Reference Dell perc h800

Similar Questions

• Reference Dell PERC 6 / i stand?

  I have a Setup Raid 6 on a Dell PERC 6 / i on a Supermicro H8DGU

  running a trial of the esxi 5.5u2

  No matter what I try, I can't do the Dell raid card is displayed in the storage adapters. I don't get any device also appear for passthrough if it means something.

  I have the AMD - V active and I had once made quick initialization (it's now the initialization in the background) I saw him appear on the list as a possible drive to install esxi. That tells me the esxi sees the card and the raid. But once I'm in vsphere nothing appears. Have not found a lot of messages from people not able to pick up this card so I think that the problem is just me. Ideas of things to check?

  But I guess that even with 'Boot Support' is enabled on Perc, is yet to appear in ESXi?

  I just checked your listing of motherboards to Supermicro. It employs riser card for the PCIe slots. Just to rule out it because there are a lot of wiring on the Perc: the card is well adjusted to the port of mounting?

  You can check if ESXi usually sees the device by runiing "lspci - vvv" on the CLI/ssh. It lists the devices seen by the kernel, if Perc is not here I would consider the Perc is defective or some strange PCIe connection problem.

  I have a Perc 6 / I works well for a client on a DELL Poweredge 2950 ex personalised Dell VMWare 5.5 Update 2 but on SAS, disks. But it's all DELL hardware and software side. I assume that the custom DELL VMWare image works only on DELL systems.

  I have found several traces as the Perc 6 / I could run a little crazy if you use disks not certified by DELL. Also the Perc 6 controllers do not seem to be supported more than 2 TB of drives (see for example: disk HARD Support for 2.5 to 3 TB drives and beyond - TechCenter Extras - Wiki - TechCenter Extras - Dell Community)

  So, you can probably run the test to disconnect all readers of your first and remove the Perc firmware RAID configuration and see if ESXi detects and it lists. If it does not help either I ran the test on different materials/mobo.

• Reference Dell PERC H710P: Firmware hangs on Windows RTM 8.1 with the default driver

  My H710P Dell (with the last FW A04) PERC was working completely fine with the driver 5.2.220.64 on Windows 8, until recently, I tried installing Windows RTM 8.1 on the machine, it caused hang FW at the launch of the Windows installation:

  266	[Information, 0]	05 seconds restart	Controller ID: 0 edge revision: A01	1367
  261	[Information, 0]	05 seconds restart	Controller ID: 0 Package version 21.2.0 - 0007	1366
  141	[Information, 0]	05 seconds restart	Controller ID: 0 battery present	1365
  1	[Information, 0]	04 seconds restart	Controller ID: 0 Image version: 3.130.05 - 2086	1364
  0	[Information, 0]	04 seconds restart	Controller ID: 0 has started the initialization of the Firmware: (PCI ID 0x5b / 0x1000 / 0x1f31 / 0 x 1028)	1363
  15	[Fatal, 3]	2013-09-11 21:00:27	Controller ID: 0 Fatal firmware error of: line 1232 in... /... /RAID/1078dma.c	1362
  15	[Fatal, 3]	2013-09-11 21:00:27	Controller ID: 0 Fatal firmware error of: line 1232 in... /... /RAID/1078dma.c	1361
  15	[Fatal, 3]	2013-09-11 21:00:27	Controller ID: 0 Fatal firmware error of: driver has detected possible FW, FW to stop blocking.	1360
  389	[Information, 0]	2013-09-11, 20:57:11	Controller ID: 0 host driver is loaded and operational	1359
  44	[Information, 0]	2013-09-11 20:56:33	Controller ID: 0 time established for power: time 2013-09-11 20:56:33 34 seconds	1358

  Windows 8.1 was delivered with the version of the downloadable 6.801.5.0 driver from Dell, I also tried and committed in my opinion the FW even hanging the question.

  I'm afraid - anyone know what is happening?

  See you soon

  Chris

  Appearantly this is related to the latest driver from Dell. I've found a workaround, but it's a bit complicated:

  1 connect a USB stick which is big enough

  2. install Wndows 8.1 on the * USB drive *.

  3. start Windows, and then remove the current driver and install the previous driver for Windows Server 2012.

  4. use the 3rd party software (say that Ghost) to copy the windows from USB drive to VD on Dell PERC H710P controller.

  5. start Windows in the USB drive again and use 'bcdedit' to clean boot stuff

  in any case, I'm LSI 9361-8i, so it won't be a problem for me in the future...

• Reference Dell Perc 6 ESXi T300

  I try to install ESXi on my dell T300. I have 4 hard drives on a raid Perc 6 controller, and I created a 5 to 2 TB raid array.

  I have advanced and installed ESXi on drives and connected with the client of the infrastructure. I try to add the storage remains in the system, so I can start putting a few images there.

  However my problem is the storage not appears between 26 and 45 GB when I added it to the system. When I try to add storage, capacity is listed as 2.05 TB but Availalble space is limited to 45,64 GB. Is there something I am missing with this?

  Thanks in advance.

  Welcome to the VMware community forums.  ESX (i) have a limit of 2 TB LUN.  With ESX it will used the first 2 TB and ignore the rest, but with ESXi for some reason, it ignores the pieces of 2 TB and use the rest (0.05 CT in your case).  If you re-create the matrix 2.0 TB - 512 B you will be able to use the total amount of storage.

• Reference Dell PERC H310 drivers

  I want to install a Windows Server 2008 operating system on a new PowerEdge R420 and I need to install the drivers for the PERC H310 controllers but I can't find the drivers as the only windows setup exe files or DUP which doesn't help since I always is not a running operating system.

  Can someone please tell me where to find this driver or how to get around this problem?

  Thank you

  You can use the switch/extract for the DUP or you can use the 'hard drive' version (ZPE).  Since you didn't say what version of 2008 you have been installing, I took the trouble to post all the:

  2008 x 64:
  http://downloads.Dell.com/FOLDER02416320M/2/SAS-RAID_WIN_Driver_W2K8X64_1KH1G_6.802.21.0_A06_ZPE.exe

  2008 x 86:
  http://downloads.Dell.com/FOLDER02416311M/2/SAS-RAID_Driver_W2K8X86_M62KG_6.802.21.0_A06_ZPE.exe

  2008R2:
  http://downloads.Dell.com/FOLDER02416328M/2/SAS-RAID_Driver_W2K8R2_D5N8T_A06_6.802.21.00_ZPE.exe

• Reference Dell MD1200, H710 with R720XD

  Hello

  Asked if drieves NL - Seagate SAS (ST4000NM0023) can be used in the following configuration.

  Reference Dell Perc H710 + PowerEdge R720XD MD1200.

  The answer that I gave them was who should be tested. Because in documentation it is stated that mark Dell hard disks should be used.

  I know that some controllers Perc will give a warning each time if not dell disks are used, but they work without problems. Is this the case even when you use a box MD1200?

  Kind regards

  Indrek

  INDRP,

  You're right that only some drives are tested and supported in the bays of the MD. Here is a link that will take you to one of the manuals that list all drives supported for 1200 MD and MD1220.

  FTP.Dell.com/.../PowerVault-md1200_Reference%20Guide_en-US.pdf

  Please let me know if you have other questions I would be happy to help.

• Reference DELL T420 - battery on PERC H710 adapter controller

  Hello

  I received a yellow warning

  Reference DELL T420 'Battery on PERC H710 adapter controller'

  What it means?

  What should I do?

  Order the new battery?

  It is a simple replacement mission?

  Is it essential?

  Update:

  test URL

  http://www.Dell.com/support/article/us/en/04/SLN130018

  Have nothing, everything seems fine now...

  Thank you

  It is normal so he can make a full discharge of the battery as part of his learning cycle every 90 days. Make sure that this isn't that. If this isn't the case, the reason, give it 24 hours. If it is fully charged, update the system (including RAID firmware, driver first) firmware. If not fully charged yet or it reproduces quickly, then replace the battery - power down to replace.

• Dell Power Edge R410 & Dell Perc H700 modular F2WGY

  Hi guys

  Need some advice please, a few weeks ago, we bought a Dell R410. This came with a modular 6/ir Perc. However, when we arrived at the installation of drives we noticed that the controller did not recognize disks larger than 2 TB. It's not good because we need to use 2 x 3 and 2 x 500 GB disks in a RAID 1 Configuration.

  After Googling autour, I came to the conclusion that the card that it came with the "Perc 6/ir' does not support disks larger than 2 TB.

  So, I advanced and bought a new modular a "Dell Perc H700 F2WGY" controller which apparently supports disks more great.

  the controller came yesterday so I removed the old Perc 6/ir controller from the slot in the bottom of the map editing and trendy "Dell Perc H700 F2WGY" modular at the same place. : Photo of slot, I inserted H700

  H700 card: see picture

  PERC 6/ir map: see picture

  Anyway, once I inserted the card and started, I was presented with the error; "PCIE training error" system HALT.

  Obviously this would not start any further. So I brought the wrong card? im confused at the moment between modular and integrated? the pcie slot is low for integrated only cards?

  I then add the new map on the PCIE Top slot. the system then started and he could see the card. However, it found no readers?

  What exactly I do bad will this card work at all? or I'm out of luck and need another card?

  Cappilio,

  The problem you are experiencing is due to the model of the H700. Map H700 modular version is actually designed for the blade server Poweredge series. The model that you would need is the H700i which is the version that is integrated, designed to go into the white storage controller slot you are talking about. The references are KK67X and CNXVV. The latest model of the H700 is the H700A which is the adapter, it's the model that is necessary for installation in a PCIe location.

  This link explains in detail in the overview H700 - http://www.dell.com/downloads/global/products/pvaul/en/perc-technical-guidebook.pdf

  Let me know if it helps.

• Reference Dell 1700 crashed and I have no backup

  Reference Dell 1700 crashed without backup whats a girl to do
  
  

  lost all programs can run does not help

  Reference Dell 1700 crashed without backup whats a girl to do

  
  

  lost all programs can run does not help

  Reinstall Wndows.

  Reinstall all your programs from the original media or downloaded files you have saved on an external drive.

  Reinstall all your data from the backups that you made on an external drive.

  If you have not, you're out of luck.

• Reference Dell vostro 1520 with windows xp prof... Not reading CD/DVD

  Reference Dell vostro 1520 with windows xp prof... Unable to read & play any cd/dvd.tried mr.fixit content but no solution at the moment.

  Hello

  1 have. what fixit you tried?
  2. don't you make changes to the computer before the show?

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116

  Important: To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/) how to back up and restore the registry in the window.

• Cannot print. Reference Dell 944 communication usb port is not available. error check your firewall settings to ensure the printer communication is not blocked.

  Original title: unable to print. Reference Dell 944 communication usb port is not available.

  Message says 'check your firewall settings to ensure the printer communication is not blocked. Printer has worked faithfully until the problems started with the XP Home operating system. To cut a long story short ram upgraded to 2 GB, all unnecessary programs identified and technician Microsoft contacted to solve problems.  I was informed of problems caused by 3rd software party conflicts. Kaspersky was apparently the culpit. Dell Inspiron 32 now much faster but the printer will not work little matter what I do. I tried to reload with drivers & utility CD, drivers uninstalled & reinstalled on the site of all nothing is? Can someone help?

  DavidNicholsonXN,

  How to download and install drivers in the correct order

  also try to read...

  The owners of all-in-one printer Dell 944 thread (W7)

  Let the printer after Kaspersky

  Rick

• Reference Dell pc with xp family. Restart to the logon screen

  Reference Dell pc with xp family. Restart to the logon screen. starts ok in safe mode. run msconfig and do that no change then do restart ok everything ok until the cold start, then hand it to restart?

  Peek into the registry to find clues.

  Disable the automatic restart in case of system error and see if you can capture a message of error checking bug (BSOD) with useful information.  Automatic restart in the event of system failure can be disabled in the F8 advanced boot menu, or you can turn it off in system properties.

  1. right click on my computer and select Properties.
  2 - Click on the Advanced tab, and then click on the Start button and recovery settings.
  3 clear the automatically restart box and OK your way out system properties.

  Start the computer in a Clean Boot State, if the computer starts successfully in a clean boot state, then one of your user programs most likely problems, look in the case of journal of indexes.

  How to configure Windows XP to start in a "clean boot" State
  John

• Reference Dell M1000e + aggregator MI/O port mapping

  Hi all

  I intend to install a new chassis Dell M1000e with Dell M/o aggregator. During the time of solution, I have a few questions about correspondences between the physical uplink with NDC blade ports ports. A Please check the config below and specify my queries?

  My hardware:

  • 1 x Dell M1000e
  • 2 x M i/o aggregator (A1 & A2)
  • 16 x M630 Blade (Qlogic 57840 S ANC four ports card)

  Reference DELL M/o aggregator:

  (reserved for Future use) module QSFP + 2 ports (Port No1:33 - 36 & No2:37 Port-40)

  I want to use these two modules for my blades 4-port Quad and the confusion I had, how to associate these 16 ports (8 ports of each module) to the server blade and the amount of bandwidth I will get by blade with redundancy.

  Module 4-port SFP + 10 GbE (Flexi-O of the Bay) (Port No.: 41-48)

  Module 4-port 2/4/8 Gb FC FlexIO (Flexi Bay 1) (Port No.: 49-56)

  FYI - I would like to install ESXi 6.0 on all blades

  Thank you!!

  Vinay

  Oriented server ports are configured automatically as part of the aggregation of links groups if the server is configured for the LACP Protocol. Static GAL is not supported.

  You will use the segregation network VLAN. A VLAN for network traffic and the other for the CF. Here are the commands to configure interfaces for different VLANS.

  Unidentified:

  Dell (conf) # tengigabit interface 0/16

  Dell(conf-if-te-0/16) # vlan unidentified 4

  Output Dell(conf-if-te-0/16) #.

  Tag:

  Dell (conf) # tengigabit interface 0/16

  The tag vlan Dell(conf-if-te-0/16) # 4

  Output Dell(conf-if-te-0/16) #.

  Traffic from servers will follow the path of the VLAN. For example, if an internal server, facing the port is set to VLAN 4, that traffic will be transmitted on the uplink port which has also set to VLAN 4.

  By default, all external ports are placed in a single whole LAG. However, you can change the configuration to support several shifts of uplink. Page 159 of guys configuration takes you step by step on setting up several shifts of uplink.

  The aggregator automatically configures to match the FCoE parameters used in the switches to which it connects through its uplink ports. FIP snooping is automatically configured on an aggregator. Automatically configured port channel (LAG 128) works CWF port mode. See page 86 for more information and examples of config.

  For redundancy, you could stack the units together. 241 page details the process of stacking.

  Page 54 of 102 of the Guide blade IO has one other diagram that details more internal server port mapping for each blade.

• Reference Dell 3110cn of Laserjet + os El Capitan

  My MacBook Pro (2009) stopped my Dell printer. News on this please.

  Hi deaconjo,

  as I had the same problem, I found a solution for my El Capitan MacPro 2008:

  Search for the following installation program:

  3130cn_Installer_And_Application_Dell_A04_MAC.dmg

  Inside this package you will find the driver for 10.7 and higher. After installing the package I could add an IP printer with this driver:

  Reference Dell 3130cn Color Laser v3017.104 PS

  With this driver installed, I can use my printer Dell 3110cn without problem.

  Perhaps it might help you too.

  Concerning

• Reference Dell Sonicwall SRA

  Hey guys, more of a statement than a question. If you have a Dell Sonicwall and users do "found no appropriate group" of course the same user does not exist as a local user and a domain user. This will cause problems. Took me a while to understand that >.<>

  Good thought.

  Thank you
  Ben D
  Reference Dell SonicWall
  #Iwork4dell