Re: Satellite A300-29n - blue screen appears during installation of XP?

Similar Questions

• Why a blue screen appears during installation of Windows 7 and not setup any OS?

  Dear support team,

  I have a Compaq Presario model: CQ3132L; Product ID: NY682AA-AB4 and serial No.: CNX00304C2. Today, I had a problem while giving a configuration with windows 7 Ultimate. A blue screen appeared and the error code was: 0x0000007B. There is a link below which shows the exact screenshot I encountered during the installation. I need a solution as soon as POSSIBLE because my PC died and I can't spend a single day without her. Thanks in advance

  link: http://komku.blogspot.com/2010_02_27_archive.html

  Enter the BIOS by typing /holding F10 key to power on. Check if the hard disk controller is set to AHCI or IDE mode. AHCI mode should work, but if it's the current setting, change IDE. If it is set for RAID on AHCI change.

• Satellite A300 PSAGCA - blue screen using Windows 7

  First by Satellite A300 - PSAGCA-0C301N did not come on the European Internet site when I update the drivers... there PSAGCE...

  I am running on the assumption that A = Australia & E = Europe.
  Can someone clarify this for me.

  The computer worked fine with Vista but since put Win 7 Ultimate here he sometimes gets the blue screen.
  It was a clean place do not install an upgrade

  He can go for a week without a problem, and then I'll have 5 blue screens in one day.
  All the drivers came to the site of the European

  I have 4 GB of RAM
  No devices are connected
  WiFi is always enabled
  Usually connected to the power supply

  If anyone can help to direct me to a solution I would be eternally grateful

  See you soon

  Sammy

  > I am running on the assumption that A = Australia & E = Europe.
  > Can anyone clarify this for me.

  You are right that the last digit or the letter designates the region. Then E means Europe and Australian way.

  It s an Australian series for Toshiba laptop and, therefore, you need to download the drivers from Toshiba Australian page

  The BSOD may be a result of not fully compatible drivers

• tried to install a new copy of Windows XP Home. Everything is OK until the final phase, when the "blue-screen" appeared during the installation of the drivers.

  Installation of xp and blue screen of death

  Hello

  I recently formatted the partition boot and recovery of a laptop Medion2230, then merged the two partitions in a single NTFS partition.  Don't ask why, it's a long story.

  Then, tried to install a new copy of Windows XP Home.  Everything is OK until the final phase, when the "Blue Screen of death" appeared during the installation of the drivers. Restarted and installing XP as normal to repeat the first onboard staged and went to the "blue screen" at the same point as before.

  Using some diagnostic software, I reformatted the drive again, loaded XP set up and I had the same problem.

  Someone knows what to do?

  Thank you allionii123

  Now solved and pc with Windows XP home.

  Discovered a trick online, who said that at the beginning of XP installation, press F5, and this leads to a screen option - select 'standard pc' and continue with the installation of XP.

  (Again), formatted hard drive ran XP installation and followed above point.

  Worked the first time.

  Thank you very much for your advice.

  I think you can pressing F5 or F7...

  How to impose a layer of HAL during an upgrade or an installation of Windows XP

  Impose a HAL

  To prevent Windows XP to automatically determine the system HAL during the upgrade or installation of Windows XP, you can manually force in a system HAL. To impose an Abstraction Layer HAL during a upgrade or installation of Windows XP, follow these steps:

  1. During the phase in text mode of Setup, when you receive the message at the bottom of the screen, press F5:
     Press F6 if you need to install a third-party RAID or SCSI driver.

     Note If you press F7, the Standard PC HAL loads and the ACPI enforcement is bypassed.

  I would not need this except in the systems of many older and low end... :-(  After all, in the same article, for Standard PC they say: "the CPU can be a 386, 486, Pentium, Pentium II, or Pentium III '...

  Thanks for letting us know what you were doing.  Do you have all the necessary drivers after loading Windows XP?  I would not recommend using the default drivers for any hardware - always see what the manufacturer offers on their web page for each component of your system - card motherboard chipset, audio, video, network devices, etc.

• Satellite A300-1MX - blue screen after installation

  Hello
  I have a problem with the Installation of Windows XP. I set Compatibility Mode and everything.
  But at the end of the Installation comes the blue screen and windows stopped.
  "An important topic for the operating system stopped unexpectedly.

  I loaded the Toshiba SATA drivers, but they don t work.

  I put t know what to do, please help me.

  And please forgive me my bad English

  Grettings Infi38

  Hello!

  You need to install SATA drivers before you install Windows and if you have compatible SATA mode you t need SATA drivers but you have lost performance a bit.

  So I want to reinstall Windows in AHCI mode, you need to download the Toshiba Storage Manager (http://eu.computers.toshiba-europe.com).
  Copy the driver on an external floppy drive and press F6 after starting the laptop to CD or create your own installation with nLite (http://www.nliteos.com/) disc.

  Good bye

• Blue screen appears during playback of movies

  Hi, whenever I play a movie with Windows Media Player, the blue screen upwards and I have to restart my system. Is it a hardware problem or software? and what do I do? I will be appreciated if someone could help me with this problem. Thank you.

  Hi, whenever I play a movie with Windows Media Player, the blue screen upwards and I have to restart my system. Is it a hardware problem or software? and what do I do? I will be appreciated if someone could help me with this problem. Thank you.

  ================================
  You may need to update your video driver. John Inzer - MS - MVP - Digital Media Experience - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

• Equium A100-549: blue screen error during installation of the recovery CD

  Hey,.

  I recently bought a Toshiba laptop computer, everything worked perfectly until my laptop was attacked. I've got rid of the virus and went to reformat due to a lot of problems that occur. The main one being a mistake has cursed and 'Blah blah' program must be closed. As I continued to get loads of errors.

  http://aumha.org/win5/kbestop.htm
  The types.

  Now then reformatting disk Toshiba said just put the disk in the drive and turn off. I did very well. The said toshiba drive press F12 on startup and then click on run the CD. The CD starts and gets half way thro reformatting.

  Suddenly, I get a blue error screen. I thought oh well ill reboot and continue. This is where the problem started. Because I was half way thro removal/reinstallation of windows I was missing some files. I'll reinstall or try to use the Toshiba CD, I get a blue error screen.

  0 X 00000050: PAGE_FAULT_IN_NONPAGED_AREA
  (Click to consult the Online Win XP Resource Kit article, or see the Windows 2000 Professional, p. 1548 Resource Kit).
  The requested data were not in memory. An address of invalid system memory was referenced. Defective memory (including main memory, L2 RAM, RAM video cache memory) or incompatible software (including remote control and antivirus software) might cause this stop message, as may other hardware issues (for example, incorrect SCSI termination or imperfect PCI card).

  Any ideas what I can do? I don't want to return the Toshiba laptop to fix However im thinking this is the only way out.

  Please if repplying try to keep technical language to a minnium. Thank you, Dan.

  Hello

  It s very strange because the installation since the Toshiba Recovery CD should work properly and without any blue screen message.
  Usually, if the BSOD appears if there is a serious software problem or something wrong with the hardware.
  I don t think that the software on the CD of restoration could be corrupted.

  Have you tried to install the OS from the original CD of Microsoft Windows? It would be very interesting to know if the blue screen also.

  However, I think that your laptop is new and the warranty is valid. In my opinion, you should ask the after-sales Service of Toshiba partner to help him because guys could start the diagnostic test and can find the fault.

• Blue screen: 0x7e during installation of windows xp

  original title: blue screen of death during the installation of windows xp

  I just bought a motherboard ASUS p5g41t-mlx with a Pentium E5400 2.7 GHz dual core and a hard drive when booting with the windows xp cd in, it goes through the initial configuration and is preparing to restart the computer when I get a blue screen (this is before we get to make a partition)

  It's basically my blue screen message

  problem detected windows stops to prevent damage of the model
  Check for sufficient disk space. If a driver is identified in the stop message, disable it or check updates,
  try changing video cards

  control the bios upgrade. Disable the bios memory options such as implementing caching or shading. Start in
  safe mode to remove or disable components

  STOP: OXOOOOOO7E (0xc0000005, 0xf748e0bf, oxf78da208, 0xf78d9f08)
  PCI.sys - address f748e0bf base at f7487000, DateStamp 3b7d855c

  "superbuddha" wrote in message News: * e-mail address is removed from the privacy * .com...

  I just bought a motherboard ASUS p5g41t-mlx with a Pentium E5400 2.7 GHz dual core and a hard drive when booting with the windows xp cd in, it goes through the initial configuration and is preparing to restart the computer when I get a blue screen (this is before we get to make a partition)

  It's basically my blue screen message

  problem detected windows stops to prevent damage of the model
  Check for sufficient disk space. If a driver is identified in the stop message, disable it or check updates,
  try changing video cards

  control the bios upgrade. Disable the bios memory options such as implementing caching or shading. Start in
  safe mode to remove or disable components

  STOP: OXOOOOOO7E (0xc0000005, 0xf748e0bf, oxf78da208, 0xf78d9f08)
  PCI.sys - address f748e0bf base at f7487000, DateStamp 3b7d855c

  Have you installed the drivers SATA asks to press F6 to install drivers from floppy drive?  Assuming you have this type of "new HDD" with your new motherboard.  (small cable from motherboard to the drive instead of wide ribbon cable.)
   
  You may need to go into the bios of the computer to IDE mode to install the operating system.  Once installed, you can install the SATA drivers and then move into the bios SATA mode for the HARD disk controller.

• Satellite T110-121 - blue screen after the installation of recovery

  Hello everyone! My name is Melanie and I want to apologize for my English: I m french! I have big problems on my laptop, I will explain:

  I had to install windows yesteday and I used the partition recovery, all worked but the last seetings, my computer fixed: blue screen. I have it reboot and I can log in on windows, now Toshiba software run at the end of the installation: install wireless and bluetouth BUT this software always get it fixed my computer or my screen is frozen, or screen of blus.

  Then, I removed it from the startep of the software list and tried to install the drivers I found on the Toshiba site but for the wireless, I run the software add anything, and for the bluetooth it says error 2753: setupdiu.exe is not marked for installation.

  So I m really disappointed, could you have some tips to help me please? I thought reinstall windows, but I can't reach the recovery: whose touch is?

  I m looking forward getting help.

  My best,

  Mel.

  Hey,.

  I think that something goes wrong when installing recovery and thus you get a blue screen and can t install the WLAN software. The best option would be to run the recovery process.

  But why you can't reach t recovery more? I mean you can use HARD drive recovery as often as you like and you can start if you enter Windows Advanced Boot menu (press F8 before Windows starts) and choose fix my computer. Select Toshiba HDD recovery, then follow the instructions on the screen. Windows will be reinstalled with all drivers and tools.

  Check this box!

• While to my desktop screen; the error on blue screen appeared... STOP: Ox0000000c5 (Ox00000002, Ox00000001, Ox00000004, Ox805515A1)

  Original title: in my desktop screen. the BSOD appeared...

  Hello everyone,

  While to my desktop screen (don't remember if I was doing anything however), the BSOD appears, indicating the system stopped to avoid any damage occurs.

  The following was then shown (exactly as you see):

  STOP: Ox0000000c5 (Ox00000002, Ox00000001, Ox00000004, Ox805515A1)

  Then a memory dump has been launched.

  The only way to get rid of the blue screen was to unplug the computer from the power source, then turn it back on.  After reboot, "error reporting box" appears asking if I wanted to report this error to Microsoft I did), then closed the box.  Almost immediately after, the computer I connected to the Internet to a site that says "Microsoft error report" in the upper left corner of the screen.

  Then, there was some additional information about the page displayed on some system functions in my computer does not.  I was directed to click on a link to the so-called "Roxio...?  & then asked to download, "Pxengine 4_18_16A.exe.  (Provided by Sonic Solutions, version 1.13.37.0, created on 20/07/2009).

  This is now a 5th time a blue screen appeared during 5 days.  This time, the only difference is in the codes and being redirected to the page described above to download something I've never heard of and have no idea of what it is supposed to do.

  I would appreciate any information that someone has just what it is.  I'm simply puzzled.

  Thank you very much in advance!

  Hello

  1. don't you make changes on the computer before this problem?

  2 do you have software Roxio installed on the computer? If so, then Uninstall the software and check.

  You can also check if the problem persists in the clean boot state.

• Satellite A100-192: blue screen during the installation of Adobe Premiere

  Hi, I need some help ASP...
  I bought a satellite A100-192 intel duo 2500 T with 100 GB hard drive and 1024 MB 533 memorry also has a vga ATI 1600 hyoer 512 MB memory,
  Try to install the first pro, but I got a bluescreen scrable.
  Can this program somehow in this laptop? any help is welcome...
  Thank you...

  Hi Theodor,

  I suggest that you try to reinstall your copy of Adobe Premiere, and if you still get the blue screen when trying to take note of the error message, since this will give you some clues as to the nature of the problem.

  If the blue screen appears too fast and forces the phone to reboot then just right click on the 'My computer' icon and select 'Properties', then click on the "Advanced" tab and in the "Startup & recovery" section click the "Settings" button In the next under the title of "System failure" screen make sure that the option restart automatically is not checked.

  Kind regards

• A satellite - blue screens appear

  Can Hi anyone help?

  Signature of the problem:
  Problem event name: BlueScreen
  OS version: 6.1.7600.2.0.0.768.3
  Locale ID: 2057

  More information about the problem:
  BCCode: 50
  BCP1: FFFFF880060F5C5C
  BCP2: 0000000000000001
  BCP3: FFFFF880079A0165
  BCP4: 0000000000000000
  OS version: 6_1_7600
  Service Pack: 0_0
  Product: 768_1

  Files helping to describe the problem:
  C:\Windows\Minidump\033110-22464-01.dmp

  THX

  Hey,.

  Unfortunately, I can say nothing because a lot of information is missing:

  -Exact cell model
  -(Pre-installed Toshiba?) exact Windows version
  -When is this blue screen appear?

• Satellite P100-347: blue screen at startup - unable to boot volume

  Recently, I left my 2 younger brothers playing NFS Carbon on my satellite P100-347, pre-installed with media center edition 2005, and now it fails to start.

  During the process of possibly starting a blue screen appears for about a second and then it shutsdown (I managed to make the words "unable to boot volume" on the basis of the blue screen).

  I tried to boot with a XP media center DVD but it gives me only a possibility of reinstalling the operating system with a cost of losing all my important data. Normally I would have picked up the system, but I don't want to lose my data.

  Can I do other than take it to a technician?

  Hello

  Well, for the most part the BSOD appears due to hardware problem or serious software.
  In your case, the software problem is possible

  Unfortunately, I think that the new installation of the OS is the best way to get the laptop works properly.
  Now, you want to know how to record data and the files well, I think that you should remove the laptop HARD drive and must try to connect the 2.5 HDD via external USB controller to another computer. Then you can save the files to the other HARD disk

  I think, now, you know that regular backups are important and necessary!

• Satellite Pro A100 - blue screen keeps coming back

  I have a Satellite Pro A100 (psaase) and a blue screen appears some time it says image kernel memory and the only way out is to restart the laptop.
  How can I fix? Can someone tell me what's wrong with it and how to fix it?

  Thank you

  There are hundreds of causes BSOD. What is the BSOD STOP code?

  0x000000?

• Satellite Pro A60: Blue screen - ATI2DVAG display driver. DLL in endless loop

  Hello
  Laptop is a Toshiba Satellite Pro A60 with ATI Mobility Radeon 7000 IGP video card, running Windows XP Professional and SP 2.
  During the start in most cases systems hang up with blue screen.

  I installed the latest drivers from http://uk.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=UK (Version dated 6.14.10.6430 Date 09/03/2004) but the problem continues. After second - last third - it reboot now works.
  The blue screen says (translated from German):
  "Component that probably caused the problem: ati2dvag.dll; the device driver is in an infinite loop; Subsequently the unit does not work, or the device driver is not program the equipment in the right way. STOP 0X000000EA. A dump was created.

  Please HELP - THANKS in advance!
  Best regards
  Frank

  Hello

  I studied a bit on the Toshiba site and found this interesting paper Toshiba on the error message Satellite A60 and blue screen on startup.
  http://support.toshiba-tro.de/KB0/TSB5300X7000MR01.htm

  This document describes how to upgrade the BIOS. The update of the BIOS should help solve this problem. Take a peek inside.
  Please post if you have solved the problem