(Redirected) Power adapter green light turns off when the laptop battery is plugged into the laptop and does not load.

Power adapter green light turns off when the laptop battery is plugged into the laptop and will not charge; If the laptop battery is not plugged into the laptop adapter it's still green and will charge the laptop.

As you have a laptop, better make this laptop in the computer Forum post here:

http://en.community.Dell.com/support-forums/laptop/default.aspx

Tip: when you post a message, preferable to always include the computer model.

Bev.

Tags: Dell Products

Similar Questions

  • Computer turns Off at the start and can not reinstall windows

    Hello, I'm Paul and I * generally * use my mac. At the point where I need my Windows laptop, I can't use! I recently had Windows reinstalled, and after some time, he asked to * automatically install a driver *. Well, which brought an end to the life of my computer. It was the 12' th reinstalling windows. now when it starts, it just turns off. I tried to insert my CD of Windows Vista, but guess what? It says "Windows loading files...". ", and then it shows this screen of Microsoft Corporation loading with the bar and the bars green bit into it. After a little while ago, my computer just turned off! How the _ am I supposed to reinstall Windows (well, actually, install Ubuntu ^. ^) now? I tried it, but:------all else fails.

    Please HELP, it's so sad. I will not buy another Windows computer.

    ~ Paul Côté

    For any problem with reinstall Vista from recovery of the manufacturer support, contact the manufacturer of your laptop.

    This isn't their recovery process, Microsoft

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    To reinstall from a Microsoft Vista DVD:

    Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

    At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

    http://support.Microsoft.com/default.aspx/KB/918884

    MS advice on the conduct of clean install.

    http://www.theeldergeekvista.com/vista_clean_installation.htm

    A tutorial on the use of a clean install

    http://www.winsupersite.com/showcase/winvista_install_03.asp

    Super Guide Windows Vista Installation

    After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    To install Ubuntu:

    http://UbuntuForums.org/

    See you soon.

    Mick Murphy - Microsoft partner

  • My MacBook Air will not power cover apple "is turned on but the button / stop does not work

    Attempt to power up/down does not. Badge of 'Apple' external 'cover' lights up; keyboard is not backlit. Slightly warm base. What should I do?

    Press and hold power for more than 10 seconds and the MBA should turn off.

    Try a SMC reset:

    https://support.Apple.com/en-us/HT201295

    Ciao.

  • I had to do are install disks initially provided. My computer turns off during the process and did not finish. Info please.

    I had to do a re system install the OEM disks but my computer starts to spin off before the reinstall is complete. As my dischas been reformatted I can't access control panel to reset the timeout settings. Advice please.

    Hello

    You tell us why you had to reinstall.

    If it keeps closing, it looks like you have a hardware problem.

    The OEM recovery disks are provided by your computer manufacturer.

    For problems with their recovery process, you will need to contact them.

    See you soon.

  • How to upgrade Vista to Win 7, when the upgrade wizard does not load in the Windows Anytime Upgrade window.

    How to upgrade Vista to Win 7, when nothing is loading in the Windows Anytime Upgrade window.

    After the purchase of a new license to upgrade from Vista to Windows 7, after the opening of any time upgrade window, nothing happens. He sends you open app Windows Anytime Upgrade and it suppose to open the wizard to enter the new product key, but Wizard does not open, and there is no option under app anytime upgrade win to open the wizard. There was no link to download the upgrade, follow the instructions to upgrade through win app anytime upgrade.

    The Windows Anytime Upgrade was not designed to be upgraded to Windows 7.  It can only upgrade from one edition of Windows Vista to another edition of Windows Vista.  In order to upgrade to Windows 7, you must follow the upgrade procedure described here: upgrade Windows Vista to Windows 7

  • Power problems: computer turns off when the power supply cord is unplugged.

    original title: power problems: computer shit turned off when the power supply cord is unplugged.

    I have a HP Pavilion dv2000

    Windows vista home premium/sp2

    AMD Turion (TM) 64/2 1.80 ghz processor

    1 GB memory

    32 bit operating system

    I have 2 problems with this laptop.

    !. I have lost the power cable and bought an expensive one online step (model: PA-1650-02 c. input 100-240v 1.5 put out a(1,5A) 18.5V 3. 5 = a)

    When I first plugg cord battery charge light came on the balance, then he started to come on and outside.

    now its completely off, even with the power cord plugged in. on the lower right part of the screen its showing that cord is connected to the power supply and the battery is fully charged, but as soon as I unplugg the power cord or remove the computer cut right away.

    the second problem is that the left mouse botton does not work, the work aside right very well. I went in the proprties to put it right, click on to, but who does not work either. I've updated the drivers but still nothing.

    Any help will be greatly appreciated.

    Hi aloum,.

    (a) what kind of mouse you are using?

    (b) the left button of the mouse seems to be stuck or it does not meet the click? This only happens with certain applications?

    Step 1: Test the mouse on another computer or another mouse on the test computer

    To determine whether the mouse or the computer is defective, follow these steps:

    1. test the mouse in question on a system that works, you know. If the problem appears to follow the mouse, you may need to return or replace the mouse.

    2 test a mouse you know is working on the computer in question. If the problem seems to stay on the computer, then the problem is most likely related to the software.

    In regard to the battery not holding charge

    Battery problems are often associated with the battery itself. If you encounter this problem, contact your mobile PC manufacturer. If you purchased the battery separately from the notebook computer, contact the manufacturer of the battery.

    Troubleshooting battery problems

    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-battery-problems

    Thank you, and in what concerns:

    Ajay K

    Microsoft Answers Support Engineer

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • The screen of my laptop turns off when the power cable is connected. If this isn't the case, connected screen is ok. No idea why?

    The screen of my laptop turns off when the power cable is connected. If this isn't the case, connected screen is ok. No idea why?

    Original title: clear the display

    Click Start or press the Windows key and type power can locate the power to change recording settings in the section of the Control Panel from the list above and click on it. At the opening of the Power Options pane, click choose when turn off display available on the left side.

    Choose a new setting for brightness in the drop down menu on the battery . Look at all the other parameters that you feel you want to modify, and then click save changes in the lower right to apply the options you have selected energy saving.

    You can now close the Power Options pane when you return.

  • printer do not wake off mode 'sleep' and does not turn off when the Start button / stop pressed or pushed.

    HP printer all-in-one B210a win 7 64 bit.

    no error message just don't wake up from power saving mode and does not turn off when the power button is pressed. must be disconnected and then turned back on. works fine until the power saving mode he did go to sleep then not answer the test print command or Toolbox controls.  power saving mode is turned off, but still goes to sleep.

    First, you will need to make sure that the printer is under warranty.  You can do it here.  So, if you are in warranty, you must contact HP at 1-800-474-6836 and the United States in computer science, international users click here.

  • Accelerometer turns off when the screen is off

    When testing my application on a Z10 android port the accelerometer turns off when the screen is off. A partial wake lock does not turn the sensor back on. A wake dim screen lock is needed to re - turn on the detector. This behavior forces the screen to be all the time when an application requires the use of these sensors.

    An example would be a pedometer recording the steps throughout the day. In order to operate the screen must be turned on by the application that runs in the background. This will cause a fast draining of the battery and is not an acceptable solution.

    On Android, a partial wake lock is enough to keep the accelerometer running.

    I think this should be reported as a deficiency, a lot of motion carried since Android applications will be blocked by this and my app port is one of them.

    Tested on system Z10, model number STL100-3. Version of the 10.1.0.273 software

    The fix will appear in MR 10.2, 10.2.1 aka.

    I recently submitted a fix for the problem.

  • computer won't goto sleep IE screen turns off but the hard drives will not be

    No matter what I put in power options, the computer won't go to sleep.

    The monitor turns off but the hard drives, fan to continue working.

    I can't force the drives to put beyond the control of the characteristics to uncheck in the power options.

    The computer turns off when the power off but sleep option does not work.

    Thanks for any help.

    Hello

    Thanks for posting your question on the Microsoft community.

    I would like to know some information about the problem so that we can help you better.

    What is the brand and model of your computer?

    Thank you for details on the question and your efforts to resolve.

    This problem may be due to the following reasons:

    -The drivers are not updated.
    -Power option settings are incorrect.
    -The devices connected to the computer are preventing it from going into standby mode.

    I would suggest trying the following methods and check if it helps.

    Method 1:
    Run Troubleshooter of power and control.
    Reference:
    Open the troubleshooter of power
    http://Windows.Microsoft.com/en-us/Windows7/open-the-power-Troubleshooter

    If this does not help, use method 2.

    Method 2:
    Please use the suggestions in this article and check the issue.
    Reference:
    Windows 7 is not going to sleep
    https://Support2.Microsoft.com/kb/976877

    I hope this information helps.

    Please let us know if you need more help.

    Thank you

  • IPhone 6 continues to go to the turning off of the screen and the screen where I enter my access code.

    IPhone 6 continues to go to the turning off of the screen and the screen where I enter my access code to return. I hit Cancel on the stop screen or type my password the password screen and it goes back to the screen, I was on. I did a reset, all settings, but not him erase all content and settings. I went all day without any problems and an ago he started to panic. I took the cover of a few days ago thinking it might be the cause of the problem by pressing the power button, that wasn't the problem. Can someone give me some advice on what could be the problem?

    I have not updated my phone to the new IOS

  • Windows Defender: I think that I accidentally turned off Windows Defender by using Windows Defender. Now, Windows Defender does not start

    I think I accidentally turned off Windows Defender by using Windows Defender.  Now, Windows Defender does not start.  How can I get this start?

    http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Defender-on-or-off

    Turn Windows Defender on or off the information on the link above of Microsoft.

    And also read this:

    If you have Microsoft Security Essentials, AVG, McAfee, Norton, etc. installed, they have a conflict with Windows Defender, or turn it off.

    Microsoft Security Essentials has its own integrated version of the defender and it automatically disables the version of Vista in Windows Defender.

    See you soon.

    Mick Murphy - Microsoft partner

  • After that installation of 9.3 iPad will not activate, it has been restored, but still not turn on. The first owner does not know the password

    After that installation of 9.3 iPad will not activate, it has been restored, but still not turn on. The first owner does not know the password

    And this is not recognitze by any device, computer or iPhone 6plus.

    If you or the original owner did not have the password no one here or at Apple can help you.

  • can not be run Zoo Tycoon, when the running game does not appear anything, help me! my computer is Win7

    original title: subject zootycoon
    my computer can not be run Zoo Tycoon, when the running game does not appear anything, help me! my computer is Win7

    Hello

    1. what version of Zoo tycoon you play?

    2. is it works much earlier?

    I suggest to run the game as administrator and check.

    I suggest you to follow the steps from the links and check out.

    Improve the performance of your computer game

    http://support.Microsoft.com/kb/815069

    The problems of the game performance

    http://Windows.Microsoft.com/en-us/Windows7/fixing-game-performance-problems

  • How you uninstall photoshop elements 13 when the windows uninstaller does not work?

    How you uninstall photoshop elements 13 when the windows uninstaller does not work?

    Hi James,

    You can follow the article: use the Adobe Creative Cloud cleaning tool to solve installation problems and use Adobe Cleaner tool that helps you to uninstall the application.

    Let us know if it works or not.

    Thank you

    Yann Arora

Maybe you are looking for