Remote access VPN clients

Hello

I've set up IPSec VPN remotely and it works fine. I need access to connected VPN clients, and it does not work. I have already added an entry to traffic allowing sheep ACL from inside my network to the VPN.

More information:

Inside of the net: 10.1.1.0/24

Pool VPN: 172.30.1.0/24

Is it possible to access from my internal network to the VPN users?

Thanks in advance.

Best regards.

Marcelo

VPN users have access to certain servers via the list of Tunnel from Split.

Marcelo,

Split tunnel ACLs must be an IP acl, it is not recommended and supported to set the TCP ports on the split tunnel ACL, the vpn client don't interpret this ACl as a lot are interested in IP, TCP ports, and that could cause you a problem. You can change your config to reflect this. Regarding ACL split tunnel, it must contain the server line. networks that this vpn, customers arrive, remind you this is two-way, as you know.

So if IT supports the IP range is on this vpnExample ACL vpn clients will be able to reach the IT support guys and vice versa.

I advise you to change your split tunnel ACLs to specific ports to only the desired servers and the presenters what these customers need to achieve.

Remove the ports out of this Split tunnel ACLs.

If you need to restrict services for vpn rather clients use VPN filters.

http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00808c9a87.shtml

Tags: Cisco Security

Similar Questions

  • Configure ASA5055 as a remote access VPN client

    Hello world

    I'm trying to configure a 5505 as a remote access VPN client. I have several old hubs VPN 3002, but in the new sites I'll use a 5505 instead of these 3002.

    I think that the configuration is very simple. I have the IP address of the peer (remote server), I know it is an IPsec tunnel without certificate and I have passwords and user name and group.

    How can I translate this configuration for an ASA5505? I have attached a screenshot.

    Here ya go:

    http://www.Cisco.com/en/us/docs/security/ASA/asa83/configuration/guide/ezvpn505.html

    Federico.

  • How to prohibit remote access vpn client to use the local DNS server

    Hello

    I'm on ASA5505 remote access vpn configuration.

    Everything works fine so far, except when the client got connected, he always used the local DNS server provided by the ISP.  How can I force the customer to use the DNS server configured on ASA?

    Thank you.

    Kind regards

    The command "Activate dns split-tunnel-all" is supported only on SSL VPN and VPN IKEv2. Since you're using IKEv1, this command is not supported.

    Here's the order reference:

    http://www.Cisco.com/en/us/docs/security/ASA/asa82/command/reference/S8.html#wp1533793

    You configure no split tunnel? If you are, then you need to configure "tunnelall" split tunnel policy, and that will force the dns resolution and everything else through the VPN tunnel.

  • Connected to the Internet of VPN remote access VPN clients

    Greetings,

    I need to remote VPN clients to connect to the Internet from the same server VPN ASA

    "client connects to ASA the external interface VPN tunnel can access Internet from the same external interface ASA new."

    Thank you

    you need to configure "same-security-traffic permit intra-interface" on the SAA.

    Also, need to configure the relevant statements of nat for your range of pool of customers.

    i.e.

    Global 1 interface (outside)

    NAT (outside) 1 access-list anyconnectacl

    where anyconnectacl is the pool for your customers:

    permit ip 172.16.1.0 access list anyconnectacl 255.255.255.0 any

  • Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network

    I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well

    Thank you

    interface Ethernet0/0

    Speed 100

    full duplex

    nameif outside

    security-level 0

    IP x.x.x.x 255.255.255.240

    !

    interface Ethernet0/1

    Speed 100

    full duplex

    nameif inside

    security-level 100

    IP 10.88.10.254 255.255.255.0

    !

    interface Management0/0

    Shutdown

    nameif management

    security-level 0

    no ip address

    !

    permit same-security-traffic inter-interface

    permit same-security-traffic intra-interface

    network of the PAT_to_Outside_ClassA object

    10.88.0.0 subnet 255.255.0.0

    network of the PAT_to_Outside_ClassB object

    subnet 172.16.0.0 255.240.0.0

    network of the PAT_to_Outside_ClassC object

    Subnet 192.168.0.0 255.255.240.0

    network of the LocalNetwork object

    10.88.0.0 subnet 255.255.0.0

    network of the RemoteNetwork1 object

    Subnet 192.168.0.0 255.255.0.0

    network of the RemoteNetwork2 object

    172.16.10.0 subnet 255.255.255.0

    network of the RemoteNetwork3 object

    10.86.0.0 subnet 255.255.0.0

    network of the RemoteNetwork4 object

    10.250.1.0 subnet 255.255.255.0

    network of the NatExempt object

    10.88.10.0 subnet 255.255.255.0

    the Site_to_SiteVPN1 object-group network

    object-network 192.168.4.0 255.255.254.0

    object-network 172.16.10.0 255.255.255.0

    object-network 10.0.0.0 255.0.0.0

    outside_access_in deny ip extended access list a whole

    inside_access_in of access allowed any ip an extended list

    11 extended access-list allow ip 10.250.1.0 255.255.255.0 any

    outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1

    mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool

    NAT static NatExempt NatExempt of the source (indoor, outdoor)

    NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search

    NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1

    NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2

    NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3

    NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search

    !

    network of the PAT_to_Outside_ClassA object

    NAT dynamic interface (indoor, outdoor)

    network of the PAT_to_Outside_ClassB object

    NAT dynamic interface (indoor, outdoor)

    network of the PAT_to_Outside_ClassC object

    NAT dynamic interface (indoor, outdoor)

    Access-group outside_access_in in interface outside

    inside_access_in access to the interface inside group

    Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1

    dynamic-access-policy-registration DfltAccessPolicy

    Sysopt connection timewait

    Service resetoutside

    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

    Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series

    Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

    Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

    Crypto-map dynamic dynmap 10 set pfs

    Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1

    life together - the association of security crypto dynamic-map dynmap 10 28800 seconds

    Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000

    Crypto-map dynamic dynmap 10 the value reverse-road

    card crypto mymap 1 match address outside_1_cryptomap

    card crypto mymap 1 set counterpart x.x.x.x

    card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1

    card crypto mymap 86400 seconds, 1 lifetime of security association set

    map mymap 1 set security-association life crypto kilobytes 4608000

    map mymap 100-isakmp ipsec crypto dynamic dynmap

    mymap outside crypto map interface

    crypto isakmp identity address

    Crypto isakmp nat-traversal 30

    Crypto ikev1 allow outside

    IKEv1 crypto ipsec-over-tcp port 10000

    IKEv1 crypto policy 5

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 10

    preshared authentication

    3des encryption

    sha hash

    Group 1

    life 86400

    IKEv1 crypto policy 50

    preshared authentication

    the Encryption

    md5 hash

    Group 2

    life 86400

    IKEv1 crypto policy 60

    preshared authentication

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 70

    preshared authentication

    aes-256 encryption

    sha hash

    Group 1

    life 86400

    IKEv1 crypto policy 90

    preshared authentication

    aes encryption

    sha hash

    Group 2

    life 86400

    Telnet timeout 5

    Console timeout 0

    management-access inside

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    internal BACKDOORVPN group policy

    BACKDOORVPN group policy attributes

    value of VPN-filter 11

    Ikev1 VPN-tunnel-Protocol

    Split-tunnel-policy tunnelall

    BH.UK value by default-field

    type tunnel-group BACKDOORVPN remote access

    attributes global-tunnel-group BACKDOORVPN

    address pool Admin_Pool

    Group Policy - by default-BACKDOORVPN

    IPSec-attributes tunnel-group BACKDOORVPN

    IKEv1 pre-shared-key *.

    tunnel-group x.x.x.x type ipsec-l2l

    tunnel-group ipsec-attributes x.x.x.x

    IKEv1 pre-shared-key *.

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns preset_dns_map

    parameters

    maximum message length automatic of customer

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the preset_dns_map dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the rsh

    inspect the rtsp

    inspect esmtp

    inspect sqlnet

    inspect the skinny

    inspect sunrpc

    inspect xdmcp

    inspect the sip

    inspect the netbios

    inspect the tftp

    Review the ip options

    !

    global service-policy global_policy

    Excellent.

    Evaluate the useful ticket.

    Thank you

    Rizwan James

  • Remote access VPN Client to PIX, DNS issue

    Hi all.  I searched on this, but I can't find my answer.

    I set up a VPN connection to a PIX Firewall (running the version 8.0 (4)) for my business.  The VPN connection works correctly, in that I can connect to it using my software (v 5.0.02.0090) Cisco VPN Client and ping servers/resources internal IP address. However, if I try to ping by host name, it does not resolve to an IP address.  If I open a command prompt on my PC and type ipconfig/all, there are no DNS servers for my VPN, just for my normal Intel NIC adapter - I think I should have a DNS server listed under the map of VPN, right?  Here is the relevant (I think) for the VPN config lines:

    8.0 (4) version PIX

    domain xx.xx

    DNS lookup field inside

    DNS server-group DefaultDNS

    Server name 192.168.20.23

    domain xx.xx

    IP local pool vpnpoolIT 10.10.8.2 - 10.10.8.254 mask 255.255.255.0

    Crypto ipsec transform-set esp-3des esp-md5-hmac FirstSet

    Crypto-map dynamic dyn1 1jeu transform-set FirstSet

    Crypto-map dynamic dyn1 1 lifetime of security association set seconds 28800

    Crypto-map dynamic dyn1 kilobytes of life 1 set security-association 4608000

    crypto ISAKMP policy 1

    preshared authentication

    3des encryption

    md5 hash

    Group 2

    life 86400

    tunnel-group ITGroup type remote access

    tunnel-group ITGroup General attributes

    address vpnpoolIT pool

    Group-RADIUS authentication server

    tunnel-group ITGroup ipsec-attributes

    pre-shared-key *.

    Am I missing?  I can solve the DNS on the PIX itself requests.

    All the info I can find online is for an older version of the PIX software which says that I should enter the vpngroup dns- IP address of the server command, but this command is not available in my version of the software.

    Hello

    To set a DNS server to be injected into the VPN clients when they connect, you can do the following:

    This is the tunnel-group where lands the remote connection:

    tunnel-group ITGroup type remote access

    tunnel-group ITGroup General attributes

    address vpnpoolIT pool

    Group-RADIUS authentication server

    tunnel-group ITGroup ipsec-attributes

    pre-shared-key *.

    For example, create a group policy:

    internal VPN group policy
    attributes of VPN group policy

    DNS value--> x.x.x.x where x.x.x.x is the IP address of the DNS server

    Then, apply the group policy for the Group of tunnel:

    tunnel-group ITGroup General attributes

    Group Policy - by default-VPN

    It will be useful.

    Federico.

  • DMVPN with based remote access VPN client

    Hi all

    We DMVPN deployed to connect to our remote location now I want to configure the vpn remote access also with DMVPN tunnel so if somehow our DMVPN tunnel goes down we can connect to the router through vpn remote access client based around... I want experts to do the light on it is it possible or what are the technical challenges that I have to face in this regard.

    Thank you

    Salman Jamshed

    Hello Salman,

    It's 100% possible, there is no harm in having them both up on your router.

    In fact, as you have said that it will provide an extra layer of redundancy if by chance the DMVPN tunnel breaks down.

    That being said, you can go ahead and do it is a movement course

    Julio

  • Remote access VPN client to connect but cannot ping inside the host, after that split tunnel is activated (config-joint)

    Hello

    I don't know what could be held, vpn users can ping to the outside and inside of the Cisco ASA interface but can not connect to servers or servers within the LAN ping.

    is hell config please kindly and I would like to know what might happen.

    hostname horse

    domain evergreen.com

    activate 2KFQnbNIdI.2KYOU encrypted password

    2KFQnbNIdI.2KYOU encrypted passwd

    names of

    ins-guard

    !

    interface GigabitEthernet0/0

    LAN description

    nameif inside

    security-level 100

    192.168.200.1 IP address 255.255.255.0

    !

    interface GigabitEthernet0/1

    Description CONNECTION_TO_FREEMAN

    nameif outside

    security-level 0

    IP 196.1.1.1 255.255.255.248

    !

    interface GigabitEthernet0/2

    Description CONNECTION_TO_TIGHTMAN

    nameif backup

    security-level 0

    IP 197.1.1.1 255.255.255.248

    !

    interface GigabitEthernet0/3

    Shutdown

    No nameif

    no level of security

    no ip address

    !

    interface Management0/0

    Shutdown

    No nameif

    no level of security

    no ip address

    management only

    !

    boot system Disk0: / asa844-1 - k8.bin

    boot system Disk0: / asa707 - k8.bin

    passive FTP mode

    clock timezone WAT 1

    DNS server-group DefaultDNS

    domain green.com

    network of the NETWORK_OBJ_192.168.2.0_25 object

    Subnet 192.168.2.0 255.255.255.128

    network of the NETWORK_OBJ_192.168.202.0_24 object

    192.168.202.0 subnet 255.255.255.0

    network obj_any object

    subnet 0.0.0.0 0.0.0.0

    the DM_INLINE_NETWORK_1 object-group network

    object-network 192.168.200.0 255.255.255.0

    object-network 192.168.202.0 255.255.255.0

    the DM_INLINE_NETWORK_2 object-group network

    object-network 192.168.200.0 255.255.255.0

    object-network 192.168.202.0 255.255.255.0

    access-list extended INSIDE_OUT allow ip 192.168.202.0 255.255.255.0 any

    access-list extended INSIDE_OUT allow ip 192.168.200.0 255.255.255.0 any

    Access extensive list permits all ip a OUTSIDE_IN

    gbnlvpntunnel_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0

    standard access list gbnlvpntunnel_splitTunnelAcl allow 192.168.202.0 255.255.255.0

    gbnlvpntunnell_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0

    standard access list gbnlvpntunnell_splitTunnelAcl allow 192.168.202.0 255.255.255.0

    pager lines 24

    Enable logging

    asdm of logging of information

    Within 1500 MTU

    Outside 1500 MTU

    backup of MTU 1500

    mask of local pool VPNPOOL 192.168.2.0 - 192.168.2.100 IP 255.255.255.0

    no failover

    ICMP unreachable rate-limit 1 burst-size 1

    ASDM image disk0: / asdm-645 - 206.bin

    don't allow no asdm history

    ARP timeout 14400

    NAT (inside, outside) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

    NAT (inside, backup) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

    NAT (inside, outside) static source DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

    NAT (inside, backup) static source DM_INLINE_NETWORK_2 DM_INLINE_NETWORK_2 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination

    !

    network obj_any object

    dynamic NAT interface (inside, backup)

    Access-group interface inside INSIDE_OUT

    Access-group OUTSIDE_IN in interface outside

    Route outside 0.0.0.0 0.0.0.0 196.1.1.2 1 track 10

    Route outside 0.0.0.0 0.0.0.0 197.1.1.2 254

    Timeout xlate 03:00

    Pat-xlate timeout 0:00:30

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    Floating conn timeout 0:00:00

    dynamic-access-policy-registration DfltAccessPolicy

    identity of the user by default-domain LOCAL

    Enable http server

    http 192.168.200.0 255.255.255.0 inside

    http 192.168.202.0 255.255.255.0 inside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    monitor SLA 100

    type echo protocol ipIcmpEcho 212.58.244.71 interface outside

    Timeout 3000

    frequency 5

    monitor als 100 calendar life never start-time now

    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

    Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    outside_map interface card crypto outside

    backup_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    backup of crypto backup_map interface card

    Crypto ikev1 allow outside

    Crypto ikev1 enable backup

    IKEv1 crypto policy 10

    authentication crack

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 20

    authentication rsa - sig

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 30

    preshared authentication

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 40

    authentication crack

    aes-192 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 50

    authentication rsa - sig

    aes-192 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 60

    preshared authentication

    aes-192 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 70

    authentication crack

    aes encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 80

    authentication rsa - sig

    aes encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 90

    preshared authentication

    aes encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 100

    authentication crack

    3des encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 110

    authentication rsa - sig

    3des encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 120

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 130

    authentication crack

    the Encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 140

    authentication rsa - sig

    the Encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 150

    preshared authentication

    the Encryption

    sha hash

    Group 2

    life 86400

    !

    track 10 rtr 100 accessibility

    Telnet 192.168.200.0 255.255.255.0 inside

    Telnet 192.168.202.0 255.255.255.0 inside

    Telnet timeout 5

    SSH 192.168.202.0 255.255.255.0 inside

    SSH 192.168.200.0 255.255.255.0 inside

    SSH 0.0.0.0 0.0.0.0 outdoors

    SSH timeout 15

    SSH group dh-Group1-sha1 key exchange

    Console timeout 0

    management-access inside

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    internal group vpntunnel strategy

    Group vpntunnel policy attributes

    Ikev1 VPN-tunnel-Protocol

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list vpntunnel_splitTunnelAcl

    field default value green.com

    internal vpntunnell group policy

    attributes of the strategy of group vpntunnell

    Ikev1 VPN-tunnel-Protocol

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list gbnlvpntunnell_splitTunnelAcl

    field default value green.com

    Green user name encrypted BoEFKkDtbnX5Uy1Q privilege 15 password

    attributes of user name THE

    VPN-group-policy gbnlvpn

    tunnel-group vpntunnel type remote access

    tunnel-group vpntunnel General attributes

    address VPNPOOL pool

    strategy-group-by default vpntunnel

    tunnel-group vpntunnel ipsec-attributes

    IKEv1 pre-shared-key *.

    type tunnel-group vpntunnell remote access

    tunnel-group vpntunnell General-attributes

    address VPNPOOL2 pool

    Group Policy - by default-vpntunnell

    vpntunnell group of tunnel ipsec-attributes

    IKEv1 pre-shared-key *.

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns migrated_dns_map_1

    parameters

    maximum message length automatic of customer

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the migrated_dns_map_1 dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the rsh

    inspect the rtsp

    inspect esmtp

    inspect sqlnet

    inspect the skinny

    inspect sunrpc

    inspect xdmcp

    inspect the sip

    inspect the netbios

    inspect the tftp

    Review the ip options

    !

    global service-policy global_policy

    context of prompt hostname

    no remote anonymous reporting call

    call-home

    Profile of CiscoTAC-1

    no active account

    http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

    email address of destination [email protected] / * /

    destination-mode http transport

    Subscribe to alert-group diagnosis

    Subscribe to alert-group environment

    Subscribe to alert-group monthly periodic inventory

    monthly periodicals to subscribe to alert-group configuration

    daily periodic subscribe to alert-group telemetry

    Cryptochecksum:7c1b1373bf2e2c56289b51b8dccaa565

    Hello

    1 - Please run these commands:

    "crypto isakmp nat-traversal 30.

    "crypto than dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 Road opposite value.

    The main issue here is that you have two roads floating and outside it has a better than backup metric, that's why I added the command 'reverse-road '.

    Please let me know.

    Thank you.

  • remote access VPN not connected - no access inside

    Hi, I have successfully configured remote access VPN router, it is connected, but no access to the inside, none of my ip addresses. I do not know SPLIT_ACL is ok and I've denied NATting them. For me, everything is ok. I did a lot in ASA, without anyproblem. Thanks for the comments.

    enable secret 5 $1$ y0AJ$ rhrjbrpe5NDiAyHGlfeNi.

    !

    AAA new-model

    !

    !

    AAA authentication login bcc_users local

    AAA authorization bcc_group LAN

    !

    crypto ISAKMP policy 10

    BA aes

    preshared authentication

    Group 2

    !

    ISAKMP crypto client configuration group ra_vpn_bcc

    key *.

    DNS 8.8.8.8

    bcc.local field

    pool vpn_pool

    ACL SPLIT_ACL

    Max-users 7

    netmask 255.255.255.0

    !

    !

    Crypto ipsec transform-set RIGHT aes - esp esp-sha-hmac

    tunnel mode

    !

    !

    !

    Crypto-map dynamic dynmap 10

    Set transform-set RIGHT

    market arriere-route

    !

    !

    card crypto client CRYPTO_VPN of authentication list bcc_users

    card crypto isakmp authorization list bcc_group CRYPTO_VPN

    crypto card for the CRYPTO_VPN client configuration address respond

    map CRYPTO_VPN 10-isakmp ipsec crypto dynamic dynmap

    !

    !

    interface GigabitEthernet0/0/4

    IP address %.

    NAT outside IP

    auto negotiation

    BFD interval 50 50 5 min_rx multiplier

    card crypto CRYPTO_VPN

    !

    !

    IP local pool vpn_pool 172.31.255.0 172.31.255.250

    NAT extended IP access list

    deny ip 10.0.0.0 0.255.255.255 172.31.255.0 0.0.0.255

    deny ip 172.16.0.0 0.0.255.255 172.31.255.0 0.0.0.255

    deny ip 192.168.0.0 0.0.255.255 172.31.255.0 0.0.0.255

    IP address 172.16.0.0 allow 0.15.255.255 all

    IP 192.168.0.0 allow 0.0.255.255 everything

    IP 10.0.0.0 allow 0.255.255.255 everything

     

    SPLIT_ACL extended IP access list

    IP 10.0.0.0 allow 0.255.255.255 172.31.255.0 0.0.0.255

    IP address 172.16.0.0 allow 0.0.255.255 172.31.255.0 0.0.0.255

    IP 192.168.0.0 allow 0.0.255.255 172.31.255.0 0.0.0.255

    Take a look at the delivery.

    You do not have a route to the VPN pool on a nearby device.

  • Configuring remote access VPN

    Hi all

    I need help with remote access vpn configuration. I want to some remote users who have access to the internet on their system to connect and access an application server in my seat social cisco vpn client user. I use Cisco 881. I am unable to use the SDM configuration because it seems that SDM is not supported by the router so I'm using command line. I'd appreciate any help I can get. Thank you.

    This is the configuration I have:

    VPNROUT #sho run
    Building configuration...

    Current configuration: 6832 bytes
    !
    ! Last configuration change at 10:50:45 UTC Saturday, May 30, 2015, by thomas
    version 15.2
    no service button
    horodateurs service debug datetime msec
    Log service timestamps datetime msec
    no password encryption service
    !
    hostname VPNROUT
    !
    boot-start-marker
    boot-end-marker
    !
    !
    logging buffered 51200 warnings
    !
    AAA new-model
    !
    !
    AAA authentication login default local
    AAA authentication login userauthen1 local
    AAA authorization groupauthor1 LAN
    !
    !
    !
    !
    !
    AAA - the id of the joint session
    iomem 10 memory size
    !
    Crypto pki trustpoint TP-self-signed-1632305899
    enrollment selfsigned
    name of the object cn = IOS - Self - signed - certificate - 1632305899
    revocation checking no
    rsakeypair TP-self-signed-1632305899
    !
    !
    TP-self-signed-1632305899 crypto pki certificate chain
    certificate self-signed 01
    3082022B 30820194 02020101 300 D 0609 2A 864886 F70D0101 05050030 A0030201
    2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
    69666963 31363332 33303538 6174652D 3939301E 170 3134 30313233 31323132
    33325A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
    4F532D53 5369676E 656C662D 43 65727469 66696361 74652 31 36333233 65642D
    30353839 3930819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
    8100BC0C 341CD79B A38572CE 1F0F9A91 F96B133C A889B564 E8352034 1CF5EE4B
    B505616B 6014041B EC498C0A F6C5CD2B F5BF62DA BD6E1C44 0C7B9089 1FD0C6E5
    299CEB40 28CD3F3B ADE3468A B07AAA9F AC42F0A7 4087172A 33C4013D 9A50884D
    5778727E 53A4940E 6E622460 560C F597DD53 3B 261584 E45E8776 A848B73D 5252
    92 50203 010001A 3 53305130 1 130101 FF040530 030101FF 301F0603 0F060355 D
    551 2304 18301680 14E85AD0 DEF133D8 E09516FD 0AA5FDAD E10EAB1A FA301D06
    03551D0E E85AD0DE 04160414 F133D8E0 9516FD0A A5FDADE1 0EAB1AFA 300 D 0609
    2A 864886 818100A 5 05050003 5B23ED5B 9A380E1F 467ABB03 BAB1070B F70D0101
    7A 218377 73089DC1 D32DA585 C5FD7ECE 0D000F96 7F3AB6CC 71509E8F 3F1C55AE
    E37536A3 1008FBF9 A29329D5 6F76DDC0 AA1C70AE 958AAE5D 32388BE4 2C1C6839
    0369 D 533 027B612C 8D199C35 C008FE00 F7E1DF62 9C73E603 85C3240A 63611D 93
    854A61E2 794F8EF5 DA535DCC B209DA
    quit smoking
    !
    !
    !
    no record of conflict ip dhcp
    DHCP excluded-address IP 10.10.10.1
    DHCP excluded-address IP 172.20.0.1 172.20.0.50
    !
    DHCP IP CCP-pool
    import all
    Network 10.10.10.0 255.255.255.248
    default router 10.10.10.1
    Rental 2 0
    !
    IP dhcp pool 1
    network 172.20.0.0 255.255.240.0
    domain meogl.net
    router by default - 172.20.0.1
    172.20.0.4 DNS server 41.79.4.11 4.2.2.2 8.8.8.8
    8 rental
    !
    !
    !
    no ip domain search
    IP domain name meogl.net
    name of the IP-server 172.20.0.4
    name of the IP-server 41.79.4.11
    IP-server names 4.2.2.2
    8.8.8.8 IP name-server
    IP cef
    No ipv6 cef
    !
    !
    license udi pid CISCO881-K9 sn FCZ1804C3SL
    !
    !
    username secret privilege 15 thomas 4 JXSizd1r/hMqPpGz94vKBb5somtpZLy03k50rJvHO6c
    username privilege 15 secret 4 mowe hlfv/rdDRCAeTUzRXbOIfdaKhJCl1onoGdaQeaQsAnw
    !
    !
    !
    !
    !
    !
    !
    crypto ISAKMP policy 1
    BA 3des
    preshared authentication
    Group 2
    !
    ISAKMP crypto client configuration group moweclients
    XXXXXXX key
    DNS 172.20.0.4
    meogl.net field
    pool mowepool
    !
    !
    Crypto ipsec transform-set esp-3des esp-sha-hmac moweset
    tunnel mode
    !
    !
    !
    Dynmap crypto dynamic-map 1
    Set transform-set moweset
    market arriere-route
    !
    !
    card crypto client mowemap of authentication list userauthen1
    card crypto isakmp authorization list groupauthor1 mowemap
    client configuration address card crypto mowemap answer
    mowemap 1 card crypto ipsec-isakmp dynamic dynmap
    !
    !
    !
    !
    !
    interface Loopback0
    IP 172.30.30.1 255.255.255.0
    IP nat inside
    IP virtual-reassembly in
    !
    interface FastEthernet0
    no ip address
    !
    interface FastEthernet1
    no ip address
    !
    interface FastEthernet2
    switchport access vlan 100
    no ip address
    !
    interface FastEthernet3
    no ip address
    !
    interface FastEthernet4
    IP 41.7.8.13 255.255.255.252
    NAT outside IP
    IP virtual-reassembly in
    intellectual property policy map route VPN-CLIENT
    Shutdown
    automatic duplex
    automatic speed
    mowemap card crypto
    !
    interface Vlan1
    Description $ETH_LAN$
    IP 10.10.10.1 255.255.255.248
    IP tcp adjust-mss 1452
    !
    interface Vlan100
    IP 172.20.0.1 255.255.240.0
    IP nat inside
    IP virtual-reassembly in
    !
    local pool IP 192.168.1.1 mowepool 192.168.1.100
    IP forward-Protocol ND
    IP http server
    23 class IP http access
    local IP http authentication
    IP http secure server
    IP http timeout policy slowed down 60 life 86400 request 10000
    !
    IP nat inside source overload map route interface FastEthernet4 LAT
    IP route 0.0.0.0 0.0.0.0 41.7.8.12
    !
    access-list 23 allow 10.10.10.0 0.0.0.7
    access-list 23 allow 172.20.0.0 0.0.15.255
    access-list 100 permit ip 172.20.0.0 0.0.15.255 everything
    access-list 144 allow ip 192.168.1.0 0.0.0.255 any
    not run cdp
    !
    LAT route map permit 1
    corresponds to the IP 100
    IP 41.7.8.12 jump according to the value
    !
    route VPN-CLIENT map permit 1
    corresponds to the IP 144
    !
    Line con 0
    no activation of the modem
    line to 0
    line vty 0 4
    access-class 23 in
    privilege level 15
    transport input telnet ssh
    line vty 5 15
    access-class 23 in
    privilege level 15
    transport input telnet ssh
    !
    !
    end

    Please the configuration above, give me the desired output.

    Thank you.

    Hello Thomas,.

    I'm glad to hear that you have found useful in the example configuration.

    I checked your configuration and everything seems ok with him, especially the statements of nat.

     ip local pool mowepool 192.168.1.1 192.168.1.100 access-list 100 deny ip 172.20.0.0 0.0.15.255 192.168.1.0 0.0.0.255 access-list 100 permit ip 172.20.0.0 0.0.15.255 any route-map LAT permit 1 match ip address 100 ip nat inside source route-map LAT interface FastEthernet4 overload interface Vlan100 ip address 172.20.0.1 255.255.240.0 ip nat inside ip virtual-reassembly in 

    Try to generate ICMP traffic behind your 100 VLANS to the client VPN in order to answer the following questions:

    -The router receives this traffic between VLAN100 unit?

    -The router is encrypt this traffic, after receiving the ICMP packet?

    #show crypto ipsec router its can help you with this question. Look for the program/decaps counters.

    -The same, but the other way around (from VPN client to device behind VLAN100) try to locate the problem.

    The following document explains more this crypto commands and debugs if necessary.

    http://www.Cisco.com/c/en/us/support/docs/security-VPN/IPSec-negotiation-IKE-protocols/5409-IPSec-debug-00.html#iosdbgs

  • PIX 515E and remote access VPN

    I use a PIX 515E with: ASDM Version: 5,0000 51 PIX Version: 8.0 (4) and configure it with remote access VPN.

    I would like to get an email every time that a user login (and or disconnection) to the VPN. Remote clients use the Cisco VPN Client.

    Any help is appreciated,

    Hello

    Here is a link to the email configuration when you log in to the ASA/PIX: http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/63884-config-asa-00.html#anc7

    Then you can create a list of message to send the logs only for the connection/disconnection of the VPN user: http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/63884-config-asa-00.html#anc18

    There is a wire that is linked here: https://supportforums.cisco.com/discussion/10798976/asa-email-logging-issue

  • Remote access VPN fails after upgrading to 8.04

    Hello:

    Sorry if this has been posted, but I couldn't find it anywhere.

    After the upgrade of my 2 of my 5510 s to 8.04, my remote access VPN does not work. I can connect via Radius without problem. Once connected, I can't do anything on the network. When I try to telnet to any device, I get a white screen with no response. As it is to find the device but it does not. E-mail, intranet, nothing works. Seems to be time. I tried to upgrade to the latest version of Windows Client, still no go.

    Everyone knows this at all? Any help appreciated.

    TIA,

    Brad

    I saw the same problem after upgrading to 8.0.4. And it is caused by the "IP Compression" option enabled in group policy. After deactivation, it works. Cisco has just completed this bug recently:

    http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsu26649

    Zhenning

  • Road of default remote access VPN session

    ASA version 8.2.2

    How do you assign remote access VPN sessions a single default route?  Other than the default route assigned to ASA.  For example, my VPN ASA (handles vpn sessions), defaults to the Internet.  I wish that sessions VPN for remote access by default internal network first, then follow the default route to the Internet on another firewall.

    The SAA outside the IP address of the interface is a public.  Inside is a private 10.x.x.x.  VPN clients receive 172.17.x.x.

    Thank you

    After the command 'road' added keyword "tunnel".

    in the tunnel

    Specifies the route as the default gateway of tunnel for the VPN traffic.

    http://www.Cisco.com/en/us/docs/security/ASA/asa80/command/reference/QR.html#wp1767323

  • Remote access VPN pix version 8.0 (3)

    Hi all

    First of all, I would like to thank to all members of the forum who got help in several messages on the configuration of the pix 515.

    I am now configuring remote VPN access with radius authentication to my network, but I can't connect.

    I use the cisco vpn client 5.0.03.0560, I have also tested my pix radius (inside) server authentication and works very well.

    I already tried to retype the key of the cli, but I still can't remote access vpn to work.

    I also tried to create another remote vpn with another name and local authentication, but I have the same problem.

    I use 8.0 (3) version pix.

    Can someone help me

    I attach the log file of the cisco vpn client to help solve the problem, as well a configuration of the pix folder.

    Thank you very much in advance and I seek prior information.

    http://www.Cisco.com/en/us/docs/security/ASA/asa72/configuration/guide/vpnadd.html#wp999516

    [Pls RATE if HELP]

  • Service of ASA module does on 6509-E support remote access VPN?

    I'm having a problem of configuration of remote access VPN (SSL, Anyconnect ect.) on the Module of ASA Service on 6509-E. It is even supported or I'm wasting my time trying to do something that won't work in a first place :) to work? Site-to-Site works without any problem.

    Technical info:

    6509-E current SUP 2 t SY 15.1 (2)

    Module of ASA - WS-SVC-ASA-SM1 running of the image - asa912-smp-k8 & asdm-712

    Licenses on ASA:

    Encryption--Activated

    3DES-AES-Encryption - enabled

    Thank you for the support.

    You run multiple context mode?

    If you are, access remote VPN only is not supported in this case:

    "Note several context mode only applies to the IKEv2 and IKEv1 site to another and applies not to the AnyConnect, clientless SSL VPN, the legacy Cisco VPN, native VPN client client of Apple, the VPN client from Microsoft or cTCP for IKEv1 IPsec."

    Reference.

Maybe you are looking for