Reference Dell n5010 13 beep followed by 8 beep problem

Similar Questions

• Reference Dell desktop XPS beep no boot upward

  I bought a new Dell at Costco, 2 years ago, when I press the button, it is 3 sound intermittent beeps 3 beeps burst but it does not. How can I fix it?

  Exactly what XPS? for example, 8500 XPS, XPS 8700?

  According to this, 3 beeps means:

  3	Error chipset (North and South Bridge Chipset DMA/AMT/Timer Error for Intel platform); Chipset error	System Chipset card failure
  	Time-Of-Day Clock test failure.
  	Gate A20 failure
  	Super i/o chip failure
  	Keyboard controller test failure.

  You could try clearing the BIOS:

  1. Power off, unplug, press / hold down the power button for about 15 seconds
  2. Open the case and remove the motherboard battery
  3. Power button press / hold for about 30 seconds
  4. Replace the battery (right-side-to the top)
  5. Close the case and tries to start

  Note: You can replace the motherboard with another battery while you're there. 3 volts CR2032 lithium-ion, ~ $2 at discount stores.

• Reference Dell Inspiron 660 beeps repeatedly at startup

  Hi, having a terrible problem with my 660 Inspiron I've had since June 2012

  Stop normally last time used, started at the present time, the dell screen then showed a black screen and the Office repeatedly beeps (does not stop)

  very worried, what's the problem?

  Continuous beep low and slow is bad RAM.

  Remove all the ram and see if the model changes.

  Then put 1 stick of RAM at a time to test.

• Reference Dell n5010 laptop DC Jack short-circuit/no load

  Hello guys, I was just with my laptop the other day with the charger plugged in, and then suddenly bright laptop computer charger is turned off and the perception only. (I've included a video that shows what happens when the charger is plugged). I tried to disassemble the laptop and I checked the DC Jack, but it is nice, that is nothing unusual can be seen

  I tried the charger on the other computers dell laptops and it works very well. I also tried another charger Dell on my laptop, but also, it loads the laptop, instead the same thing happens that led of the charger will turn off. I need to reconnect the power cord so that the light on again.

  I think that the problem lies in the laptop. But the laptop works fine on battery. I am also attaching a youtube link) (www.youtube.com/watch

  Hi Aparichit4evr

  Please write to us.

  By looking at the symptoms the issue seems to be with the motherboard, like the adapter light Cup once connected to the machine.

  If your machine is under warranty, we can fix it.

  Await your response.

  Concerning

• Reference Dell M1000e + aggregator MI/O port mapping

  Hi all

  I intend to install a new chassis Dell M1000e with Dell M/o aggregator. During the time of solution, I have a few questions about correspondences between the physical uplink with NDC blade ports ports. A Please check the config below and specify my queries?

  My hardware:

  • 1 x Dell M1000e
  • 2 x M i/o aggregator (A1 & A2)
  • 16 x M630 Blade (Qlogic 57840 S ANC four ports card)

  Reference DELL M/o aggregator:

  (reserved for Future use) module QSFP + 2 ports (Port No1:33 - 36 & No2:37 Port-40)

  I want to use these two modules for my blades 4-port Quad and the confusion I had, how to associate these 16 ports (8 ports of each module) to the server blade and the amount of bandwidth I will get by blade with redundancy.

  Module 4-port SFP + 10 GbE (Flexi-O of the Bay) (Port No.: 41-48)

  Module 4-port 2/4/8 Gb FC FlexIO (Flexi Bay 1) (Port No.: 49-56)

  FYI - I would like to install ESXi 6.0 on all blades

  Thank you!!

  Vinay

  Oriented server ports are configured automatically as part of the aggregation of links groups if the server is configured for the LACP Protocol. Static GAL is not supported.

  You will use the segregation network VLAN. A VLAN for network traffic and the other for the CF. Here are the commands to configure interfaces for different VLANS.

  Unidentified:

  Dell (conf) # tengigabit interface 0/16

  Dell(conf-if-te-0/16) # vlan unidentified 4

  Output Dell(conf-if-te-0/16) #.

  Tag:

  Dell (conf) # tengigabit interface 0/16

  The tag vlan Dell(conf-if-te-0/16) # 4

  Output Dell(conf-if-te-0/16) #.

  Traffic from servers will follow the path of the VLAN. For example, if an internal server, facing the port is set to VLAN 4, that traffic will be transmitted on the uplink port which has also set to VLAN 4.

  By default, all external ports are placed in a single whole LAG. However, you can change the configuration to support several shifts of uplink. Page 159 of guys configuration takes you step by step on setting up several shifts of uplink.

  The aggregator automatically configures to match the FCoE parameters used in the switches to which it connects through its uplink ports. FIP snooping is automatically configured on an aggregator. Automatically configured port channel (LAG 128) works CWF port mode. See page 86 for more information and examples of config.

  For redundancy, you could stack the units together. 241 page details the process of stacking.

  Page 54 of 102 of the Guide blade IO has one other diagram that details more internal server port mapping for each blade.

• Reference Dell 3110cn of Laserjet + os El Capitan

  My MacBook Pro (2009) stopped my Dell printer. News on this please.

  Hi deaconjo,

  as I had the same problem, I found a solution for my El Capitan MacPro 2008:

  Search for the following installation program:

  3130cn_Installer_And_Application_Dell_A04_MAC.dmg

  Inside this package you will find the driver for 10.7 and higher. After installing the package I could add an IP printer with this driver:

  Reference Dell 3130cn Color Laser v3017.104 PS

  With this driver installed, I can use my printer Dell 3110cn without problem.

  Perhaps it might help you too.

  Concerning

• Reference Dell Force10 S50N time in the same newspaper

  Hello

  first of all, I hope that a good place to ask question re Force10 devices - if not please forgive & point me to the right place

  I have following two stacked devices:

  Type of system: S50N
  Reference Dell Force10 operating system Version: 1.0
  Reference Dell Force10 Application Software Version: 8.4.2.6

  Recently, I have configured a source of time using ntp. display the clock command returns good time & ntp config also seem ok.

  I want to have the switch which had the correct timestamp of the date unit % hour however when logging to show browsing results shows this:

  32w6d12h: STKUNIT1% m: % LACP CP...
  32w6d12h: STKUNIT1% m: % LACP CP...
  32w6d12h: % STKUNIT1-% M:CP CMEA...

  That I am, I lack to set up/set for the date & time stamped and posted in the event logs?

  (I'm beginner in world Force10 and switch)

  Appreciate any help

  Hello

  I found horodateurs service order before but I was so blind to enter config mode.

  That worked very well.

  Thank you very much

• Reference Dell MD1200, H710 with R720XD

  Hello

  Asked if drieves NL - Seagate SAS (ST4000NM0023) can be used in the following configuration.

  Reference Dell Perc H710 + PowerEdge R720XD MD1200.

  The answer that I gave them was who should be tested. Because in documentation it is stated that mark Dell hard disks should be used.

  I know that some controllers Perc will give a warning each time if not dell disks are used, but they work without problems. Is this the case even when you use a box MD1200?

  Kind regards

  Indrek

  INDRP,

  You're right that only some drives are tested and supported in the bays of the MD. Here is a link that will take you to one of the manuals that list all drives supported for 1200 MD and MD1220.

  FTP.Dell.com/.../PowerVault-md1200_Reference%20Guide_en-US.pdf

  Please let me know if you have other questions I would be happy to help.

• Reference Dell 968 AIO, Windows 7 on Dell Studio XPS - messed up

  I have a Dell 968 AIO which was printing on the use of pilots (probably the original) on my Dell XPS Studio 8000 Win 7 pc, a week ago. He stopped printing a few days ago.

  I assumed the problem was the drivers and not the ink. So I tried to install the new drivers. It does not solve the problem. Indeed, the new drivers would not install completely. When he got to the last step of the installation the Setup program just hung. More on this in a minute.

  I bought new ink cartridges and allowed me to test the 968 printer and it prints very well now.

  However, when I tried to print a document from the computer.

  I tried to uninstall the old drivers and reinstall new drivers. Unfortunately, I got the USB cable is plugged. So I have messed up, and it would not print. He could not "locate the file. I tried after I unplug the USB stick and a running registry cleaning. Still no luck, but worse, I noticed that the installers had left a lot of luggage around.

  • There is a folder c:/dell/drivers/986, which seems to have a lot of the old drivers.
  • There was a folder c:/program files (x 86) /Dell AIO Printer 968
  • And there is also a folder c:/program files (x 86) (x 86) /Dell 968 AIO Printer.

  I followed the steps for a clean uninstall, and it is where I am now. However, there a lot of carrying files around in Dell matter folders on my hard drive.

  I'm sure I made a complete mess of things, can anyone help?

  Wendy

  Wendy,

  When you reinstalled the operating system, have you installed the desktop system software / laptop (as appropriate) and drivers from the chipset first? If this is not the case, the rest of the drivers will not install. How to download and install drivers in the correct order

  Start with the computer system software and the chipset drivers and follow the list.

  Once you have corrected, then we can work on the printer.

  First run, delete print jobs to eliminate any print job stuck in the queue.

  Unplug the printer.

  Download and run the patch (cleaning printer utility) until it prompts you to restart your computer.

  Restart your computer. Make sure that the printer is deleted. Driver Manual printer removal

  Download the 32-bit drivers for Vista for Windows 7 32-bit or 64-bit drivers for Windows 7 64 bit Vista. Install the Vista drivers in Vista compatibility mode, you will get a message, the printer is not connected. Connect the printer at the moment (power on).

  You will find links to the patch/drivers to...

  Reference Dell 968 & 968w all-in-One Printer owners thread (W7)

  Don't forget the programs anti-virus and firewall will block communications.

  Rick

• Reference Dell R210 II - update the Firmware on Centos 6

  Hello

  I have several dell servers connecting a mix of OS linux centos 5/6 for windows and xen etc.

  I have run it on every Linux machine to install the dell tools:

  wget - q - O - http://linux.dell.com/repo/hardware/latest/bootstrap.cgi | bash
  yum install srvadmin-all firmware-tools - y
  yum install $(bootstrap_firmware) y
  srvadmin - services.sh status
  / opt/dell/srvadmin/sbin CD.
  update_firmware - Yes

  on centos 5 is very well and on some centos 6 machines too. However, a new server got us set up this week, the following error occurs, I want to know how to solve this problem, so I can perform upgrades in the usual way via command line:

  Root@server[/opt/Dell/srvadmin/sbin]# update_firmware - Yes

  Inventory of the currently running system.

  Search the directory for storage of the available BIOS updates...
  Checking the BIOS - 2.2.3
  Available: dell_dup_componentid_00159 - 2.2.3
  Did not find a new installation package that meets all the checks of the facility.
  Verification of rev NetXtreme II Gigabit Ethernet 20 (em2) - 7.2.20 BCM5716
  Available: pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_0x04dd) - 7.4.8
  Found update: pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_0x04dd) - 7.4.8
  Check the system BIOS to PowerEdge R210 II - 2.2.3
  Did not find a new installation package that meets all the checks of the facility.
  Verification of rev NetXtreme II Gigabit Ethernet 20 (em1) - 7.2.20 BCM5716
  Available: pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_0x04dd) - 7.4.8
  Found update: pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_0x04dd) - 7.4.8

  Found the firmware that needs to be updated.

  Updates running...
  -Installation of pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_... Package installation failed: pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_0x04dd)
  -7.4.8.
  aborting update...

  The command to low-level error message was:

  Unable to parse xml output, bad for the package: pci_firmware (ven_0x14e4_dev_0x163b_subven_0x1028_subdev_0x04dd)
  Root@server[/opt/Dell/srvadmin/sbin]#

  the specification of the server:

  Reference Dell R210 II

  Intel Quad Core 3.2 Ghz
  16 GB of Ram
  CentOS 6.4 x 64
  1 x 256 GB SSD

  ChrisDuk112,

  Could you do me a favor and see if that solves the problem for you.

  the remount mount - o, suid, exec/tmp

  Let me know how it goes.

• Reference Dell 1700 crashed and I have no backup

  Reference Dell 1700 crashed without backup whats a girl to do
  
  

  lost all programs can run does not help

  Reference Dell 1700 crashed without backup whats a girl to do

  
  

  lost all programs can run does not help

  Reinstall Wndows.

  Reinstall all your programs from the original media or downloaded files you have saved on an external drive.

  Reinstall all your data from the backups that you made on an external drive.

  If you have not, you're out of luck.

• Reference Dell vostro 1520 with windows xp prof... Not reading CD/DVD

  Reference Dell vostro 1520 with windows xp prof... Unable to read & play any cd/dvd.tried mr.fixit content but no solution at the moment.

  Hello

  1 have. what fixit you tried?
  2. don't you make changes to the computer before the show?

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116

  Important: To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/) how to back up and restore the registry in the window.

• Cannot print. Reference Dell 944 communication usb port is not available. error check your firewall settings to ensure the printer communication is not blocked.

  Original title: unable to print. Reference Dell 944 communication usb port is not available.

  Message says 'check your firewall settings to ensure the printer communication is not blocked. Printer has worked faithfully until the problems started with the XP Home operating system. To cut a long story short ram upgraded to 2 GB, all unnecessary programs identified and technician Microsoft contacted to solve problems.  I was informed of problems caused by 3rd software party conflicts. Kaspersky was apparently the culpit. Dell Inspiron 32 now much faster but the printer will not work little matter what I do. I tried to reload with drivers & utility CD, drivers uninstalled & reinstalled on the site of all nothing is? Can someone help?

  DavidNicholsonXN,

  How to download and install drivers in the correct order

  also try to read...

  The owners of all-in-one printer Dell 944 thread (W7)

  Let the printer after Kaspersky

  Rick

• Reference Dell pc with xp family. Restart to the logon screen

  Reference Dell pc with xp family. Restart to the logon screen. starts ok in safe mode. run msconfig and do that no change then do restart ok everything ok until the cold start, then hand it to restart?

  Peek into the registry to find clues.

  Disable the automatic restart in case of system error and see if you can capture a message of error checking bug (BSOD) with useful information.  Automatic restart in the event of system failure can be disabled in the F8 advanced boot menu, or you can turn it off in system properties.

  1. right click on my computer and select Properties.
  2 - Click on the Advanced tab, and then click on the Start button and recovery settings.
  3 clear the automatically restart box and OK your way out system properties.

  Start the computer in a Clean Boot State, if the computer starts successfully in a clean boot state, then one of your user programs most likely problems, look in the case of journal of indexes.

  How to configure Windows XP to start in a "clean boot" State
  John

• Reference Dell downloads not recognized as 32-bit applications

  4 applications downloaded from Dell for DJ Jukebox GEN2. XP refuses to allow loading saying that it isn't 32 apps. These are:

  R95499.exe, R107735.exe, R88925.exe, R100928.exe.

  One is a driver, Playforsure AI program, two others are other applications of Dell for Juke Box Player firmware

  Appreciate your input

  Hello old salty

  1. What is the exact error you get when you try to install these drivers and applications?

  2 do you have Service Pack 3 installed on your computer?

  3. are you being invited to install these applications updates?

  4. do you get the error after having extracted the installation files?

  I see that there are different versions of all software. I suggest that you download and install the correct version that is compatible with Windows XP 32-bit.

  Please get back to us with the phase when the installation fails and an exact error message.

  You can also post your question on the forum Support of Dell. You can follow the link below to ask your question:

  http://en.community.Dell.com/support-forums/software-OS/default.aspx

  Thank you
  Irfan H, Engineer Support Microsoft Answers. Visit our Microsoft answers feedback Forum and let us know what you think.