recomBR error to REMOVE when using recovery on Satellite M70 CD - 395

Similar Questions

• Fitness by using disk recovery on Satellite M70-169

  Hello

  I have a Satellite M70-169.

  According to me, I have messed around a bit with software such as cleaners of register etc. and want to make a new start.

  Exactly how, step by step, using the recovery disk came with the laptop?

  It will reinstall all that originally shipped with the laptop?

  Any help is greatly appreciated!

  Pesche

  Hello Pesche

  Instructions how to install Os using supplied recovery media, you can find under http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=2513&tstart=15

  I recommend to use the Expert installation mode and create a clean partition. When the computer starts for the first time you will be able to see the C partition only. The D partition must be created also in the OS, but is really not a problem.

  Exact explanation which you will find under:

  http://www.theeldergeek.com/hard_drives_07.htm - create an extended Partition (step
  http://www.theeldergeek.com/hard_drives_08.htm - create logical drives in an extended Partition. (Step 2)

  If you have any other questions, please write again.

  Bye and good luck!

• How to create recovery for Satellite M70 CD

  Hello

  I recently got the Satellite M70 on of my friends.

  But he lost his recovery cd and I would like to start with a fresh install...

  How can I create a CD of recovery for this laptop?

  Thanks in advance

  Well, you have tow options.
  First of all, you can order the CD from recovery Toshiba as suggested by the above user.
  As far as I know it s not expensive.

  Second possibility might be to create your own recovery CD using a 3rd party such as Norton Ghost for example application.
  Creating own recovery CD would be possible since all Toshiba drivers and tools are published on the European driver Toshiba page.

  So it s your choice now ;)

  Good bye

• Internet LAN conection problem when power is connected - Satellite M70

  Hello

  I recenetly bought a satellite M70 - 360. For some reason, internet connection (LAN) only works when the computer is running from the battery to the moment where you plug in the AC adapter, it is cut (you can also hear that there is some type of distortion on the line when the power is on)-its impossible to conect to the net, even if you already have AC. Have searched all previous messages and found that another person has reported the same issue, but no one answered at his post... ideas?

  Would be very grateful for any advice.
  Mark

  Hello

  Very strange. Have you checked the State of LAN card in Device Manager if the captain was connected? A yellow exclamation point appears in the net
  Section of the cards to work?
  In the properties of LAN card, you will find an Advanced tab. There you can activate and deactivate some additional options. I think you should check the options and possibly allow it.

  You said that the internet connection does not work when the power adapter is connected. But what about connecting to the local computer network?

• Satellite A55-S106 A:/ghost error when using recovery discs to reinstall the OS

  I have a Toshiba Satellite A55-S1065 that I recently replaced the hard drive, and when I try to use the recovery disks it keeps failing at various points with the A:/ghost error, even if this machine is not a drive A

  I really need help can anyone?

  Hello

  Have you used a compatible HDD and supported?
  A bit of problems of recovery happens sometimes due to hard drives not supported.

  In any case, in my experience, new hard disks must be formatted too.
  The Toshiba Recovery CD contains only an image file and I would recommend formatting the HARD drive, first with the help of another like WinXP or Linux bootable CD...

  Welcome them

• Satellite L505 - 10K - unexpected error when using recovery disc creator

  Toshiba Satellite L505 - 10 k

  Can't do any recovery disk when I open the toshiba recovery media creator, it says: an unexpected error has occurred. Close the program and then restart it (error code: 0D00F6-49-00000015) and then I click ok and then, it is once again and then I click ok and it is once again and I click ok and then the program comes and when I create the disc it comes to audit, but then it says: cannot read the following file. E:------Boot-fonts-chs_boot.ttf (error code: 02015-20-00000000).

  I really need help, I'm afraid something will happen to my computer, so is there someone who knows something about this kind of problem?

  Grateful for your help.

  Hi putte32,

  To be honest I never received this error before but it sounds like that recovery creator disc doesn t work properly... You should try a HDD recovery to restore the factory settings. Maybe you are able to create the recovery disk.

  Otherwise, I would contact an authorized service provider. If you can t create the recovery disk, the guy should be able to help you to complete this procedure.

• Compaq Presario CQ71 - error 1002 when using recovery (windows Vista)

  Hi guys,.

  I just encountered error 1002 while using the recovery... Recovery successfully crossed reformattng my drive, but crashed before reinstaling the original content. It's okay if I'm trying to hard drive or dvd rom recovery, all this translates into error 1002. I did some research and it seems that it is a very common error in hp without adequate solution products. I think I'm out of luck because my warranty expired years ago... How can I solve this problem? For me, it seems that recovery content originally placed on my hard drive (and later burned on the DVD by me) had been damaged. I see 2 possible solutions here:

  -to order an another recovery of the drives together (although I saw a few reviews it did not)

  -buy the new "Windows" and install a new fresh install (I will be able to perform the new installation at all?)

  I'd really appreciate pointers as I really don't want to lose my money for a solution that would work!

  Kind regards

  Robert

  Hello

  You can call the MSFT customer service and they will generally be able to find it for you.

  http://answerdesk.microsoftstore.com/msusa/en-us/answerdesk/answertech

• HP Pavilion dm4: Runtime Error when using Recovery CDs

  Hello. I had a HARD drive on this laptop failure. I have an SSD to replace with (on my own) and got the recovery DVD from HP. After 3 hours of trying to install the recovery DVD for the SSD only to fail in the last seconds, because he could not write a 'yes' to a config file, I found a 640GO HDD to recover the DVD to. Now, after starting very slowly in the recovery discs, I get a

  Runtime error!

  Program: x:\RITA-TOOL\Reducer.exe

  This application has requested the execution in an unusual way.

  For more information, contact the application support team.

  Any help is appreciated!

  I ask that your question is raised.

  Fact!

• Error code 800b0100 when using windows update

  Installation of Vista 32 bit, most of my windows updates do not settle. The files downloaded through Windows Update, which is set to be installed after asking, not automatically.  Update process begins, progress window moves toward completion, then at one point in the installation stops and the status display indicates failure of the installation.
  I could not install the updates for Vista Home premium 32-bit system.  Downloaded the State of preparation of system tool update, which the log file reports 5 errors, which seem to be missing files.  Question is how to get and install the missing files?

  Here's the extract log report:

  Checking packages
  (f) MOTHER of CBS missing 0 x 00000002 servicing\packages\Package_1_for_KB957321~31bf3856ad364e35~x86~~6.0.1.0.mum
  (f) MOTHER of CBS missing 0 x 00000002 servicing\packages\Package_for_KB957321_client_0~31bf3856ad364e35~x86~~6.0.1.0.mum
  (f) MOTHER of CBS missing 0 x 00000002 servicing\packages\Package_for_KB957321_client_1~31bf3856ad364e35~x86~~6.0.1.0.mum
  (f) MOTHER of CBS missing 0 x 00000002 servicing\packages\Package_for_KB957321_client~31bf3856ad364e35~x86~~6.0.1.0.mum
  (f) MOTHER of CBS missing 0 x 00000002 servicing\packages\Package_for_KB957321~31bf3856ad364e35~x86~~6.0.1.0.mum

  Control components store

  Summary:
  Seconds executed: 1989
  Found 5 errors
  CBS MUM lack count: 5

  Unavailable repair files:
  servicing\packages\Package_1_for_KB957321~31bf3856ad364e35~x86~~6.0.1.0.mum
  servicing\packages\Package_for_KB957321_client_0~31bf3856ad364e35~x86~~6.0.1.0.mum
  servicing\packages\Package_for_KB957321_client_1~31bf3856ad364e35~x86~~6.0.1.0.mum
  servicing\packages\Package_for_KB957321_client~31bf3856ad364e35~x86~~6.0.1.0.mum
  servicing\packages\Package_for_KB957321~31bf3856ad364e35~x86~~6.0.1.0.mum
  servicing\packages\Package_1_for_KB957321~31bf3856ad364e35~x86~~6.0.1.0.cat
  servicing\packages\Package_for_KB957321_client_0~31bf3856ad364e35~x86~~6.0.1.0.cat
  servicing\packages\Package_for_KB957321_client_1~31bf3856ad364e35~x86~~6.0.1.0.cat
  servicing\packages\Package_for_KB957321_client~31bf3856ad364e35~x86~~6.0.1.0.cat
  servicing\packages\Package_for_KB957321~31bf3856ad364e35~x86~~6.0.1.0.cat

  Interesting answer.  Anti Virus is McAfee Security Center v 9.15, last updated 19/11/09 (interesting to note that it is not updated since then...)

  You see the effects of 2 months-plus hijackware infection.

  Personal data backup (which none should be considered 100% reliable at this point) then format the HARD disk and do a clean install of Windows.  Please note that a repair installation (upgrade AKA on-site) will NOT fix it!

  HOW to do a clean install of Vista: section "If you want to reinstall Windows Vista by running a new installation...". "of http://windows.microsoft.com/en-us/windows-vista/Installing-and-reinstalling-Windows-Vista#section_3

  Once installed the clean, you will have the equivalent of a "new computer" in order to take care of everything on the page following before otherwise connect the machine to a network or the internet and before using a flash drive or the SD card that is not brand new, or has not been freshly formatted:

  4 steps to help protect your new computer before going online
       http://www.Microsoft.com/security/pypc.aspx

  NB: No matter what Norton or McAfee free trial which is preinstalled on the computer when you bought will be reinstalled (but invalid) when Windows is reinstalled. You MUST uninstall the trial for free and download/run the removal tool before installing updates, Windows Service Packs, or updates IE and before installing your new anti-virus application.

  Norton Removal Tool
       FTP://ftp.Symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exe

  McAfee Consumer product removal tool
       http://download.McAfee.com/Products/Licensed/cust_support_patches/MCPR.exe

  See also:

  Measures to help prevent spyware
  http://www.Microsoft.com/security/spyware/prevent.aspx

  Measures to help prevent computer worms
  http://www.Microsoft.com/security/worms/prevent.aspx

  Avoid fake security software!
  http://www.Microsoft.com/security/antivirus/rogue.aspx

  If these procedures look too complex - and there is no shame in admitting this isn't your cup of tea - take the machine to a local, good reputation and stand-alone computer (that is, not BigBoxStoreUSA or Geek Squad) repair facility.

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Have the intermittent connection when you use WiFi and conflict error IP address when using Ethernet

  I have intermittent problems with my wireless internet connection. I contacted the ISP and they analyzed the configuration of the modem-router, changed some and told me to try to reconnect. I try again and the connection is OK. The ISP has caress each other on the back and sent me on my merry way not-so-small. Problem is at an unpredictable time, problems (do) happen.

  Usually the failure scenario does not have a huge problem - plus one
  gene as a problem. I just keep trying to connect through Windows
  Network and sharing Center, and possibly the connection is made. But in some cases, time is critical; I eventually lose 10 to 20 minutes of typing-search-typing-correction-etc in a web form when the connection disappears before making a SHIPMENT. (Some time, after the failed wireless and re - connect, I was actually able to recover pretty quickly that the site has not been exceeded me.) So in this scenario I can't lost any strike.)

  I would like to connect my pc to the internet via an ethernet cable
  the modem-router. I could take this approach right after the wireless
  connection failed. Or in a preventive way, when I know I'll be typing-
  mode of research-type-fixed-etc and I want to be really sure. When I tried this, I get the error "Windows has detected an IP address conflict.

  What I do at this point to get around the Wi - Fi connection and connect through the Ethernet cable?

  The topic is edited for clarity of the moderator.* *.

  [Original title: LOST INTERMITTENT WIRELESS INTERNET CONNECTION]

  It is not clear what parameters your ISP technology management may have changed on your modem/router.  As a general rule, the ISP concerned the link between their server and your modem, but any fiddling with settings that control this link will not effect either on the link between your computer and the modem/router.

  If you still haven't reset your router to its default settings, do not unless you know the necessary internal router settings for you connect to your ISP.  If you have a cable Internet connection, the default settings may work OK, but if you have a DSL, they probably won't.

  You should not get this "IP address conflict" error when you connect the Ethernet cable.  Follow these steps:

  Open the "network and sharing Center" and then click on "change adapter settings".  You should see an icon for your wireless network adapter and an icon for your 'connection to the Local network' (your Ethernet connection).

  • Right click on each of the icons, and select 'properties '.
  • There should be a list titled "this connection uses the following items."  In this list, select "Internet Protocol Version 4 (TCP/IP)" and then click "Properties".
  • The radio buttons to "Obtain an IP address automatically" and "Obtain DNS server address automatically" should both selected.  If this is NOT the case, do so and OK your way out.  Furthermore, cancel your way.

  If a card has been configured to use a specific IP address, your "IP address conflict" should now be fixed (you may need to restart the computer for the change to take effect).

  If cards were already configured to obtain its IP address automatically, the problem lies in the configuration of your router.  You will need to access the router's Web utility to study and make changes.  To help you provide the brand and model of the router of the label on the back or the bottom.  Also do the following to a time where you have an Internet connection:

  Open a command prompt window (type cmd in the search box and press enter)

  1. In the black command prompt window, type the following command, and press ENTER after each line

  ipconfig/all > "% userprofile%\Desktop\ipinfo.txt".

  Notepad '% userprofile%\Desktop\ipinfo.txt '.

  output

  1. In the opened Notepad window, click Edit > select all (or press CTRL + A) and then click Edit > copy (or press Ctrl + C)
  2. In the body of your Question, right-click > paste (or press CTRL + V) the data of the Notepad window
  3. Close Notepad and remove ipinfo.txt from your desktop

• I get an error code 10 when using the network card.

  Hello

  When you use my internet dongle all my ports usb stopped working. cards network is to come up with and error 10 code. I uninstalled the adapter and re installed however it is always delivered with the same code. If I try to update it says I'm updating but the card still does not work

  Hi Sinead,

  Thanks for posting your question on the forum of the Microsoft community.

  I would like to know some information about the problem so that we can help you better.

  What is the brand and model of your computer?

  "Code 10" error is generated in the Device Manager in one of the following situations:

  -Device Manager cannot start the device.
  -One of the pilots who needs the unit does not start.
  -Device Manager has sufficient information to recognize the error that spread upwards by the device driver.

  Note: in this case, the "Code 10" error can be a very generic message indicating some sort of unspecified driver or device problem.

  I suggest you run this Microsoft fixit and check if it helps.

  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/mats/hardware_device_problems

  I hope this information helps.

  Please let us know if you need more help. We will be happy to help you.

  Thank you

• Error number invalid when using case when

  I have a table called NATIONAL_RARE_ECOSYSTEMS that contains 1 column called TEST_COLUMN (data type: varchar2):
  
  TEST_COLUMN
  rare ecosystem
  rare
  0
  0
  (null)
  (null)
  
  what I want is a query that will add a column called NRE_SCORE that will give each instance of line a score of 0 if it is null.
  If it is 0, then the score should be 0.
  If the line contains any text, partition should be 1
  
  I wrote the request:
  
  SELECT
  (CASE WHEN test_column is null THEN 0)
  WHEN test_column = 0 THEN 0
  WHEN test_column > 0, 1
  END) AS NRE_SCORE
  OF NATIONAL_RARE_ECOSYSTEMS;
  
  I get the error message:
  
  ORA-01722: invalid number
  01722 00000 - "invalid number."
  
  I think it is because on the 2nd and 3rd line, trying to perform arithmetic operations on a column which is varchar2 which I know that I can't do.
  
  How can I write a query that says: If the line contains text, then gives the score of 1?
  
  I'm using oracle 11g.

  Hello

  993451 wrote:
  I have a table called NATIONAL_RARE_ECOSYSTEMS that contains 1 column called TEST_COLUMN (data type: varchar2):

  TEST_COLUMN
  rare ecosystem
  rare
  0
  0
  (null)
  (null)

  what I want is a query that will add a column called NRE_SCORE that will give each instance of line a score of 0 if it is null.
  If it is 0, then the score should be 0.
  If the line contains any text, partition should be 1

  Any text other than '0', you mean. I guess that doesn't matter if this text is all the numbers, like '9876 'or something with no numbers, as 'rare'.

  I wrote the request:

  SELECT
  (CASE WHEN test_column is null THEN 0)
  WHEN test_column = 0 THEN 0
  WHEN test_column > 0 THEN 1
  END) AS NRE_SCORE
  OF NATIONAL_RARE_ECOSYSTEMS;

  I get the error message:

  ORA-01722: invalid number
  01722 00000 - "invalid number."

  I think it is because on the 2nd and 3rd line, trying to perform arithmetic operations on a column which is varchar2 which I know that I can't do.

  You are not actually doing arithmetic, but you compare your VARCHAR2 column, so he tries to convert the string to a NUMBER, and that's why you get the error ORA-01722.
  >

  How can I write a query that says: If the line contains text, then gives the score of 1?

  I'm using oracle 11g.

  Here's one way:

  SELECT       CASE
             WHEN  NVL (test_column, '0') = '0'
             THEN  0
             ELSE  1
         END          AS nre_score
  ,       ...          -- you must want other columns, too
  FROM       national_rare_ecosystems
  ;
  

  Since you are not really care on the numerical value, do not use numbers anywhere; stick with VARCHAR2s, for example '0'.

  I hope that answers your question.
  If not, post a small example data (CREATE TABLE and only relevant columns, INSERT statements) and also publish outcomes from these data.
  Point where the above query was to get erroneous results, and explain, using specific examples, how you get these results of the sample data in these palces.
  See the FAQ forum {message identifier: = 9360002}

• Get the error: SCAC-50012 when using the Java activity

  Hello
  
  I use Jdeveloper 11.1.1.4.0. I use a Java integration activity in my BPEL and when I compile the project, I got an error -error: SCAC-50012
  
  
  The code I use in activity integration of Java is
  
  
  ______________________________________________________________________________________________
  
  java.lang.String TraceLogMessage = null;
  java.lang.Boolean tracelogenabled;
  java.lang.String title (java.lang.String) = getVariableData ("Title");
  java.lang.String instanceID = (java.lang.String) getVariableData ("InstanceID");
  java.lang.String serviceName = (java.lang.String) getVariableData ("ServiceName");
  
  tracelogenabled = oracle.apps.aia.core.eh.logging.AIALogger.isTraceLoggingEnabled ("INFO", "http://xmlns.oracle.com/ExecuteSalesOrderFulfillmentDeviceUpdateEBF");
  setVariableData ("TraceLogEnabled", tracelogenabled);
  
  If (tracelogenabled.booleanValue ())
  {
  
  
  TraceLogMessage = "Start" + serviceName + "Instance:" instanceID + title;
  
  oracle.apps.aia.core.eh.logging.AIALogger.logTraceMessage ("INFO", null, TraceLogMessage);
  
  }
  
  ______________________________________________________________________________________________
  
  I imported the following bpel but there is no chance...
  
  
  < bpelx:exec import="java.util.logging.Logger"/ >
  < bpelx:exec import="java.util.logging.Level"/ >
  < bpelx:exec import="oracle.fabric.logging.LogFormatter"/ >
  < bpelx:exec import="org.w3c.dom.*"/ >
  < bpelx:exec import="oracle.xml.parser.v2.XMLElement"/ >
  < bpelx:exec import="java.util.*"/ >
  < bpelx:exec import="java.lang.*"/ >
  < bpelx:exec import="java.math.*"/ >
  < bpelx:exec import="java.io.*"/ >
  < bpelx:exec import="oracle.soa.common.util.Base64Decoder"/ >
  
  
  Please help me with this...
  
  Thank you and best regards,
  Suman

  Hello

  Have you checked the scac log files in your project JDev SCA-INF/classes directory? There could be vital information in these tell you what the problem is.

  Concerning

  Lars

• TestStand deployment error Code 1055 when using LabVIEW storage VIs

  After a few days of playing with TestStand deployment. I have final stalked the VI which was the origin of this error.

  He was using the LabVIEW storage screw to save data in a TDM file.

  My work around at the moment is to use a Wrapper VI and call this VI by reference.

  In this way the deployment TestStand cannot detect the Sie of storage.

  I'm using LabVIEW 8.6.1 and TestStand 4.1.1 does anyone know if this issue was address TestStand 4.2?

  It seems that the upgrade can be worth it.

  Simon,

  After investigating the matter further, I found that we had already encountered this bug. It has been fixed in 4.2 TestStand and LabVIEW 2009 I tested your files with 4.2 TestStand, LabVIEW 2009 and everything built successfully without any hiccups on the way.

• What I lose programs when using recovery discs

  You had to do a chdsk to get OS again due to the lost areas.  When replace the HD and reinstalling with the recovery discs I made shortly after receiving the HPE 170 t HP Pavlion I lose the Corel PSP program and other when / if reinstall right?

  Reinstall it puts the computer to the same State as when you bought it including all the bloatware that comes with the system.