Recovery of the Internet and the Touchpad does not

Similar Questions

• Satellite C850D-11 q - keyboard and the Touchpad does not

  The laptop is a little more than a year and worked ok until recently.

  Symptoms were the keyboard and the touchpad does not not on page 8 of windows logon. Pressing power to put the laptop into sleep and pressing still often got their work.

  He progressed to the keyboard and the touchpad works do not randomly points while the use of the laptop.

  Finally cleared the HARD drive and restored windows 8 alone, the laptop still BSOD quite frequently - refuses to install the updates required for 8.1 and the keyboard and mouse often do not work even in BIOS Setup page. I reinstalled the RAM and HARD drive.

  Short of ideas, the keyboard and the touchpad work and so I guess that their connections are correct - but often they just stop.

  Any ideas appreciated?

  Thank you

  Hello

  > Finally cleared the HARD drive and restored windows 8 only
  I hope that you created before Toshiba recovery disks you have formatted the system.
  Did you?

  The recovery disks will allow you to reset the laptop to factory settings; on the same State as at the first day of the purchase.

  > First symptoms were the keyboard and the touchpad does not not on page 8 of windows logon. Pressing power to put the laptop into sleep and pressing still often got their work.
  Well, usually the keyboard problems are not problems system or software as the keyboard driver is part of the system and an additional installation of some drivers is not really essential and necessary.
  That is why in most of the cases the keyboard problems could be the causes of physical problems.

  However, after using the recovery disc and the parameters of the laptop back to factory State, both parties (keyboard and touchpad) should work perfectly.

  > the BSOD laptop still quite frequently - refuses to install the updates required for 8.1
  BSOD doesn't look very good. As mentioned above; parameters of the laptop back to factory settings should solve all the problems in the system. In the case where the BSOD appears even if the power has been turned back to factory State, a hardware problem could be the reason for this.

  I had also some problems with the update 8.1 Win. The system to win 8 could not find the Win 8.1.
  But the reason for this was simply. I had to install all updates to Win 8 and had to update the State system before trying to update to the next level following 8.1 Win

  So, what can I say: I will try to put the laptop initial configuration using the recovery disk.
  Then I would try to get automatic updates (a few reboots were essential too). After that, I would check the functionality of the keyboard and the touchpad. In the case where them parts would not work, I would contact the service to check if the two pieces.

• Satellite X 200-219 - the touchpad does not work as it should

  Hi all

  I recently bought a 2nd hand Toshiba Satellite x 200-219. Had some problems with it that I have overcome now, except one... The touchpad does not work as it should. I think that the cable has been damaged at some point.

  So I'm wondering if I should use the same ribbon cable to connect the keyboard to the motherboard or can I get one of a different model of PC Toshiba laptop?

  I tried searching on the net for advice but have resulted in nothing so thought I would try the forums.

  Any help you can give will be greatly appreciated.

  Thanks in advance,

  Lee

  I think you can use the items to the satellite X 205 series since this seems to be the same series as X 200:
  Found some related parts the touchpad:
  Satellite X 205 / X 200 touchpad Board with cable: reference number: K000047950
  Satellite part number for the TOUCH PAD FFC X 205 / X 200: K000047980

  But why you n t come into contact with a Toshiba authorized service provider in your country and order the part necessary and compatible?

• I have laptop (hp probook 4520 s), the touchpad does not work. How can I turn it back on it?

  I have laptop (hp probook 4520 s), the touchpad does not work. How can I turn it back on it?

  This is a question which would probably respond by HP support, because it isn't really a Windows problem.

  Are you sure that the touchpad is not just turned off? Many laptops have switches, power switch, so you can rest your palm while typing one is not worry by pressing the key.

  Sometimes, there is a button above the key, a key on the Ko, or some have a stain on the pavement you waiting/tap/double tap/etc. to toggle the pad.

  If not, you could try to go on the site of HP and DOWNLOAD/reinstall assistance the SW for the touch pad.

• FN + F3 disable the Touchpad does not work. Dell XPS L702X

  Hello, I am new to this forum.

  The function FN + F3 that disable the Touchpad does not work, my laptop Dell XPS 17 (L702X)

  I googled my problem and the only thing I found was this: http://en.community.dell.com/support-forums/laptop/f/3518/t/19454265.aspx

  I think that my problems with the touchpad started when I plugged a mouse into the USB port. It didn't work (it worked well before), and in material-sound-mouse control panel, the system asked me to uninstall a driver or other. I do not remember, but later the mouse worked.

  After this weird thing with the mouse, I noticed that the touchpad was malfunctioning. While I write, the cursor moves without touching the touchpad, it is annoying because it makes me write bad because he is moving in the middle of writing, as I write so it's a mess.

  The second oddity, the Fn + F3 does not disable the touchpad, the orange light come on (the led on the top of the touchpad), but the cursor can be moved in any case, with or without a connected mouse.

  I checked for driver updates, perform an audit of the system, checked for viruses, spywares and I don't know what I could do. I don't know if the problem with the mouse had nothing to do with the function Fn + F3 problem.

  I have not formatted or re installed windows 7, never.

  In Device Manager I have this:

  -mouse and other pointing devices:-Compatible PS/2 mouse

  Help, please. Thank you.

  DOH! Problem between Chair and keyboard...

  C:\dell\drivers\R289237

  Run the executable file of Synaptics.

  Download of extracts only the program on your disk. You must manually install the driver for the Synaptics touchpad with its own executable.

  FN + F3 now disables =)

• Lenovo IdeaPad 100-15IBD keyboard and the touchpad does not

  I bought a Lenovo IdeaPad 100-15IBD a few days ago, and after a series of problems that I managed to fix, I woke up this morning to find that my keyboard and the touchpad do not work. Last night (about 9 hours ago) it was working fine. Anyone has an idea how can I fix?

  Problem solved. It was because of the abdriver for keyboard and mouse I have installed from the official website of lenovo, I don't know how or why, but when I uninstalled it, it started working again.

• BlackBerry Z30 the touchpad does not work on my Blackberry

  Touchpad does not work after restarting my blacberry to factory settings.

  Do one or more of the following actions and try again.

  Restart: With the BlackBerry powereddevice, press and hold the power button on top about 20-30 seconds, ignore the 3-2-1 timer and hold the button until the screen goes black and you see the red LED.
  or
  Restart: With the phone smart BlackBerry turned on, using the keys of volume of the edge side, press on and hold the keys of volume for about 20 seconds and both of the Up, ignoring the initial message of screenshot... the screen go black, reboot.

• After turning on the computer, the Touchpad does not work until I have press a key on the keyboard

  Original title: Touch Pad issue

  Hello

  Every time I turn on the computer touchpad does not work (in the form of connection), first I press any key on the keyboard once I press a button and then press the mouse will start to work, I don't know what exactly is the problem... I reinstalled the drivers, checked in services but still the same. Can someone help me on this.

  Kind regards

  NGO

  Hello, NGO,

  Changes were made on the computer before the show?

  Method 1:

  Run the hardware and devices Troubleshooter and check if that helps.

  Method 2:

  I suggest you to return the item and check if it helps:

  Mouse, touchpad and keyboard with Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/Mouse-touchpad-and-keyboard-problems-in-Windows?T1=tab05

  Let us know if it helps.

• Satellite M105-S3031: the TouchPad does not work

  Hello guys!

  I have a M105-S3031 Satellite. It's been 1 week shut down and this morning when I turned it on, the touchpad did not work, check status, that's like "enable." I installed a mouse cable and with it works well.

  Any help?
  TKS.

  Check it please again using FN + F9 key combination.

• Satellite L350 - key FN and F9 touchpad does not work

  Hello

  I have a toshiba Satellite L350 with Vista 32 bit and my problem does NOT work FN keys.
  I installed already Synoptics Touch Pad V6.3 from Toshiba Web site, but it did not help.

  I searched for other software mentioned on this forum, but I could not find.

  The biggest problem is that my touchpad is locked, and fact without work FN + F9

  Use me keyboard just - what is difficult and annoying :(
  I'd be really greatefull if anyone can help me :(

  Hugs,
  Kate

  I agree with Akuma
  You need the PPV for the FN keys work.

  PS; If you want to use the Toshiba OS preinstalled, so everything should work properly!

• I have a Toshiba laptop and my touchpad does not work any idea on how to fix

  touchpad does not work on my laptop, it is a toshiba...

  Hello

  Some have keys that turns off the pad and many Toshiba have card keys which have a control.

  Control Panel - mouse - Touchpad is here

  Panel of configuration-device - mouse and pointing devices Manager - double click on info pilot.

  If no joy go to Toshiba Support and download the latest drivers for your version of Windows and 32 or 64-bit.

  Go here and put in your info model and search for the drivers for your system

  Download - SAVE - go to where you put them - click on - RUN AS ADMIN

  Toshiba support and drivers
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp?NAV=download

  Toshiba Support Forums
  http://laptopforums.Toshiba.com/

  Contact Toshiba
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/navShell.jsp?CF=su_contact

  =========================================

  It's my generic how updates of appropriate driver: you mainly want to update or reinstall the touchpad drivers
  and ALSO to get the Toshiba value added Package for your version IF it is there.

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - Device Manager - Display Adapter - note the brand and complete model of your
  video card - double - tab of the driver - write version information. Now click on UPdate Driver (this
  cannot do anything as MS is far behind the certification of drivers) - then do a right click - Uninstall - REBOOT
  This will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party with their
  own the software and drivers and all other main drivers that you have.

  Now go to the site of the manufacturer of system (Dell, HP, Toshiba as examples) (restoration) and then of the manufacturer of the device
  (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for the BIOS, Chipset and software)
  updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after each installation.

  Always check in the Device Manager - tab drivers version you install actually shows up. This
  because some restore drivers before the most recent is installed (particularly that audio drivers) so install a
  pilot - reboot - check that it is installed and repeat if necessary.

  Repeat to the manufacturers - BTW on device at the DO NOT RUN THEIR SCANNER - manually check by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver in the Windows updates,
  This leaves ONE of Windows updates, but it will not install the drivers who are generally older and cause
  questions. If updates offers a new driver and then hide it (right click on it) and then go look for new ones
  manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  Hope these helps.

  Rob - bicycle - Mark Twain said it is good.

• G570 keyboard and the touchpad does not work

  The new computer about 6-7 months ago. Was running Windows 7 that has settled on the laptop. I had some malware on my computer, tried many malware removal tools such as malwarebytes, adware cleaner, finally had to use system restore. Then I ran Security Check. Now, I can't start in safe mode or in normal mode. When I turn on the computer, he'll go as far as the login screen and then does not allow me to move the cursor or type my password. It behaves as if the keyboard and touchpad are locked. I have to remove battery to shut down the computer. Same problem reappears when I turn it on again.

  Hi reeder2,

  What you read is correct. After hitting the key recovery key, fall into place the machine and directly to the recovery menu.

  Do try and let me know.

  Concerning

• PC laptop HP 14r008-tx: Hello, I have a question, I just reset my laptop and my click on tapping the touchpad does not work

  What should I do to make the click on touchpad work look once again?

  Strange. The driver list appears for me. Even foreign - it lists the Synatics and Alps Touchpad drivers. Can you confirm that you have?

  Try one of these direct download links that you have.

  Synaptics:

  http://ftp.HP.com/pub/SoftPaq/sp72001-72500/sp72088.exe

  Alps:

  http://ftp.HP.com/pub/SoftPaq/sp72001-72500/sp72284.exe

• Right button on the touchpad does not and cannot change the setting of what happens when the laptop is closed

  I own a HP Pavilion, under Windows Vista Home Premium, with 2-way ALPS Touchpad, I updated the touchpad driver and tried to change the options of the right button but nothing has helped.    Also, how can I change the settings for when I close my lap top

  Try the right key when it is started in safe mode or with a clean bootor maybe when logged in as a different user.

  Change the cover closing the settings by going to control panel-> Power Options-> choose closing the cover.

• Satellite C50D-B-120 - buttons on the touchpad does not work after upgrade to win 10

  I just bought this new laptop. I have updated to Windows 8 Windows 10. Everything worked fine before the update. I am now active on Windows 10 and the mouse pad does not work. Initially, the entire mouse pad not working, I couldn't even move the mouse on the screen. I had a play around in the settings and have managed to get the work of the mouse, but now the button of mosuepad. I searched around the computer for the settings to solve this problem, but I had no luck.

  Please any help would be great, begin teaching and could do with getting this issue sorted.

  Thank you!

  You need to uninstall the driver for the touchpad (MOMENTUM or Synaptics)
  After that, restart the laptop...

  You can also try to update the driver in Device Manager... but the unit must be connected to the internet...