reading power data acquisition

Hello

I m using a box NI USB-6211 to acquire tension. I m using voltage probes with likely to measure values above the limit of +-10V.

The problem is:

-The value that I read in Labview (CSR, continues the samples... just a simple read) is not sensitive to the likely

Hello

Thanks for the help. You are absolutely right!

I m will change the input circuit to include 1Mohm resistance and then pass the value of the voltage to the daq card.

Thanks again

Tags: NI Software

Similar Questions

  • The reading of data acquisition via tcp

    Hello

    I am building an application that controls an acquisition of data via tcp.

    I have a JAVA program that communicate with labview, give a command and data acquisition starts. (So, I read the correct Java data at Labview)

    My problem is if I try to read data acquired by data acquisition (continuous sample 1 k samples), I've read strange values.

    I transform of double values in the string and send it via tcp.

    How can I read it in Java? What type of socket should I use? What is a rate problem?
    I also tried to transform small/big-endian byte order, but it does not work.

    I enclose a sketch of this part of the application.

    Please help me, I try for 2 weeks!
    Thank you all...

    I find the solution in the lavag forum.
    I post here, if it can help someone.

    http://lavag.org/topic/16359-sending-LabVIEW-data-via-TCP/page__pid__99983#entry99983

  • do you need a power supply to the current entry with data acquisition or 9265

    Hello I just receive the NI 9265 Daq for research in my lab. I'm trying to present entry and display it on an oscilloscope. I don't get anything. I did some research on the internet, so my question is do you need a power supply to the current entry with data acquisition or 9265?

    Read the data sheet.  Clearly on the first page is a sentence which reads "the NI 9265 requires 9 V to 36 V external power.

  • Data acquisition reading incorrect when you use a loop

    Hello

    I wrote a simple VI (00, 01, 10, and 11) output to a circuit connected with 4 resistors. Based on what value the ciruit receives, it passes current through a particular resistance. It is again entered in Labview and traced.

    The problem is when I send a particular value (i.e the 00, 01 and 10 and 11) and get that back, it's okay. But when I send and receive the consectively connected via the loop counter, they are incorrect (not synchronized with the number of the loop).

    I made sure that circuit works very well. It has something to do with the loop synnchronization, reset, value compensation, etc. can be.

    Please Guide...

    Change your DAQ assistant that reads to be 1 sample on request.

    Right now it is set for continuous samples.  And 10 samples at 10 Hz.  Then it runs and starts.  The next iteration, you send a new digital out, but the wait for 4 seconds.  When you read again, you get the next 10 samples that are put into the buffer of data acquisition, but now 40 samples have actually entered the DAQ buffer.  In time your DAQ buffer will be finally complete and raise an error.  In the meantime, you will continually read data continues to become more tainted by the iteration.

  • Input module of data acquisition can be read by two or more LabVIEW vi at the same time % 3F

    I use the DAQ palette in LabVIEW to read the virtual channels of the input data acquisition module. I've done several VI who read many entries of three modules of simulations. The problem appears when I run two or more VI´s reading entries from the same virtual module (for example. first.VI module 1 input ai0 and second.VI bed ai0 entry module 1 bed), when this happens the next errors are shown:

    Error-50103

    Platform AND Services: The specified resource is reserved. The operation could not be performed as indicated.

    and

    Error-200022

    Resource requested by this task has already been reserved by another task.

    It's worrying because I want to get the DAQ chassis and some modules, but if this problem is present with physical equipment my application may be unnecessary. This means that entry module only can be read once at the time?

    I m using global variables in each Subvi to share data with main VI, however, I found the solution in a different way... I just changed to single channel and dbl sample playback mode, so I Don t need to clean up the task of reading in my subVI´s, the zeros isn´t problem here, and the six subVI´s work at the same time!

    Thanks for the tips!

  • Read for the acquisition of data entries are overwritten

    Hey there

    I have a Daq reading input in a spreadsheet file

    Data acquisition was told that one is supposed to have some time a loop around it and I cannot get it to run without one, so good

    But my main problem is that it means that it replaces my written file each time that the loop repeats

    He also asked me to choose the file to write in several times

    How would I go about fixing this?

    Thank you

    Yes, you can convert digital to the chain, check the attached VI. I recommend you to go through the basic materials of LabVIEW and also play with example of NEITHER which comes with LabVIEW. Remember not to use the attached example and the acquisition of data, always use separate loops.

  • Reading data series acquired a data acquisition

    Hello

    I have acquired data from a serial port by using an NI USB-5132 on the same computer. I would read these data in order to recover the original string sent. How can I do this please?

    Exactly what do you mean by "observe the signal" and why do you need to do this? If you need to perform some sort of parametrics on the signal (amplitude, rise time, etc.), you can connect the scope and use the product NOR or any USB-RS232 converter ($ 10 - $ 20) inexpensive to get the data.

  • DSA maxing out CPU data acquisition

    I'm developing an application on a PXI-8196 (Windows XP) controller that uses a card PXI - 4472 DSA to read a single microphone and a FFT signal analysis. I need solve the two frequencies of 36kHz (and), so I've planned for sampling 96 kech. / s. I wrote a simple loop of data acquisition, configuring NI44xx DAQ/read screws using read the string unique at this rate, but when I run it, it immediately pegs my CPU 100% usage. So far, I did have problems with missing samples or the system crashes, but I am a little concerned that only data acquisition uses all my CPU time. Y at - it tricks that I can implement to reduce the CPU load?

    I tried to vary the parameter samples per channel - with sizes ranging from 1000 to 48000 samples - buffer but I do not seem likely to reduce the CPU usage. Changing the sampling frequency affects the CPU usage (up to about 40% to 48 ksps / s; ~ 75% 72 ksps / s), though. According to this KB: http://digital.ni.com/public.nsf/allkb/D9DDF9FA02D1C18A86256EBC0016C93D

    "A controller Embedded PXI-8176 can compute all the time of the spectra of FFT power on 8 channels for PXI-4472 clocked at 102.4 ksps / s »

    so I think with my 8196 I should have no problem at all to read only one channel 96 kech. / s.

    Anyone have any suggestions to reduce my CPU Overload? Thank you!

    Here is a link to some good information on how to OR-DAQmx 7.4 and later behaves with respect to the use of the processor: Default CPU use with NOR-DAQmx Version 7.4

  • 2 channels of AI on a data acquisition with the range of different sensitivity

    This vi is based on the 'new project' state machine on the home screen at the start of LV.

    A time loop is parallel to the main loop of the state machine, shown in the picture.

    It works continuously until you press the Exit button.

    The problem seems to be in start this... > read >... stop start > read >... stop along the error line.

    The reason for this clumsy arrangement power is measured voltages are in two lines of different sensitivity.

    The shunt voltage is small and needs-. 2 to the range of V.2. The load voltage is greater and 09:50 V range is good.

    In the initializing state, two separate vi 'create a channel' have been used to specify the range of voltage to the physical channel. The corresponding tasks are sent via via local variables.

    DAQmx errors happen randomly, sometimes the first iteration, sometimes the 50th.

    I tried to disable one or the other start > read > stop for the shunt voltage or load.

    I tried replacing them with the DAQ assistant.

    I tried various DAQmx vi: "wait" and "accomplishment of the tasks by resource cancel selected".

    But error-50103 "specify resource is reserved" keeps popping up.

    Is it possible to create two tasks on the device even when they are not used at the same time?

    The only reason is to measure in two voltage ranges.

    Win 7 Pro 64-bit

    2014 LV database

    Data acquisition equipment: USB-6210

    Thank you.

    This has been discussed many times. Do NOT use separate tasks. You can use different ranges for different channels with a single task. Just wire the task from one channel to another channel to create task.

    You also use local variables when they are certainly not needed.

  • Pavilion TS 17-g099nr: PCI Data Acquisition and processing of the Signal Windows 10 x 64 controller driver

    Hi, it is impossible for the moment to install the driver for PCI Data Acquisition and Signal Processing.

    I downloaded the driver from Intel, and it did not work... I found a version of this site for windows 8.1 unupdated and it does not work.

    A little help?

    Thank you!

    Hello:

    It could be one of two different drivers.

    Try this one first, and then restart the PC.

    This package contains the Intel Chipset Installation utility. This utility allows the operating system to show the correct name for the Intel hardware that is installed in the Microsoft Windows Device Manager. This package is provided for the laptop models running a supported operating system.

    FTP://ftp.HP.com/pub/SoftPaq/sp75501-76000/sp75561.exe

    If this does not work, try this one...

    This package contains the driver which allows Intel platform dynamic and thermal firmware setting. Intel platform dynamic and thermal environment information system temperature and power use for the thermal protection of the system to work properly. This package is provided for the laptop models running a supported operating system.

    FTP://ftp.HP.com/pub/SoftPaq/sp75501-76000/sp75506.exe

  • 15 - ac122tu: PCI of Data Acquisition and the controller driver of laptop HP 15-ac122TU signal processing

    Hi team,

    I just install windows 7 edition integral and peripheral Bluetooth windows 8.1 is not be detectable, when I search for problem that I came across this PCI data acquisition and Signal Processing controller driver is missing and a unknown device driver missing shownup in my result of troubleshooting. Please help me

    Please find the screenshot for your reference

    Thank you

    Hello:

    See if these drivers work...

    CQI PCI controller:

    This package contains the driver which allows Intel platform dynamic and thermal firmware setting. Intel platform dynamic and thermal environment information system temperature and power use for the heat of the system
    protection to work properly. This package is provided for the laptop models running a supported operating system.

    File name: sp71638.exe

    Bluetooth:

    This package contains the installation package driver for Realtek bluetooth in the laptop models running a supported operating system.

    File name: sp71288.exe

    Unknown dev:

    This package provides the HP 3D DriveGuard software (HP ProtectSmart Hard Drive Protection) for the laptop models running a supported operating system. HP 3D DriveGuard software protects the drive hard by parking the heads if cell phone accidentally falls, or is suddenly struck by another object.

    File name: sp71811.exe

  • motion control for vertical actuator and data acquisition

    Hello

    I am a researcher (a branch of civil engineering) geotechnical engineering and I have very little knowledge about the acquisition of control and data motion, so would need a lot of help from the experts OR. I have only knowledge base on these 2 aspects based on my reading of some materials on the Web site of NOR and youtube videos, so I hope that you bare with me . Here are my questions:

    I am trying to build an actuator which will be used to push a probe (a penetrometer with a load cell to measure the resistance of a soil sample), resembling the concept, photography in the attached file. I need to have these criteria for my system:

    (1) actuator, which can push the probe at speeds between 0.01 mm/s - 300 mm/s with precision and move the probe cyclically (upwards and downwards) in the vertical direction
    (2) load expected on the probe into the ground range: 0.02kN - 6 kN.
    (3) necessary to get the load cell load data and the speed of the probe.

    4) able to control the actuator to a PC (speed and posotion) and monitor data from transducers and data log time even the transducers.

    Guess my beginners is that I will need:

    For orders:
    (1) software - LabVIEW and NOR-motion assistant

    (2) controller - NI PCI-7342

    (3) driver/amplifier - analogue servo AKD Drive

    (4) motor - motor brushless servo AKM

    For the acquisition:
    (1) software - based LabVIEW development systems

    (2) amplifiers or other device - no idea what type on the conditioning of signals

    (3) data acquisition device - no idea what type

    Since I'm a beginner, is - that someone might recommend components (hardware and software) for the control and data acquisition. I'm on a tight budget, so I thankful if someone could help me to recommend components good enough to build my system.

    Thanks for your help.

    At these rates, you will need to run the sensor for the cDAQ.  You can configure the analog output on the Tritex nationally on the position.  There is an adjustable filter that you can set in order to get a clean enough to 300 Hz signal.  When you learn about the Tritex, make sure that let you them know what comms and e/s that you want to use.  If I remember, not all options have worked together.  The analog output may need to be my, but you can put a resistance through the acquisition of input data to get the voltage instead.  I don't remember all the details.  You should really not too much on the Tritex/LabVIEW side.  You will send your movement parameters (beginning of end of race, speed, position, accel, cut), and if you cycle (I believe you) or simply running in a loop.  You could also just be able to use the functions of jog.  When you get close to knowing exaclty what you need, PM me and I'm sure we can work something out with the drivers.  You need only the basics.  In fact, you could probably do this all your movements via digital and analog i/o.

  • data acquisition won't taste at the specified rate

    Material: C - DAQ 9178, AI 9239, inside a servo and an encoder potentiometer module

    Setup: I use the 9239 to measure the angular position of my servo and encoder of trees by streaming came pressure pot of the servo and my encoder. I put the sampling frequency on the DAQmx - Schedule VI to 100 Hz.

    Problem: I don't think that my DAQ is sampling data at 100 Hz because my VI registers more than 10 000 data points for a 10 second test. In addition, every time I have save my data in a text file, the vector of time my test data resets after a number of iterations.

    To debug, I tried the following configuration:

    I've defined the sampling frequency of 100 Hz (or is that s/s?), the samples per channel (size of buffer for continuous mode) at 2000 samples, number of samples per channel up to 10 and loop milliseconds timer on my VI at 10 m accordingly, data acquisition would send 100 samples per second (or 1 sample every 10 ms) on my PC buffer (which could store 20 X that amount). Then LabVIEW would read up to 10 samples per loop iteration (which is itself ~ 100 Hz) and work with these 10 samples inside the loop. However, since the loop is operating close to the sampling frequency of data acquisition, then LV should only work with 1 sample each iteration of the loop (100 Hz / 100 Hz)-not the 10-sample-max that I specified.

    However, I stumbled on "error-200279: the application is not able to cope with the acquisition of material" when I ran the program. Why?

    My code and materials should be easily able to cope with data acquisition - at least the way I put it in place

    This whole situation wondered my fundamental understanding of data acquisition timing, so I would really appreciate an explanation of exactly how to deliver DAQmx uses data synchronization, why my DAQ sample at 100 Hz, and how can I fix the calendar specified by the user.

    Thank you!

    aeroAggie wrote:

    The C - DAQ 9178 there some minimum sampling rate I will not meet?

    It's actually the 9239 that limit your sampling rate.  Read the data sheeton page 5 there's available data rates.  In short, your data rate allowed is 50kS/s / n, where is goes from 1 to 31.  50 k/31 gives you 1.6kS / s.  So, it's the minimum sampling frequency that can be used.

  • Digital relay of data acquisition

    Hello

    I quickly ask you questions. Can I connect several relay digital for single block scb - 68 (data acquisition is: 6321 PCI)?

    With Labview, I want to enable or disable each of these relays.  Is this technically possible? because never, I have connected several sensors to scb - 68.

    Each relay acts as a binary switch to a motor brush continuous (3-12 v and RPM motor voltage: 11.5 krm with weight)< 80="" grams).="" the="" dc="" motors="" will="" receive="" power="" from="" external="" dc="" power="" supply="" unit.=""  so="" the="" power="" for="" the="" relays="" (i="" am="" thinking)="" must="" be="" from="" daq.="" but="" i="" know="" daq="" can="" supply="" only="" very="" very="" less="" current.="" i="" am="" trying="" to="" source="" out="" if="" i="" can="" find="" relays="" that="" run="" with="" very="" current="" (which="" could="" be="" supplied="" by="" the="" daq="" itself)="" can="" you="" suggest="" me="" if="" this="" is="" possible?="" and="" also="" any="" information="" or="" source="" for="" the="" required="" digital="" relays="" would="" be="" lot="">

    Thank you

    MSC


  • Data acquisition on OR sbRIO 9636

    Hello! I'm working on my school project and I do the acquisition on OR sbRIO-9636. How I choose the sampling of acquisition period? I work as an example on the Web site OR below:

    http://www.NI.com/Tutorial/4534/en/

    I can't understand it on what sampling period should I put in Host.vi and in Target.vi in order to have the good acquisition? For an example, I would like to have period milliseconds 10 sampling. The configuration of loop-time in Host.vi and how Target.vi?

    Thank you

    Chupka,

    Yes, the calculation of sampling looks good this way, find all your data every loop, but you want to make sure you have a case to avoid FIFO overflows if you read each data point.  With regard to the loop of the host, you do not want make sure that it is superior to the host loop so that if you encounter the jig in your curls, you won't have the time.

Maybe you are looking for