Reclassification of PERC H700 in T710 6

Similar Questions

• Upgrade T710 SAS 6/iR to PERC H700 problems

  I'm trying to improve and replace a RAID controller Dell SAS 6/iR (Dell PowerEdge T710/Linux Fedora) one with a PERC H700 (SAS6/iR supports only 2 disks to or smaller). The disks on the SAS6/iR are on the H700 and all RAID 0. I did all of the BIOS and firmware updates.

  When I enter the r RAID manager and each physical disk is mapped to a virtual disk. When I reboot, disk sizes are reported correctly in the system, but the partitions are listed as 'unknown format' and are unreadable. (I'm starting off the coast of the SATA because I'm tired to destroy the system disk. I know that I might have to do a complete OS resinstall anyway.

  I tried to set up foreign auto import to on and off.

  Making matters worse, after I removed the H700 restore 6 I / R, 6 I / R no longer sees the drives.

  The manual of Dell for the PERC H700 says

  "The virtual disks created on a PERC 6 and H200 controller family can be migrated to the PERC H700 and H800 cards without risking data or loss of configuration."

  But this doesn't seem to be the case for me. Any suggestion would be appreciated.

  The SAS 6/iR is NOT on PERC 6 - they are very different controllers.

  Migration of a SAS 6/iR to a PERC 6 / i is possible for Windows volumes, but only not bootable volumes. Although there is a small chance that it can work in all cases, a SAS 6/iR to a H700 migration is not supported, and it is more than likely, it will not work.

  My advice: Install your H700, configure RAID, then reinstall.

• PowerEdge T710 PERC H700 RAID level migration issue

  In my new role, I inherited a number of servers managed until now by someone else.  One of them is a PowerEdge T710 with a Controller PERC H700.  There are two matrices; the other has four 3TO disks in a RAID-5 configuration.

  I don't need the storage space any where near as much as the reliability factor.  Is it possible to do a migration on-site from RAID 5 to RAID-6 without disturbing data?  There is enough free space, and I have no problem losing a portion of the free space I have.

  "Is it possible to do a migration on-site from RAID 5 to RAID-6 without disturbing data?"

  Yes, BUT you can use this method by ADDING another disk.  RAID 6 requires a minimum of 4 drives.  Insert a disk "to hot', then in the software OpenManage (OMSA), go into storage, PERC, virtual disks and reconfigure in the drop-down list of tasks available for RAID 5.

  "There is enough free space, and I have no problem losing a portion of the free space I have."

  Apart from the fact that RAID 6 requires a minimum of 4 drives, even if you want to spend a 4 drive RAID 5 has a 4-drive RAID 6, it could NOT be done.  You can't make a smaller table.  The controller doesn't know - or care - on real data of BONE on the disks (so the amount of 'free space' is not serious) and is not worried about virtual disk space (which would be filled if the total capacity of the discs has been used).

• PERC H700 driver during Windows Server 2012 r2 - disk Raid not recognized not

  Hello

  I try to install a r2 Windows Server 2012 to a Poweredge R710 with a Raid Perc H700. 2 HDD in Raid 1, but the HARD drive is not rcognized Italian Installation even if I try to use the 2008 r2 for the Perc Raid driver. They are listed, but if I select one disk HARD are not visible. What should do?

  Best regards...

  Grolle,

  Leave in the Raid Controller, what is the status of the table? In addition, was the raid 1 initialized after being created? If this isn't the case, then, who will have to be done before you try to install.

  If you download this and start on the lifecycle controller (F10) and then select deploy BONES, load these files there and proceed with the installation of the OS.

  http://www.Dell.com/support/home/us/en/19/drivers/DriversDetails?driverId=M5VGR&FILEID=3325059394&osCode=MWS80&ProductCode=PowerEdge-R710&LanguageCode=en&CategoryID=DD

  I would like to know how will install it.

• Dell Power Edge R410 & Dell Perc H700 modular F2WGY

  Hi guys

  Need some advice please, a few weeks ago, we bought a Dell R410. This came with a modular 6/ir Perc. However, when we arrived at the installation of drives we noticed that the controller did not recognize disks larger than 2 TB. It's not good because we need to use 2 x 3 and 2 x 500 GB disks in a RAID 1 Configuration.

  After Googling autour, I came to the conclusion that the card that it came with the "Perc 6/ir' does not support disks larger than 2 TB.

  So, I advanced and bought a new modular a "Dell Perc H700 F2WGY" controller which apparently supports disks more great.

  the controller came yesterday so I removed the old Perc 6/ir controller from the slot in the bottom of the map editing and trendy "Dell Perc H700 F2WGY" modular at the same place. : Photo of slot, I inserted H700

  H700 card: see picture

  PERC 6/ir map: see picture

  Anyway, once I inserted the card and started, I was presented with the error; "PCIE training error" system HALT.

  Obviously this would not start any further. So I brought the wrong card? im confused at the moment between modular and integrated? the pcie slot is low for integrated only cards?

  I then add the new map on the PCIE Top slot. the system then started and he could see the card. However, it found no readers?

  What exactly I do bad will this card work at all? or I'm out of luck and need another card?

  Cappilio,

  The problem you are experiencing is due to the model of the H700. Map H700 modular version is actually designed for the blade server Poweredge series. The model that you would need is the H700i which is the version that is integrated, designed to go into the white storage controller slot you are talking about. The references are KK67X and CNXVV. The latest model of the H700 is the H700A which is the adapter, it's the model that is necessary for installation in a PCIe location.

  This link explains in detail in the overview H700 - http://www.dell.com/downloads/global/products/pvaul/en/perc-technical-guidebook.pdf

  Let me know if it helps.

• Add the disk to the PERC H700 of RAID integrated table 5

  Hi all.

  I have currently a Dell PowerEdge R710 configured with 4 SAS - 2 10 146 k Seagate 2.5 "drives in a Perc h700 integrated Bay RAID-5. I ordered a SAS-2 10 146 k disk Seagate 2.5 "to add to the Bay RAID-5 storage, making it a 5-disc set. What is the best way to add the drive to the RAID-5 array without losing any data? I have OpenManage Server Admin on the server.

  OS: Windows Server 2003 R2 32 BIT

  You can use OMSA... go in storage, PERC, virtual disks and select Reconfigure in the drop-down list of tasks available for your RAID 5.  This will add the disk to your RAID 5, then you will need to adjust the partitions in Windows once it is completed.

• R410 Sostituzione con PERC H700 hard drive

  Supporto Gentile,

  If line a detailed by the sostituzione di un disco compatibile con quello hoist by R410 Server con controller perc h700

  Speaking Saluti

  Gianluca Ticconi

  Buongiorno, the sto contattando by mail

• PERC H700 RAID 5, 3 disks, 1 Reporting failed and 1 predictive failure

  Hello:

  I have a PowerEdge T410 with a PERC H700, RAID 5 with 3 disks.  The controller reported a failed drive so I replaced the week last with a drive of new/refurbished.  Now only 1 week later it reported another drive has failed and the drive replaced as predictive failure.  Looks suspicious, i.e. I am doubting the controller card.

  I think updating the firmware of the controller first, but not sure if I should replace the faulty drive first, i.e. If updating the firmware could cause table failure.

  Also, if I install OpenManage on a virtual machine (host is ESXi 4.1), OM sees the controller?

  Thank you!

  Start on our live image and export logs of the OMSA facility there. http://www.Dell.com/support/home/us/en/19/drivers/DriversDetails?driverId=CWF92&FILEID=3550743303&osCode=WS8R2&ProductCode=PowerEdge-T410&LanguageCode=en&CategoryID=di

• HARD drive failure e battery perc h700 [CF]

  Buongiorno,

  e' possibile situation UN preventivo by a hard e batteria equal o compatibility disk?

  PERC H700

  DELL ST3600057SS 600 GB SAS hard drive

  Power edge R510 (service tag C3YGW4J

  Grazie

  Ramon Cartabia

  the sto contattando by mail.

• Support for large hard drive PERC H700

  Nobody knows the biggest SATA drives supported by a PERC H700 in a PowerEdge R710? I read on another post that the H700 will support 3 TB disks. Would like to know whether he would support also 4 TB and disks of 6 TB.

  Thank you

  Simon

  Hello.

  I can see 4 TB SATA HD as supported but not 6 TB. It may be supported but not yet committed.

• PERC H700 adapter w / Cable X394K

  I am upgrading a PowerEdge T310 for a client that was originally shipped with a single HARD drive and no RAID controller (only one hard drive is connected to the mobo).

  I bought a Controller PERC H700 and the cable X394K and hung.  It doesn't seem like something to connect readers to food, with the exception of a connector 12 pin labeld "P3A.  But the server doesn't have a connector anywhere so that I can connect only.  The only thing available is a connector 8 pins on the socket.

  Is there an adapter cable to go from the 8 to 12 pins pins? Or do I need something else than the X394K cable, which provides the SATA data connector and power in a single molded unit?

  Please notify.

  Thank you!

  Hello

  The cable you have (X394K) is not designed for a T310. T310 cable with the right connector is Y690K.

  Thank you

• PERC H700 drive failure

  Have a PowerEdge R510 with a PERC H700 / RAID 5. Newspapers showed the road 3 has failed, but turned upward. We have replaced (hot swap) with a new one (from Dell). Server administrator still shows as having failed, but turned upward, the logs show nothing except flashing in car 3 / unblinking the defective drive until it was removed (logs do not show the removal / departure of replacement or regeneration). Is there something we're missing in the H700? Thank you.

  Hello

  Install the latest version of the OMSA and check the State of VD. See the link for download with instructions for installation at the bottom of the page.

  http://downloads.Dell.com/FOLDER03252959M/1/OM-SrvAdmin-Dell-Web-WINX64-8.2.0-1739_A00.exe

• PowerEdge R310 and Perc H700

  I have an older R310 which does NOT support the hot-swappable drives and I'm looking to add a raid card Perc H700.  A few quick searches show only cables for installation bottom of basket.

  So I'm not the guy of material more experienced so there cables that go from the H700 to readers SAS?

  Hello

  It should be X394K part number. The description is HARD drive cable. PERC H200/H700 HDD card

• PERC H700 reconfigure RAID5 to RAID6

  We currently have a Dell PowerEdge R610 (PERC H700 embedded controller) with SAS 6 x 300 GB disks in a RAID5 configuration. We want to replace it with 6 x 1 TB drives in a RAID6 configuration. We must do so with as little downtime as possible (preferably no). Is it possible to Exchange each small disc out with the largest disk and perform a direct reconfiguration of 5 + 1 RAID5 to RAID6 4 + 2 configuration?

  States of the documentation you need to add a new disk to reconfigure from RAID5 to RAID6 RAID6 for a smaller virtual drive, but given that the new drives are much larger, it should theoretically be possible to reconfigure without adding a new drive all in maintaining / increasing capacity. If the controller supports that is my question.

  1. you cannot mix SAS and SATA drives in the same array, to replace a 300 GB SAS drive with a 1 to SATA will NOT work.

  2. IF you were to replace the 300 GB SAS drives with 1 TB SAS drives, you might reconfigure your table to include all of the space on the disks, however...

  3 If you reconfigure your 1.5 to 5 to VD VD, you MUST have already installed the operating system in UEFI boot mode. If you currently have your system in the BIOS boot mode, you should be limited to a 2 TB VD or need to reinstall the OS using the UEFI.

  4 reconfiguration of a 6-disk RAID 5, RAID 6 requires the addition of a 7 disk, regardless of the involved disk space.

• Batteria PERC H700 Poweredge T610 [MS]

  Buongiorno

  avrei need by UN nostro recent batteria del PERC H700 integrated su UN PowerEdge T610 Service TAG

  avrei need di one ' offer is there prima possibile procedere con the price by.

  Grazie

  Massimiliano

  Buongiorno,

  Con passing it mouse sopra identifier c Supporto Dell'e the voce "private message", it could mandarmi come message privato di seguito required information?

  By the spedizione:
  1. company name:
  2 address:
  3 City:
  4 Provincia:
  5 cap:
  6 name/last name/number phone/e-mail del referent in loco:

  With the fatturazione
  1 nome società:
  2 via:
  3 City:
  4 Provincia:
  Heading 5:
  Name/last name/number 6 telephone/e-mail del referent by the fatturazione:
  7 partita IVA

  Speaking saluti

  Manual