(Redirect) Error 2000 - 0146

Similar Questions

• 2000-0146 repair manual of hw

  Hello

  If my HARD drive has failed. Diagnostic error 2000-0146. I know it is recommended to replace the hard disk immediately, which I do, but I have a few unback-increased data I want to recover.

  So far, any approach to software has failed. I can't boot from the drive and even boot from another disk with the defective one connected as slave wont do good. I managed to connect the drive via external media via USB, but I only see the 100 MB system partition. The main data partition of 698, 54 GB is detected, but it is listed as filesystem RAW., and as I discovered during some tests desperate thereafter, it cannot be formatted.

  I tried to recover the data using Zero Assumption Recovery, which has detected that the entire partition is filled with bad sectors. I know that areas are not damaged, and the electronics of the drive that prevent access to them.

  I also tried other tools of recovery, but without success. I gave up to fix this on the software layer, but if someone has a new approach to software I'm open to ideas.

  My question is: is it possible to recover the data by replacing electronics (chip-Board on the underside of the disc) with the same, but a whole new drive? I know that there may be a problem on some other place, but given the circumstances, there is still a small chance that it would work? I am concerned about some failure stops that would prevent construction drive/chips with they were not manufactured with parts.

  Thank you all for the thoughts,

  Tesarst2.

  Based on the ability (I guess 750Go) this player has 100% flexible single read/write on the circuit board.  If you throw this PCB trash you throw your data with it.    Make SURE not not to lose.

  If you want your things back to send to Gillware, Dell data recovery provider.  Be SURE to send the original PCB!    Search for 'data recovery' to dell.com to get referred to Gillware or call us at the 877-624-7206.

  If it detects in BIOS, they can get it back.

• Drive HARD 2000-0146, windows Security Center does not, all downloads have refused as containing viruses. PDF answer either.

  His Dell Inspiron 1464, purchased in 2010.

  * HDD error 2000-0146, how to fix it.

  * Eset Nod32 does not and has not been allowed to work properly.it has no web access protection.

  * IE does not open any website and emails, downloading is permitted as States contain viruses.

  * Currently eset nod 32 is not installed on my laptop.

  the problem is not too big and small, that I updated all drivers and scanned a month ago to remove all viruses etc.

  But I can't find a way to fix above error to avoid a reinstallation.

  * I updated my BIOS and it sees SATA.

  * PC diagnostic shows no errors of any kind.

  * has tried all the win-fix-it.

  Thank you.

  I was looking for something for you in the Forums and finally found.

  Read the answer by The ball

  "I get the error message"xxxxx.xxx"contains a virus and has been eliminated ' downloads... on all software updates from microsoft.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-security/i-get-error-message-xxxxxxxx-contains-a-virus-and/fbb5e0fd-63bd-4E01-9a98-6074d33a8fd6

  See you soon.

  p.s. with RKill, there are a few other names available for download of RKill attempt to deceive malware.

• Error code: 2000-0146 (laptop hung on "Installation screen Windows updates")

  OK, so I have every time I turn on my computer dell laptop (I have windows vista) it acts like it is to install the updates of windows. He said same facility 3/3 even though the completion bar shows 0%. She does this, is like its about to restart then passes to the installation screen.  I ran the diagnostic test and the error code 2000-0146 came. I'm not sure if this is useful, but if anyone has a solution please help! Thank you

  Oh and I tried to restore the option and he did nothing.

  Hi cgardne5,
   
  1. How did you restore the computer?
   
  Try these steps and check the result.
  Step 1: The repair of the boot with Vista DVD
  a. Insert the Windows DVD.
  b. restart your computer.
  c. let the computer restart (boot) from the DVD.
  d. If you are prompted, press a key to continue.
  e. When you reach the screen install Windows, select your preferences in the language to install, time and currency format and keyboard or input method boxes, and then click Next.
  f. do not click install now. Instead, click on repair your computer. The System Recovery Options dialog box appears.
  g. make sure that the appropriate operating system is selected, and then click Next.
  h. After you click Next, the System Recovery Options menu appears.
  i. click on startup repair. Once the Startup Repair tool is completed, click Finish to restart the computer.
  j. remove the DVD and restart the computer to see if the system boots fine.
   
  See Repairs to the system of Windows recovery environment
  Step 2: If you do not have the Vista DVD, start the computer in safe mode and restore the computer
  See Start your computer in safe mode
  See System Restore
  NOTE: You can also choose the system restore on the system recovery options.
   
  Kind regards
  Syed - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error code 2000-0146

  Hello

  I get the error code 2000-0146 found no operating system, I'm on Windows Vista on a Dell inspiron 1545.

  Tried to boot from the CD I can do a disk check but it go than even if loading step and then the green light flowing (as knight rider because..... kit) while he just sits on a gray screen... Any ideas anyone... youn think it's disk hard totally kaput, or maybe something else... I read on the site that someone changed its ram as 1 was defective and it worked.

  Thanks in advance

  Chris.

  Saving your files:

  You can remove the hard drive and put it in a hard drive USB enclosure > plug it into another computer > and try to read and copy your data in this way.

  @@@@@@@@@@@@@@@@@@@@

  This program may also interest you.

  "TestDisk, data recovery.

  http://www.CGSecurity.org/wiki/TestDisk

  TestDisk can run under

  • BACK (either real or Windows 9 x box BACK),
  • Windows (NT4, 2000, XP, 2003, Vista, 2008, Windows 7 (x 86 & x 64) Windows, 10)

  @@@@@@@@@@@@@@@@@@@@

  Or, you can download Knoppix > make a bootdisk to > start your system with it (IF your material is all work) > and copy your data from the hard drive like that.

  http://Knoppix.NET/

  "How to use Knoppix.

  http://Lifehacker.com/192982/geek-to-live--rescue-files-with-a-boot-CD

  @@@@@@@@@@@@@@@@@@@@

  "Recover files from Windows using Puppy Linux disks"

  https://www.WinHelp.us/recover-files-using-Puppy-Linux.html

  See you soon.

• Error code 2000-0146 and 0F00:065 D and B 0F00:137

  I have a Dell Studio 1735 laptop.  Today it froze on me.  I could only make a hard stop.  I tried to log in again and got on the desktop with icons, but couldn't go further.  Don't have hard stop yet and I tried to go back to the top.  I made a kind of diagnostic tests and received the error code 2000-0146 following.  Also received the 0F00:065 D error reading DISK_0-self-test and 0F00:137 B DVDRW_1-disk is missing Virgin insert the data disc (example of the RCD).  I don't know what all these means.  Can someone direct me if it can be repaired and how I can fix it.  Or do I need a new hard drive.  Your help is greatly appreciated.  I use another laptop to write this message.

  The first two messages mean that the hard drive has failed. The third says there is no disc in the DVD drive, so it could not be tested.

• Error code 2000-0146, 0141

  2000-0146, 2000-0141 error code.  He cannot get the computer to go to safe mode. Computer turns on, dell appears and then darkens.  Any help is greatly appreciated.

  When I turn on the computer, I can go to F2 or F12.  When I hit F8 a list appears, but any item I select the screen goes black and then after 2-3 minutes it says failed to start.  Try F1 to reboot, F2, to go to the configuration and F5 to run Diagnostics.  If you run them diagnoses get error codes.

  These are mistakes of automatic drive test. You will probably need to replace the hard drive.

  http://support.Dell.com/support/topics/global.aspx/support/KCS/document?c=us&CS=19&l=en&s=DHS&docid=DSN_126A722713F6D0D0E0401E0A55174AE6&isLegacy=true

• Received error BSOD, ran Diagnostics, got the error code 2000-0146, tried to boot from different HARD drive, got the same stop error message

  So my friend gave me his computer dell laptop. The thing would boot normally for a few days until he would give me a blue screen of death with the "UNMOUNTABLE_BOOT_VOLUME" message constantly to not even upward. I ran the diagnostics and got the error code 2000-0146. What I've read, this code error means that the HARD drive is bad and must be replaced. So, to make sure that it's the hard drive, tried to boot from an old hard drive, I got around the installation by USB and windows gave me the same stop error message. May - so that means it's a motherboard problem?

  No, it isn't - unless the operating system was installed on this drive AND the system in question, that it won't work as a bootable drive.

  Unplug the system, remove or disconnect the battery and hold the power for 30 seconds approximately.  Turn on and re-run the diagnostic tests - if the same error appears again, the drive is bad.  Replace it.

• I get an error code 0146 and or the image of exe.bad the logon user interface

  I can't reboot my computer, I keep the error code and get or bad image. I have almost everything and I keep getting the black screen reads LogonUIexe.bad image and when I do the test I get an error code 2000 - 0146.help.

  Hello

  I suggest you to follow these steps and check if that helps.

  Method 1:

  Try to start the computer in safe mode and check if the same problem occurs:
  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Method 2:

  Try to perform the verification and startup repair if it helps:

  http://Windows.Microsoft.com/en-us/Windows-Vista/startup-repair-frequently-asked-questions

  It will be useful.

• Windows 7 - after selecting a USER, the computer opens the selection screen of the USER - code throws again: 2000-0146 to diagnosis

  Computer seems to boot correctly.  Once a USER is selected in the USER SELECTION screen, the computer seems to proceed... but then the USER SELECTION screen opens again.  When you run the Diagnostic tests, the only error is 2000-0146

  Hello

  Thanks for posting your question on the Microsoft forums.

  I understand that you have a problem on your Windows 7 computer. I would certainly help with this question.

  This problem started after the recent update installation of Windows?

  Some members of our community have reported similar problems after the recent update of Windows KB3097877 installation on

  their Windows 7-based computer. The update has been re-released, uninstall and reinstall the update can help us get this problem is resolved.

  In order to solve the problem, I suggest you try the steps posted by Akil P responded on November 13, 2015 in the following thread and check if the steps help you to solve the problem.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-update/flickering-screen-and-sign-in-problems-on-Windows/df9c8255-587f-4DBF-BB45-6639b29dc4ae?TM=1447375680761

  Hope this information is useful. Let us know if you need additional assistance, we will be happy to help you. ___

  _____________________

  Thank you best regards &,.

  Isha Soni

• Receive the error code 0146 in Vista

  From what I understand that it is a hardware problem, I have some see reinstalled vista.

  If I re - install, willl, I end up having the same problem again?

  Thank you

  http://www.google.com.au/search?hl=en&source=HP&q=error+code+0146&aq=f&aqi=G6G-M4&AQL=&OQ=&gs_rfai=

  Read the info above from Google about it.

  All this points to hard disk problems.

  See you soon.

  Mick Murphy - Microsoft partner

• boot error 2000-0141

  I have a dimension xps 420. 3-4 months. It worked perfectly until this morning. yesterday, I installed a game that went very well. but the computer is restarted apparently a drive could not be found and the error code 2000-0141 appeared. Ive has diagnose repeatedly to no gain. I don't know what I have to do.

  The message that is displayed is as follows:

  . Drive 0 not found: Serial ATA, SATA-0

  Alert cannot detect one or several drives during POST.

  Hit the F1 key to continue. F2 to run the Setup program.

  Press F5 to run onboard diagnostics.

  F1 is simply the message repeats. using f2, boot sequence displays 5/6 discs labeled (absent). F5 eventually give me the error code 2000-0141

  Help please!

  Hello, I'm going now you have posted this 6 years, don't know if you'll ever find my message, but in case you do, please, if you can, let me know the alternative link to the solution of the error 2000-0141, the link to the KB document is not here, but most probably it was deleted? I hope not!

  Thank you very much!!!

  DivFil

• 2000-0146 raid 1

  Initially get 2000-0142, not the OS starting and stopping at mup.sys when starting in safe mode.  Copied into the original registry files (security, by default, sam, etc.) to retrieve the BONES, but now the keyboard and mouse are not active while in the operating system (the computer makes noise "dee-dunk" when they are connected and removed) and receiver 2000-0146 from diagnosis.

  It is a Dell Precision T3400 (downgraded from Vista to XP) with a Raid 1, so I think that if it is a hard drive problem, it would still be a good hard left.  Mouse and keyboard work fine in diagnosis and in the recovery console.  Have tried both USB than PS2 for the mouse and keyboard.

  Make a back-up and reinstalled (instead of repair) Windows on a drive.  The first warning was about to lose all the data, but there are options on the maintenance of the windows partition, OS works, and a .dll not found.

• Error code 0146 - trying to retrieve files

  So I understand that if I have the error code 0146 that my hard drive is toast.  However, is it possible for me to get some of my files from the hard drive?

  
  

• Hard drive failure: error 2000-0142 since current default Scan PC.

  Original title: error 2000 - 0142

  Activities of PC by default Scan on my laptop DELL Inspiron 5520. Hard drive failure: 2000-0142 error what does that mean?

  REDA

  According to the answer by a representative of Dell here:

  http://en.community.Dell.com/support-forums/laptop/f/3518/p/19467468/20188938.aspx

  It seems that the error means what it says - the hard drive has gone bad and should be replaced.

  I highly recommend that you only backup your data to another drive immediately and then contact Dell for confirmation about the error and advice on the best course of action.