Readability icmp GLBP IP SLA

Similar Questions

• DF bit value IP sla icmp

  I want to put a mechanism to control the reachbility between two nodes by using the property intellectual ALS, but I find no definition df bit for ip sla icmp packets, y at - it ideas to do?

  Best regards.

  Hello

  int f1/0

  no ip policy map route df

  output

  local policy IP map route df

  Kind regards.

  Alain

  Remember messages useful rate.

• EEM script to alert on failures of the IP SLA

  I have the following IP SLA put in place and would like to do the following. I wish I had a journal entry, if any the below have a failure and then send an email to alert for this failure. Is it possible to do this with the EEM?

  ALS IP 1010

  interval of UDP-Jig 64.xxx.xxx.xxx 3456 num-30 25 packages

  history of 24 hours-of-statistics - kept

  IP SLA annex 1010 duration to always start now

  ALS IP 1011

  TCP-connect 64.xxx.xxx.xxx 2000

  history of 24 hours-of-statistics - kept

  IP SLA annex 1011 duration to always start now

  ALS IP 1012

  64.xxx.xxx.xxx echo ICMP message

  frequency 30

  history of 24 hours-of-statistics - kept

  History 10 distributions-of-statistics-kept

  ALS IP calendar 1012 duration to always start now

  Thank you

  Mike

  Sure.  You can use Enhanced Object Tracking to track each IPSLA collector and EEM to respond to delays.  For example:

  track 1 accessibility of 1010 ip sla

  !

  Event Manager applet track-1010

  event track 1 State

  message from syslog to action 1.0 "Collector IPSLA 1010 timed out."

  "action mail 2.0 of '[email protected] / * /'to'[email protected] / * /" object "Collector IPSLA 1010 is down" body "Collector IPSLA 1010 has exceeded" Server "10.1.1.1" "

• Tap closed/no using ip sla with applet interface EEM

  Hello

  I have to come up with a script of 'close' a particular interface on a router (3945E running IOS 15.0) when a link falls down and also "not closed" after the link back to the top. That's what I have so far.

  track 1 accessibility of sla 10 ip

  delay 10 10

  !

  ALS IP 10

  echo ICMP - 192.168.0.1 - interface source GigabitEthernet 0/1

  frequency 30

  Annex IP SLA 10 life never start-time now

  !

  drop-down link Event Manager applet

  event track 1 State

  action message 1.0 syslog ' response timed out; Link is down.

  command action 1.1 cli 'enable '.

  Action 1.2 "conf t" cli command

  Action 1.3, command cli "g0/0 interface.

  action 1.4 'closed' cli command

  Action 1.5 cli command "end".

  Action 1.6 syslog msg "stop GigabitEthernet 0/1 Interface.

  Link-Up event manager applet

  Event State track 1

  message from syslog to action 1.0 "Ping received; Link's up. "

  command action 1.1 cli 'enable '.

  Action 1.2 "conf t" cli command

  Action 1.3, command cli "g0/0 interface.

  action 1.4 cli command 'no shut '.

  Action 1.5 cli command "end".

  Action 1.6 syslog msg 'Interface GigabitEthernet 0/1 upward.

  I have to go to a remote site and get this working in a maintenance window short but unfortunately I have no way to test it and I don't want to go blind. So if someone could check that the script works with my version of the IOS, it'll be great.

  This will work, but your syslog message seems to indicate that the wrong interface is shutting down.  You must also 'Manager event session cli USER username' If your router uses the AAA command authorization.

• EEM Script works only with IP SLA

  I created script linked to SLA of intellectual property.  If the IP SLA is violated, we want the script to run and stop bgp peers and send syslog messages and can send by e-mail.  I get alert on ALS IP missed, but nothing else happens so screwed up the script in any way. This is the first time using EEM scripting if any help would be great.  Given that we have never used EEM scripting in this place the version that we would use is the default version provided with SRI 4451 in 2015. I do not know if what counts.

  Thank you

  ALS IP 1
  ICMP-echo 8.8.8.8 source-interface GigabitEthernet0/0/1
  threshold 2
  frequency 5
  IP SLA annex 1 point of life to always start-time now
  activate the IP sla response alerts

  track 1 accessibility of als 1 ip

  Event manager E-MAIL ISSUE INTERNET SERVICE PROVIDER environment
  Event Manager environment _email_server 10.1.1.3
  Event Manager environment _email_to [email protected] / * /
  Event Manager environment _email_from [email protected] / * /

  BGP_NEIGHBOR_DOWN event manager applet
  SHUTDWON BGP PEERING description IF IT IS PROVIDER of QUESTION
  event track 1 State
  command action 1.0 cli 'enable '.
  Action 1.1, «config t» cli command
  Action 1.2 cli command 'router bgp 10125 ".
  Action 1.3 cli command "neighbor x.x.x.x stop."
  Action 1.4 cli command "end".
  Action 1.5 syslog-msg 'PROVIDER NETWORK PROBLEM DETECTED, BGP PEERING SHUTDOWN. '
  EMAIL_BGP_PEER_DOWN event manager applet
  Description EMAIL BGP PEER DOWN
  event track 1 State
  action 1.1 mail server "$_email_server" to "$_email_t" of ' $_email_from ' topic ' vendor number: PING FAILED "body"Ping Google's failed. "
  Action 1.2 syslog msg ' EMAIL SENT to $_email_to.
  !

  Then configure:

  Event manager cli username USER session

  Where the USER is a user authorized to execute all CLI commands in your strategies of EEM.  Or add "auth bypass" at the end of each config applet.

• How can I simulate 50% load on a point to point WAN circuit to measure the latency of a pre-determined SLA?

  I just built a remote DMVPN RADIUS with an 300Mbps private point-to-point circuit to the data center.  My manager has promised an SLA of< 20ms="" at="" 50%="" bandwidth="" utilization="" (i="" think="" he="" made="" that="" up?!).=""  i'm="" trying="" to="" sort="" out="" the="" best="" way="" to="" test/document/baseline="" this="" statement="" for="" the="" customer.=""  my="" questions="">

  Can how best I simulate a 50% load on the circuit? -My thoughts would be to set up some sort of maximum bandwidth QoS between 2 hosts and push then a large amount of traffic across the link and then average latency statistics ICMP to ping between the same two hosts.

  Without going into too much detail, the remote site is using ASR1001 (DMVPN spoke) with tunnel interfaces ASR1002 worms (DMVPN hub).  3750 x at the access layer.

  3750 x > mm fiber > asr1001 (speak) > 300Mbps circuit > 3750 x > asr1002 (hub) > l ' infrastructure.

  Thanks in advance!

  On the client side of Iperf use the-b option to specify the available bandwidth. [UDP]

  I hope this helps.

  See here:

  http://OpenManiak.com/Iperf.php

  UDP tests: (-u), bandwidth settings (-b)
  Also see the section "Jperf.

  UDP tests with the argument u will give valuable information on the jitter and packet loss. If you do not specify the argument - u, Iperf uses the TCP protocol.
  To keep a good quality link, the packet loss should not go more than 1%. A high packet loss rates will generate a lot of retransmissions of TCP segment that will have an impact on bandwidth.

  The Jig is basically the variation in latency and doesn't depend on the latency. You can have high response times and a very low jitter. The jitter value is especially important on network links supporting voice over IP (VoIP) as a high jitter can interrupt a call.
  The argument-b allows the allocation if the desired bandwidth.

  Client side:

  10.1.1.1-c #iperf u b 10 m

  ------------------------------------------------------------
  Client that connects to 10.1.1.1, port UDP 5001
  Send datagrams 1470 bytes
  The UDP buffer size: 108 KB (default value)
  ------------------------------------------------------------
  [3] 10.6.2.5 local port 32781 connected with 10.1.1.1 port 5001
  [3] 0, 0 - dry 10.0 11.8 MB 9.89 Mbps
  [3] send datagrams 8409
  [3] the server report:
  [3] 0, 0 - dry 10.0 11.8 MB 9.86 Mbps 2,617 ms 9 / 8409 (0.11%)

  Server-side:

  #iperf s u-i 1

  ------------------------------------------------------------
  Server that is listening on port UDP 5001
  Receipt of datagrams 1470 bytes
  The UDP buffer size: 8.00 KByte (default)
  ------------------------------------------------------------
  [904] 10.1.1.1 local port 5001 connected with 10.6.2.5 port 32781
  [ID] interval transfer band jitter bandwidth Total lost datagrams
  [904] 0,0-1,0 s 1.17 Mbps ms 1,830 9.84 MB 0 / 837 (0%)
  [904] 1.0-2.0 sec 1.18 MB 9.94 Mbps 1,846 ms 5 / 850 (0.59%)
  [904] 2.0-3.0 s 1.19 MB 9.98 Mbps 1,802 ms 2 / 851 (0.24%)
  [904] 3.0-4.0 sec 1.19 MB 10.0 Mbit/s ms 1,830 0 / 850 (0%)
  [904] 4.0-5.0 sec 1.19 MB 9.98 Mbps 1,846 ms 1 / 850 (0.12%)
  [904] 5.0-6.0 sec 1.19 MB 10.0 Mbps 1,806 ms 0 / 851 (0%)
  [904] 6,0-7,0 sec 1.06 MB 8.87 Mbps 1,803 ms 1 / 755 (0.13%)
  [904] 7.0-8.0 sec 1.19 MB 10.0 Mbit/s ms 1,831 0 / 850 (0%)
  [904] 8.0-9.0 sec 1.19 MB 10.0 Mbps 1.841 ms 0 / 850 (0%)
  [904] 9, 0-10, 0 sec 1.19 MB 10.0 ms 1,801 Mbits/sec 0 / 851 (0%)
  [904] 0, 0 - dry 10.0 11.8 MB 9.86 Mbps 2,618 ms 9 / 8409 (0.11%)

• Remote host IP SLA ping by tunnel VPN with NAT

  Hi all

  I did some research here, but don't drop on similar issues. I'm sure that what I want is not possible, but I want to make sure.

  I want to monitor a remote host on the other side a VPN. The local endpoint is my ASA.

  The local INSIDE_LAN traffic is NATted to 10.19.124.1 before entering the VPN tunnel.

  Interesting VPN traffic used ACL card crypto:

  access-list 1 permit line ACL_TUNNELED_TO_REMOTE extended ip host 10.19.124.1 192.168.1.0 255.255.255.0

  NAT rules:

  Global (OUTSIDE) 2 10.19.124.1 mask 255.255.255.255 subnet

  NAT (INSIDE_LAN) 2-list of access ACL_NAT_TO_REMOTE

  NAT ACL

  access-list 1 permit line ACL_NAT_TO_REMOTE extended ip 172.19.126.32 255.255.255.224 192.168.1.0 255.255.255.0

  This configuration works very well for traffic from hosts in 172.19.126.32 255.255.255.224 is 192.168.1.0 255.255.255.0.

  However, I like to use "ip sla" on the SAA itself to monitor a remote host with icmp ping 192.168.1.0. This would imply NATting one IP on the ASA to 10.19.124.1, but I do not see how to do this. None of the interfaces on the SAA are logical, to use as a source for this interface.

  Thanks for ideas and comments.

  Concerning

  You are absolutely right, that unfortunately you won't able to NAT interface ASA IP address. NAT works for traffic passing by the ASA, don't not came from the SAA itself.

• How to convert 'time' readable value?

  When I print just a playlist of iTunes directly on my printer, the time taken by each song fate of easily readable as way for example: 03:27 or 03:08 (minutes and seconds). Choice of the paper version iTunes does not unfortunately for our situation (a dance group need more songs on one page for the program of dances to play each week that would take on one of the pages in the iTunes of a print to the list). I learned how to export the play list in a text file and load to Microsoft Excel (which allows to print more lines per page), but the time taken by each song comes out as just a number (for example, 207 and 188 for the examples only). These values are to be a constant percentage of minutes + seconds digits. It should be possible to convert. But how? It is not among the options provided by Excel when loading a text file.

  I'd hate to convert each hand!

  Thank you.

  P.S. I have a Mac Mini, as indicated below, but the problems that I have described are spend on my Windows 7 PC.

  Rather than address the export, it would be easier to simply copy (from view songs in your iTunes library) and Paste into Excel.

  So if you have this in your library:

  

  .. .you will get this in Excel:

  

  Note that the time of stay in the format mm: SS .

• 5 pages readable documents published on 6 Pages?

  Not all users upgrade os each year.

  5 pages readable documents published on 6 Pages?

  (BTW, I don't understand why it comes to page 6 No Pages 5.7)

  In the trial brief that I did, Yes, 6 Pages can open a Pages 5.6.2. I created a new file in Pages 6 on a Mac & then he opened pages on another Mac 5.6.2. Its opening without the warning and I was able to close the file without getting a new Save dialog box. This indicates that Pages 6 uses the same file structure. I also did a test yesterday and was able to open a file Pages in page 6 4.3.

  Of course, there are a lot of messages in this forum to users having problems with 5 Pages being impossible to open the Pages 5 files created in a different version. Sometimes, he can't even open the files of the same version! Personally, I stick to 4.3 Pages.

  

• How can I recover the modules and their data from a failed HARD drive (the lost BONE areas, but data files are readable)?

  The HARD drive that was my OS (Windows XP Pro SP3) failed and lost quite a few areas which are essential for the operating system running. Other data is still readable. A got another HARD drive and installed Windows XP SP2, Firefox and other programs. I was able to retrieve the bookmarks, security certificates, and other profile information using the information found in bandages.

  None of them addressed how do to recover the modules or their data. Specifically, there are several large, elegant scripts that took months to develop and customize.

  Articles related to migration and other do not work for me because they require the old copy of FF is functional, that is not because the OS on this HARD drive is damaged. Is it possible to recover these data, similar (or not) about how I could get the other profile info?

  Have you copied the entire folder C:\Documents and Settings\username \Application Data\Mozilla\Firefox\ on the old drive?
  If this is not the case, can you?
  If so, make a copy and save this folder just in case.

  If so, you could replace this folder on the new facility by \Profiles\ [with your profiles inside] folder and the profiles.ini file [delete all other files / folders that may also be in the folder "Firefox"] -and then replace with the same folder named from the old failed drive. Note that you will lose what you already have with the new installation / profile!
  Your profile folder contains all your personal data and customizations, including looking for plugins, themes, extensions and their data / customizations - but no plugins.
  But if the user logon name is different on the new facility that the former, any extension that uses an absolute path to the file in its prefs will be problems. Easily rectified, by changing the path to the file in the file prefs, js - keep the brake line formatting intact. The extensions created after the era of Firefox 2.0 or 3.0, due to changes in the 'rules' for creating extensions usually are not a problem, but some real old extensions that need only "minor" since that time can still use absolute paths - even though I have not seen myself since Firefox Firefox 3.6 or 4.0.

  View instead of 'Modules' I mentioned the 4 types of 'Modules' separately - Plugins are seen as 'Add-ons', but they are not installed in the profile [except those mislabelled as a "plugin", when they are installed via an XPI file], but rather in the operating system where Firefox 'find' through the registry.

  Note: Migration articles can tell you do not re - use the prefs.js file, due to an issue that I feel is easily fixed with a little inspection and editing. I think you can manage that my perception is that you have a small shovel in your tool box, if you encounter a problem you are able to do a little digging and fixing problems with the paths to files - once you have been warned.

  Overall, if you go Firefox 35 35 or even Firefox 34 to 35, I don't think you will run in all the problems that you can not handle [that I cross my fingers and "hope" that I'm not on what it is obvious].

  With regard to the recovery of the 'data' for individual extensions - there are many ways that extension developers used to store their data and pref. The original way should save in prefs.js or their own file RDF in the profile folder. While Firefox has been developed more, developers started using their own files in the profile folder. And because Mozilla has started using sqlite database files in Firefox 3.0, Mozilla extended their own use of sqlite, as have extension developers.
  Elegant uses the file stylish.sqlite to store 'styles', but something in the back of my mine tells me that 'the index' maybe not in this file with the data. But then again, I can be confusing myself a question I had with GreaseMonkey awhile back where I copied the gm_scripts folder in a new profile and with already installed GreaseMonkey but with no script. These GM scripts worked, but I could not see them or modify them - they do not appear in the user GM extension interface window in Firefox.

• Export of text Messages on PC readable by form

  Hello

  Sorry if it's a question of relationship, but I have an iPhone 4 and I would like to transfer my text Messages on my PC in a readable (with photos) such as Word, PDF or HTML format. Maybe even have the ability to transfer them to my iPhone (or at least some parts of their)

  Here is a longer version of the question.

  My PC that I had my iPhone 4 sync with iTunes crashed. So currently, I'm not synchronized on iTunes. I have a new PC, but I plan to get the iPhone 7 so I thought I'd go with just the new PC and new iPhone combo. I have a laptop that I play with I can sync to my iPhone 4 with iTunes - if it must be done.

  If I sync the iPhone 4 to iTunes on my laptop, I want to make sure that the phone does not get wiped out and lose everything that is already on it.

  Any ideas?

  Thank you.

  NYA.

  http://www.wired.com/2013/11/Backup-SMS-iPhone/

  If you want more

  SMS backup iPhone to computer

• External hard drive is more readable by Mac.

  Hello

  I have an external hard drive, 2 TB WD My Passport and I have a lot of things out there that I have collected over the past 2 years. When I had OS X Yosemite, I took everything out of it and reformatted it so I could more than just read the documents there and it worked perfectly. Once I upgraded to El Capitan head drive no longer works with my mac and I don't know anyone else with a mac to try to recover the files. When I plug the hard drive, it says "the disk you inserted is not readable by this computer." and then it gives me three options: initialize..., ignore and eject. I don't know what to do, I'd be more than happy to reformat, but I have to delete it before doing this and I really don't want to lose all my documents. Is there a solution to this problem other than to lose all my documents and reformat the hard drive?

  Thank you very much to everybody and all those who take the time to watch and help with this problem!

  Click on ignore and try to repair it with disk utility.

  However, the player may be dead and you will need a type of service or file recovery software to recover the data.

• all of a sudden all of the emails I received before 14:00 today are all the source code for the new ones nsince PAREN then are all readable ideas?

  all of a sudden all of the emails I received before 14:00 today are all code source hyperlink the nine since then are all readable ideas?

  Right-click on the folder, select Properties, and then choose the button repair.

  Long term solution is to not allow your anti virus scan profile of Thunderbird folders.

• improve the readability of the pictures taken on i-phone 6

  People,

  I use an iPhone 6 to take pictures.  My quality is 11.7 GB and my version is 9.3.2 (13F69).  Can I take a photo

  and send it to another mac, but I have problems, showing a readable picture.  I liked to retouching photo, but need help.  I'm a newbie taking pictures.

  Thanks in advance.

  Assuming that you don't take pictures of burst, the picture is actually taken when you lift your finger from the button.  So make sure that you do not move the camera.  See also these:

  Get help with the camera on your iPhone, iPad or iPod touch - Apple Support

  Take and edit photos with your iPhone, iPad and iPod touch - Apple Support

• How encrypted emails can be converted into readable text?

  All my emails in Inbox disappeared from Thunderbird. I opened the subfolder "Inbox" under "Profile" (using WordPerfect to open) and I think that the missing e-mails are there. However, they are coded and I can't make any sense of them. Does anyone know how to convert them into readable text? I use Windows 7.

  Says that the file file type is "file".

  I spent 3 days on this now and I'm tired. I think I'll try using some e-mail recovery software.

  Thank you for your help.