Reconfigure Aspire SSD caching on Windows 10 v7

Hello

I have upgraded to Windows 10 on my Aspire V7 482pg (5861). I installed all the drivers recommended on the support page and have not run into any significant errors. However, this particular laptop comes with an SSD for caching, and I was not able to reconfigure it to do this. The software ExpressCache I used before on Windows 8.1 doesn't seem to be compatible with Windows 10.

Y at - it an another software caching that I should try to use? One of the downloads on the support page is Intel Rapid Storage (even though the description on the page shows a quick start, it is certainly a fast storage that has been installed). At present, the only thing Rapid Storage seems to do is reduce the amount of energy during periods of inactivity.

Should I try to configure the system to use Smart Response? It is even possible with this version of rapid storage technology?

Any help would be appreciated,

Thank you

Advertisement

Hello

I have the same laptop and I faced the same problem. I downloaded the driver for Acer ME600 ExpressCache from the support page, changed the installator and now the SSD caching works ok. Link

Hope this helps

P.S Intel Smart Response in ' t supported by our chipset

Tags: Acer Laptops

Similar Questions

  • Installation SSD/Cache in Windows 7 Home premium

    Hello

    I have a Lenovo laptop, Y510P, which came with a 1 to HARD drive and a 24 GB SSD.  I replaced with a 500 GB HD and installed Win7.  Is it possible to set up the SSD/cache for use in Win7?

    Thanks for any help.

    The system that you need is the Intel of the quick response technology but will depend on the ability of the chipset

    Dominic P thanks for this link

    http://www.PCWorld.com/article/248828/how_to_setup_intel_smart_response_ssd_caching_technology.html

  • Problem starting Windows 8 (associated with quick start + Intel Smart Response Technology SSD cache)

    Hello
    I have a problem with the fast start-up of Windows 8. When I shut down my PC everything works fine, but when I turn on the PC, Windows will load until a certain point and then suddenly start screen appears again. The second departure is always successful.

    I discovered, when I turn off the Quick start, the computer starts without error on the first attempt. It goes the same for when I disable Intel Smart Response Technology (SSD cache). There are no problems when I use Hibernate mode.

    Recently I did a BIOS update, so I don't know if there is a setting in the BIOS that is may cause this error?

    Thanks in advance for any help!
    Martin

    Hi Martin,

    Glad to know you solved the problem. Thanks for sharing of the resolution, because it would help the other members of the community to the same question.

    Please do not hesitate to answer, in case if you need help or information on this issue.

  • Y410p SSD Caching support

    Hello

    I just got my y410p. The model that I have included the SSD. However, while it is visible in the software intel so fast, there is no option to speed up. There is a tab named perfomance instead, and that refers only to a feature, no possibility to use the SSD as a hidden energy saving.

    The hard disk is configured as AHCI disc and I am running windows 8.

    Any ideas/thoughts?

    Thank you

    Arthenios

    Hi Arthenios,

    If the status of the fast Intel, your system may use the Expresscache to cache the SSD.

    I saw a Y510p using preinstalled express cache.

    to check if the expresscache is your SSD caching software, you can follow this Post

    http://forums.Lenovo.com/T5/IdeaPad-Y-U-V-Z-and-P-series/Y500-how-do-I-tell-if-automatic-SSD-cache-i...

    If it is properly cached with express cache you shouldn't worry.

    Hope this helps,

    Cheers!

  • Envy 15-j051sa mSata SSD Cache TS

    Envy TS 15-j051sa mSata SSD Cache for the 1 TB 5400 HGST HTS541010A9E680.

    The manual States "Support for the SSD drive 24-GB mSATA (not available on computer models equipped with system - 16834 memory or 12288-Mo)". As I have all the conditions, Intel processor, 8 GB of ram, the question is can I just install it and everything works as if by magic?

    Or what I need to do anything about it, or to perform any installation? I noticed Intel RST is running and that the system is working normally.

    Any help or experience would be helpful (apart from the disk of 1 TB of pit and replace it with a large SSD!).

    Thank you.

    OK, for someone else to end up here

    It worked for me:

    • Bought a 24 GB SSD mSata off eBay (very cheap).
    • Make sure that it is the type of partition MBR (I used an external box with Mini PCI-E to SATA 22Pin mSATA).
    • Make sure that the Intel Rapid Start technology is disabled in the Bios. (Appears only if the mSata is installed).
    • Windows 8 (.1) boot in SafeMode (this is where I'm wrong).
    • Run the Intel Rapid Storage Technology-> Performance-> activate acceleration.
    • Reset (it works!)
    • Activate the technology Intel Rapid boot in the BIOS (I don't know if it improves things, seems to work OK without him)

    A start power button to start screen for ready office is 17-18 seconds. Note that I have several services running SQL 2008 R2 Server and all the HP utilities installed as new.

    Paul.

  • Want to Phoenix 810qe: SSD cache fails on desire 810qe

    A few weeks ago I noticed a problem (probably unrelated) which led me to look at the system event logs and I was surprised to see that I was getting all them complain about a bad block on a "hard drive" I didn't know, I had three or four errors a minute.  A little poking around revealed that it was the machine provided with 16 GB mSATA SSD cache.  Apart from the log messages, the computer seems to work very well, so I put off to worry about this.  Now, with the end of my warranty approaching, I decided to call and see if I could get a replacement.  (I'm now up to eight messages per minute).

    After a few long and frustrating calls, I finally got someone to direct me to the good test to run, who immediately said "Test failed.  Recommended replacement car. »

    Unfortunately, they are not ready to send me a replacement, and I'm not ready to wipe my machine and send it to them to play with for a few weeks, I'm looking for other solutions.

    My questions are

    1. Do I need to worry about this?  It is a cache, so, theoretically, if it fails, it could simply not give me the performance boost, but it won't actually hurt anything.  But what I saw on the web implies that there are two ways that SSD hiding can be configured ("enhanced" and "expanded") and one of them may cause corruption if it fails.  The support guy I spoke had no idea.
    2. How is it difficult to replace the SSD drive with a new one?  They don't seem to be very expensive, and looking inside the box, he's not physically difficult to replace.  But I suspect that there's more involved in the passage.
    3. If not, can I disable the cache and get him out?

    Any help will be appreciated.

    Evan

    Just in case someone comes to this page with a similar problem...

    After another telephone conversation with a supervisor, HP agreed to send a part... purpose of replacement only if they could schedule a technician to come to my house to install it.  For free.  I agreed.  The tech came out yesterday morning, challenge a screw, jumped from the old disk, jumped into the other in screw them and started the machine.  Everything worked.  No software at all.  It's all plug-and-play.  They sent me a disc identical to that which failed (16GB), but he expressed the view that it would be putting end to a larger.

    It turns out that the machine uses no hardware caching, but rather the software called ExpressCache, where my confusion of not being able to determine what mode of caching (material) that he used.  This software manufacturer said that it "maintains safe and the integrity of all data in case of failure SSD or kidnapping, as well as unclean judgments resulting from power outages.  And that seems to be the case, at least in terms of pulling on a production car and its replacement by a new.

  • Y510P - How can I check the size of the SSD Cache?

    Hello

    I just took delivery of a Y510P but don't see anywhere how I check the size of the SSD Cache.

    The laptop should have come with an 8 GB SSD Cache but how to check this?

    Thank you very much

    Jon

    Brayjd, I, too have just received my Y510p, and after reading your post, became curious as well. After trying all the same things you did, without any good results, I went into the Device Manager and got the hard drive part number and google it. It turns out that mine is a hybrid SSD/HD with a SSD 8 GB cache built into the player. A hybrid has the SSD completely autonomous in the HD itself and requires no external software to run. That's why we have found no information on the size - for what is the rest of the computer is the SSD is invisible. Try Googling the part number of the hard drive. I hope this will answer the question for you, too.

  • 8 GB RAM with ssd and ram 12 GB without ssd cache cache

    We are looking to buy a laptop HP Envy 17 t j100 touchsmart for our son.  Which would be better:

    8 GB of RAM with SSD exceleration 24gig or 12 GB of ram without ssd cache memory?

    The cache of WSSD 24gig offers performance very similar to a full SSD drive for a much lower cost. I would buy the unit with the drive cache of the WSSD 24 concert and as little memory as they sell me and then increase the RAM me but 8 GB of RAM it's frankly more than many. In fact, it's probably better than 12 because there 2 identical modules allowing the functioning of memory dual channel. To summarize, the best option is clearly 8 GB RAm and the WSSD of 24 concert disk cache.

  • 16GB mSATA SSD Cache drive

    Hello, how will I know who my 16 GB SSD Cache drive mSATA recovery is on, there another drive another letter from the c: drive, I don't want to exhaust by accident... Thank you.

    OK thank you!, been awile since I had to buy a new computer, 12 years since then, I need to learn a lot of things...

  • How can I verify that my U410 contains a 32 GB SSD Cache?

    I just got my Lenovo Ideapad U410. I ordered one with 1 TB + 32SSD, and I'm very happy with it. I want to assure you that there are 32 SSD cache. How can I make sure it's 32GB SSD? Any ideas? Thank you!

    Access the bios, there will be some information about this

    Disk management will not be information in case you have ssdconfigured of RAM

  • Intel(r) HD Graphics Family Driver does not not for Aspire S7-392 in Windows 10

    Hello

    I have improved my Aspire S7 - 392 to Windows 10 a few weeks ago, and while most things seem to work properly, the driver for the graphics card Intel (R) HD Graphics Family had the yellow exclamation of 'something is wrong' next to him since. Now, I am unable to connect my laptop on the external monitor that I use for work (as nothing happens when I do), and graphics performance are visibly slowed (point of use) when playing games still fairly weak demand.

    Which would seem to indicate that there is a pretty big problem with drivers. I spent literally 10 hours on the phone with Microsoft Client service tries to understand the question, but all they could tell me after a fairly intensive survey was that they knew not what it was and wait for updates from Acer or Intel driver.

    I have the latest driver on the Acer support site installed (although it doesn't seem to be one specifically for Windows 10) and I rolled back and updated and tried several versions of the drivers from there, but all seem to have the same problem.

    I also downloaded Windows 10 Intel drivers that are supposed to be specially for my processor and graphics configuration, but when I try to install, it says that my computer does not meet the requirements (which is quite confusing when I have the exact material, so that the driver is designed).

    I searched these forums for support for other users of the S7 Aspire with similar problems and for people with features of Intel(r) HD Graphics Family have similar problems, but can't seem to find anything.

    My apologies if this has actually been discussed elsewhere, but no help at all with this issue would be appreciated. Windows 10 has been out for a while now, so I was hoping that a solution had been found to do this, since there must be a certain S7 users out there.

    Anyway, thanks in advance for any ideas/advice,.

    Oli

    1. download the "Intel Driver Update" utility

    2. go manage the devices and uninstall/remove your Intel graphics driver

    3. run the Intel driver update utility.

    Your current graphics driver is a custom OEM Acer/Intel graphics driver.  This is why it will not let you install.  If the generic driver update utility that installs does not quite work right, then you go back to the driver that is located on the site of the Acers.

    If don't want to use the Intel utility driver update, then you will need to download the zip file of the driver instead of the driver .exe... and then use the disk method 'have' to install it. It is probably easier to use only the update of the Intel driver utility.

  • downgrade acer aspire 571 - v3 for windows 7

    Hello

    I am trying to downgrade an acer aspire v3 - 571 of windows 7 to windows 8? Anyone know how I can change the boot order to boot from a dvd or usb hd rather than the hard drive?

    See you soon

    Nice day

    1. you press "F2" when you switch on the device.

    2. make sure that you change the secure mode of UEFI in legacy.

    3 disable secure boot.

    4. go to start, press "F6" to take the optical drive to option 1.

    Kind regards

    FReeZA

  • Please help driver Aspire E5 - 552G for Windows 7

    Help please, where I can download the driver all my Aspire E5 - 552G for Windows 7?

    hardwareIDs yellow exclamation when I install windows 7

    PCI\VEN_10EC & DEV_8168 & SUBSYS_095E1025 & REV_15

    http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=13&pfid=5&level=5&Conn=4&DownTy...

    PCI\VEN_168C & DEV_0036 & SUBSYS_E091105B & REV_01

    http://www.station-drivers.com/index.php?option=com_remository&Itemid=352&func=FileInfo&ID=2075&lang...

    PCI\VEN_1022 & DEV_1577 & SUBSYS_095E1025 & REV_00
    PCI\VEN_1022 & DEV_1578 & SUBSYS_095E1025 & REV_00
    PCI\VEN_1022 & DEV_790B & SUBSYS_095E1025 & REV_4A
    PCI\VEN_1022 & DEV_7914 & SUBSYS_095E1025 & REV_20

    PCI\VEN_1002 & DEV_6900 & SUBSYS_10561025 & REV_81

    HDAUDIO\FUNC_01 & VEN_1002 & DEV_AA01 & SUBSYS_00AA0100 & REV_1007
    HDAUDIO\FUNC_01 & VEN_10EC & DEV_0255 & SUBSYS_1025095E & REV_1000

    http://support.AMD.com/en-us/download/desktop?OS=Windows+7+-+64

    USB\VID_0BDA & PID_0129 & REV_3960
    This one is CRW USB2.0

    http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=15&PFID=25&level=4&Conn=3&DownT...

  • HOW TO CHANGE SATA to RAID mode (SSD CACHE PROBLEM)

    Hello

    I have a HP Envy 4 1054tx Ultrabook with 500 GB drive HARD + SSD of 32 GB. My HARD drive crashed and replaced it with a new one. Unfortunately, my restore disk does not work so I installed fresh new WIN7. I try to use the SSD caching capability of my laptop (which he did before, when I bought it).  Based on the forums I've read, the SSD cache implementation requires that the SATA controller must be set to RAID mode.  However, when I entered the BIOS, there is no option or the configuration that I can use to set SATA RAID my HARD disk mode.  In this regard, I can't meet one of the requirements of SSD caching.  Here are some of my BIOS Setup.  Can you help me please guys how to work on it? I am not convinced, on how my phone performs without SSD caching.

    Thanks in advance.

    Hello:

    Disk controllers hard HP consumer notebooks cannot be changed from their default values.

    More than likely if your model is equipped with a hybrid drive, the speed control is already defined with RAID.

    I recommend you to read this blog on how to get this Setup to work on a new install of W7.

    http://Forum.NotebookReview.com/HP-Pavilion-notebooks/676213-definitive-guide-clean-install-OS-MSSD-cache-equipped-laptop-dv6t-7000-dv7t-7000-Envy17-3200-a.html

  • On a 5600U ssd cache drive location

    Hi try to find the location on the motherboard for the ssd cache. Someone at - it ideas. Thanks a lot mat

    Sorry,

    Thank you very much for your time and effort

    Matt

Maybe you are looking for

  • My NOTES are all gone! Help!

    I have recently retired, and my e-mail account 'work' has just been disabled by my former employer. Now all my notes in the NOTES app on my phone and iPad have disappeared. I checked the other e-mail folders in the settings and they are not there, so

  • After that recommended BIOS upgraded satellite a series does not start

    During the recommended BIOS Flash upgrade of the system came in suspended state.I waited 1 h before trying to restart the laptop, I had to do with force by removing the battery.Now the system does not even show the bios screen. Is there a way to fix

  • Cannot enable the Web Server (SSL) site on El Cap Server

    ' tLooking for help here, trying to put in place in El Cap 10.11.3/Server 5.0.15 Web services and the no - SSL server comes just in green in the admn, but the SSL server will not activate. I have an a record for the server to an external DNS server m

  • Freezing in El Capitan

    I had a daily OSX freezes in El Capitan on my MacBookPro below. I thought it happened only in Chrome, but today it happened so that in my mail client, the mailbox. Everything is normal until the cursor freezes and the Mac everything becomes unrespons

  • How to specify the port in webview

    See the Web mode using a WebVPN connection interface: I use url = " https://X.X.X.X:4443 " but it doesn't seem to work, where X.X.X.X is the IP address. How should I specify port Web layout?