Re: Satellite L40-139 - 10 error code in the Device Manager on the wireless network card
I have a toshiba satellite L40-139 and I just instaled windows 7 64 bit on it. Since that time my atheros wireless device will not work. I tried updating the driver and windows but nothing.
In the device manager says code 10 DEVICE can NOT START.
If you read here:
The Code 10 error code is generated when the Device Manager has not enough information or error that spread upwards by device drivers is not recognized by Device Manager.
Then, go to the page of the driver and update the driver. If you do not have to win 7, try the vista driver.
I just bought a Satellite L40 - 18Z. I tried to connect to the internet wireless, but I get the following message: "this computer doesn't have a card installed and configured wireless network."
When I bought it I was told that it was active wireless.
Can anyone help?
Have you checked if the hardware switch wireless on the front of the laptop is on?
You have yellow exclamation points?
The wireless adapter is recognized?
Maybe you should also update the driver and/or BIOS.
http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers
Once, I turn my adapter wireless for my laptop 'ON' and it starts to connect to my router 3com officeconnect wireless.
I found that my router restarts automatically.
This happens each and every time I turn on my laptop with the wireless adapter ON.
I use the Satellite A100-785 PPPoE ISP with WPA/AES encryption enabled on the new MS Vista platform.
All drivers updated to the latest versions, and the wireless signal is Excellent.
Any suggestions that could be the reason or any recommendation to begin to investigate the matter?
Everything will be highly appreciated. Thank you
Once again; Your WLan router restarts (reboots) when you turn on the WLan on the A100 Satellite Map. Am I wrong?
Well, it's strange, but to be honest I n t see a problem with the laptop but with the router. I would recommend controlled again the unique WLan router configuration.
I'm looking to change the card Wifi on my C660 11 H since a Realtek 8188CE for a Realtek RTL8187B, for reasons that cannot be discussed on this forum. I was just wondering if the new card will be compatible, if I understand his also a Bluetooth card? I know that in the past, this is a case of grooving of the card and connecting the antennas.
Finally, can anyone provide me the model number of the integrated Realtek WAN adapter? In system information, he simply says Wan Adapter PCI-E FE?
Thanks for your help / Ryan
To be honest, it would be interesting to know why you want to change the WLAN card. You are not satisfied, or what are the reasons for this?
In the forum, there are some discussions on the WLAN on Satellite C660 questions but this could be solved with latest Realtek driver and turning off energy saving as you can in large number of discussions:
first - sorry for my English. I have toshiba P20 S203 (I know - old hardware).
I read a few descriptions on this computer and I know that the model probably have wifi. I see on the left side of my laptop, but don't see it Win Xp Pro Sp2.
How to turn on and connect to my lan wirreless?
again sorry for my English...
As mentioned the laptop has no installed wireless network card, but you can improve with one compatible.
The minPCI card has two cables; Brown and white.
Usually the white cable be connected to the hand and Brown to the
This morning my Satellite Pro A40 (Celeron 2.6) fell 40 cm. He fell right on the wireless network card that has been inserted. This card is still alive and so is the rest of the laptop, but the PCMCIA location is little damaged. I can insert PC cards almost completely, just the last piece (when the pins are) wrong.
I removed the cover near the CPU, and there, I could see the inside PCMCIA slot; I could see the main part and the last part where the pins are. That little part as is pushed upward, as you can see in the pictures.
I think I'd be able to fix myself this PCMCIA slot, but I can't remove it. I removed all the screws on the rear plate, but he is still blocked.
The PCMCIA location; on the left, you will see the part with the pins, which is pushed upward. It's also what I see when I look at the pins in the PCMCIA slot. as they are pushed down, but I don't think they are folded.
Wireless network card; It is a little damaged but it still works.
Does anyone have an idea how I can remove the back plate, or another way to remove the PCMCIA slot and fix it?
Well, I can give t well you not answer how you can just remove the PCMCIA slot.
There are a lot of screws and to my knowledge, it is necessary to remove all covers and screws that are placed at the bottom of the unit and inside under the keyboard.
Please check this specific device. Perhaps you have overlooked a few screws.
But if it is impossible to remove the PCMCIA slot of the unit, I recommend to ask the service partner for a detailed instruction.
Can I put my card Intel pro 2200BG on Satellite M65-S9092 wireless network so that it is no longer compatible with Windows 7? The Intel Pro 2200BG is no longer supported by Intel as it was abandoned and so they have not issued a new driver so that IPv6 works.
So I would update my card if possible.
Thanks in adavnce
I think that it shouldn't be a problem to upgrade the WLan card.
As far as I know its a card wireless network of miiPCI and you would need to also use a WLan card which would support the miniPCI interface.
The wireless network card supports two pins for the WLan antenna cable.
Usually, you must connect a white cable to the HAND and a black to the auxiliary voltage
All that s
I got a 1nj c660 and I have a wireless connection to a Fritzbox 7170.
Now, this morning, everything was fine and I connected wonderfully, but now I can't connect no settings have been changed I just stop and start as usual. I used configfree and it shows the network but if I try to connect it says unable to connect to the network. I have Win7 home basic OS.
I uninstalled the wireless network card and reinstalled, updated the drivers but nothing works, I still get the same error.
Can someone help will appreciate it greatly!
Are you able to connect to open WLan?
I mean you can try to disable security options in your Fritzbox and might test whether you are able to connect without the WEP, WPA or other safety standards.
Of course, you should only done for testing purposes
If this box works, then it means that the security of your router settings were not consistent with the settings of the Wlan card.
People of the night...
Just got a family run Vista premium, Equium L40-156, everything is going well except a little problem with the display adapter (Mobile Intel 965).
Tried the drivers that I had with the installer
Tried the drivers from the toshiba download page
Tried the drivers on the Microsoft Update site
Tried the drivers from the website of intel
All have the same problem, in Device Manager, it shows with an error (the pretty yellow triangle with the "!") with an error code 12 (the device cannot find enough free resources) even after a system resart.
Switching view hidden devices displays a 2nd same device, but works correctly, but the two disappear if I try to delete either.
Display settings do not display a connected device, DXDIAG had no idea either.
Latest version of the BIOS installed, all other devices are very good and can not see an IO overlap anywhere
Any suggestions, greatly appriciated
I have studied a little bit and looked on the Microsoft page for some answers and found out what exactly means the error code 12.
+ Error code 12 +.
+ This device cannot find enough free resources that it can use. If you want to use this device, you will need to disable one of the other devices on this system. (Code 12) +.
+ Two devices are assigned the same i/o ports, the same interrupt, or the same Direct memory access channel (whether through BIOS, the operating system, or a combination of both). This error message may also appear if the BIOS did not allocate enough resources to the device (for example, if a (USB) universal serial bus controller is not an interruption of the BIOS because of a corrupt MPS (Multiprocessor) system table). +
Well, what to say; usually this error message should not appear with the original Toshiba preinstalled operating system.
I put t know if you have changed something or add an additional device, but it would be very interesting to know if the same error message appears after the reinstallation of the OS.
You can use the Toshiba Recovery CD/DVD of restoration!
All the drivers, the tools are already preinstalled on the recovery CD so the entire procedure will not take very long. about 10 min.
Check this box and report if the same error is displayed on the laptop with the factory settings!
My laptop is Toshiba Satellite L40 - 139 PSL40E model, operating system Windows XP SP3, 1 024 DDR2 RAM (667 MHz) (512 + 512).
I want to increase the RAM memory using 2048 DDR2 RAM (1024 + 1024).
Laptop manual can not find if support * _dual-channel memory_ *, which requires a dual-channel-capable motherboard. Theoretically, this technology double data rate of the memory.
Someone has the manual for this laptop motheboard, or may indicate the site for download?
Apologies for my bad English.
Satellite L40-139 can be upgraded to 2 GB of RAM. You can buy two modules with 1 GB of capacity with the specifications of DDR2 at 667 MHz.
If you use two modules, they run in dual channel mode.
The manual of the motherboard or repair for Toshiba laptops cannot be downloaded. They are only available if ASP.
Hello please, be gentle, lol.
I have a Satellite A30, no manuals, disks etc. of second hand.
I had to buy a wireless card and installed it myself (error?).
The card is an Intel P/N: PA3362U 1MPC.
My is... have issue I installed it properly (see below), and can someone point me in the right direction for the correct driver?
(Correct?) installation... .clipped perfectly in the slot in the compartment in the base of the laptop. Two sons rolled? one longer than the other?
I plugged them as follows... more long wire to THE & shorter wire by HAND (on map)? Does this sound correct?
How could I not if it works?
The LED does not illuminate when the wifi switch is on?
Is it normal when the driver not installed? FN + F8 has no effect? Again the ths is normal without driver installed?
Thank you in advance, I'm completely stuck here... Matt
The PA3362U 1MPC seems to be a network wireless Intel PRO/Wireless 2200BG MiniPCI Type 3b card. I think it is s ok and should be compatible.
The WLan driver should be found here:
Take the Intel PRO/Wireless 2200/2915 driver.
> I plugged these as follows... more long wire to THE & shorter wire by HAND (on map)? Does this sound correct?
I put t know which wire is short or long, but the two sons are different in color.
Should the white cable goes to the hand and Brown to the auxiliary voltage
See also this thread:
> How could I not if it works?
Well, you will not be able to connect to the Wlan ;)
> Is - this normal when the driver is not installed? FN + F8 has no effect? Again the ths is normal without driver installed?
You should check if the other FN keys work correctly. If other n t FN keys work then Fn + F8 does not work too
PS: you can activate the WLan also in Device Manager-> properties-> tab advanced Wlan card
I'm new here, but I want to know how can I activate the wireless network device. On my Toshiba Satellite A100-529 keyboard is a Fn key that must be pressed with the F8 key to turn on the wireless network device. I did, but it does not work.
What can I do to turn on my wireless device?
You are right. The FN + F8 key combination should be used to switch to the WLan card.
But look, man. Have you checked if your laptop supports wireless network card?
I think it does not support the minPCI wireless network card and the card does not exist!
That's why the WLan card cannot be activated :) you know ;)
Hello. I have a Toshiba Satellite M645-S4070.
Lately, I have no problem connecting to networks wireless in my office. Until this morning when I start my laptop, I can't connect to the internet more. I already use a recovery disk to check if I can solve the problem but nothing is. When it connects to the LAN it runs.
The wireless network adapter is listed correctly in the Device Manager? It is maybe just disabled, and you can enable/disable using FN + F9 key combination.
You should write more details not connection might mean everything, so first of all, that you should check if the wireless network adapter is recognized and activated correctly.
I have a Toshiba Satellite A30-104 with an inprocomm ipn2220 built in wireless card. The problem I'm having is that when I get a network says its not available and asks me to turn it on.
The driver is installed for the card, the switch for the wireless is set on you and I pressed FN & F8 and yet led remains off and nothing happens.
I watched autour and seen that some people cover the terminals 11 and 13 and it works but not too sure.
I also should this problem with a new card or is there a way to fix this?
Any help much appreciated.
I guess that you upgraded the wireless lan card later, didn t you? I know that 11 + 13 pins hint and it worked, but after awhile the card did not and the connection quality was so poor that I bought a card atheros on ebay and this card works really well. So I suggest that you are looking for a card atheros on ebay and to install such card in your system since the cards are known to work properly in the toshiba machines.
My configuration: Tecra 9100 with P4M and Atheros 5005 G MiniPCI card
I wanted to update my wireless NETWORK card, but after turning the power on, error 105 - unsupported network device
I have the original is the broadcom wifi + bluetooth combo card and I intend to use a card Intel with 802.11ac ability and also has bluetooth onboard. Its also 2 x 2 if original antenna snap right in
I'm on the latest firmware F15
Is there a way I can install this other NETWORK card?
Help is appreciated!
You can use these wireless cards.
Regulations of the FCC sorry.
Maybe you are looking for
I have a Toshiba USB 16 GB I have used successfully for a few weeks now. Today, I tried to enter in the section 'Secure' and I clicked on LOCKV240. EXE as usual and I presented with this message:http://img.photobucket.com/albums/V504/Ewen/USB.jpg hel
System: HP Pavilion b323w 20 I have recently purchsed this computer and by the fact of hate me windows 8, I installed windows 7. Now I have a problem with my USB controller and SM Bus controller drivers. One of the resources I used: http://h30434.www
I have a desktop Pavilion d5200t with an operating system upgraded to Windows 7 that must be reformatted. I want to delete all data and start over. When I put the Windows 7 CD in the drive and go through install, I click the link Options of readers
It looks like a software bug, because I noticed on my Xperia Z3 double kitakat and lollipop and previously on my Z1: When you're in any application, and you press the button quickly and repeatedly back soft, it stays on you some of the latest open ap
I have a Segate hard drive that had crashed. When I now try to connect to my computer, I can't find on 'Computer' or ' Diskpart > list disk. I find on disk management, but it cannot be initialized. His name is disk 1, as you can see. I can't even cha