Realtek RTL8101 PCI Ethernet is in error during startup

Hi all
I have EDT recently bought by Satellite A200-1CN notebook PC series. I'm having a problem at the start of the system that has Windows Vista installed.
The Realtek RTL8101 PCI Ethernet v 1.02 (060510) gives error during startup. The error is to run is as follows

PXE - E61 Media Test failed

Can any help with this problem




Hmm you ve you have a problem with the Vista boot! :|

Usually, this message appears because the BIOS can not find a source of start-up as ODD or HARD drive and then try to boot from LAN.

Perhaps the BIOS can not find HARD drive due to a hardware problem.

Hmmm. First of all, you should try to change the boot order in the BIOS. Put the HARD drive as first boot device.
Save the settings and try to restart the laptop. If it is not possible to start the Windows Vista I guess that HARD drive is dead!

Have you tried to reinstall Windows Vista using the Toshiba Recovery CD? Check this box!

If all this procedures don't help I recommend you contact the ASP in your country.
The technician must check the laptop and if necessary, it should replace the HARD drive.
Your warranty is valid so that everything should be done for free.

Good luck

Tags: Toshiba

Similar Questions

  • I get the error "on the volume C: default transaction resource manager encountered an error during startup and its metadata has been reset. The data contains the error code. »

    original title: NTFS problem
    Every 5 seconds, I get a warning (event ID 136) that says: "on the volume C: default transaction resource manager encountered an error during startup and its metadata has been reset. The data contains the error code. »

    Immediately followed by an error (event ID 137) that says "on the C: volume default transaction resource manager encountered a one-time error and could not start. The data contains the error code. »

    I am running windows 7 ultimate in any way to solve this problem?


    This problem occurs if the Windows file system transaction log is damaged. The Windows file system uses the transaction log to retrieve the system transactions when a file error occurs. The system of common log (CLFS) transaction logs may be left in an inconsistent state. When the CLFS transaction logs are in an inconsistent state.
    To resolve this problem, delete the files .blf and .regtrans-ms in the folder % Windir%\System32\SMI\Store\Machine.
    After you restart the computer, the registry regenerates the deleted files. These regenerated files are in a consistent state.
    1. click on Start , type cmd in the Search box, and then click cmd in the list of programs .

    2. click on run as administratorand then click continue.
    If you are prompted for an administrator password or for confirmation, type the password, or click allow.

    3. at a command prompt, type the following command and press ENTER:
    fsutil resource setautoreset true c:\
    these steps assume that Windows is installed in the default location, drive C. If this is not the case, adjust the drive letter of the path of the folder to match your configuration.

    4 restart the computer.

    I hope this helps.

  • U2515H, black screen with error during startup until the Windows login screen

    It is a half frustrating work situation.

    Was doing this:

    display port HDMI card--> cable HDMI - HDMI--> HDMI U2515H port

    This configuration has worked in Windows 7, with a 2560 x 1440 resolution reached.

    However, when you perform a reboot of the machine, the screen went black and impossible to display the BIOS POST screen (these text showing the amount of RAM you have, what are the HD detected, etc.). In addition, there was an error message on screen, saying:

    "The current moment of entry is not supported by the display. Please change your timing of entry to 2560 x 1440, 60 Hz or any other listed monitor calendar according to the characteristics of the monitor"

    The message error and white screen persists until Windows loaded to the login screen. This means that I can't see even the Windows logo, or the safe mode selection screen if I press F8.

    It's so no way for me to go into the BIOS to change any parameter, or do a boot was secure.

    Tried to use a DVI-HDMI converter and also a DVI-HDMI cable to make use of the DVI port of my video card. Still the same error as above. Worse still, this implementation does not work in Windows 7, gives me a white screen.

    I'm sure the DVI port on my video card works, cos it can work with my old Samsung monitor. Inspired by the present, the steps to be followed to the letter, may force the U2515H to show the BIOS screen:

    1. stop down and power down the computer.

    2 port DVI video card-->--> old Samsung monitor DVI port DVI - DVI cable

    3. turn on your computer. The screen of the MESSAGE on the Samsung monitor.

    4. go into the BIOS by pressing del screen

    5 disconnect the cable DVI - DVI video card DVI port.

    6 port card video--> cable DVI DVI - HDMI--> HDMI U2515H port

    The thing is, if I have to keep the old monitor, why bother to buy the new U2515H from Dell?

    So, how can I get the U2515H to accept the signal from my video card during the POST screen and the start-up phase, without going through the tedious steps each time? Thanks in advance!


    motherboard: Asus P5K - E Wifi (latest version of the BIOS)

    video card: Galaxy 8800GT (DVI, HDMI)

    It seems that your motherboard ASUS has a slot PCIe x 16 blue. If one of the beaches mid PCIe x 16 graphics cards will suffice. Go here. I have this sort by Nvidia PCIe x 16 2.0 video cards, low to high price. You look for one with DP or CDM. Or simply go to a local store and search the PCIe x 16 video cards with DP or CDM.

  • I cannot roll back the driver for Realtek PCIe Ethernet driver on Windows Vista.

    Original title: Roll Back Option is disabled under the device driver properties

    I uninstalled the Realtek PCIe Ethernet driver by mistake & then installed the other driver I found site Web of Realtek. but now if I want back with the previous version of the driver, this option is not active. so is there another way to push back with the driver already installed?

    the link skydrive screenshot for your reference is
    Please advise with the solution.

    Hello Asif,

    Thanks for keeping us posted and share this information with us.

    Method 1-

    Disable the anti-virus software

    Enable or disable Windows Firewall

    Note: Make sure that recover you the computer to a Normal startup after you perform all the troubleshooting steps, because the computer can be a risk of infection by the virus.

    Now, try a system restore.

    Back to us for any issues related to Windows in the future. We will be happy to help you.

    Thank you.

  • Find the drivers for the Realtek RTL8101 ethernet card

    original title: realtek RTL8101 ethernet card and drivers

    Hi have a problem persisting since HARD drive crashed without wireless interface with or without routers ethernet controller drivers needs can't seem to find a driver that works


    Make sure you have the latest vista drivers for your computer which you can get your computer manufacturers Web site

    go to their website and look for a driver and software download section

    Enter your model number for the last look drivers vista then download and install

  • How can I fix REALTEK RTL8101 internet connection problem?

    Hi, I have recently reinstalled my whole OS system on the desktop Dell vista (Windows Vista Home Premium SP1, Intel Celeron processor bits)

    It is stating that "the network adopter"REALTEK RTL8101 FAMILY PCI-E FAST ETHERNET NIC (NDIS 6.0)"knows driver or hardware related issues."

    My internet connection on the primary computer works fine. But between my router and dell computer internet connection does not work. I do not use wireless. The computer is directly connected to the router by ethernet cable.

    What do you think is the problem? How can I solve this problem?

    Go to the website of Dell here:

    Then, download and install the drivers for the network card in your PC.

  • Satellite L30 - PCI drivers have an error


    I wonder if anyone can help me please.

    I have a satellite L30 and for some reason this morning it is say PCI drivers have an error and I have no internet. I usually connect them via the wireless network. I tried to install the realtek drivers, but it did not, as he says they are all updated.

    Any help on how to solve this problem would be greatly appreciated.



    go to Device Manager and check if there is a yellow question mark shown there. Also, read this article how to determine, unknown device, peripheral position, or the id of the provider.

    Perhaps, you try to install the wrong drivers.

  • migrate from Windows 10 failure error oxc ox400d 1900 failed in the second phase of startup with the error during operation of data on my windows desktop 7

    Windows 10 has failed 75% error oxc 1900-ox 400 d has failed in the second phase of startup with the error during the operation of the Migrate_data on my windows desktop 7 using media creation tool. Help please.

    Turn off the computer.

    Wait 10 minutes.

    Start the computer.

    The installation program automatically restores your previous version of Windows 10 or an earlier version of Windows.

    Launch the prompt with administrator privileges.

    Press the Windows key + X

    Click prompt (Admin)

    Type the following command:

    Rundll32.exe pnpclean.dll, RunDLL_PnpClean /DRIVERS /MAXCLEAN

    Press enter on your keyboard

    Exit command prompt


    • Turn off (preferably uninstall) your Antivirus utility before you perform the upgrade.
    • Reboot several times and try again.
    • Disable the general USB peripherals (for example - smart card reader).
    • If you are using a SCSI drive, make sure you have the drivers available for your storage on a thumdrive device and it is connected. During the installation of Windows 10, click on the advanced custom Option and use the command load driver to load the driver for the SCSI drive. If this does not work and the installer still fails, consider switching to an IDE based hard drive.
    • Do a clean boot, and then try again.
    • If you upgrade to the. ISO file, disconnect from the Internet during the installation, if you are connected in LAN (Ethernet) or wireless, disable both and try the installation again.
    • If you update via Windows Update, when download reaches 100%, disconnect the Internet LAN (Ethernet) or wireless, and proceed with the installation.
    • If this does not work, try using the. ISO file to upgrade if possible.
    • If you are connected to a domain, go to a local account
    • If you have an external equipment, attached to the machine, unplug them (example, game controllers, USB sticks, external hard drive, printers, peripherals not essential).
  • PCI ethernet controller

    just finished installing windows on my pavilion 750n millineum. I'm looking for the driver to access the internet. Ethernet PCI controller is what Miss me. can someone help me please, I would appreciate. Thank you and God bless you

    Your question is a bit confusing. You say you need PCI Ethernet, but then the dialup modem driver download. Now, you mention that you use an adapter of Netopia of Bell South for internet. You will need to contact Bellsouth for Netopia drivers.

    Other drivers for your computer which can be useful >

    Intel Chipset:

    Intel network card:

    NVIDIA graphics card:

    Choose the Codecs AC97, contract, then download the executable:

  • "Sync has encountered an error during synchronization: unknown error." Synchronize automatically retrying this action. »


    I want to switch to Chrome, Firefox, but I have a problem with the synchronization feature.
    It always displays the following error message: ' Sync has encountered an error during synchronization: unknown error. " Synchronize automatically retrying this action. »

    I already tried this work around, but it did not work: remove my account from syncing, completely reset my Firefox profile, import my favorites of Chrome (using an HTML file), set up a new sync account (using the same e-mail address then that previously deleted).
    But I still get the error message.

    I saw in other threads that could be a problem with the story, so I also tried to delete, but it doesn't work anymore.

    Here is my last sync-log file:

    Thanks for your help.

    I finally found a solution to this problem of synchronization:

    I downloaded the add-on 'Housekeeping' and run the integrity check routine, and it seems to have solved the problem.

  • Sync has encountered an error during the synchronization. Unknow error

    I get the following error message: 'Sync has encountered an error during the synchronization. Unknown error. Synchronize automatically retrying this action. "In addition, currently, my favorites are useless: I lost all my favorites and I can't add any new.

    Problems with bookmarks and history does not properly can be caused by a corrupted database places.sqlite file.

    You can check for problems with the database places.sqlite file in the Firefox profile folder.

  • Problem with sync error: synchronization has encountered an error during synchronization: unknown error. Sync automatically retrying this action.

    Hi, I started recently a problem with the sync on my desk. My partner Android and Mac laptop no problems when you attempt to synchronize, but office always gives the same error. I tried to disconnect from the desktop computer, erase all files, restart and then adding the Office to synchronize once more, but the error persists.

    All bookmarks on the desktop disappeared, but are still in my sync data and have no problem being viewed on other connected devices. It also tells me that the issue is not the sync server and that there is something unique to the desktop machine.

    I hope that this will not require a reinstall, but if all else fails, it's an option. I'll try to attach a log file once I put the question.

    I think the error message is in the title of the thread:

    Sync has encountered an error during synchronization: unknown error. Sync automatically retrying this action.

    Try creating a new profile as a test to check whether your profile is the source of the problems.

    See "create a profile":

    If the new profile works then you can transfer files from a profile in the new profile, but make sure not to copy corrupted files.

  • unknown error during the synchronization of large amount of bookmarks

    I have thousands of bookmarks, but has not been able to sync. I always get the error message: ' Sync has encountered an error during synchronization: unknown error. " Synchronize automatically retrying this action. »

    In order to solve the problem several times I reset the remote data, but always the same error after a retry.

    I also export bookmarks and re-imported (which replaced the existing bookmarks). Still the same problem.

    Any ideas how to fix?

    Hi Christophe,

    It may be a bug corrupting your data. Please, fill a bug by following these instructions:

    Generally the bookmarks are not the majority of the data synchronized (story takes a big piece of storage).

  • Solution for Power Saver error during installation


    I've read several topics on the error during the installation of this utility powersaver.
    I had the same problem even with a clean install of windows XP and I FOUND the solution.
    The error seems to disappear and Powersaver works great after installing the Hotkey utility:

    Let's hope this message where it's useful.

    Greetz DeLorean

    [Edited by: admin]

    Hi DeLoren

    Thanks a lot for this useful information. I thought that this relocation tool will solve the problem. As we can see the usefulness of the shortcut key is also very important.

    If you have several solutions or useful information, please share it with us. ;)

    Best regards

  • What can I do about 48 error during the update of the iphone 4S?

    What can I do about 48 error during the update of the iphone 4S?

    Hello! Try the procedure described in section of the Apple Support below:

    Solve the iOS update and restore error in iTunes - Apple Support

Maybe you are looking for

  • I can't move my touchpad while typing

    I bought a laptop (HP g094sa) purple and have downloaded the 'minecraft' game in order to play the game, you look around (using the touchpad) and walking (using the keys w, a, s and d) I can't use the touchpad when using w, a, s and d. Please help me

  • Z560-I want to install windows xp. How can I go back to windows 7 in the future?

    Hello My friend just bought lenovo Z560 laptop of the United States and to use it in India. The laptop has pre installed windows 7. Now I want to format my laptop and install a new copy of windows XP. I have a few general questions on the same. (1) i

  • How to move the taskbar in Windows XP

    Original title: taskbar my taskbar is the screen I want to back to bottom but don't know how?

  • The corresponding \ko-kr on win7/64 \en-us lenovo computer files can be deleted?

    The corresponding \ko-kr on win7/64 \en-us lenovo computer files can be deleted?  These Korean subfolders exist on my system whenever a US English there too.  They make me think that I'm being watched.  I do not use or need for foreign languages on m

  • Connection of 2 1310

    Hello I wanted to know if anyone can tell me if I can do what I am about to ask and if so, how. I have a site with users of the work in the building and works in a trailer outside the building. the trailer users want to use phones to get what they wa