Re: Satellite P200-1EE - displays an error message in the windows Boot Manager

Similar Questions

• My phone displays an error message on the startup file and it mentions the installation media, how can I solve this problem?

  Separated from this thread.

  My phone displays an error message on the startup file and it mentions the installation media, how can I solve this problem?

  Hello

  See if that helps you.

  Do a Safe Mode system restore to before the problem started.

  http://bertk.MVPs.org/html/restoresysv.html

  How to access Safe Mode

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  If it doesn't, try a startup repair and / or a system restore using a DVD of Vista from Microsoft

  Manufacturers recovery disks normally do not have Service Options; they are normally a relocation to the factory only settings option.

  Here is the guide to repair Options using a Vista DVD from Microsoft.

  If a friend or a work acquantance of yours has one, you can borrow and use it for repairs.

  http://www.bleepingcomputer.com/tutorials/repair-Windows-with-Windows-Startup-Repair/

  Table of contents

  1. Overview of Windows Vista repair options
  2. How to perform an automatic repair of Windows Vista using Startup Repair
  3. Advanced Tools Overview
  4. Conclusion

  If you do not or can not borrow a Microsoft DVD there is a download of a file ISO of Vista Startup Repair available that you can put on a Bootable floppy to make the above startup repair and that the method is recommended by a large number of posters in these Forums.

  Unfortunately, you have to buy it.

  Here is a link to it:

  http://NeoSmart.net/blog/2011/Windows-Recovery-discs-updated-reinstated/

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  There are several methods to reinstall Vista.

  This can help you (download files and make your own DVDs):

  http://www.heidoc.NET/Joomla/technology-science/Microsoft/57-Windows-Vista-direct-download-links

  And here are instructions on how to burn ISO disk images:

  http://www.SnapFiles.com/get/isorecorder.html

  The download links and information on how to make the ISO file, and then create the Setup DVD above are at this link:

  "How to download a Vista ISO and create a Setup DVD or USB"

  http://www.Vistax64.com/tutorials/301852-Vista-ISO-download-create-installation-DVD-USB.html

  "How to create a USB of Vista Installation key '

  http://www.Vistax64.com/tutorials/181538-USB-bootable-Vista-installation-Flash-thumb-drive.html

  ___________________________________

  You can contact your computer manufacturer and ask them to send you a set of recovery disks.

  They should do this for a small fee.

  To reinstall Vista using their recovery disk/s, you start from the 1st recovery disk they provide and follow the manufacturer's instructions to reinstall:

  You need to change the Boot order to make the DVD/CD drive 1st in the boot order:

  How to change the Boot order in BIOS:

  http://pcsupport.about.com/od/fixtheproblem/SS/bootorderchange.htm

  "How to replace Microsoft software or hardware, order service packs and replace product manuals.

  http://support.Microsoft.com/kb/326246

  ___________________________________

  And if you have never received a recovery disk when you bought your computer, there should be a recovery on the drive Partition hard reinstall Windows how much you bought your computer.

  The recovery process can be started by pressing a particular combination of the key or keys at startup. (Power on / start)

  Maybe it's F10, F11, Alt + F10, etc., depending on the manufacturer.

  Them or us ask the right sequence of key.

  ___________________________________

  Some manufacturers have more available Vista recovery disks.

  If this happens, you may need to try this instead:

  You can also borrow and use a Microsoft Vista DVD, which contains the files for the different editions of Vista (Home Basic, Home Premium, Business and Ultimate) must be installed. The product key on your computer / Laptop box determines what Edition is installed.

  Other manufacturers recovery DVDs are should not be used for this purpose.

  And you need to know the version of 'bit' for Vista, as 32-bit and 64-bit editions come on different DVDs

  Here's how to do a clean install of Vista using a DVD of Vista from Microsoft:

  "How to do a clean install and configure with a full Version of Vista '

  http://www.Vistax64.com/tutorials/117366-clean-install-full-version-Vista.html

  And once the operating system is installed, go to your computer manufacturer's website and get the latest drivers for your particular model or laptop computer.

  And phone Activation may be necessary when you use the above installation method.

  "How to activate Vista normally and by Activation of the phone '

  http://www.Vistax64.com/tutorials/84488-activate-Vista-phone.html

  See you soon.

• How can I display an error message on the listening port close popup without closing the popup.

  Hi Experts,

  JDeveloper 12.1.3.0.0

  How can I display an error message on the listening port close popup without closing the popup.

  Thank you

  Roy

  As its name suggests, close listener of popup is called when popup is closed so you can not do this.

  If you want to display the popup message, use your own buttons instead of the ok/cancel default buttons and close the popup programmatically.

  Dario

• Error: "no physical memory is available to the location required for the windows boot manager." The system cannot continue. "

  I have a stable system that works with a processor E6300, card mother evga 680i, graphics card 8800gts and 8gbs of RAM running on ulitmate windows 7 (32 bits - I decided to re - install with 64-bit to use the extra 4 GB of RAM, after I deal with the question below).

  I recently tried to add an adapter of Intel RS2WC080 SAS/SATA controller in a PCI express slots on the card mother 680i. I know that the card works (such as "it works very well in another motherboard), but for some reason when I put it in the 680i mobo I get the following message appears when I try to start windows. (i.e. the raid controller has no windows on the disks. I always use original hard drive always connected on the same Sata port on the motherboard)

  "No physical memory is available to the location required for the windows boot manager." The system cannot continue. "

  I tried to turn off virtually everything I could in the bios of the motherboard as an experience (including the things I needed). I also disabled the Intel RS2WC080 card bios.

  I'm puzzled. So what I want to know is simply a hardware compatibility problem, or is there some kind of workaround I can run in windows 7. For example, is there maybe some sort of way for her to start using a different memory location than its currently using? (Or is it something error message related to the memory of the bios that can only be overcome with software?)

  Thanks for any help.

  I tried to disable everything in the bios... including the things I needed. No luck

  Thank you very much for the reply Chris but I don't have abandoned bascially. Right now I guess the card and the 680i have some kind of incompatibility and I will just get a different mobo.

• Satellite P200 - 1EE HD DVDs - cannot play beyond the language selection

  Hi all

  I recently bought a new Toshiba Satellite P200-1EE.
  However its HD-DVD player would not play a movie HD DVD (Transformers) at all!

  When I insert the disk it shows the first screen - language selection Menu
  When I choose English or anything else out there it just crashes and beyond would play.

  I had the same problem with another disc too.

  All the world has experienced the same problem and managed to resolve it?

  I went through some of the other solutions given here inculding update to the latest drivers etc, but nothing seems not to help.

  Thank you very much - Arvind

  Hello

  You should visit the page of the Toshiba driver and need to update the firmware of CD/DVD players and HD Toshiba DVD player software.

  This aid comes of course!

• Error messages in the Log Agent Manager

  We get below the error message at the start of the SGF in the log agent Manager

  Sounds to me like the adapter on the fms is not executed in hardware.

  When you go to the Administration > adapters (as agents) do you see an fglam adapter in an active state?

  If it is not active, you can try to turn it on?

  

  Golan

• A pdf file exported from InDesign, but displays various error messages when the same file is downloaded on the same laptop from the company's Web site

  Hello

  I'm having a problem with a pdf file created for my business. It exports without problems and displays correctly on my computer, but once it is transferred to the Web site and you download from here, pages randomly displayed not correctly, images and pieces of text go missing and different "internal error" messages pop up, such as:
  

  "An internal error has occurred."

  "There is an error on this page. Acrobat may not display the page correctly. Please contact the person who created the pdf document to correct the problem.

  "Failed to retrieve the embedded police"LICYDR + GaramondMT". Some characters may not display or print correctly.
  "Insufficient for an image.

  And when I close the pdf file it asks if I want to save even if I did not bring any changes to the document. It seems that everyone has problems with pages and receive different error messages. It is exported using the smallest file size preset in InDesign. Any idea what could be the cause? Any help would be greatly appreciated!
  

  
  

  Thank you

  Sarah
  

  One thing to check is if BINARY is used in the FTP client. If a client FTP ASCII is used, it may corrupt PDF files.

  Here's another thing to check yourself for you. Find the size in bytes of your original PDF. Now, look at the size of the uploaded file in bytes. Are they the same? If this is not the case, ask your colleague the size in bytes of the PDF file on the server. Is this the same as the original, or bad file?

• Satellite P200-1EE Possible to recover data on the HARD drive by placing it in an envelope?

  P200-1EE does not start after 2 weeks off is the case during a fan installation. Is it possible to remove the hard drive, put it in an enclosure and retrieve the data it contains on another PC? Or can anyone recommend how to recover data from the comfort of my own home?

  Thanks for your help

  I would say that your installation of fan caused this problem in the first place. I would check your installation for loose connectors, cards not seated properly, no fan or heatsinks screws tight etc..

  Everything you did everything by installing the new fan plugged the laptop. The hard disk, in my opinion, is perfectly fine. There is nothing wrong with it.

  Put the suspect hard drive in an enclosed and try to access the data on another PC. You will encounter problems with administrator access to certain folders so you will need to find a way to crack in these areas.

  If you had problems in the first place you probably should have this return to the place of purchase for them to watch.

  I hope that for your sake you have not turned into a frisbee.

  Good luck.

• KKKKK displays an error message with the graphics card during the installation

  My laptop is a DV6 6121tx with QB367PA #ACJ product number.

  During the installation of kkkkk, it displays an error saying not able to recognize the graphics card in the system.

  Please suggest an update secure for the soul if they are available.

  HP support assistant details of my graphics driver:

  Radeon (TM) HD 6770 M

  8.882.2.3000 (30/09/2011)

  Hi champakBhumia,

  Welcome to the HP forum!

  Here is a link to the HP Pavilion dv6-6121tx Entertainment Notebook PC specifications and HP Pavilion dv6 Notebook PC Maintenance and Service of Guide , which will provide a recommended list of replacements.

  I hope this helps.

• When loading of the audio books of the library, I get an error message from the Window Media Player.

  The message indicates that Windows Media Player has encountered a problem when downloading the file. I can down load MP3's but am unable to down load WMA format books. I could upload it before Windows 7.

  Hi Stanley,

  Thanks for joining Microsoft Community.

  Description of the question, we understand that you get error while download in format WMA books from Windows Media Player.

   
  If you could answer a few questions that would help us resolve this problem:
  1. have you recently installed third party codecs?
  2. don't you make changes to the computer before the show?

  We would like to tell you that this problem can occur because the DRM store on the computer is not valid or is corrupted.

   
  Here are a few methods that you can follow to solve the problem:
   
  Method 1:
  Run the troubleshooter in the Windows Media Player settings.

  http://Windows.Microsoft.com/en-us/Windows7/open-the-Windows-Media-Player-settings-Troubleshooter

   

  Method 2:

  Please visit the following link:
  http://drmlicense.one.Microsoft.com/crlupdate/en/crlupdate.html

   

  I hope this helps. If you have any other queries/issues related to Windows, write us and we will be happy to help you further.

   

   

   

   

   

   

   

   

   

• Hello, I get the beginning of the muse of adobe are the error message that the adobe application manager is damaged or not installed now, I downloaded 2 times and installed the problem persists, however, can me someone here with a rat page

  Hello

  I get the beginning of the muse of adobe, the error that the application manager adobe is damaged or not installed

  Now, I downloaded 2 times and installed the problem remains, however

  can someone here with rat page

  Kindly try to remove Adobe Application Manager to help cleaning tool and remove CC help | Uninstall the creative desktop application Cloud can download and install Adobe Creative Cloud apps.

• Receive an error message that the HP Connection Manager service not installed

  Original title: Application of program compatibility... I get a box that says. Service not installed HP connection manager... so it says incompatible... How can I fix it?

  This box appears whenever I start my computer...

  Hello

  1. what version of Windows you are using (Windows XP, Vista, 7)?

  2 did you change on your computer before the show?

  Follow the steps mentioned below:

  Method 1:

  Step 1: Run in SafeMode networking

  Safe mode, start Windows in a limited State, where only the essential is started. If a problem does reappear when you start in safe mode, you can eliminate the default settings and basic device drivers and services as causes possible

  Start your computer in safe mode with networking

  http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode

  Step 2: Perform the clean boot

  A clean boot helps eliminate software conflicts. The article below describes how to solve problems in Windows 7 by performing a clean boot. This article also describes how to start the Windows Installer service and how to reset the computer so that it starts as usual. To configure your computer to clean boot see the following link.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: When you are finished troubleshooting, follow step 7 in the article to start on normal startup.

  If the problem persists, follow the next method

  Method 2:

  Let us try to reinstall the HP connection manager and check with the question.

  HP Connection Manager service

  http://h30434.www3.HP.com/T5/notebook-operating-systems-and/HP-Connection-Manager-service/TD-p/891309

  It could be useful!

• Satellite P200-1EE PSPB6E: problem of battery and Webcam

  Hiya People,

  New on the Toshiba Forums here and stuck on a problem I have with this laptop.
  I have a Satellite P200-1EE model number: PSPB6E 0GM028EN. The election House of Uni a few days ago my refuses to laptop to turn on the laptop on and happening only when I put a Power cable in.

  I took out the battery cleaned with a can of Air and put it again and it worked but the next time I did nothing happened.
  Strange thing is that, once it is running, and I take the power wire, it works fine.

  2nd problem is the software integrated Webcam won't work for me. Sometimes, and when I restarted the laptop it works fine again.
  I tried to reinstall the driver but it gives warning that the newest is already installed on my laptop.
  Am I right in thinking that its due to the new version?

  Any help or Suggestions are appreciated and thanks in advance

  Seamus

  > Laptop on and lights up only when I put a power cable. I took out the battery cleaned with a can of Air and put it again and it worked but the next time I did nothing happened. Strange thing is that, once it is running, and I take the power wire, it works fine.

  It is maybe something wrong with the battery of laptops of s?
  How old is your laptop? Guarantee is valid?

  As far as I know, the guarantee covers the battery for one year. Then maybe you should ask and ASP in your country for a control? Maybe the battery doesn't work as it should.

  > 2nd problem is the software integrated Webcam won't work for me. Sometimes, and when I restarted the laptop it works fine again. I tried to reinstall the driver but it gives warning that the newest is already installed on my laptop. Am I right in thinking that its due to the new version?

  I n t have a solution to deliver you but I assume that it s associated with the software/driver of webcam.
  You should visit the European driver Toshiba page from time to time and need to check if an update is available.

  Good luck

• Screen saver has an error message preventing the opening

  Screensaver displays an error message prevents the opening. Help

  Hello Robert,.

  I would like to know some information about the problem so that we can help you better.

  What is the full error message when you say, "screen saver has an error message preventing the opening"?

  Thank you for details on the issue.

  I also know that the inconvenience you are experiencing due to problem of screen saver. I will definitely help you.

  This problem can occur because of incorrect or corrupt files of Windows power settings.

  I would suggest trying the following methods and check if it helps.

  Method 1:
  Create a new power plan and check the issue.
  Refer to this article:
  Change, create, or delete a power plan (scheme)
  http://Windows.Microsoft.com/en-us/Windows/change-create-delete-power-plan-scheme#1TC=Windows-7

  If this does not help, use method 2.

  Method 2:
  Run checker (SFC) of file system and see if it helps.
  Reference:
  Use the System File Checker tool to repair missing or corrupted system files
  https://support.Microsoft.com/en-us/KB/929833

  System File Checker is a Windows utility that allows users to find corruptions in Windows system files and restore the damaged files.

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• Error message indicates that Windows Imaging Component (WIC) is missing or damaged.

  Trying to open Turbo Tax 2011, it gives me an error message on the Windows Imaging Component is missing or damaged.   I equipped of Windows Vista-64 bit on my HP Pavilion dv 5 laptop.  They give a place to download the component, but it still does not work.

  Any suggestions?  It seems to be the only program that does not work.  Everything else works well.

  Hello

  1. where did you download the component?

  2. it worked before?

  3. don't you make recent changes?

  I suggest you to uninstall and reinstall the software and check if it helps:

  http://Windows.Microsoft.com/en-us/Windows-Vista/uninstall-or-change-a-program

  It will be useful.