Read the latest version of the driver NOR-RIO by program

Hello.

Is there a way to read what NOR-RIO's version of on my RIO programmatically? I know I can get this information through MAX, but I want to get this information at run time.

Terje-

If you do not want to develop a
application with replication tools, please see using FTP with
Windows Explorer.  If you copy off of full HD which only goes
be bigger than your app about 15 MB... This will include all the
software.  It is also an easy way to make backups of their
configuration and software.  I think that will be the best way
This round.  Let me know how well are you and if you have a
questions.  I'll make sure that it will be evaluated for a future
Release.

Kind regards

John

Tags: NI Hardware

Similar Questions

  • I can't install the driver OR RIO in my cRIO use MAX 5.5

    I can connect it assign a static IP address. Whenever I try to install the software in the FPGA target, appears the following error message:

    "Timed out while communicating with the remote server. Ensure that the system is online.

    What can I do?

    I have LabVIEW 2013 installed in WINDOWS 8

    Hi Vitrion,

    As seen in the Service request, this problem was resolved when you demoted to LabView 2012 and reinstalling Max5.5, so we can properly install the Driver NOR-Rio and sees the device to the Max apparently, it was a compatibility issue in versions...

    Just a recommendation for a few cases like this. Please check the compatibility chart before installing an update of LabView in order to have the right version of Driver OR-Rio.

    http://digital.NI.com/public.nsf/allkb/577CC9A7DCFC73DF8625738400116CC3

    Kind regards

  • What version of the driver NOR-488. should 2 I use

    I need to update my driver OR-488. 2 in order to work with an operating system of Windows 7 (64-bit).  I know by the cards that it says version 2.7.3 will work with both 32-bit and 64-bit Windows 7, but the latest version of hardware driver States that works with "Windows 7".  The latest version works with 32 and 64 bit, or is it naturally 64-bit only?

    This will work for both.

  • Uninstall the Driver nor visa 3.0.1 to install 4.2

    Hi all

    I need to install the Driver or visa 4.2, but should I uninstall visa or 3.0.1 firstly to let the 4.2 to be effective.

    But I have some problems to uninstall the Driver nor visa 3.0.1.

    I wait your help for how to uninstall it.

    Thank you

    Thank you for your attention.

    I'm new on this. I just found how I can uninstall it from Add/Remove control panel part.

    Thanks for your time

    Problem is solved.

  • 12.1.1 new install: AC-00402: cannot read the driver file: addbtmpl.drv

    Hello

    Im making a new 12.1.1 install the new test server and unziped downloaded media on the disc (not not using DVD). I ran not adautostg.pl because I felt is was not necessary because the downloaded media.

    I did the pre-installation steps according to metalink 761566.1
    He did uncompress drives then I get the following error and I can't file: addbtmpl.drv anywhere. This is step 2 of 5-> database configuration 92% (RW50004). I can't proceed immediately.

    /U01/app/Oracle/DB/tech_st/11.1.0/appsutil/log/VIS_ < servername > 09171403.log

    Logfile located at /u01/app/oracle/db/tech_st/11.1.0/appsutil/log/VIS__ < servername > ApplyDatabase_09180926.log


    | 0% completed AC-00402: cannot read the driver file: /u01/app/oracle/db/tech_st/11.1.0/appsutil/template/addbtmpl.drv

    Cannot run configuration database using RapidClone

    RW-50010: error:-script returned an error: 1
    RW-50004: Error Code when you run the external process. Check the log file for more details.
    Install the driver of database running for instance SCREWS

    Thank you

    Im making a new 12.1.1 install the new test server and unziped downloaded media on the disc (not not using DVD). I ran not adautostg.pl because I felt is was not necessary because the downloaded media.

    You don't need to run the intermediate script if you have downloaded the site Web e-Delivery - in the electronic help files fast delivery to install in Oracle E-Business Suite Release 12 [406138.1 ID]

    I did the pre-installation steps according to metalink 761566.1
    He did uncompress drives then I get the following error and I can't file: addbtmpl.drv anywhere. It is step 2 of 5--> (RW50004) database configuration 92%. I can't proceed immediately.

    0% completed AC-00402: cannot read the driver file: /u01/app/oracle/db/tech_st/11.1.0/appsutil/template/addbtmpl.drv

    It seems that the file is missing.

    Please run md5sum according to (checksums MD5 for R12.1.1 Quick Install Media [802195.1 ID]) to check the integrity of the domain stage directory before running the quick installation.

    Thank you
    Hussein

  • I can't read the .avi files with any program on my system.

    I can't read the .avi files with any program on my system. Have several programs that all of them played before September 2010, like the classic, windows media center windows media player media player, Director of windows, windows, 5.3, video programs video ulead dvd creating toshiba. Nothing works, frustrating not being able to download videos from two different cameras and burn them on DVD. I get an error of almost all the programs, saying that it was unable to load the required component, but I can't determine what this component. I tried to reinstall the codecs again non-joy.

    The free utility GSpot to identify the codec that created
    a .avi file... maybe it will help solve the problem:

    Download GSpot
    http://www.free-codecs.com/download/GSpot.htm
    (left-click the text: "Download GSpot")
    (on the next screen...
    left click: 'Download [GSpot 2.70]')

    You don't have to install it... just unzip the file and
    GSpot.exe left click to launch.

    GSpot Super quick start
    http://www.headbands.com/GSpot/v26x/Quick_Start.html

    Evaluation of video files and Codecs with GSpot
    http://www.windowsmoviemakers.NET/PapaJohn/68/GSpot.aspx

    Good luck.

  • Why using the driver NOR-DAQmx ANSI C functions in a thread causes a deadlock?

    Firstly, apologies if this is bad advice, but it seemed the closest fit.

    I use MSVC 2008 Express with the library in ANSI C NI DAQmx for some analog output with a box USB-6009. I create a thread to handle the signal generation is based on fixed time. My main thread running the user interface. I found that I get intermittent blockages in release, so that libraries mode NOR are responsible (in the second thread) and I use MSVCRT features (on the main thread). My test code is attached as "deadlock2.cpp".

    I used WinDbg to try to find the cause of the deadlock. Traces of the battery of my two sons are attached as t1_stack.txt and t2_stack.txt.

    It seems that the MSVCRT localtime() function uses a lock when it is called for the first time and then went to lock the Windows DLL loader lock. At the same time libraries NOR (or less libraries mxs) are responsible for locking the charger DLL is being held. The mxsutils library uses getcwd() which seems to try to block something the MSVCRT and therefore my two sons are now deadlocked.

    I can probably work around this by calling the localtime() and the NOR-DAQmx functions before I spawn my second thread so that the DLLs are already loaded in the process. However, I have no guarantee of this to continue working if something changes in the future, and if there are any locks going on finally having the DllMain() calls for a thread hanging may still cause a deadlock. If my results are correct, is it likely that NEITHER would fix the dll for not trying to make something complex in their DllMain()?

    According to NI Measurement and Automation Explorer, I'm under DAQmx libraries v9.3.5f2. I download the latest version now to try, but it will take time.

    Hi dmcminn,

    Thank you for the comprehensive and detailed bug report. I was able to reproduce the problem with NOR-DAQmx 9.6 using the code you posted. I reported it to the R & D team suitable as CAR #366538.

    I agree with your analysis of the problem. Getcwd() so the first call to __tzset() acquired _ENV_LOCK, which Microsoft has documented as the "lock for environment variables. __tzset() also called GetTimeZoneInformation(), which can load additional libraries, that you have demonstrated.

    Here are a couple more possible solutions, but they are not great:

    • Link to the static version of the CRT (/ MT instead of /MD). This would bind a separate copy of the lock of the CRT table in your program, and DAQmx would continue to use the lock to MSVCR90.dll table. They use more of the same _ENV_LOCK.
    • Build using a different version of Microsoft Visual C++ (for example 2005 or 2010). MSVCR80.dll MSVCR90.dll and MSVCR100.dll own separate copies of the lock of the CRT table.

    Whatever it is, it does not eliminate the fact that mxsutils called the CRT while now the loader lock, and this function CRT acquires another lock.

    Furthermore, the forum Multifunction DAQ is a better place to ask questions DAQmx.

    Brad

  • RT system timeout when updating the driver NOR-DAQmx 8.9.5 to 9.0.2

    I installed LabVIEW 2009 on my host (Window XP) which has now NOR-DAQmx 9.0.2 installed.  My remote RT chassis has NEITHER-DAQmx 8.9.5 installed.   I need to have versions of NOR-DAQmx match on my host computer and remote systems.  I tried to install the driver OR DAQmx 9.0.2 my host by using the LabVIEW Real-time Software Wizard.  The Installer tries to restart the remote chassis on the installation mode but expires and returns the error Code 56.  How can I get my versions to match?

    Problem caused by the wrong installation order.  Necessary to install 9.0 RT first on target.  NOR-DAQmx has been updated at the same time.

  • FireWire Camera disappeared to MAX when you select the driver NOR-IMAQdx

    Hi, as the title suggests, I'm having a problem getting my camera firewire (a PixeLINK PL-A742) appears in MAX so I can use it in my application. First of all, a bit of history.

    It was all works fine on an old computer (Windows XP SP3, LabVIEW 8.6.1, NOR-IMAQdx 3.2).

    We just received two new computers. They have Windows 7 Professional 64 - bit installed on them, then we are stuck using that (I was going to install labview in XP Mode, but there is no support for firewire, which no longer works). After finally getting installed labview (to run the setup.exe from Distributions\LabVIEW-ENG\LabVIEW861\, rather than make the autorun) we cannot get this camera to work. It works very well with the PixeLINK pilot (and Capture OEM program that accompanies it).

    So here is what I tried, and what happens when I do.

    (1) install cost of LabVIEW (including IMAQdx 3.2) and PixeLINK drivers.

    (2) at this stage, the camera works very well in the PixeLINK application

    (3) start MAX. It detects the camera and shows under devices NOR-IMAQdx. When you click on the camera, it informs me that the selected device is not currently associated with legacy OR-IMAQ driver IEEE or the driver OR-IMAQdx. This is perfect, it is supposed to do.

    4) click camera > driver > choose NOR-IMAQdx IIDC camera digital

    (5) he then disappears from MAX (no record OR-peripheral IMAQdx more). If I goto windows Device Manager, it comes under National Instruments IMAQ Interfaces as NOR-IMAQdx IIDC camera, says the pilot did get properly, it just does not appear in MAX more...

    (6) at this point, there is nothing I can do to get it back to the MAX (except in Device Manager to switch the driver on the PixeLINK one, then he pops up and we return to step 3)

    So, any ideas? This could be a problem with firewire interface and not the camera? I use the FireWire on my computer. It presents itself as Texas Instruments 1394 OHCI compatible host controller in Device Manager.

    Here are a few screenshots to help illustrate my problems.

    It is the initial configuration using the PixeLINK driver.

    It's MAX with the PixeLINK driver

    As soon as I click on the NOR-IMAQdx IIDC camera, it disappears

    And here's what it looks like in Device Manager after you have selected the NOR-IMAQdx driver

    Anyone have any ideas? I'm open to anything. At this point, I'm completely at a loss to know what to do.

    Thanks in advance,

    Devin

    Mechanical engineering intern

    University of Victoria

    Well, you can just ignore this message now. I solved my problem. I installed Vision Acquisition software 2009 and it seems to have solved my problem.

  • E4200 forget how to read the drive

    As the subject says after running poorly, but at least running with my 2 to external hard drive attached Buffalo my E4200 is now a failure as a NAS.

    It will not display a speed of USB, but claims to know how big the drive is. He claims there is also no action on the disc, it was reading very well last week.

    A quick test by plugging the drive into a PC shows that it works perfectly.

    He is currently blocked "Detection" on storage - menu disc.

    The SIN of this router performance is catastrophic, given its cost, I was hoping rather a 1.0.02 upgrade would solve things, he seems to have done the worst.

    This is clearly a firmware issue, the behavior cannot be explained by anything else.

    If anyone has a work around for that while Cisco hired wherever they are cheapest in the developers of the world are considering ways to degrade the NAS functionality (I thought 35Mbit on a player capable of > 150 Mbps via USB direct has impressive degradation!) even further it would be most appreciated.

    Why close a maximum, I found the 1.0.01 firmware online and inspired to the router.

    The drive works again and the instability of 2.4 GHz went.

    Disgusting that Cisco Linksys have released new software to fix the wireless, NAS or media problems of server or at least reconstituted 1.0.01.

  • Read the text of an external program

    I'm sure it will be a Windows Library thing, but any help would be great.

    Here's what I need.

    In a software project, I will carry out an FTP (WSFTP) so the device that I connect can download start-up files.

    For now, operators must allow unit to complete its startup process. They know its finished reading the text of WSFTP

    text window. I want to make is that my program enter this text of WSFTP text buffer.

    I'm guessing this will require window and control HWND. I never had much of a Windows programmer.

    Any ideas?

    Looks like a winning approach.

    WayneS1324 wrote:

    Or maybe I could set up a simple FTP server in LV?

  • The problem of the driver NOR DMM 3.0.1 update

    Hi, I'm trying to download the new version 3.0.1 of the DMM in my computer, however, he said "the compressed (zipped) folders error: Windows cannot open the file, the compressed (zipped) folder is invalid.

    did anyone get this problem? I have already download twice, but the problem remains the same.

    current version of DMM: 2.9

    Hello!

    I just tried to download the zip file myself, and I had no problems with it (even if it was in the network of the company, that may have some effect).

    However, a quick search revealed the following Microsoft KB: Zip files downloaded with Internet Explorer are not stored on your computer

    The error you described seems to occur when you use Windows XP and download through Internet Explorer by default Zip program files compressed (zipped).  There seems to be several solutions to this problem, which is the link.

    We also provide a small Downloader application with NOR-DMM 3.0.1 which avoids the problems caused by interrupted data transfers.  You can also try that give it a shot instead of download the zip file raw (you get the same file to be in the end).

    Please let us know if this solves your problem.

    Thank you

    Tobias G.

    National Instruments

  • Cannot read the drive PC computer.

    Original title: Please tell me I'm not crazy and that the problem could be solved... Help, please!

    I am baffled by the fact that my pc can't read a pc, such as a disk drive to sync to my computer with my printer wireless. I was not aware that a computer could not read a disc that is intended for a computer please help!

    Hello

    1. are you having issues with all CD/DVD?

    2 have you made any changes to the system before the show?

    You try to insert the CD in another computer running Windows XP and check to see if the same problem happens.

    Resolution:

    I suggest that you run the fix it or follow the manual for troubleshooting steps described in the link below to fix the problem.

    Your CD or DVD drive is missing or is not recognized by Windows or other programs

    http://support.Microsoft.com/kb/314060

    Note:

    To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

    How to back up and restore the registry in Windows

    http://support.Microsoft.com/kb/322756

  • Try to install the driver, get error "no program associated to open. BIN file"XP

    Trying to download and install a driver and a version update system for my Zoom H4n recorder, I get an error message that says something like "no program associated to open. BIN files. How can I fix this so I can manage my music. Thank you!

    This is how you do it .

  • In Windows 8, I can't read the text entered for several programs

    When I type text, the cursor moving but nothing appears on the screen.

    My installation of Windows 8 did the same thing after each update.

    Right click on the desktop, select Personalize, and then select one of the default themes. This will reset to reset the text to a white police to a black police.

Maybe you are looking for

  • Share the iMac screen and keyboard with Mini?

    If I have a Mac Mini, can he share the screen and the keyboard of my iMac (27-inch, 3.4 GHz with OS X 10.11.6 end 2012)?  Or I need additional hardware on my desk?

  • the cleaning Strip

    I currently have a fitbit and it is impossible to remove the newsprint and the other the band including Clorox marings (as you can tell, I'm desperate); However, I don't want a black band. What bands pick up less and those dirt that stains easily cle

  • MFP (Hi Speed)

    In my page devices and printers, I have an item labeled "USB 2.0 MFP (high speed), which has a! against which means that something is wrong. I used the built in Trouble shooter, and who is unable to solve the problem I have disconnected all external

  • How can I remove an image in Photoshop

    How can I remove an image in PhotoshopI did a test of an iPhone application and he transferred an image in Photoshop.I don't want to make adjustments or send it to Lightroom.I just want to remove permanently.It is a symbol of the garbage on the botto

  • Problems with updating creative cloud to desktop. (error code: 2)

    Problems with updating creative cloud to desktop. (error code: 2)