the worst cases, your motherboard is the problem

• Satellite A300-1IW: HARD drive access light blinks every second

  Hello everyone, and sorry for the English, I'm french :)

  I bought a Satellite A300-1IW a few days and suddenly (don't remember exactly when) early light access HARD drive blinks every second and it continues even after several reboots!

  It does so only with Vista; I checked the disk with 'diskmon' activity and I saw that even if it was * no. * disk * written * or * reading * the led continues flashing, so I think that it is not bound to certain services of vista (superfetch, indexing...)

  A similar problem, I saw on a Microsoft support, but it was under windows 98 and with old motherborads!
  See: link: [http://support.microsoft.com/kb/138598]

  So it seems that it is related to level Vista SCSI or DVD...

  I have now is not critical, but it's annoying to have this led flashes all the time

  You have an idea? Don't you think that it could be related to bios? I want to be sure before touching it, because it is always tricky.

  Thanks for your help

  In my opinion, nobody can offer no comment because you already gave the answer. There is nothing unusual and certainly no reason to panic.

  What do about it? What you want to do? Sorry, but this is a really stupid question. I can just offer you a stupid answer. ;) Take black tape and curl up the LED. ;)

• Satellite Pro A120 - LCD black screen - Fine on external monitor - fine

  Hi, I have a headache with a Toshiba Satellite Pro A120 mojor. The screen began to move to the blackout at random times and happens more and more. It is not serious if W
  Jayindows has loaded or if I enter the bios, boot from the CD or leave it sitting waiting for me to select a boot device. More often than otherwise, it becomes black, but you can still see what needs to be on the screen, it is simply not at all turned to see clearly. The laptop itself still works very well because it works on an external monitor and makes the system beeps, cd turns etc.
  Have you tried the following:
  Setting of various parameters in the graphics properties and in the bios but makes no difference.
  It also becomes active again if I press FN + F5 to swap monitors but turns off after a few seconds.
  It is not overheating as it's been all night and still sometimes happens when starting Cold Stone.
  I tried to start with / without battery - no difference.
  I tried to start without the disk HARD - no difference.
  I tried to remove the battery by pressing power for 60 seconds, then add the battery and new starter - no difference in power.
  I could have sworn it is the inverter, but it does the same thing with an inverter I know works! do not think that it may be graphic because it works on an external monitor and turn off.
  I'm out of ideas and looking for a genius to fix it for me please!
  See you soon

  Hey Buddy,

  > It turns on but not at all to see clear
  This would mean that the FL inverter is faulty the FL inverter of the internal LCD display controls the backlight of the screen and if the isn t working FL inverter you can see a picture, but very very dark.

  It would be a logical explanation for your problem, because there must be something wrong with the laptop LCD if an external monitor is working properly. Also if it happens in the BIOS the problem is not software.

  In your case I contact an authorized service provider and ask the guys for help. They can check your laptop and this should be done. Here, we can only speculate and discuss the different possibilities because it s just a user forum. EPA has professional diagnostic tools and can order all Toshiba spare parts.

  Good luck! :)