Reference Dell 2824 / Ubiquiti UniFI / label Guest WIFI VLAN
Hello
I have a PowerConnect 2824 and two Ubiquiti UniFI APs which each is connected to a port on the 2824.
UniFi access points create wireless networks and share among all radio configuration. These two APs publish two SSID, a protégé of personnel, another network wireless wireless network not protected for the guests. I have the ability to mark every wireless network that I want to.
I want to use a VLAN to push traffic via the Dell switch on a DMZ port in our firewall.
My original idea was to:
1 tag the comments with 11 wireless network VLAN.
2. let the unlabeled personal wireless network.
3. set the trunks on the two ports that puts an end to the APs to allow marked and 11.
4. Add an additional port on the 2824 11 membership only.
5 connect the 11 only port to port my firewall DMZ.
Here are my questions:
1. a trunk port enable both unlabeled and package ID?
2. If so, can I specify a port DROP packets not marked? (I want to prevent things not tagged to reach the DMZ port on the firewall).
3 - does anyone see a flaw in my game to the top?
Thank you
m
Yes, they should be able to achieve anything on the vlan 1. The personal wireless packets should come in unmarked and vlan 1 being without a label, that is where the packages will remain.
2 comments wireless packages will come in VLAN tagged on 11 and be able to access what in the VLAN 11, g16, could probably leave g16 tagged VLAN 11 If your firewall can read tags VLAN
Your installer should work fine. VLAN 11 only have access to the dmz on the firewall port.
Tags: Dell Switches
Similar Questions
-
Reference Dell 6248P - Guest Wifi VLAN config
I am trying to retrieve all upward of a VLAN. The VLAN is comments wireless traffic going through our main switches and on an ADSL router but I'm running into some difficulties.
We have 3 points of access for model AP - AC Unifi. Each access point has a connection of physical network of 1 of 4 Dell 6248 switches which are currently in a single stack managed as follows.
AP 1-> Port of the Switch 1 40
AP 2-> Port of the Switch 2 36
AP 3-> Port of the Switch 3 17
The managed pile and AP are currently using the 192.168.1.0/24 on VLAN 1 - default and I created a VLAN 10 - guest.
The APs have two SSID WLAN, 'corporate', which is also on the 192.168.1.0/24 range and 'guest' that is located on 192.168.99.0/24. I put the "guest" to mark its traffic with VLAN 10 and no DHCP is defined.
I put the 3 above general Mode ports, allowing all managers and VLAN - 1 that are not marked and VLAN - 10 they are labeled.
I also put a Zyxell router with a static address of 192.168.99.254 in Switch 4 Port 24 and set the access mode for VLAN 10.
The router is configured to provide DHCP for the beach of 192.168.99.0/24.
Now when I connect a laptop to our 'coporate' WLAN, everything works fine. I get a DHCP address from our server and I can reach everything as usual.
When I connect to the "guest" WLAN, I do not receive a DHCP address, in addition, I am able to ping on subnet 1 hardware VLAN I thought would not be possible.
Can someone take a look at this config and I would like to know what is the problem with him?
! Current configuration:
! Description of the system «PowerConnect 6248P, 3.3.12.1, VxWorks 6.5»
! 3.3.12.1 system software version
! Passage mode is configured as disabled
!
Configure
database of VLAN
VLAN 10
VLAN 10 1 routing
subnet of VLAN association 192.168.99.0 255.255.255.0 10
output
unicast SNTP client enable
192.168.1.18 SNTP server
battery
1 5 Member
2 5 Member
3-5 Member
4-5 Member
output
switch priority 1 12
IP 192.168.1.212 255.255.255.0
default IP gateway - 192.168.1.227
IP - my.domain domain name
name of the IP-server 192.168.1.18
name of the IP-server 192.168.1.19
name of the IP-server 192.168.140.2
IP routing
IP route 192.168.99.0 255.255.255.0 192.168.99.254
interface vlan 10
name of the "Guest".
Routing
IP 192.168.99.212 255.255.255.0
bandwidth 10000
IP helper-address 192.168.99.254 dhcp
IP mtu 1500
output
level of a8e64cdc85228f4c837da747958ffd74 user name 'admin' password encrypted 15
l2relay DHCP
DHCP l2relay vlan 2.10
!
interface ethernet 1/g7
Auto mode channel-group 2
output
!
interface ethernet 1/g8
Auto mode channel-group 1
output
!
interface ethernet 1/g40
switchport mode general
switchport general allowed vlan add 10 tag
output
!
interface ethernet 2/g36
switchport mode general
switchport general allowed vlan add 10 tag
output
!
interface ethernet 3/g2
Auto mode channel-group 2
output
!
interface ethernet 3/g17
switchport mode general
switchport general allowed vlan add 10 tag
output
!
interface ethernet 3/g48
Auto mode channel-group 1
output
!
interface ethernet 4/g24
switchport access vlan 10
output
outputI was looking back through the configuration, and on the 24 port setting, I see there is a command to access in place, but the port is not set to enter the mode. Can you try to put the port in access mode?
interface ethernet 4/g24
switchport mode accessDuring the test with the laptop plugged on the switch, we should test it first with a static IP address. This is to ensure that we have a connection established. Then you can move on to DHCP.
The router will appear in the output of one of these two commands?
console switch arp #show
#show bridge console table address
-
Reference Dell R710 always detected memory guest VM in 95%
Dear Guys,
I have a R710 with 2 CPU intel 5506, 8 GB of memory. I installed several Windows VM inside. I found that the always detected ESXi host all windows use plus 95% memory and I got the alert or a warning. When I checked the windows, just using less memory of only 50%.
I also have an another 2850 and installed the ESXi and there do not have this problem.
Y at - it suggestions to solve this problem?
Thank you very much.
Lewis
-
Reference Dell upgrade package cannot install the dell wifi driver
Hello
Since I reinstalled Window8 in my inspiron 3138, the laptop can not install the upgrade package from dell"and can not install my wifi driver.
I can not install the following drivers and the laptop cannot detect WiFi at all.
1704 Wirelss Dell Wifi driver (Network_driver_342TP_WN32_7.35.333.0_A01)
Driver for the mod aircraft Dell (Network_driver_PX8MM_WN64_1.0.0_A00) switching
Do you know how to solve this problem?
Best,
Lucy
Please let me know which operating system you currently have on the computer. It's 10 or windows 8.1. Because the version you are trying to install is for windows 10. Also please go to Device Manager and confirm the card this wireless network adapter option.
-
Trouble connecting Netgear XS748T to Ubiquiti UniFi US-48-750W via Port SFP +.
We bought a new switch Netgear XS748T and try connecting to our existing network which consists of several switches of Ubiquiti UniFi US-48-750W, and we try to connect using the SFP + 10 GB ports on the two switches. We have a Direct Link SFP + SFP + DAC, passive, 1 m, cable AWG30, we bought at Amazon / 10Gtek and when we try to use this cable between the Ubiquiti switch and the Netgear we get no link activity.
However if we use the same cable between two of Ubiquiti switches it lights immediately and works very well, the same is true if we use the same SFP + cable between the switch Netgear XS748T and a XS728T that we must also. Its almost as if the switches detect the same manufacturer at the other end and right link up but when its manufacturer another pass on the other end, it does nothing.
It is very aggravating, and Im going to be obliged to return the new Netgear switches. Can someone make a suggestion or confirm if they should or may not work? Everything simply connecting switches together using a cable of copper works very well but since our current switches don't support 1 GB via copper it provides not enough bandwidth for our use so we really need the port SFP + 10 GB to give us the uplink.
Here is a link to the modules SFP + cable, we bought:
https://www.Amazon.com/DP/B01LSGGUOY/ref=twister_B01M0ER4M0?_encoding=UTF8&PSC=1
It seems that I solved the problem myself. I bought a set of:
10Gtek for Cisco SFP - 10 G - LR, 10 Gb/s Transceiver SFP + module 1310nm 10kmAnd the LR version worked instantly. I honestly don't know what's the difference between a SFP + SR module and a module LR SFP +, but for some reason any LR module has allowed these two switches to connect.
Here are links to the modules and the cable used in case anyone needs a solution to this:
LR SFP + Module:
https://www.Amazon.com/GP/product/B00UMS905G/ref=oh_aui_detailpage_o00_s00?ie=UTF8&PSC=1Fiber cable:
https://www.Amazon.com/GP/product/B00T5796DQ/ref=oh_aui_detailpage_o00_s00?ie=UTF8&PSC=1 -
Reference Dell 1700 crashed and I have no backup
Reference Dell 1700 crashed without backup whats a girl to do
lost all programs can run does not help
Reference Dell 1700 crashed without backup whats a girl to do
lost all programs can run does not help
Reinstall Wndows.
Reinstall all your programs from the original media or downloaded files you have saved on an external drive.
Reinstall all your data from the backups that you made on an external drive.
If you have not, you're out of luck.
-
Reference Dell vostro 1520 with windows xp prof... Not reading CD/DVD
Reference Dell vostro 1520 with windows xp prof... Unable to read & play any cd/dvd.tried mr.fixit content but no solution at the moment.
Hello
1 have. what fixit you tried?
2. don't you make changes to the computer before the show?Your CD or DVD drive is missing or is not recognized by Windows or other programs
http://support.Microsoft.com/kb/982116Important: To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/) how to back up and restore the registry in the window.
-
Original title: unable to print. Reference Dell 944 communication usb port is not available.
Message says 'check your firewall settings to ensure the printer communication is not blocked. Printer has worked faithfully until the problems started with the XP Home operating system. To cut a long story short ram upgraded to 2 GB, all unnecessary programs identified and technician Microsoft contacted to solve problems. I was informed of problems caused by 3rd software party conflicts. Kaspersky was apparently the culpit. Dell Inspiron 32 now much faster but the printer will not work little matter what I do. I tried to reload with drivers & utility CD, drivers uninstalled & reinstalled on the site of all nothing is? Can someone help?
DavidNicholsonXN,
How to download and install drivers in the correct order
also try to read...
The owners of all-in-one printer Dell 944 thread (W7)
Let the printer after Kaspersky
Rick
-
Reference Dell pc with xp family. Restart to the logon screen
Reference Dell pc with xp family. Restart to the logon screen. starts ok in safe mode. run msconfig and do that no change then do restart ok everything ok until the cold start, then hand it to restart?
Peek into the registry to find clues.
Disable the automatic restart in case of system error and see if you can capture a message of error checking bug (BSOD) with useful information. Automatic restart in the event of system failure can be disabled in the F8 advanced boot menu, or you can turn it off in system properties.
1. right click on my computer and select Properties.
2 - Click on the Advanced tab, and then click on the Start button and recovery settings.
3 clear the automatically restart box and OK your way out system properties.Start the computer in a Clean Boot State, if the computer starts successfully in a clean boot state, then one of your user programs most likely problems, look in the case of journal of indexes.
How to configure Windows XP to start in a "clean boot" State
John -
Reference Dell M1000e + aggregator MI/O port mapping
Hi all
I intend to install a new chassis Dell M1000e with Dell M/o aggregator. During the time of solution, I have a few questions about correspondences between the physical uplink with NDC blade ports ports. A Please check the config below and specify my queries?
My hardware:
- 1 x Dell M1000e
- 2 x M i/o aggregator (A1 & A2)
- 16 x M630 Blade (Qlogic 57840 S ANC four ports card)
Reference DELL M/o aggregator:
(reserved for Future use) module QSFP + 2 ports (Port No1:33 - 36 & No2:37 Port-40)
I want to use these two modules for my blades 4-port Quad and the confusion I had, how to associate these 16 ports (8 ports of each module) to the server blade and the amount of bandwidth I will get by blade with redundancy.
Module 4-port SFP + 10 GbE (Flexi-O of the Bay) (Port No.: 41-48)
Module 4-port 2/4/8 Gb FC FlexIO (Flexi Bay 1) (Port No.: 49-56)
FYI - I would like to install ESXi 6.0 on all blades
Thank you!!
Vinay
Oriented server ports are configured automatically as part of the aggregation of links groups if the server is configured for the LACP Protocol. Static GAL is not supported.
You will use the segregation network VLAN. A VLAN for network traffic and the other for the CF. Here are the commands to configure interfaces for different VLANS.
Unidentified:
Dell (conf) # tengigabit interface 0/16
Dell(conf-if-te-0/16) # vlan unidentified 4
Output Dell(conf-if-te-0/16) #.
Tag:
Dell (conf) # tengigabit interface 0/16
The tag vlan Dell(conf-if-te-0/16) # 4
Output Dell(conf-if-te-0/16) #.
Traffic from servers will follow the path of the VLAN. For example, if an internal server, facing the port is set to VLAN 4, that traffic will be transmitted on the uplink port which has also set to VLAN 4.
By default, all external ports are placed in a single whole LAG. However, you can change the configuration to support several shifts of uplink. Page 159 of guys configuration takes you step by step on setting up several shifts of uplink.
The aggregator automatically configures to match the FCoE parameters used in the switches to which it connects through its uplink ports. FIP snooping is automatically configured on an aggregator. Automatically configured port channel (LAG 128) works CWF port mode. See page 86 for more information and examples of config.
For redundancy, you could stack the units together. 241 page details the process of stacking.
Page 54 of 102 of the Guide blade IO has one other diagram that details more internal server port mapping for each blade.
-
Reference DELL T420 - battery on PERC H710 adapter controller
Hello
I received a yellow warning
Reference DELL T420 'Battery on PERC H710 adapter controller'
What it means?
What should I do?
Order the new battery?
It is a simple replacement mission?
Is it essential?
Update:
test URL
http://www.Dell.com/support/article/us/en/04/SLN130018
Have nothing, everything seems fine now...
Thank you
It is normal so he can make a full discharge of the battery as part of his learning cycle every 90 days. Make sure that this isn't that. If this isn't the case, the reason, give it 24 hours. If it is fully charged, update the system (including RAID firmware, driver first) firmware. If not fully charged yet or it reproduces quickly, then replace the battery - power down to replace.
-
Reference Dell 3110cn of Laserjet + os El Capitan
My MacBook Pro (2009) stopped my Dell printer. News on this please.
Hi deaconjo,
as I had the same problem, I found a solution for my El Capitan MacPro 2008:
Search for the following installation program:
3130cn_Installer_And_Application_Dell_A04_MAC.dmg
Inside this package you will find the driver for 10.7 and higher. After installing the package I could add an IP printer with this driver:
Reference Dell 3130cn Color Laser v3017.104 PS
With this driver installed, I can use my printer Dell 3110cn without problem.
Perhaps it might help you too.
Concerning
-
Hey guys, more of a statement than a question. If you have a Dell Sonicwall and users do "found no appropriate group" of course the same user does not exist as a local user and a domain user. This will cause problems. Took me a while to understand that >.<>
Good thought.
Thank you
Ben D
Reference Dell SonicWall
#Iwork4dell -
Reference Dell 2007FP vs HP zr22w
Hi guys, I use t410s now. You want to find an IPS monitor. Currently have two choices.
Reference Dell 2007FP (handed to nine 30-day warranty) $95
HP zr22w (new, 3-year warranty) $175
What would be a good choice?
Not for the game.
But need good color, good text, Word process, sometimes a movie.
The HP zr22w DP, is better than the VGA to connect to my T410s?
Thank you!
Your information is so helpful. But I think that I can not check the number helpfully I ordered from DELL FINANCIAL SERVICES. Thank you very much!
-
Reference Dell place 8 just out of warranty and dead now?
Hello
Everyone has a glue on Earth how to contact Dell technical support? My Tablet has acted weird for a while, but now it is completely dead and the custom lights at all. Previously, I got past pressing buttong for 10-15 minutes sometimes and then after a while it just turns itself off again. So now it's offshore and dead.
I searched web pages of Dell support for direct contacts, but not luck. And worse, that it turns out that the warranty has ended in 12/09/14
What a *.
Reference Dell of mobile devices (phones) & tablets
1-800-308-3355 24 / 7
Maybe you are looking for
-
Could not find a way to connect my Sony headphones to my TV Bravia KDL-32BX310
My TV Bravia KDL-32BX310 has "Audio In" (red and white) female connectors, but there does appear to be an 'Audio OUT', so I can't find a way to connect my new Sony headphones. (It doesn't seem to have a 'digital output'-looking on the site of the por
-
try to install itunes on pc windows 10 Dungeon error 80073715 x HRESULT:0
-
Flex 14 - Win 7 - driver "ROOT\LENOVOVHID\0000".
Hello! I got my Flex 14 to Windows 7 (64-bit). I found all the drivers except for two features: -ROOT\LENOVOVHID\0000-ROOT\LENOVOVHID\0001 Do you know what these devices are for and what I should install? Thank you!
-
Windows Live Mail sends several emails to the recipient and gets stuck in the Outbox
My windows live mail sends multiple messages for one of my email accounts (and only one). It seems stuck in the Outbox and not appear in my sent items folder, but the buyer complains to receive up to 25 times. I uninstalled norton antivirus completel
-
I try to send more than 5 pictures gat, a message saying that I have only 5 attachments
I use window live email (hotmail). Receive try to forward an email with more than 5 pictures, I get a message saying I need to delete some of the pictures because I can transmit only 5 photos (files).