Rear chassis fan Z400 always runs at high SPEED

Similar Questions

• Fans always operate at high speed after power failure

  HP Pavilion Slimline S5780T - Windows 7 Home Premium 64-bit

  After a power failure a night or more recent, our Pavilion Slimline case fan and CPU fan have both run at high speed all the time, starting from the system. The level of noise is intolerable.

  I opened and cleaned all the dust from the inside of the case, including the removal of the heatsink from the CPU. Everything is clean.

  I ran the following HP Vision diagnostic, test the system, including fans. During the test of fan, the fans ran at 100%, then fell to the former level normal, quiet, then ramp back up to 100%. So says HP fans diagnostic tests are OK when there is always a problem. And it is possible for them to run at slow, normal speed.

  I installed the free SpeedFan utility, but there is not place to adjust the fan speed manually.

  How can I find the problem and the fans run at normal speed, as they did before the power failure? Everything that controls the speed of the CPU fan and the fan is broken.

  Thank you and best regards,

  Stephen - Myrtle Beach, SC

  Strange things happen when power flucuations or failures occur.  Most probably the motherboard has been damaged by the PPE and that is normally not as repairable by a DIY.  If you could find a newer BIOS, that to solve the problem.  Since there can be no more recent BIOS, try to remove the battery from the motherboard for the night and then put the file in and reset the BIOS to see if that helps the default value.  Otherwise, it might be repairable.

• HP 8510W boot not until the cool, the fan runs at high speed

  I did a little research but didn't really much other than dust cleaning. I did this, even removed the fan and the heat sink.

  Operating system: 32-bit Win7

  Early days of cold, boots upwards, normally, the fan turns at slow speed. CPUID Hardware Monitor shows all the time in the range 30 c - 60 c. From a web browser will cause the fan to spped, finally at full throttle, CPUID HW Monitor says:

  TZ2_ up to 90 C

  TZ5_ up to 100 C

  Remote1 up to 90 C

  Other times remain in the range of 30 c - 60 c

  The task manager's performance tab shows 1%-3% CPU, 30-40% consumption of Mem.

  Close all does not help, time remain high and the fan continues to run at high speed. Reset does not succeed, it will cut down, try to restart and stop again. Finally, it will sometimes get a screen where Windows thinks it could not start and wants to fix/reinstall the files, or go back to a restore point. If to cool for 10 to 15 minutes, it will start normally with the low fan speed until something starts to run (CPUID HW Monitor and Task Manager do not cause the fan speed).

  So nobody knows what TZ2_, the TZ5_ and the Remote1 map 30 5 8510W mother? Is this a real plus temp likely situation, ot possibly a problem with bios/driver not reading sensor properly?

  Well well, so far, no response, but I seem to have solved the problem. I tried reverting heatsink composed of all chips connected to the conduct of heat with no improvement. By checking things right after a stop, I noticed that the graphics chip was too hot to the touch even with the new complex. This meant that it was not the heat pipe.

  Ordered a used one from eBay, put it in and now it's stay nice and cool, not more than 60 C.

  The part number for the heat pipe is 452227-001.

• undetected 512-rear chassis fan

  Hi all

  Today, I replaced a new cpu fan.
  and the new, a work very well, but it is a problem, if I turned on my pc, I got a message from bios, this:error 512 - undetected rear chassis fan).
  If I press F1 my pc will work normally and I see my windows 8

  can someone help me please?

  IHAVE: -.
  Windows 8
  hddr2 7168 mb of RAM
  1 GB graphics card
  convertible minitour of product name: hp compaq dc7800p
  sysem bios 786f1 v01.32
  Processor: processor intel (R) core (tm) 2 cpu 6400 2.13GHz

  HP support is very bad!

  I don't have any help from this support, because I fixed it!

  Thanks for nothing!

• Satellite A300 - fan always runs at full speed after full stop

  When I stop the Satellite A300, the fan always runs at full speed.

  Hello

  What? Cooling modules run, even in this case, the cell phone is off?
  Press the power button for at least 4 seconds, then the laptop must be turned off.
  Disconnect the power adapter and remove the battery
  Wait about an hour and reconnect the battery and AC adapter
  Then switch on the device after a certain time of use of turning the unit off and check if the cooling modules would stop too

• Satellite A100 - the fan runs at high speed after idle standby

  Hello

  My laptop is Satellite A100-912.

  The problem is when I suspend it for more the a few minutes when the fan is running at high speed. This occurs on both Windows XP and Linux GNU. When the temperature of the two nuclei will more then 51 degrees C fan slows down and begins to work as expected. Suspended for a short time (about a minute or two) the fan speed is OK.

  I've updated to the latest version of the BIOS.

  Hello

  What version of BIOS you have installed? Has recently been the machine in for repair? A few interesting facts where I need some information to help you...
  By the way: is your machine still in warranty?

  Welcome them

• New z500 - fan runs at high speed on startup

  Hello

  I just bought a new Ideapad, a MBYP9GE Z500, that I got no windows, when I turn on the laptop it works in the BIOS. The problem I have is that the fan starts in high speed immediately and it is very noisy at start up. Is this normal? I want to say how is possible that the fan is noisy so if I am not under what whether intensive? Maybe it's because I have not installed yet any system? Or is it my laptop malfunction?

  Thanks in advance!

  Hi neokenchi,

  Thank you for your response. Yesterday, I installed Windows 7 and the appropriate drivers, that solved the problem. The fan runs at high speed before installing a system was apparently the default heat setting, as you suggested.

  Thanks again!

• I have 4 GB of RAM, but when my i play any game, my CPU fan runs at high speed and my system gets shut down within minutes.

  I have 4 GB of RAM, but when my i play any game for example NFS most wanted, my CPU fan runs at high speed and my system gets shut down within minutes. Help me solve this problem

  If you overclocked?  If so, cancel that.  If the games you play are poorly written, it is not that you can do about it.  If you have not cleaned the dust and lint from your computer within a certain time, you should do that because it accumulates and causes overheating.  For desktop computers, remove the cover and carefully use compressed gas to blow off the dust, especially around the fins in the processor heat sink and air ducts.  For a laptop, I'll ring gas compressed through the ventilation openings.

  Good luck.

• S50 satellite - B 15 P - Fans running at high speed and system crash

  Hello

  I have a new SATELLITE S50 - B 15, i7-5500U, 8 GB Ram, SSD etc., IV and v have some problems with it.

  for unknown reasons the CPU fan starts to operate at high speed, even if the temperature of the CPU hit is not 35%.
  It also froze about 10 times since I got it (April this year).

  The only way to make it work again would be me to hold the power button down until stop and start it back up.
  Once launched upward there is no mention of potential problems in the newspapers of events other than the forced closure.

  I just wanted to know if anyone else has experienced problems?

  Thank you

  Chris

  The only way to make it work again would be me to hold the power button down until stop and start it back up.

  Forcing order restores the fan activity and performance?
  Hmm it sounds like there must be some sort of system emits probably the bottom of some process locks the CPU and therefore increases the activity of the fan.

  You could start the the Task Manager and in the process tab, you will find all background applications that would appeal to the CPU.
  Click the CPU column to display all the processes of loading the CPU.

  However, you can also try to change the option of cooling method that is available in Windows Advanced Power options.
  Go to control panel → power options.
  Click here on the power plan that is currently in use.
  Then click on advanced power options and access the cooling method.
  Here you can change it from active to passive.

  

  In addition, you can decrease the status of CPU max at 90-05%

  

• HP dx2000MT: why fan runs on high speed

  Hello, the fan in this machine works sometimes at high speed, can someone tell me why or what I can do to stop this please?

  The most common cause of a computer running at max speed fan is a processor overheating.

  This can be caused by:

  -Extended heavy load on the processor.

  -Malware can cause this.

  -If you use many programs at the same time as background tasks, who will do as well.

  -Dirty/dusty in the computer heat sinks.

  -Malfunctioning components from the motherboard.

  -Bad placement of the computer.

  -Desktop computers should be placed where they receive lots of air circulation.

  -They should also be placed away from heater vents / air conditioning floor. AC vents may be tempting to cool the machine but will cause condensation and destroy it.

  -Observe the fresh air intakes where on the computer. Generally low and/or front of the chassis. If there is a substantive contribution, move the unit out of the carpet and on a hard surface.

  -Do not keep the Tower in a small enclosed space. Computer Cabinet should never have the door closed with the runinng machine.

  -If it was a laptop, you also to maintain it on a soft surface such as beds and prefer to use it on a desk, or on the binder or other similar when surface into the fold.

  -Vista-era of HP computers are completely garbage as well. (Sorry HP, but it's true). Watch by substituting a newer computer. The new HP machines are not nearly as terrible as those made when Vista was released.

  -Hydranix

• Fan is always running on my Satellite Pro L670-17R

  Hi all

  First of all, I'm french, so excuse me for my poor English. I'll try to explain my problem. I've just bought a satellite Pro L670-17R, core i5 450, ati 5650.

  As I only work with the word or surf the web, fan runs always every two minutes. I checked the temperature of the processor (with pc health monitor from toshiba), and it gives me 37 ° C which seem quite normal.
  I'm trying to change an option in the Panel, but without success, anything in the bios, to set the speed of the fan over the CPU usage.

  If you have any ideas or suggestions, it would be great.

  Next

  France Fabrice

  If you want to reduce the speed of the fan cooling use the balanced power plan and go into the advanced power settings.
  Energy saving of Toshiba you will find the option called cooling method. Assign the optimised battery.
  Cooling fan should run on low speed.

  Check it out.

• Re: Satellite L550D-12F - fan is always running

  Hello!

  We have a Toshiba L550D-12F and we are quite satisfied with the device itself - if it wasn't noisy fan. The fan ALWAYS runs audibly and I can't find any setting in the BIOS to its control.

  For my pain verxy I do not also find a support contact form to contact Toshiba so I hope that someone here will have a solution... Thank you very much!

  Sincerely,
  Matthias

  Hello guys

  I hope that my advice will help a little. I recommend you to use the laptop with the balanced power plan. Pleae change also advanced for this plan. In the advanced settings, you will find Toshiba power saver and the cooling method options. Place the change on the lower level.
  It should reduce the activity of fan.

  For example, when I use my Tecra A11 at the office for Office and mail applications I use for laptop and power management standby runs very quiet but the performance are always good.

• IdeaPad Flex 2 - 14 d: constantly running at high speed of the fan: 8.1 Windows

  Hello.

  I have a Flex 2 - 14 d running Windows 8.1 Ideapad and real pilots.

  The fan runs constantly at high speed.

  So I have no complaint about overheating, but instead, I have to complain about is cold knees.

  Y at - it a possibility to adjust the fan speed?

  Best regards

  Eleichstetten

  I have Flex 2-15 and suffered from the same problem. By trial and error, I found that (although not documented) a specific version of the TPFanControl (http://www.staff.uni-marburg.de/~schmitzr/tpfc.html) does not work with my laptop. Opt for the 0.62e version. It is a cool utility, has several conditions of default security in standard BIOS procedures if something is still wrong. Temperature to the fan speed mappings are user adjustible, so you must refine your laptop (default values are designed for Edge E520, so don't not necesserily ideal).

  A HUGE relief!

• Lenovo Z500 fan only runs on high speed

  Hello.

  Recently, I removed the lid of my laptop to clean my fan and to change the thermal paste on the proc and video. But when I replaced everything back and booted up the laptop, my fan only works on speed continuously. No rattling, it works just like my proc is very responsible, but no hot wind, cold. I checked the temperature in the Speedfan program and everything seems to be ok, but I noticed that there is no fan detected. Same thing, I saw in Everest. I tried to watch BIOS, but there is nothing in the fan or temperature associated (I change my bios there is a moment so my F1 - F12 keys would swap with FN keys). And also, in the management of energy, I tried to remove the dust, but just ran fan as it removes dust every time, none of the changes, same high speed. I tried Driver Pack Solution, no results on the fan. Everything went very well before I cleaned it, I was just trying to make my computer train less.

  Please help me, thanks in advance.

  Alright, removed the lid once more and discovered that the fan wires melted because of the heat the tubes that will proc and the video, so the wire that controls the speed of the fan has been disconnected. Anyway, case closed, just need a new fan, will not appear anywhere it's for sale, but that is another issue for another day.

• R720xd Fans incredibly strong, running at full speed

  My R720xd runs all fans of Board of Directors full speed continuous system.

  On switching on, fans at high speed for a second bump, then settle at reasonable speed and stay at reasonable speed during POST, up to the point where the iDRAC initializes, how they all kick at full speed and stay there. From there, the fans are going full speed. Nothing less than a reboot or shutdown will stop them.

  I am not exaggerating even slightly. Fans run to 17 000 rpm, 24 hours a day. It's so loud that you can hear it through the walls across the building.

  It has no operating system installed on this machine.

  I've upgraded to the latest firmware, tried to change the profile of performance in bios and tried the whole hold the power all unplugged thing so button.

  There is no possibility that it is overheating. Intake air temperature is 22 degrees, exhaust is 27, time CPU are 35-40 degrees.

  I found other references to people with similar problems with R720s, but it doesn't seem to be any single common cause for it.

  Any suggestions?

  I just followed on the resolution of this problem. The configuration of firmware and hardware were very good, the problem ended up being a faulty motherboard.

  Dell sent a technician to replace the motherboard, and once this is done, the fans were running normally. Technology said he is seen several times, and the replacement of the motherboard is the fix.

  I hope it helps someone else.

  Thanks to Chris and other people at Dell for working through this.