Remote Access connects with shared connection, but when I connect the Ethernet to the box Belkin Wireless cable, there is no network connection

I have dial-up internet. I have to computers. A PC running XP and a laptop that is running Windows 7.
I have the connection shared, if I plug the Ethernet cable to the laptop, it will connect to the internet. I just bought a Belkin G wireless router.
I want to know how to configure it, then the router Belkin Wireless put the switched signal shared wireless. I know it's possible, I'm not sure what I'm doing wrong. It is constantly with him saying on the phone "the DNS server does not respond.

Advertisement

Connect the Ethernet cable from your PC to the WAN (Internet) port on the wireless router.  Do not connect to one of the router's LAN ports. Boulder computer Maven
Most Microsoft Valuable Professional

Tags: Windows

Similar Questions

  • Acrobat Pro 9 - I want to add a watermark, but when I opened the box of watermark...

    I want to add a watermark, but when I opened the box to watermark it opens to big for my screen. The bottom of the page is not in view at the bottom. I'm guessing that the button apply or the OK button at the bottom is because I'm not able to get my watermark. I unlocked my taskbar and tried to click on the header for the move and size left. No use.

    You need to change your screen resolution, in order to see this section at the bottom.  I have the same problem, because I have bad eyesight and keep my resolution to widescreen.

  • Received the email of validation with redemption code, but when I enter the redemption code, it says that it is not valid

    What is the problem?

    In this case I would advice you Contact Customer Care

  • When I try to start the Remote Access Connection Manager in services.msc, the service will not start.

    Rick2425

    When I try to start the Remote Access Connection Manager in services.msc, the service will not start. I get the same error: "Windows could not start the service of connection manager on the local computer remote access: Error 1068: the dependency service or group could start."  Also, I can not restore the system to come and let me run it.

    It is a Dell PP31L, which belongs to a friend who does not connect to the internet because of these error messages.

    Hello Rick2425

    See the thread below and let me know if it helps thanks.

    http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-networking/error-1068-remote-access-connection-manager/b5155a8a-671e-4d11-8a99-deadc7aee8a1

  • Can not get to start remote access connection manager and the connections don't work Internet

    Original title: wired & wireless connections does not.

    I can not get the remote access connection manager to start and so no internet connection is not working, also I can't open the system restore to go back on this machine. What is this?

    I am running a Dell Studio 1735 PP31L w model number / Edition Vista Home premium.

    Hi Rick,

    1. what happens when you try to start the remote access connection manager? You receive messages or error codes?

    2. you receive error codes or restore messages when you perform the system?

    You can check the status of the following services and make sure that the services are started.

    a. Click Start and type Services in start search and press ENTER.

    b. in the services with the right button on the phone and then click Properties.

    c. under the general tab, select automatic next to startup type.

    d. under the general tab, click Start under the service status and then click apply and then click OK.

    e. Repeat steps c & d to the remote access connection manager and Remote Access Auto Connection Manager service.

    Hope this information is useful.

  • The remote access connection manager could not start. Error 2: cannot find the specified file.

    I've updated from vista to the most recent update.

    I have windows vista Home premium 32-bit.
    I want to get this matter resolved without having to reinstall as I have a few games installed it on this system.
    The modem is not the issue as other computers connect very well.
    Thanks for the help from Microsoft.
    Recently, I tried to connect to the internet but that was not possible, because no connection could be established. The remote access connection manager does not start 2 error: could not find the specified domain. the RasMan-dependent services are started, but Manager logins remote does not start.

    Hi Mundilfar,

    You can try the folliwng steps and see if it helps.

    Step 1:

    You can try to scan the file system [SFC] checker on the computer that will replace missing or corrupt files & check if the problem persists.

    For more information, you can consult the following link.

    How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

    Step 2:

    If you are always faced with the question, then you can try to give permission for the Rasman registry key and see if it helps.

    Important: The following steps show you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

    For more information about how to back up and restore the registry, follow the steps from the link below:

    Back up the registry

    a. Click Start, type regedit in the search box and press ENTER.

    b. Locate the following subkey:

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\RasMan

    c. right click on the key and click Permissions.

    d. Select Advanced, click on owner tab, click your user name, and check the 'Replace owner of subcontainers and objects', click Apply - click OK.

    e. click the user or group name that you want to work with.

    f. check allow total control. Click apply and then click OK.

    g. restart the computer and check.

    Hope this information is useful.

  • After the remote access connection, network printers disconnected

    I hope someone can help me here.

    In Windows Vista, whenever I would give the remote access connection to my PC at home, my default printer (which was be a shared printer on the network out of my server) will prepare its default value.  It was boring but easily fixible.

    I've since upgraded to Windows 7 Ultimate and I'm having a related problem.  Now every time I connect remotely to my home PC, my default printer (same network shared printer - HP LJ 4000) disconnects, and it only comes back online after a reboot.

    It is a point of pain is huge for me because I usually 20 + / applications windows running at a given time and a restart takes 30 minutes out of my day to get back to where I was.

    Any help would be appreciated. Jeff Balcerzak

    http://h30434.www3.HP.com/T5/printer-all-in-one-software-and/Windows-7-C7200-C7280-offline/m-p/167672

    http://social.technet.Microsoft.com/forums/en/w7itpronetworking/thread/0cfa31d7-B44B-4241-aa31-d0ae9f0a2112

    http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c00843712&tmp_track_link=ot_faqs/top_issues/en_US/c00843712/loc:8 & lc = en & dlc = en & cc = us & product = 1153481 & lang = en

  • Failed to start Remote Access Connection Manager Service. Get the 20 error: the system cannot find the specified device.

    This seems to have started with the last batch of updates of Windows 7 (including SP1).
    I can't connect using dial-up.  Get the message:
    Cannot load the Remote Access Connection Manager service
    Error 711: The operation could not complete because it could not start the remote access connection manager service
    in time.  Please try the operation again.

    When I try to start the Remote Access Connection Manager service manually, I get the message:
    Windows could not start the service on Local computer remote access connection manager.
    20 error: the system cannot find the specified device.

    My phone displays the modem works properly, and telephony and the Secure Socket Tunneling Protocol service started.

    I don't know what else might have changed.

    Hello Vince_867,

    Thanks for your post.  Take a look at this thread for a possible solution to your problem.

    See you soon

  • Why can't I start Remote Access Connection Manager

    I am not able to connect to internet using my 3G Broadband. I try to resolve the status of the remote access connection manager to "on the road", but the error message invites up to said "Windows could not start the service on local computer remote access connection manager. Error 1068: the dependency service or group could start. "I find the dependencies are Remote Access Auto Connection Manager, routing and remote access, Sharing (ICS) to connect Internet. I tried to put those 3 to "started", but was able to start also.

    Hello
     
    You must make sure that the underside of services are started and restart your computer and check if the problem is resolved.
     
    To start the services.
     
    1. click on start.
    2. type Services.msc in the search box and click on enter.
     
    Note: the common addiction for "Remote Access Connection Manager" and 'Remote Access Auto Connection Manager' is 'Secure Socket Tunneling Protocol Service'.
     
    Make sure that you check the properties of service no matter what you try to start, then click the dependency tab and make sure that you select the dependency registered under this service services.
     
    The dependency of 'Remote access connection manager' services include:
     
    a. secure Socket Tunneling Protocol Service
    b. phone
    c. Plug-and-Play
    d. remote Procedure Call (RPC)
    e. DCOM Server process Launcher
    f. RPC end point mapper
     
    Make sure that you try to start the Connection Manager Service dependency services automatic remote access as well.
     
    Method 2:
     
    I recommend you to update the drivers and see if it makes a difference. You must be logged on as administrator to perform these steps.
     
    1. open Device Manager by clicking the Start button, click on the Control Panel, clicking system and Maintenance, and then clicking Device Manager. If you are prompted for an administrator password or a confirmation, type the assword or provide confirmation.
    2. in Device Manager, locate the device, and then double-click the device name.
    3. click Driver tab, then click on set to update driver and follow the instructions.
     
    Try to follow the link provided to update a hardware driver that is not working properly and check the question below.
    http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

    Thank you, and in what concerns:
    I. Suuresh Kumar - Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • iPod 120 GB Classic is recognized by iTunes, but it will not be synchronized. I ran the diagnostic. The connectivity of the device test showed the iPod, but when I ran the test of synchronizing device, it says that no device was found. It didn't Sync befo

    I have a version of the software running iPod Classic 2.0.4 of 160 GB. The iPod has not been synchronized for more than a month. I did diagnostic tests today. The connectivity of the device test showed the iPod, but when I ran the test of synchronizing device, he said that there was no iPod found. I checked and installed new updates, but it is not always sync. I restarted iTunes and computer, but it is not always sync. I ran a diagnostic on the device and it showed that it was operating normally.

    The iPod must be configured to synchronize automatically.  If this is not the case, click Sync does not synchronize no matter what.

    Select the iPod in iTunes, so that you see the iPod settings screen in the iTunes window.  Along the left side of the window, in the sidebar, under settings, click on music.  To the right, you will see a settings screen of the iPod music , where you tell iTunes how to sync songs to the iPod.

    NOTE: All the songs on the iPod that are NOT in your iTunes library (on the computer) will be lost.  If all the songs are in your iTunes library, no problem.

    At the top of the window, check the box to Sync music.  This enables automatic synchronization.  Below, select the option to synchronize library of ensemble music, if you want to 'all' in your music library to sync.  At the bottom, click on the apply button.

    From now on, when you make changes to your iTunes music library (like add new songs or update a playlist), iTunes automatically updated the iPod with the same changes when you connect (or click sync , if already connected).

  • Error 1068: the dependency service or group failed to start and failed to start the remote access connection manager service.

    Original title: Windows could not start the service of connection manager on the local computer remote access

    amplifier

    Windows could not start the service of connection manager on the local computer remote access

    Error 1068: The dependency Service or group could start.

    Hi sunelchandraoli,

    1. when exactly you receive this error?

    2. you remember to make changes to the computer before this problem?

    Step 1:

    "Make sure that all the services of the dependence of the"Remote Access Connection Manager"" are launched in the list of services...

    a. Click Start, type services.msc in the box start the search.

    b. select Services from the list programs. If you are prompted for an administrator password or a confirmation, type your password or click on continue

    c. right click on the Remote Access Connection Manager service and then click Properties.

    d. under the general tab, click Manual next to startup type.

    e. under the general tab, click Start under the service status and then click OK.

    f. also check for long-term services.

    The dependency of 'Remote access connection manager' services include:

    i. secure Socket Tunneling Protocol Service

    II. telephone

    III. Plug-and-Play

    IV. Remote Procedure Call (RPC)

    c. of DCOM Server process Launcher

    VI RPC end point mapper.

    Make sure that the above services are started in the services list. If this is not the case, start all services above and check.

    Step 2:

    You can also try a system restore to a prior restore point you have been affected by the issue.

    Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.

    To run the system restore, you can consult the following link:

    System restore

    http://Windows.Microsoft.com/en-us/Windows7/what-is-system-restore

    System Restore: frequently asked questions

    http://Windows.Microsoft.com/en-us/Windows7/system-restore-frequently-asked-questions

    Hope this information is useful.

  • Remote Access Connection Manager

    What is Remote Access Connection Manager and what is it?        PS. I don't know what Windows topic category and applications, this falls under, but since I HAD to choose one...  Thank you for your help.

    Hi bjeja,

    Welcome to the Microsoft community where you can find all the answers related to windows.

    Remote Access Connection manager manages connections dial-up and virtual private network (VPN) from the computer to the Internet or other remote networks.

    If you have questions about Windows do not hesitate to answer and we will be happy to help.

  • Lose connection Wireless at some site but when work around the site router works

    Original title: Wireless problems

    When I am connected to my wireless router, some sites such as who's who, I lose the internet connection. He said SSL issues.or CE NE MAY NOT BE THE SITE YOU ARE looking for "but when I bypass the router, the problem goes away. There are other laptop on the router there is NO problem. What can I do?

    Hello Dennis,.

    I'm sorry that you have a problem trying to connect to some Web sites.

    Just to make sure I understand your question, you lose the internet connection only to some Web sites, but if you unplug your router, you are able to connect to the website like Facebook without problem.

    Let's start with the basics on the wireless connection.
    -Make sure that the cables are properly connected to the router.
    -Restart your router, turn it off for 45 seconds and then turn it back on
    -Try again to connect to the problem site.
    -Update your drivers for your network card wireless

    Then I'd suggest that you update the firmware on your router. Go to the router manufacturer's website and download the latest version of the software package.

    Here is some information on the use of networks wireless that might be useful:
    http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

    If you still encounter a problem after trying the steps, answering the post again and I'll be happy to work with you for additional options.

    Sincerely,

    Marilyn

  • I can't connect to my account. He says that I already have a LIVE account when I enter my e-mail address, but when I use the "forgotten password", it says that this account does not exist. WTF?

    I can't connect to my account. He says that I already have a LIVE account when I enter my e-mail address, but when I use the "forgotten password", it says that this account does not exist.  WTF?

    Hello

    For questions related to the application, Windows Live, Windows Live Support professionals/moderators will be best placed to help you. I recommend you to ask your question in the support forum for Windows Live for assistance:

    http://www.windowslivehelp.com/

    Hope the helps of information.

  • I try to add the Youtube widget, but I get a plugin saying blocked black box. I even tried to incorporate both YouTube and it does the same thing. But when I drag the widget Vimeo more, it connects properly. What I am doing wrong and

    I try to add the Youtube widget, but I get a plugin saying blocked black box. I even tried to incorporate both YouTube and it does the same thing. But when I drag the widget Vimeo more, it connects properly. What I am doing wrong and how can I solve this problem?

    Make sure that the web browser you are using and its Flash plug-in is up-to-date. Google Chrome has its own plug-in Flash, it updates on its own. Firefox, IE and others have separate plug-ins.

Maybe you are looking for


HashFlare