Remote Access Service Console

Is there a way to access the VMware host service console remotely?

Try to run the command "dcui" in an SSH session...

Direct Console User Interface (DCUI) since a SSH session access (2039638). VMware KB

/ Rubeck

Tags: VMware

Similar Questions

  • Failed to start remote access service

    Hello

    I get a vps and I install ca and iis and the remote access service

    I allow it as a vpn server

    When I try to run the remote access service there gives me an error

    The Routing and remote access is dependent on the Remote Access Connection Manager service, which could not start due to the following error:

    The dependency service or group was able to start.

    I reslove this problem to run these commands:

    netcfg u ms_sstp

    netcfg - c p-i ms_sstp.

    net start sstpsvc

    net start rasman

    now when I am tempted to throw there gives me this error:

    The Remote Access Connection Manager service terminated with the following error:

    The system cannot find the specified device.

    So what is the problem?

    Thank you.

    Hello

    Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Microsoft TechNet forum. You can follow the link to your question:

    http://social.technet.Microsoft.com/forums/en-us/categories

  • Where can I get a download for Windows XP Service Pack 3 disc? I remote access service and cannot download it online.

    PeoplePC disconnected until the download is complete; Therefore, it loses data downloading and Service Pack 3 does not boot to Windows. Computer must be retrieved from partition-all installed programs must be re-installed or downloaded again. It takes some days with the remote access service.

    You can order a CD from Microsoft or download online.

    "How to obtain the latest Service Pack for Windows XP"
    HTH,
    JW
  • ASA 5505 - remote access VPN to access various internal networks

    Hi all

    A customer has an ASA 5505 with a remote access vpn. They are moving their internal network to a new regime and that you would be the users who come on the vpn to access the existing and new networks. Currently can only access the existing. When users connect to access remote vpn, the asa gave them the address 192.168.199.x. The current internal network is 200.190.1.x and that they would reach their new network of 10.120.110.x.

    Here is the config:

    :

    ASA Version 8.2 (5)

    !

    ciscoasa hostname

    enable encrypted password xxx

    XXX encrypted passwd

    names of

    !

    interface Ethernet0/0

    switchport access vlan 2

    !

    interface Ethernet0/1

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 200.190.1.15 255.255.255.0

    !

    interface Vlan2

    nameif outside

    security-level 0

    IP address 255.255.255.0 xxxxxxx

    !

    exec banner the ACCESS NOT AUTHORIZED IS STRICTLY PROHIBITED

    connection of the banner the ACCESS NOT AUTHORIZED IS STRICTLY PROHIBITED

    banner asdm the ACCESS NOT AUTHORIZED IS STRICTLY PROHIBITED

    passive FTP mode

    access extensive list ip 200.190.1.0 inside_access_in allow 255.255.255.0 any

    outside_access_in list extended access permit icmp any external interface

    access extensive list ip 192.168.199.0 outside_access_in allow 255.255.255.192 host 10.120.110.0

    Standard access list MD_IPSEC_Tun_Gp_splitTunnelAcl allow 200.190.1.0 255.255.255.0

    MD_IPSEC_Tun_Gp_splitTunnelAcl list standard access allowed host 10.120.110.0

    access extensive list ip 200.190.1.0 inside_nat0_outbound allow 255.255.255.0 192.168.199.0 255.255.255.192

    inside_nat0_outbound list extended access allowed host ip 10.120.110.0 192.168.199.0 255.255.255.192

    pager lines 24

    Enable logging

    asdm of logging of information

    Within 1500 MTU

    Outside 1500 MTU

    mask 192.168.199.10 - 192.168.199.50 255.255.255.0 IP local pool Remote_IPSEC_VPN_Pool

    IP verify reverse path to the outside interface

    ICMP unreachable rate-limit 1 burst-size 1

    ICMP allow any inside

    ICMP allow all outside

    don't allow no asdm history

    ARP timeout 14400

    Global 1 interface (outside)

    NAT (inside) 0-list of access inside_nat0_outbound

    NAT (inside) 1 200.190.1.0 255.255.255.0

    inside_access_in access to the interface inside group

    Access-group outside_access_in in interface outside

    Route outside 0.0.0.0 0.0.0.0 190.213.43.1 1

    Route inside 10.120.110.0 255.255.255.0 200.190.1.50 1

    Route inside 192.168.50.0 255.255.255.0 200.190.1.56 1

    Route inside 192.168.60.0 255.255.255.0 200.190.1.56 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    Floating conn timeout 0:00:00

    dynamic-access-policy-registration DfltAccessPolicy

    http server enable 10443

    http server idle-timeout 5

    Server of http session-timeout 30

    HTTP 200.190.1.0 255.255.255.0 inside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs

    Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    outside_map interface card crypto outside

    Crypto ca trustpoint _SmartCallHome_ServerCA

    Configure CRL

    Crypto ca certificate chain _SmartCallHome_ServerCA

    certificate ca 6ecc7aa5a7032009b8cebcf4e952d491

    (omitted)

    quit smoking

    crypto ISAKMP allow outside

    crypto ISAKMP policy 10

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    Crypto isakmp nat-traversal 3600

    Telnet timeout 5

    SSH 200.190.1.0 255.255.255.0 inside

    SSH timeout 5

    SSH version 2

    Console timeout 5

    dhcpd outside auto_config

    !

    a basic threat threat detection

    scanning-threat shun threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    allow outside

    internal MD_SSL_Gp_Pol group strategy

    attributes of Group Policy MD_SSL_Gp_Pol

    VPN-tunnel-Protocol webvpn

    WebVPN

    list of URLS no

    disable the port forward

    hidden actions no

    disable file entry

    exploration of the disable files

    disable the input URL

    internal MD_IPSEC_Tun_Gp group strategy

    attributes of Group Policy MD_IPSEC_Tun_Gp

    value of banner welcome to remote VPN

    VPN - connections 1

    VPN-idle-timeout 5

    Protocol-tunnel-VPN IPSec webvpn

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list MD_IPSEC_Tun_Gp_splitTunnelAcl

    the address value Remote_IPSEC_VPN_Pool pools

    WebVPN

    value of the RDP URL-list

    attributes of username (omitted)

    VPN-group-policy MD_IPSEC_Tun_Gp

    type of remote access service

    type tunnel-group MD_SSL_Profile remote access

    attributes global-tunnel-group MD_SSL_Profile

    Group Policy - by default-MD_SSL_Gp_Pol

    type tunnel-group MD_IPSEC_Tun_Gp remote access

    attributes global-tunnel-group MD_IPSEC_Tun_Gp

    address pool Remote_IPSEC_VPN_Pool

    Group Policy - by default-MD_IPSEC_Tun_Gp

    IPSec-attributes tunnel-group MD_IPSEC_Tun_Gp

    pre-shared key *.

    !

    !

    context of prompt hostname

    : end

    The following ACL and NAT exemption ACL split tunnel is incorrect:

    MD_IPSEC_Tun_Gp_splitTunnelAcl list standard access allowed host 10.120.110.0

    inside_nat0_outbound list extended access allowed host ip 10.120.110.0 192.168.199.0 255.255.255.192

    It should have been:

    Standard access list MD_IPSEC_Tun_Gp_splitTunnelAcl allow 10.120.110.0 255.255.255.0

    access extensive list ip 10.120.110.0 inside_nat0_outbound allow 255.255.255.0 192.168.199.0 255.255.255.192

    Then 'clear xlate' and reconnect with the VPN Client.

    Hope that helps.

  • The Routing and remote access could not start, error 214500037 (0x80004005)

    My windows server 2003 r2, failed to start the Routing and remote access services. And in the event an observer log, it has error code
    Event ID: 7024, with service specific error 2147500037 (0x80004005)
    I tried to reset tcp/ip and replace ias.mdb and dnary.mdb by a new, but it did not work.

    Thank you

    Hi budhihartono,

    Since you are facing problems with windows server 2003 r2, it would be better suited in the Technet Windows forum. Please post your question in the following TechNet Windows server forum to improve assistance:

    http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

  • When I try to start the Remote Access Connection Manager in services.msc, the service will not start.

    Rick2425

    When I try to start the Remote Access Connection Manager in services.msc, the service will not start. I get the same error: "Windows could not start the service of connection manager on the local computer remote access: Error 1068: the dependency service or group could start."  Also, I can not restore the system to come and let me run it.

    It is a Dell PP31L, which belongs to a friend who does not connect to the internet because of these error messages.

    Hello Rick2425

    See the thread below and let me know if it helps thanks.

    http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-networking/error-1068-remote-access-connection-manager/b5155a8a-671e-4d11-8a99-deadc7aee8a1

  • Error 1068: the dependency service or group failed to start and failed to start the remote access connection manager service.

    Original title: Windows could not start the service of connection manager on the local computer remote access

    amplifier

    Windows could not start the service of connection manager on the local computer remote access

    Error 1068: The dependency Service or group could start.

    Hi sunelchandraoli,

    1. when exactly you receive this error?

    2. you remember to make changes to the computer before this problem?

    Step 1:

    "Make sure that all the services of the dependence of the"Remote Access Connection Manager"" are launched in the list of services...

    a. Click Start, type services.msc in the box start the search.

    b. select Services from the list programs. If you are prompted for an administrator password or a confirmation, type your password or click on continue

    c. right click on the Remote Access Connection Manager service and then click Properties.

    d. under the general tab, click Manual next to startup type.

    e. under the general tab, click Start under the service status and then click OK.

    f. also check for long-term services.

    The dependency of 'Remote access connection manager' services include:

    i. secure Socket Tunneling Protocol Service

    II. telephone

    III. Plug-and-Play

    IV. Remote Procedure Call (RPC)

    c. of DCOM Server process Launcher

    VI RPC end point mapper.

    Make sure that the above services are started in the services list. If this is not the case, start all services above and check.

    Step 2:

    You can also try a system restore to a prior restore point you have been affected by the issue.

    Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.

    To run the system restore, you can consult the following link:

    System restore

    http://Windows.Microsoft.com/en-us/Windows7/what-is-system-restore

    System Restore: frequently asked questions

    http://Windows.Microsoft.com/en-us/Windows7/system-restore-frequently-asked-questions

    Hope this information is useful.

  • Failed to start Remote Access Connection Manager Service. Get the 20 error: the system cannot find the specified device.

    This seems to have started with the last batch of updates of Windows 7 (including SP1).
    I can't connect using dial-up.  Get the message:
    Cannot load the Remote Access Connection Manager service
    Error 711: The operation could not complete because it could not start the remote access connection manager service
    in time.  Please try the operation again.

    When I try to start the Remote Access Connection Manager service manually, I get the message:
    Windows could not start the service on Local computer remote access connection manager.
    20 error: the system cannot find the specified device.

    My phone displays the modem works properly, and telephony and the Secure Socket Tunneling Protocol service started.

    I don't know what else might have changed.

    Hello Vince_867,

    Thanks for your post.  Take a look at this thread for a possible solution to your problem.

    See you soon

  • Service of ASA module does on 6509-E support remote access VPN?

    I'm having a problem of configuration of remote access VPN (SSL, Anyconnect ect.) on the Module of ASA Service on 6509-E. It is even supported or I'm wasting my time trying to do something that won't work in a first place :) to work? Site-to-Site works without any problem.

    Technical info:

    6509-E current SUP 2 t SY 15.1 (2)

    Module of ASA - WS-SVC-ASA-SM1 running of the image - asa912-smp-k8 & asdm-712

    Licenses on ASA:

    Encryption--Activated

    3DES-AES-Encryption - enabled

    Thank you for the support.

    You run multiple context mode?

    If you are, access remote VPN only is not supported in this case:

    "Note several context mode only applies to the IKEv2 and IKEv1 site to another and applies not to the AnyConnect, clientless SSL VPN, the legacy Cisco VPN, native VPN client client of Apple, the VPN client from Microsoft or cTCP for IKEv1 IPsec."

    Reference.

  • How to access the ESX service console

    Hi all.

    I'm a TV engineer trying to solve a problem of network with our equipment. I'm not a network engineer.

    I'm trying to follow the VMWareKB: "Troubleshooting connection problems network using the Protocol ARP (Address Resolution)" I'm just trying to check the ARP table exists on our ESX Server and has some entries.

    KB said running 'arp - a' for a list of the ARP table.

    To do this, I need to open a service console. I have now read articles 3 or 4 on the use of the Service Console but I am still unable to open it to run the command. I do not understand what I am doing wrong, I am incredibly stupid or miss me something completely.

    An article said, press 'Alt F1"exactly where I am doing this? A virtual machine is connected to the ESX? An article said "to VIM summary screen' I tried logging on the virtual machine and point a web browser on the server, I get a screen of welcome of ESX with link"Connecting to Web Access", when I click on it I get"Internet Explorer Can t Open The Web page.

    I had a look at VIM, I can see the details of the Vswitch network on the configuration page, including the IP address of the console service. Can't see how to open a service console. VIM of pointing at the address for service console is unable to do anything.

    I just need to know how to open the Service console and check the tables of ARP based on the KB.

    Please dumb down of your responses to me!

    The fundamental problem is about some units of electric distribution that we use to power the equipment in the racks. They have a network connection which we track using Virtual Machines to the report of a third person of monitoring and control software. The virtual machines are running alarm software driver used to report to the third party. The virtual machine is on a blade server.

    We have a problem where a unit of the IML has been replaced but configured with incorrect default gateway address. In the hours to do so, the monitoring and control software lost connection to ILM and one by one, all units of the IML began to send the ARP requests - "who has 10.172.248.254'.

    Finally, the MDU constantly send ARP requests and the MDU have lost connectivity to the virtual computer. If we open the VM machine, follow up and a MUD, the ping command ping fails, if we put a laptop in place an ILM and ping the machine VM, the ping works fine.

    If power us off/on the ILM voltage they are good, but we are a 24/7 operation and power cycling the MDU is considered risky.

    We have had this problem before and the only solution was to rebuild the virtual machine and assign all MDU to a new network address.

    All switches ILM is connected (foundry Falstron GS) have been verified by the support of our network guys and we are told are all good. The blade server hosts about 20 VM and they work just fine from other systems SNMP traffic monitoring.

    If anyone has any ideas I'm all ears.

    Hello

    As stated, the console is the administration interface that you can use directly on the hardware. It is not a VM (as such) that connect you with the standard management GUI. You can SSH in the network or you can be "physically connected" as you say (I would use HP SIM or the ILO to connect directly to the blade). Once you have that screen upward, press 'Alt + F1' and you connect. Then you should be able to follow the KB to check the ARP table.

    See you soon,.

  • Newbie question: accessibility vs. insulation Service Console

    Hi all

    I wonder what people do in practice to balance isolate the service console/vCenter to be able to access essential services (updates, NTP, etc.) and to administer the host and vCenter.

    Quick reminder:

    Local government, not a department store. Just is about to go into production with ESX3.5/VC2.5, have licenses for the VDI which is one of the reasons why I'm not starting with v4. Had ESX in test for about a year.

    Network is a bit sophisticated, equipment Alcatel, can do VLAN etc., but managed by one other team so I didn't know very well how it can or can not do access control.

    Firewall is on the periphery of the network only; an inter - VLAN firewall or an ISA Server would be new for me, and probably ask a negotiation.

    Because I'm not quite yet in production, I know that my best chance now is to configure the network according to best practices. I have read the Security Hardening Guide, now I'm hoping to get some opinions 'the street '. Should I go the distance and set up a firewall, or can configure us a VLAN enough tight to be a good (if the second best) choice? What are the trade-offs of usability? How do you get updates if you do not connect that network to the Internet? All the creative solutions out there for the budget conscious?

    Thanks for your help,

    Jenna Flanagan

    City of Belmont COMPUTER service

    The service console is often regarded as the "keys to the Kingdom", if it is compromised, you have access to all the guests running.  the hardening guide is a very good starting point, an internal firewall would be a very good option there are several out there that are safe, but have a low learning curve, ISA is one, but there so smoothwall.

    However that said, even VLAN even though they are not considered as a security mechanism, should be used to separate your traffic, more important still is to separate traffic flows.  Make sure that your Service console and VMKernel traffic are separated from your Production comments traffic, this may be at the lowest level by exchanges and VLANs (not particularly sure, but better than nothing), moving to separate from Teddy and vSwitches and finally a game completely separated from pSwitches in order to guarantee a circulation independent flow (very safe but also very expensive.

    How many bears will you have in the comments. We're crazy.  with as little as 4 pNiICs you can start the design with real security in mind.

    vmnic0 + vmnic2-> traffic Service Console and VMKernel

    vmnic1 + vmnic3-> traffic Production comments.

    Very good Ed Haletky (Texiwill) reading series on the placement of NIC in design found here

    Now you are aware that the view output 4 is just around the corner, (guesstimated release date: mid November) this would introduce you to all the benefits of vSphere and use of VDI.  just a thought

    If you have found this device or any other answer useful please consider useful or correct buttons using attribute points

    Tom Howarth VCP / vExpert

    VMware communities user moderator

    Blog: www.planetvm.net

    Writer on "[vSphere of VMware and Virtual Infrastructure Security: securing ESX and virtual environment | ]. "[http://www.Amazon.co.uk/VMware-vSphere-Virtual-Infrastructure-Security/DP/0137158009/ref=sr_1_1?ie=UTF8&s=Books&qid=1256146240&SR=1-1].

  • Cannot access the Console remotely

    Hey guys, I'm new to VM Ware and has difficulties to access the console remotely, even if I can access the Web Access page very well...

    The error I get is:

    Unable to connect to the MKS: unable to connect to the host domain.com: no connection could be made because the target machine actively refused

    When you search for an answer to this, I found a post that said to ensure that the /etc/pam.d/vmware-authd has been configured correctly, as well as the/etc/vmware/config...

    None of these files/folders are there.

    That said, my host OS is (unfortunately) of Windows Vista, with VM Ware running on top of that, and now I am trying to get Fedora Core 11 to present itself as the virtual machine.

    Any ideas you can give would be much appreciated.

    Sorry, I did not myself clear - its port 902 on the host that you need to check that you can telnet to because the VMware console connections are made using the host (so that they can still operate even when there is no network in the comments, for example at installation time), not to the guest directly (for client firewalls are not the parameters used either for the console). I guess that 8333 is fine, otherwise you wouldn't be able to connect remotely to the web console.

    Guy Leech

    VMware vExpert 2009

    ---

    If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.

  • Adding user to access the Service Console via Putty

    Hi guys

    I'm quite new to the world of Vmware, so please exuse me if I look trivial.

    Basically, I want to create a user in order to access the service through PuTTY console.

    I tried with the root , but it says access denied. I have read the forums and I know that I need to create a new user, and then get to KNOW, but could you please tell me how and where I can create this user as I can only find Permissions tab for ESX1 (our esx server). What I need to for this to the service console physially enter the sever room or can I create this user using one of my domain accounts for VIC 2.5

    If I can do or could you please guide me further

    Also is it possible to use the service of the VIC, if so how.

    I would be very grateful if you could give me an answer for what I send the vizionsupport logs from the console using some of the linux (vmware controls), I think that I can do that by logging in on the ESX Server service console.

    Concerning

    Rucky

    To add a newuser you would do the following in the console of the ESX host.

    useradd username (where username is the name of the user account)

    passwd username (This will prompt you for the password for the user)

    Now this user must be able to connect via SSH

    You can then run su - (you will be prompted for the root password) that will put you in a root shell

    Also, you could edit/etc/ssh/sshd_config (using vi or nano)

    and change the following line

    Of

    PermitRootLogin not

    TO

    PermitRootLogin Yes

    type of service sshd restart (you should do this in the console) this will then allow you to ssh to the system as root.

  • Web Service remote access

    Hello

    Working locally I can access a web service with the following 2 files to the root of the directory, no maps, no configuration of the web service in the administrator:
    <!---/simpleTextConsume.cfm/--->

    < cfproperty >
    < name cffunction = "firstws" = "remote access" returntype = "string" >
    < cfreturn "Developer Center is awesome!" >
    < / cffunction >
    < / cfproperty >
    <!-simpleTextConsume.cfc /->
    < cfinvoke
    "WebService =" http://127.0.0.1:8500/cbweblatest/webservices/simpleText.cfc?wsdl "
    method = "firstws".
    returnvariable = "returnedText" >
    < / cfinvoke >

    < cfoutput >
    #variables.returnedText #.
    < / cfoutput >

    The error I get when I try to run http://www.myurl.com \webservices\simpleTextConsume.cfm is the following:
    /*____________________________________________________
    Could not generate objects stub for the call to the web service.
    Name: http://127.0.0.1:8500/cbweblatest/webservices/simpleText.cfc?wsdl. WSDL: http://127.0.0.1:8500/cbweblatest/webservices/simpleText.cfc?wsdl. org.xml.sax.SAXException: Fatal Error: URI = line 1 = null: next character must be ">" terminating comment...
    __________________________________________________*/

    I played a bit with you try to use a map and the creation of a Web service in admin, but get similar error, "cannot create.."

    The server in question is a linux based on virtual server, no Enterprise edition of CF 6.1, however, I'm using CF8 locally, all locally tested very well with the foregoing, also Flash datagrid with SQL test works fine locally.

    The foregoing does not not is a major, popular pointers.


    Colm

    It looks like a backslash oblique problem.

  • Remote access VPN users unable to see local lan or internet

    We implement an ASA5510. Now our users can connect to the vpn but cannot access the internal Lan or internet.

    Here is the config. Any help or idea would be greatly appreciated. Thank you

    Cryptochecksum: dd11079f e4fe7597 4a8657ba 1e7b287f

    : Saved
    : Written by enable_15 at 11:04:57.005 UTC Wednesday, April 22, 2015
    !
    ASA Version 9.0 (3)
    !
    CP-ASA-TOR1 hostname
    activate m.EmhnDT1BILmiAY encrypted password
    names of
    local pool CPRAVPN 10.10.60.1 - 10.10.60.40 255.255.255.0 IP mask
    !
    interface Ethernet0/0
    nameif outside
    security-level 0
    IP 63.250.109.211 255.255.255.248
    !
    interface Ethernet0/1
    nameif inside
    security-level 100
    10.10.10.254 IP address 255.255.255.0
    !
    interface Ethernet0/2
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Ethernet0/3
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Management0/0
    management only
    nameif management
    security-level 100
    IP 192.168.1.1 255.255.255.0
    !
    passive FTP mode
    the local object of net network
    10.10.10.0 subnet 255.255.255.0
    net remote object network
    10.10.1.0 subnet 255.255.255.0
    network of the NETWORK_OBJ_10.10.10.0_24 object
    10.10.10.0 subnet 255.255.255.0
    network of the NETWORK_OBJ_10.10.60.0_26 object
    255.255.255.192 subnet 10.10.60.0
    Outside_1_cryptomap to access extended list ip 10.10.10.0 allow 255.255.255.0 net object / distance
    CPRemoteVPN_splitTunnelAcl list standard access allowed 10.10.10.0 255.255.255.0
    pager lines 24
    Enable logging
    asdm of logging of information
    Outside 1500 MTU
    Within 1500 MTU
    management of MTU 1500
    no failover
    ICMP unreachable rate-limit 1 burst-size 1
    ASDM image disk0: / asdm-731 - 101.bin
    don't allow no asdm history
    ARP timeout 14400
    no permit-nonconnected arp
    NAT (inside, outside) local static source net net-local destination static net distance net-distance
    NAT (inside, outside) static source NETWORK_OBJ_10.10.10.0_24 NETWORK_OBJ_10.10.10.0_24 NETWORK_OBJ_10.10.60.0_26 NETWORK_OBJ_10.10.60.0_26 non-proxy-arp-search of route static destination
    !
    NAT (inside, outside) source after-service dynamic automatic one interface
    Route outside 0.0.0.0 0.0.0.0 63.250.109.209 1
    Timeout xlate 03:00
    Pat-xlate timeout 0:00:30
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    Floating conn timeout 0:00:00
    dynamic-access-policy-registration DfltAccessPolicy
    identity of the user by default-domain LOCAL
    Enable http server
    http 192.168.1.0 255.255.255.0 management
    http 10.10.10.0 255.255.255.0 inside
    No snmp server location
    No snmp Server contact
    Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
    Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
    Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
    Crypto ipsec ikev2 ipsec-proposal OF
    encryption protocol esp
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 proposal ipsec 3DES
    Esp 3des encryption protocol
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 ipsec-proposal AES
    Esp aes encryption protocol
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 ipsec-proposal AES192
    Protocol esp encryption aes-192
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 AES256 ipsec-proposal
    Protocol esp encryption aes-256
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec pmtu aging infinite - the security association
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
    card crypto Outside_map 1 corresponds to the address Outside_1_cryptomap
    card crypto Outside_map 1 set pfs Group1
    card crypto Outside_map 1 set peer 209.171.34.91
    card crypto Outside_map 1 set transform-set ESP-3DES-SHA ikev1
    card crypto Outside_map 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
    card crypto Outside_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
    Outside_map interface card crypto outside
    trustpool crypto ca policy
    IKEv2 crypto policy 1
    aes-256 encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 10
    aes-192 encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 20
    aes encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 30
    3des encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 40
    the Encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    Crypto ikev1 allow outside
    IKEv1 crypto policy 10
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    Telnet timeout 5
    SSH timeout 5
    Console timeout 0
    management of 192.168.1.2 - dhcpd address 192.168.1.254
    enable dhcpd management
    !
    a basic threat threat detection
    Statistics-list of access threat detection
    no statistical threat detection tcp-interception
    internal CPRemoteVPN group strategy
    attributes of Group Policy CPRemoteVPN
    Server DNS 10.10.10.12 value
    L2TP ipsec VPN-tunnel-Protocol ikev1, ikev2
    value of Split-tunnel-network-list CPRemoteVPN_splitTunnelAcl
    carepath.local value by default-field
    Split-dns value carepath.ca
    activate dns split-tunnel-all
    no method of MSIE-proxy-proxy
    the address value CPRAVPN pools
    roys jjiV7E.dmZNdBlFQ encrypted password privilege 0 username
    roys username attributes
    VPN-group-policy CPRemoteVPN
    tunnel-group 209.171.34.91 type ipsec-l2l
    IPSec-attributes tunnel-group 209.171.34.91
    IKEv1 pre-shared-key *.
    type tunnel-group CPRemoteVPN remote access
    attributes global-tunnel-group CPRemoteVPN
    address CPRAVPN pool
    Group Policy - by default-CPRemoteVPN
    IPSec-attributes tunnel-group CPRemoteVPN
    IKEv1 pre-shared-key *
    !
    class-map inspection_default
    match default-inspection-traffic
    !
    !
    type of policy-card inspect dns preset_dns_map
    parameters
    maximum message length automatic of customer
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the preset_dns_map dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    inspect the rsh
    inspect the rtsp
    inspect esmtp
    inspect sqlnet
    inspect the skinny
    inspect sunrpc
    inspect xdmcp
    inspect the sip
    inspect the netbios
    inspect the tftp
    Review the ip options
    !
    global service-policy global_policy
    context of prompt hostname
    no remote anonymous reporting call
    Cryptochecksum:dd11079fe4fe75974a8657ba1e7b287f

    : end

    Hello

    A couple of things set this:

    -crypto isakmp nat-traversal 20

    -management-access inside

    Can you run a packet tracer and attach it here, to see what are the phases that crosses the package.

    David Castro,

    Concerning

Maybe you are looking for