Re: Screen corruption after upgrading memory

Similar Questions

• Satellite L100 113 starts slowly after upgrade memory

  Hello

  Toshiba Satellite L100 113 PSLA3E-02401JRU starts slowly after upgrade memory with Kingston KTT533D2-512 (512 MB) of memory.
  When I press the 'power' button, it flashes, starts the fans and HARD drive several times. Then it shows BIOS start messages by memory full 768 MB and starts Windows XP without a problem.
  This behavior is noticed only after "shut down."
  It does not happen with "restart".
  What can I do to eliminate this long "attempts" to start my laptop computer?

  Thank you
  Novomir Kovalenko

  Hello

  This problem appears before upgrade memory?
  Have you used exactly the same memory modules?
  If this isn't the case, then perhaps there are a few compatibility issues.

  Usually, after the insertion of the modules you must enter the BIOS and then save the settings. Please it and eventually the laptop will start without any problems.

• Firefox 4 beta too slow / crashing after upgrade memory?

  Hello

  my beta firefox started crashing my whole system yesterday and only noticeable change I did was upgrade memory of 3 to 4 GB of RAM...

  I tested my system widely and it works very well until firefox is started, after that, the system started crashing and takes forever to be reactive. I uninstalled and reinstalled firefox, tried running without addons, I tried to close all the tabs and all Eske I remembered... still no luck.

  I am desperate because I really wanted to keep this beta on my computer, and cuz is a new facility, I can not install firefox 3.6 on side by side, I only have an option 'upgrade' on the installation wizard...

  What can I do to fix this?

  Thanks in advance!

  The steps to troubleshoot and diagnose problems of Firefox would say you always try in questions to troubleshoot Firefox in Safe Mode of course some additional software may conflict, it is even more likely if you are using a beta version of firefox and probably the beta or alpha some of the addons or plugins.

• Cannot get any sound on my speakers after upgrading memory

  just updated my computer by adding more memory but I can't get any sound on my speakers

  Hi RawleHouston,

  Thanks for posting your question in the Microsoft Community.

  I understand that you can not get any sound of your speaker after upgrading your memory. Correct me if I'm wrong.

  I imagine the inconvenience that you are experiencing. I will try to help you in the matter of fixing.

  To help you suggest several steps to solve the problem, I would appreciate if you could answer the following questions:

  1. What is the brand and model of the computer?

  2. you receive an error code or message?

  Please follow the methods and mark the question below:

  Method 1:

  Step 1:

  Run the Microsoft Fix It from the link below.

  Diagnose and automatically fix the audio problems and audio playback:

  http://support.Microsoft.com/mats/AudioPlayback/

  Step 2:

  Follow the steps in the link below.

  No sound in Windows:

  http://Windows.Microsoft.com/en-us/Windows/no-sound-help#no-sound=Windows-Vista&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Method 2:

  Follow the steps in the link below.

  Tips for solving common audio problems:

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-sound-problems

  I hope that the information above helps you, and if you encounter any problems on Windows, please do not hesitate to post your request here on Microsoft Community, we will be more than happy to help you.

• Satellite L50 - A - 1 5 PSKK6E does not start after upgrading memory

  Upgrade memory L50 - A - 1 5 pskk6e

  I have a memory ddr3 4 gb 1rx8 pc3 - 12800 S-11-12-b2 hynix and I tried to add another memory
  memory DDR3 4 gb 1rx8 hynix pc3 - 12800 S-11-11-b2, but it does not boot up the laptop.

  I tried to mount only the new but it won't start.

  Some ideas?

  I think that it s you already know that this Satellite L50 - has - 1 5 would support max 16 GB of RAM (2 x 8 GB)

  But why, box for computer laptop doesn t is very simple: the new modules are not compatible.

  I found modules recommended by Toshiba.
  These are:
  8GB DDR3L - 1600 PA5104U-1M8G
  4 GB DDR3L - 1600 PA5104U-1M4G

  Both are made of Kingston and the specifications are:

  Memory speed: 1600 Mhz PC3-12800
  Capacity: 8 GB (1x8GB module)
  Pins: 204 SODIMM
  Type of RAM: DDR3 SODIMM
  Verifying the integrity of data: non ECC
  Specifications:
  Latency (CL) CASES: 11
  Voltage: 1.35v

• Satellite C660 - black screen after upgrade memory

  Can Hi anyone please help

  try to upgrade the ram on my C660 account currently 3GB - talk to Toshiba and they told me the type to get and said im running 64-bit windows, I could go up to 8 GB - then bought the following

  DDR3 1066 MHz sodimm - x 2@4GB---de MyMemory.com (£64)

  When I mounted it and turned on the screen is all black.
  Anyone has any ideas please im in the middle of my assignments aaaaaahhhhhhhh!

  And any help would be really appreciated

  John

  Hello

  Looks like not compatible or faulty module.
  You can start the laptop properly using the old modules?
  If Yes, then the new memory should be replaced by another.

  I recommend modules Kingston I think they make good quality

• Satellite M30X-122 does not start after upgrading memory

  Hello

  I want to upgrade the RAM in my Satellite M30X 122. Correctly my NB contains 2x256MB.
  I bought a GB 1 333 MHz. Cl2.5 module PC2700 (corresponds to the former, but more grand ;-)))
  Now I build in the module, but after the build-in system is dead.
  It doesn't show anything on the screen (after pressing the button one)).

  Does Anyboby have some tips?

  Thank you very much
  Peter

  Hello

  Toshiba has recommended the use of these memory modules:
  PC2700 256 MB (PA3311U - 1 M 25)
  PC2700 512 MB (PA3312U - 1 M 51)
  1024MO PC2700 (PA3313U-1M1G)

  Well, the size of 1024MB should be compatible. In this case, it s not a module size.
  Have you tried to get into the BIOS? BIOS recognizes the memory module?
  Maybe the module is broken?

  In my opinion, you should check if the module memory works on a different unit. If this module works correctly on another unit if your M30X doesn t support this module of memory and you need one another.

• What is the text on the lock below screen date, after upgrade to IOS 10?

  Hello

  I have iphone, and after I upgraded to IOS 10, from dated on the lock screen (muh.5 1438 AH).

  What is - this and how can I remove it?

  Hello

  Try a reboot press and hold the power button / stop and menu button hold both down until you see

  Apple logo.

  It may take 30 seconds.

  See you soon

  Brian

• Performance degrades in Probook s 4540 after upgrade memory

  Hello. I installed recently in my memory modules two Kingston Probook4540 (2x8gb ddr3 1600 CL10 240 pins). Since I did this, Windows 8 is much longer to start and performance dropped considerably. But, if I put only one of the two modules, or the original 4 GB module, Windows runs at normal speed.

  I think it's a BIOS problem, as I see this error even on laptops the other brand, for example here
  http://superuser.com/questions/379970/laptop-is-incredibly-slow-after-RAM-upgrade
  
  I have the latest BIOS version available (F31 26-SEP-2012).
  
  Thank you.

  In case anyone is still interested in this topic:

  It is a solution that worked for me.

  It is not an official solution or supported.

  I used the laptop intensively in the described configuration and had no problems that I can relate to the configuration of the memory.

  Deduct from a 256 MB RAM memory available for OS could eliminate the problem for some processors.

  The solution runs on:
  -HP 4540S

  -i5 - 2450M

  -AMD/Intel switchable graphics card

  -16 GB OF RAM

  -Bios F.42

  It might work for other processors.

  Under Windows, you should deduct 256 MB of RAM, using EasyBCD or a similar tool.

  Instructions for EasyBCD:

  Under Advanced settings/developer set 256 under "MiB deducted from physical memory", save the settings and reboot.

  In Linux, the "mem = 17G" value in the boot of the kernel settings (actually deducted 256 MB).

  Edit:

  On Windows 7 and later versions, you can also use the following instead of EasyBCD:

  bcdedit/set {current} removememory 256

  (Run the command at the prompt with administrator privileges and restart).

• HP 15-p206tx: Recovery is corrupt after upgrading windows 8.1 for windows 10?

  Recovery does not work after update to windows 10, so we should remove, or there is a way to make it work as he was over 22 GB of memory.

  I think also that it is not no matter what condition of recovery in windows 10 we can get new facility without worrying about product key because it is digitally embeded in our system.

  Hello

  Thanks for posting in the HP Support forum.

  After completing an upgrade from 8.1 to 10 and if the activation was successful, then you have been activated using a new method called digital right. To win 10 you no longer need a key/COA sticker, etc. Next time you try activation on the same computer, it will get automatic activated due to the new method as long as it's the same PC (not a different).

  In regard to the recovery partition - you can delete it if you think it doesn't, and if you do not plan to return to Windows 8.1

  If you need any kind of recovery Win 10, you can simply download the ISO 10 Windows from the Microsoft web site and use it to
  - either burn it to a DVD

  - or write on a USB

  You can then use this DVD/USB drive as a recovery to perform the steps of recovery or reinstallation complete Windows 10.

  > > https://www.microsoft.com/en-us/software-download/windows10ISO

• R50E does not start after upgrading memory

  I tried to upgrade this laptop from the factory of 512 MB to 1.5 GB. I got a Kingston 1 GB DDR - 333 SO-DIMM, but after I installed it, the laptop does not turn. Only the power led is lit.

  I don't know why this happened, because all tests indicate that it should work.

  1. the new stick is ok. I tested it in another laptop and it worked. I also cleaned the contacts with isopropyl alcohol.

  2. the memory locations are ok. The old memory works in each slot.

  3. I tried to install the new one stick in a slot and it did not work.

  4. This update is officially supported by record of IBM and BIOS is up to date (v2.1, December 2006).

  Unless I'm missing something there is a confusing question. Unfortunately, I don't have an another 1 GB DIMM to test with.

  yehuda1 wrote:

  TBut I don't think it's a matter of density. something fundamentally wrong with this system. I just discovered that I can not upgrade the memory somehow, even not with a stick of 256 MB. The system starts only with the current key.

  OK... This is not good, but I have to tell you that...

  I guess it's time to throw the boy part of retirement and move to a new machine...

  Good luck.

• Why my screen blinking after upgrade to 7?

  monitor constantly blinks after start upward. I have the model of g70 smart touch and after the upgrade of system 7, the screen flashes constantly.

  Windows Update has nothing to do with the upgrade of Windows.

  Maybe you need an update of the driver for your video card or your system can't handle Aero? Post here for assistance: http://social.answers.microsoft.com/Forums/en-US/w7hardware/threads ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• W500 PCI-Express does not work after upgrade memory 4gig

  Laptop is a W500 with WinXP SP3. I have the external ViDock PCI Express video card. Absolutely, it works like a champ. I recently received an upgrade of memory 4gig for the W500. After the upgrade of the default value would be 2gig RAM for the new 4gig, the laptop does NOT start with the inserted PCI Express card. I remove the card PCI Express ViDock and it starts very well and of course, works very well. Same behavior either stand alone or in the docking station. I tried going back to the 2 Gig of RAM and the new ViDock works perfectly. Google is pretty quiet on this issue... This could be a problem with the ViDock? the W500? Windows XP? The memory? Doesn't seem wise for me a memory 'simple' update would disable a component. Thank you,-Ryan

  May be the same as the question TOLUD?
  http://forums.Lenovo.com/T5/T400-T500-and-newer-T-series/request-to-fix-TOLUD-in-newer-BIOS-files/TD...

• HP-431. Can't change my monitor resolution and screen brightness after upgrade to windows pro 8.1

  I can't change the resolution of my screen and the brightness of the screen after I upgraded the Windows of windows 7 ultimate for windows pro 8.1 build 9600

  I have already installed the graphics card, but I can't change my resolution of more than 1024 x 768

  My laptop is HP 431 with processor intel core i3 - 2310 m 2.10 GHz, AMD graphics 7450 M DDR3 1 GB HD (I don't know why, but I have already installed graphics AMD HD series 7400 M because my laptop is not compatible with the other AMD graphics), 64-bit OS

  I think that's the problem
  http://prntscr.com/3mf9l5
  What do you think guys?

  Please, help me

  Thank you

  I'm sorry that this driver has not worked.

  The pilot I posted should be only for laptops with the series 7 Intel chipsets.

  I guess W8.1 is not in charge of your model.

  You can see if this W8 driver works, but I think that nothing is going to work for this model.

  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3DswItem%253Dob_110852_1&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

• A6745f crashes on startup after upgrade memory.

  Try to improve this machine with 16 GB of memory. A row of 2 x 4 GB sticks work great, but when I try to put in the last 8 gb, it freezes just after the display of the memory on the opening screen. It records all the 16 GB is there, said then "press F10 for bios' and hard locks. I have to pull the plug.

  I swapped the sticks around without problem. The MB watch news that he supports this quantity of memory in a 64-bit environment.

  BIOS Rev - Phoenix 5.13

  MB - MSI - MS-7548

  Running Windows 7 Professional 64 bit.

  Kilroy14 wrote: I guess that the MB does not have the 16 GB literature although not? I guess this is no longer supported. If anyone has experience with this, please let me know. Thank you all!

  Hello Kilroy14, I checked the specifications of your system, which can be found here , and it does not show the system supports up to 16 GB of memory system.

  I also found the Crucial or Kingston memory did not 4 GB memeory modules listed for your system.

  Another provider of memory has indicated that some Kingston memory would be only recognized as a total of 8 GB even though there were 4 x 4 GB modules installed.

  It is not, as you suggest, this model can not supported 4 GB modules when installed in all memory slots.