remote access VPN not connected - no access inside
Hi, I have successfully configured remote access VPN router, it is connected, but no access to the inside, none of my ip addresses. I do not know SPLIT_ACL is ok and I've denied NATting them. For me, everything is ok. I did a lot in ASA, without anyproblem. Thanks for the comments.
enable secret 5 $1$ y0AJ$ rhrjbrpe5NDiAyHGlfeNi.
!
AAA new-model
!
!
AAA authentication login bcc_users local
AAA authorization bcc_group LAN
!
crypto ISAKMP policy 10
BA aes
preshared authentication
Group 2
!
ISAKMP crypto client configuration group ra_vpn_bcc
key *.
DNS 8.8.8.8
bcc.local field
pool vpn_pool
ACL SPLIT_ACL
Max-users 7
netmask 255.255.255.0
!
!
Crypto ipsec transform-set RIGHT aes - esp esp-sha-hmac
tunnel mode
!
!
!
Crypto-map dynamic dynmap 10
Set transform-set RIGHT
market arriere-route
!
!
card crypto client CRYPTO_VPN of authentication list bcc_users
card crypto isakmp authorization list bcc_group CRYPTO_VPN
crypto card for the CRYPTO_VPN client configuration address respond
map CRYPTO_VPN 10-isakmp ipsec crypto dynamic dynmap
!
!
interface GigabitEthernet0/0/4
IP address %.
NAT outside IP
auto negotiation
BFD interval 50 50 5 min_rx multiplier
card crypto CRYPTO_VPN
!
!
IP local pool vpn_pool 172.31.255.0 172.31.255.250
NAT extended IP access list
deny ip 10.0.0.0 0.255.255.255 172.31.255.0 0.0.0.255
deny ip 172.16.0.0 0.0.255.255 172.31.255.0 0.0.0.255
deny ip 192.168.0.0 0.0.255.255 172.31.255.0 0.0.0.255
IP address 172.16.0.0 allow 0.15.255.255 all
IP 192.168.0.0 allow 0.0.255.255 everything
IP 10.0.0.0 allow 0.255.255.255 everything
SPLIT_ACL extended IP access list
IP 10.0.0.0 allow 0.255.255.255 172.31.255.0 0.0.0.255
IP address 172.16.0.0 allow 0.0.255.255 172.31.255.0 0.0.0.255
IP 192.168.0.0 allow 0.0.255.255 172.31.255.0 0.0.0.255
Take a look at the delivery.
You do not have a route to the VPN pool on a nearby device.
Tags: Cisco Security
Similar Questions
-
Remote Desktop does not connect Win 7 on Win XP pro.
The two turned on, remote active and available on the same network. I tried to connect by the name and Ip address, but I still get the error message. Remote Desktop cannot connect to one of these reasons: 1 remote control, access to the server is not activated 2 remote computer is disabled 3 remote computer is not available on the network. I have connected before. In fact, I went to my computer in a click with the right button on the computer in the access network, it could not connect. He gave me the opportunity to diagnose the problem, so I chose it. The result of the diagnosis was the computer appears to be correctly configured but (computer) does not. I recently, during the last week, the object a new copy of windows xp pro on the computer and I have connected with access to distance since. Why can't connect now?
Check your firewall and router, the remote desktop protocol uses port 3389, this port must be opened.
John
-
Remote console does not connect: unexplained error
Running VMware server 2 on a Windows 2008 Enterprise.
Using a single remote adapter (with no Internet connection) with IP fixed 192.168.1.1 and no DNS/gateway server. The server is running a DHCP server (192.168.10 - 100).
WebAccess works when connecting to the local computer (the server) with IE 8.0, but the remote console does not work. It gives me this error:
Error opening of the remote virtual machine sidserver:8333\16:
Unexplained error. *
The same error occurs if connection to https://sidserver:8333, https://localhost:8333, https://127.0.0.1:8333, https://192.168.1.1:8333.
WebAccess does not work from another PC in the network: IE 8.0 just shows nothing. Firefox 3 offers a security certificate error dialogue do not allow me to add to the exceptions that the certificate is self-signed:
(translated :)
sidserver:8333 uses an invalid security certificate.
The certificate is not approved as being self-signed.
(Error code: sec_error_ca_cert_invalid)
Please reward points - we must know if we helped.
Click here to solve the problem-[http://communities.vmware.com/docs/DOC-9390: d-9390]
Click here for the manual http://www.vmware.com/pdf/vmserver2.pdf
-
Home network works great, remote desktop will not connect.
I have a Windows 7 laptop and a Vista laptop. They are connected to a secure wireless network. Both work very well as standalones. When I try to connect via Remote Desktop or connect with each other. My 7 is in a homegroup with a single name. My Vista is in a WORKING group with the same name. I can't connect either using remote desktop. Computer for both names are names of a single word, 'XXXXXX', not the format xxx.xxxxx.xxxx and I can't figure another way to their name. I spent 2 days serching various tech forums and tried what they suggested.
Hello
Homegroup is a unique feature of Win 7. It uses IPv6.
As you connect to Vista you must configure Windows 7 to the home network.
------------------------------------
Network Win 7 with another version of Windows as a work network (works very well if all computers are Win 7 also).
In the center of the network, by clicking on the type of network opens the window to the right.
Choose your network type. Note the check box at the bottom and check/uncheck depending on your needs.
For the best newspaper of the results of each computer screen system and together all computers on a network of the same name, while each computer has its own unique name.
http://www.ezlan.NET/Win7/net_name.jpg
------------------
Make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall on, Vista/XP Firewall Native should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructionsGeneral example, http://www.ezlan.net/faq.html#trusted
Please Note that some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic.If you end up with the 3rd party software uninstalled or disabled, make sure that Windows native firewall is active .
Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET
-
Remote Desktop is not connecting
I am trying to connect to a computer on my home network running W7 Professional using DRC. It is the only station that does not accept the connection. All are part of a domain. Is there a domain server. Symantic End Point Protection a firewall (firewall W7 is therefore off). My connection to the DRC is triggered by a W7 Ultimate station within the domain and specifies a port [STATION02:3390]. The router sends port 3390 to this post, and I get a good test of the router for this port. DRC is switched on to STATION02. I tried with and without network authentication. I tried to disable Ms. My domain name is called at the HOUSE and I entered my user name as an authorized user of the DRC on the host: HOME\richard and HOME\Domain users. All other computers on the network can RDC to each other, except STATION02 does not login as a host. I am stumpted and would appreciate help. Is there an area of setting I'm missing? Thank you.
Hello
Your Windows is better suited for the IT Pro TechNet public. Please post your question in the Remote Desktop Services forum.
You can follow the link to your question:
http://social.technet.Microsoft.com/forums/en/winserverTS/threads
-
HP Officejet 6700 Premium: IHP AIO Remote app does not connect to my printer.
Tried to use HP AIO remote with my printer HP officejets 6700 Premium. I get a message that is offline. However, it is not. I tried to turn my printer market and restarted my computer. It did not work. I noticed that the
the IP address for my printer HP officejets 6700 Premium on the app is not the same as the address of my printer. If this is the problem how can I fix it? In any case, please help. I use a Dell with Windpws 10 laptop
Wally
Hello @wwwally, greetings!
Thank you for visiting the Forums from the HP Support! It's a good place to find the help you need, other users, HP experts and other support staff.
Going through your post, application remote control HP AIO is mainly used in mobile devices and not in laptops.
I suggest you download and use HP Scan and capture app to scan from your laptop Win 10. You can go to http://hp.care/2bUVkrw to download and install HP Scan and capture the app.
Please let me know if that solves the problem, or if you need assistance.
See you soon
Please click on 'acceptable' on the post that solves your problem to help others to find the solution. To show gratitude for my help, please click the 'Thumbs Up icon' below!
-
Hello
I don't know what could be held, vpn users can ping to the outside and inside of the Cisco ASA interface but can not connect to servers or servers within the LAN ping.
is hell config please kindly and I would like to know what might happen.
hostname horse
domain evergreen.com
activate 2KFQnbNIdI.2KYOU encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
ins-guard
!
interface GigabitEthernet0/0
LAN description
nameif inside
security-level 100
192.168.200.1 IP address 255.255.255.0
!
interface GigabitEthernet0/1
Description CONNECTION_TO_FREEMAN
nameif outside
security-level 0
IP 196.1.1.1 255.255.255.248
!
interface GigabitEthernet0/2
Description CONNECTION_TO_TIGHTMAN
nameif backup
security-level 0
IP 197.1.1.1 255.255.255.248
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
management only
!
boot system Disk0: / asa844-1 - k8.bin
boot system Disk0: / asa707 - k8.bin
passive FTP mode
clock timezone WAT 1
DNS server-group DefaultDNS
domain green.com
network of the NETWORK_OBJ_192.168.2.0_25 object
Subnet 192.168.2.0 255.255.255.128
network of the NETWORK_OBJ_192.168.202.0_24 object
192.168.202.0 subnet 255.255.255.0
network obj_any object
subnet 0.0.0.0 0.0.0.0
the DM_INLINE_NETWORK_1 object-group network
object-network 192.168.200.0 255.255.255.0
object-network 192.168.202.0 255.255.255.0
the DM_INLINE_NETWORK_2 object-group network
object-network 192.168.200.0 255.255.255.0
object-network 192.168.202.0 255.255.255.0
access-list extended INSIDE_OUT allow ip 192.168.202.0 255.255.255.0 any
access-list extended INSIDE_OUT allow ip 192.168.200.0 255.255.255.0 any
Access extensive list permits all ip a OUTSIDE_IN
gbnlvpntunnel_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0
standard access list gbnlvpntunnel_splitTunnelAcl allow 192.168.202.0 255.255.255.0
gbnlvpntunnell_splitTunnelAcl standard access list allow 192.168.200.0 255.255.255.0
standard access list gbnlvpntunnell_splitTunnelAcl allow 192.168.202.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
backup of MTU 1500
mask of local pool VPNPOOL 192.168.2.0 - 192.168.2.100 IP 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm-645 - 206.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination
NAT (inside, backup) static source NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.202.0_24 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination
NAT (inside, outside) static source DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination
NAT (inside, backup) static source DM_INLINE_NETWORK_2 DM_INLINE_NETWORK_2 NETWORK_OBJ_192.168.2.0_25 NETWORK_OBJ_192.168.2.0_25 non-proxy-arp-search of route static destination
!
network obj_any object
dynamic NAT interface (inside, backup)
Access-group interface inside INSIDE_OUT
Access-group OUTSIDE_IN in interface outside
Route outside 0.0.0.0 0.0.0.0 196.1.1.2 1 track 10
Route outside 0.0.0.0 0.0.0.0 197.1.1.2 254
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
Enable http server
http 192.168.200.0 255.255.255.0 inside
http 192.168.202.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
monitor SLA 100
type echo protocol ipIcmpEcho 212.58.244.71 interface outside
Timeout 3000
frequency 5
monitor als 100 calendar life never start-time now
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
backup_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
backup of crypto backup_map interface card
Crypto ikev1 allow outside
Crypto ikev1 enable backup
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
!
track 10 rtr 100 accessibility
Telnet 192.168.200.0 255.255.255.0 inside
Telnet 192.168.202.0 255.255.255.0 inside
Telnet timeout 5
SSH 192.168.202.0 255.255.255.0 inside
SSH 192.168.200.0 255.255.255.0 inside
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 15
SSH group dh-Group1-sha1 key exchange
Console timeout 0
management-access inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal group vpntunnel strategy
Group vpntunnel policy attributes
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpntunnel_splitTunnelAcl
field default value green.com
internal vpntunnell group policy
attributes of the strategy of group vpntunnell
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list gbnlvpntunnell_splitTunnelAcl
field default value green.com
Green user name encrypted BoEFKkDtbnX5Uy1Q privilege 15 password
attributes of user name THE
VPN-group-policy gbnlvpn
tunnel-group vpntunnel type remote access
tunnel-group vpntunnel General attributes
address VPNPOOL pool
strategy-group-by default vpntunnel
tunnel-group vpntunnel ipsec-attributes
IKEv1 pre-shared-key *.
type tunnel-group vpntunnell remote access
tunnel-group vpntunnell General-attributes
address VPNPOOL2 pool
Group Policy - by default-vpntunnell
vpntunnell group of tunnel ipsec-attributes
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns migrated_dns_map_1
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:7c1b1373bf2e2c56289b51b8dccaa565
Hello
1 - Please run these commands:
"crypto isakmp nat-traversal 30.
"crypto than dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 Road opposite value.
The main issue here is that you have two roads floating and outside it has a better than backup metric, that's why I added the command 'reverse-road '.
Please let me know.
Thank you.
-
Cisco ASA 8.4 (3) remote access VPN - client connects but cannot access inside the network
I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well
Thank you
interface Ethernet0/0
Speed 100
full duplex
nameif outside
security-level 0
IP x.x.x.x 255.255.255.240
!
interface Ethernet0/1
Speed 100
full duplex
nameif inside
security-level 100
IP 10.88.10.254 255.255.255.0
!
interface Management0/0
Shutdown
nameif management
security-level 0
no ip address
!
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network of the PAT_to_Outside_ClassA object
10.88.0.0 subnet 255.255.0.0
network of the PAT_to_Outside_ClassB object
subnet 172.16.0.0 255.240.0.0
network of the PAT_to_Outside_ClassC object
Subnet 192.168.0.0 255.255.240.0
network of the LocalNetwork object
10.88.0.0 subnet 255.255.0.0
network of the RemoteNetwork1 object
Subnet 192.168.0.0 255.255.0.0
network of the RemoteNetwork2 object
172.16.10.0 subnet 255.255.255.0
network of the RemoteNetwork3 object
10.86.0.0 subnet 255.255.0.0
network of the RemoteNetwork4 object
10.250.1.0 subnet 255.255.255.0
network of the NatExempt object
10.88.10.0 subnet 255.255.255.0
the Site_to_SiteVPN1 object-group network
object-network 192.168.4.0 255.255.254.0
object-network 172.16.10.0 255.255.255.0
object-network 10.0.0.0 255.0.0.0
outside_access_in deny ip extended access list a whole
inside_access_in of access allowed any ip an extended list
11 extended access-list allow ip 10.250.1.0 255.255.255.0 any
outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1
mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool
NAT static NatExempt NatExempt of the source (indoor, outdoor)
NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3
NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search
!
network of the PAT_to_Outside_ClassA object
NAT dynamic interface (indoor, outdoor)
network of the PAT_to_Outside_ClassB object
NAT dynamic interface (indoor, outdoor)
network of the PAT_to_Outside_ClassC object
NAT dynamic interface (indoor, outdoor)
Access-group outside_access_in in interface outside
inside_access_in access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
dynamic-access-policy-registration DfltAccessPolicy
Sysopt connection timewait
Service resetoutside
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto-map dynamic dynmap 10 set pfs
Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1
life together - the association of security crypto dynamic-map dynmap 10 28800 seconds
Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000
Crypto-map dynamic dynmap 10 the value reverse-road
card crypto mymap 1 match address outside_1_cryptomap
card crypto mymap 1 set counterpart x.x.x.x
card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1
card crypto mymap 86400 seconds, 1 lifetime of security association set
map mymap 1 set security-association life crypto kilobytes 4608000
map mymap 100-isakmp ipsec crypto dynamic dynmap
mymap outside crypto map interface
crypto isakmp identity address
Crypto isakmp nat-traversal 30
Crypto ikev1 allow outside
IKEv1 crypto ipsec-over-tcp port 10000
IKEv1 crypto policy 5
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 1
life 86400
IKEv1 crypto policy 50
preshared authentication
the Encryption
md5 hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
preshared authentication
aes-256 encryption
sha hash
Group 1
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Telnet timeout 5
Console timeout 0
management-access inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal BACKDOORVPN group policy
BACKDOORVPN group policy attributes
value of VPN-filter 11
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelall
BH.UK value by default-field
type tunnel-group BACKDOORVPN remote access
attributes global-tunnel-group BACKDOORVPN
address pool Admin_Pool
Group Policy - by default-BACKDOORVPN
IPSec-attributes tunnel-group BACKDOORVPN
IKEv1 pre-shared-key *.
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
Excellent.
Evaluate the useful ticket.
Thank you
Rizwan James
-
Cisco vpn 5.0.07.0440 - k9 connected but not the network remote access to Windows 8.1 pro
I use 5.0.07.0440 - k9 vpn Cisco and Cisco vpn 5.0.07.0290 - k9 both version on our 8.1 Windows Mobile pro.
VPN connected successfully, but not remote access network and receive no ping.But when I try with wifi and vpn, then good job.
Please help me as soon as possible.
Thank you
SanjibIt is very problematic on Windows 8 and EOL now.
Kind regards
Nehmaan
-
Client remote access VPN gets connected without access to the local network
: Saved
:
ASA 1.0000 Version 2
!
hostname COL-ASA-01
domain dr.test.net
turn on i/RAo1iZPOnp/BK7 encrypted password
i/RAo1iZPOnp/BK7 encrypted passwd
names of
!
interface GigabitEthernet0/0
nameif outside
security-level 0
IP 172.32.0.11 255.255.255.0
!
interface GigabitEthernet0/1
nameif inside
security-level 100
IP 192.9.200.126 255.255.255.0
!
interface GigabitEthernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5
nameif failover
security-level 0
192.168.168.1 IP address 255.255.255.0 watch 192.168.168.2
!
interface Management0/0
nameif management
security-level 0
192.168.2.11 IP address 255.255.255.0
!
passive FTP mode
DNS server-group DefaultDNS
domain dr.test.net
network of the RAVPN object
192.168.0.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.200.0_24 object
192.168.200.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.9.200.0_24 object
192.9.200.0 subnet 255.255.255.0
the inside_network object-group network
object-network 192.9.200.0 255.255.255.0
external network object-group
host of the object-Network 172.32.0.25
Standard access list RAVPN_splitTunnelAcl allow 192.9.200.0 255.255.255.0
access-list extended test123 permit ip host 192.168.200.1 192.9.200.190
access-list extended test123 permit ip host 192.9.200.190 192.168.200.1
access-list extended test123 allowed ip object NETWORK_OBJ_192.168.200.0_24 192.9.200.0 255.255.255.0
192.9.200.0 IP Access-list extended test123 255.255.255.0 allow object NETWORK_OBJ_192.9.200.0_24
pager lines 24
management of MTU 1500
Outside 1500 MTU
Within 1500 MTU
failover of MTU 1500
local pool RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 IP mask
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 66114.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) source Dynamics one interface
NAT (it is, inside) static static source NETWORK_OBJ_192.9.200.0_24 destination NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.9.200.0_24
Route outside 0.0.0.0 0.0.0.0 172.32.0.2 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 0.0.0.0 0.0.0.0 outdoors
http 0.0.0.0 0.0.0.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
Crypto ca trustpoint ASDM_TrustPoint0
Terminal registration
name of the object CN = KWI-COL-ASA - 01.dr.test .net, C = US, O = KWI
Configure CRL
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet 192.9.200.0 255.255.255.0 inside
Telnet timeout 30
SSH 0.0.0.0 0.0.0.0 management
SSH 0.0.0.0 0.0.0.0 outdoors
SSH 66.35.45.128 255.255.255.192 outside
SSH 0.0.0.0 0.0.0.0 inside
SSH timeout 30
SSH version 2
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
internal RAVPN group policy
RAVPN group policy attributes
value of server WINS 192.9.200.164
value of 66.35.46.84 DNS server 66.35.47.12
VPN-filter value test123
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value test123
Dr.kligerweiss.NET value by default-field
username test encrypted password xxxxxxx
username admin password encrypted aaaaaaaaaaaa privilege 15
vpntest Delahaye of encrypted password username
type tunnel-group RAVPN remote access
attributes global-tunnel-group RAVPN
address RAVPN pool
Group Policy - by default-RAVPN
IPSec-attributes tunnel-group RAVPN
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory 2
Subscribe to alert-group configuration periodic monthly 2
daily periodic subscribe to alert-group telemetry
aes encryption password
Cryptochecksum:b001e526a239af2c73fa56f3ca7667ea
: end
COL-ASA-01 #.
Here is a shot made inside interface which can help as well, I've tried pointing the front door inside the interface on the target device, but I think it was a switch without ip route available on this subject I think which is always send package back to Cisco within the interface
Test of Cape COLLAR-ASA-01 # sho | in 192.168.200
25: 23:45:55.570618 192.168.200.1 > 192.9.200.190: icmp: echo request
29: 23:45:56.582794 192.168.200.1.137 > 192.9.200.164.137: udp 68
38: 23:45:58.081050 192.168.200.1.137 > 192.9.200.164.137: udp 68
56: 23:45:59.583176 192.168.200.1.137 > 192.9.200.164.137: udp 68
69: 23:46:00.573517 192.168.200.1 > 192.9.200.190: icmp: echo request
98: 23:46:05.578110 192.168.200.1 > 192.9.200.190: icmp: echo request
99: 23:46:05.590057 192.168.200.1.137 > 192.9.200.164.137: udp 68
108: 23:46:07.092310 192.168.200.1.137 > 192.9.200.164.137: udp 68
115: 23:46:08.592468 192.168.200.1.137 > 192.9.200.164.137: udp 68
116: 23:46:10.580795 192.168.200.1 > 192.9.200.190: icmp: echo request
COL-ASA-01 #.
Any help or pointers greatly appreciated, I have do this config after a long interval on Cisco of the last time I was working it was all PIX so just need to expert eyes to let me know if I'm missing something.
And yes I don't have a domestic network host to test against, all I have is a switch that cannot route and bridge default ip helps too...
Hello
The first thing you should do to avoid problems is to change the pool VPN to something else than the current LAN they are not really directly connected in the same network segment.
You can try the following changes
attributes global-tunnel-group RAVPN
No address RAVPN pool
no mask RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 ip local pool
local pool RAVPN 192.168.201.1 - 192.168.201.254 255.255.255.0 IP mask
attributes global-tunnel-group RAVPN
address RAVPN pool
no nat (it is, inside) static source NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 static destination NETWORK_OBJ_192.9.200.0_24 NETWORK_OBJ_192.9.200.0_24
In the above you first delete the VPN "tunnel-group" Pool and then delete and re-create the VPN pool with another network and then insert the same "tunnel-group". NEX will remove the current configuration of the NAT.
the object of the LAN network
192.168.200.0 subnet 255.255.255.0
network of the VPN-POOL object
192.168.201.0 subnet 255.255.255.0
NAT (inside, outside) 1 static source LAN LAN to static destination VPN-VPN-POOL
NAT configurations above adds the correct NAT0 configuration for the VPN Pool has changed. It also inserts the NAT rule to the Summit before the dynamic PAT rule you currently have. He is also one of the problems with the configurations that it replaces your current NAT configurations.
You have your dynamic PAT rule at the top of your NAT rules currently that is not a good idea. If you want to change to something else will not replace other NAT configurations in the future, you can make the following change.
No source (indoor, outdoor) nat Dynamics one interface
NAT source auto after (indoor, outdoor) dynamic one interface
NOTICE! PAT dynamic configuration change above temporarily interrupt all connections for users on the local network as you reconfigure the dynamic State PAT. So if you make this change, make sure you that its ok to still cause little reduced in the current internal users connections
Hope this helps
Let me know if it works for you
-Jouni
-
Through remote access vpn Ipsec within the host is not available.
Team,
I have a question in confiuration vpn crossed.
ASA 3,0000 Version 5
the only question is, to access remote vpn clinet IP cannot access inside the host. However able to reach the branch of IP and it uses corprate Internet.
In SAA from the external interface I am able to ping remote clint IP but not from within the interface. Please help and let me know if additional information is required.
Thank you
Knockaert
Hello
For the NAT0 configuration, you only need NAT0 instruction for the interface "inside".
This single command/ACL should allow for 'inside' <-->'vpn-pool' communication.
NAT0 configurations on the 'external' interface should be necessary only if you make NAT0 between 2 VPN connections. I guess you could do this since you mention traffic crossed?
I suggest using different 'object-group' to define networks of NAT0 destination for different ' object-group' to the 'outside' to 'outside' and 'inside' users NAT0.
I also obsessively using beaches too wide network in the statements of NAT0. According to some records, they can cause problems
For example, this network ' object-network 172.16.0.0 255.240.0.0 "contains the 172.x.x.x.x set private IP address range. And in this case it contains some of your 'inside' networks too?
How is this a problem of crossed by the way? You say that the problem is between the VPN clients on the 'external' interface and network local hosts behind the 'internal '? Crossed would mean you have connection problem between 'outside' <->'outside' perhaps.
I don't know if I made any sense. Can be a bit messy. But can not give very specific answers that I don't know the entire configuration.
Also make sure you have the "inspect icmp" configured under the policy-map of the world, so that the response to ICMP echo messages are automatically allowed through the ASA.
-Jouni
-
VPN remote access - no network connectivity internal!
Hi Experts,
I understand that it is a very common problem when considering the implementations of IPSec VPN for remote access using Cisco VPN Client. But for the last six months, I have tried to configure remote VPN access to as many sites customer and gets stuck to the top with the same question!
-The remote VPN Client connects, authenticates successfully to the local user database (to make things easier, I used the local user authentication), the tunnel is set up (I could see the exit of the isakmp #show her as a AM_ACTIVE ). So I think that the parameters of encryption and authentication for Phase 1 /Phase 2 should work because the tunnel is having successfully established
-Now comes the question, no connectivity to the internal network. I tried all the possible solutions, that I could find online.
1. the most common problem is NAT - Traversal not active
-Compatible NAT - T with the time default keepalive of 20
2. None of the configurations NAT to exempt remote VPN traffic
-A ensured that Nat configurations not present in configuration and internal network 192.168.1.X VPN traffic networks VPN 192.168.5.X /192.168.10.X being exempted NAT
3-Split tunnel configurations
-Reconfigured Split tunnel access list configuration Standard access list expanded (although not required as a Standard access list is more than enouugh, if I'm not mistaken) to allow traffic selected from 192.168.1.X for 192.168.5.X/192.168.10.X that will create routes on Client that allows users to simultaneously access VPN resources and access Internet VPN client. The Tunnel from Split network group was added again to the group policy.
4 enabled Perfect Forward Secrecy (PFS) /Disabled
. It may be an extra charge, it has been disabled / enabled
5. the road opposite Injection
-Ensured that a temporary reverse route has been injected to the routing table by allowing the reverse Route Injection to insert automatically the temporary static routes to the remote tunnel using the command set reverse road networks
A few more interesting things were noted:
Encrypted and Bypassed packages found when a continuous ping started the ASA inside the interface.
No decryption happens of the VPN Client, which means that there is no answer back from the network traffic statistics.
Decryption and packages are found be increasing when I try to ping of the IP address to the customer (192.168.0.10) has published the SAA. But on the SAA, I'm not back any response and showing as? . So that would mean that there is communication of ASA to the customer via the VPN tunnel while no communication is happening from the internal network to the customer
The entire configuration is shown below
ASA Version 8.2 (1)
!
ciscoasa hostname
activate the encrypted password of AS3P3A8i0l6.JxwD
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
address IP X.X.X.X 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
access-list extended SHEEP allowed ip 192.168.1.0 255.255.255.0 192.168.0.0 255.255.255.0
ST1 list extended access permitted ip 192.168.1.0 255.255.255.0 192.168.0.0 255.255.255.0
pager lines 24
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
IP local pool testpool 192.168.0.10 - 192.168.0.15
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0 access-list SHEEP
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 X.X.X.X 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
AAA authentication enable LOCAL console
AAA authentication http LOCAL console
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
Enable http server
http 192.168.1.0 255.255.255.0 inside
http 0.0.0.0 0.0.0.0 inside
http 0.0.0.0 0.0.0.0 outdoors
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac FirstSet
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dyn1 1jeu transform-set FirstSet
Crypto-map dynamic dyn1 1jeu reverse-road
dynamic mymap 1 dyn1 ipsec-isakmp crypto map
mymap outside crypto map interface
crypto ca server
SMTP address [email protected] / * /
crypto ISAKMP allow outside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH 0.0.0.0 0.0.0.0 inside
SSH timeout 5
Console timeout 0
dhcpd outside auto_config
!
dhcpd address 192.168.1.10 - 192.168.1.132 inside
dhcpd dns 8.8.8.8 4.4.4.4 interface inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal RAVPN group policy
RAVPN group policy attributes
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value ST1
the address value testpool pools
dk Z6zukyDvwVjP7o24 encrypted privilege 15 password username
sv i1gRUVsEALixX3ei encrypted password username
tunnel-group testgroup type remote access
tunnel-group testgroup General attributes
address testpool pool
Group Policy - by default-RAVPN
testgroup group tunnel ipsec-attributes
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:48f0863a70b8f382c7b71db0b88620fe
: end----
Could you please help me identify where I'm going wrong. Its been a long time I have trying to figure out but nothing seems to work! ;-(
Help, please!
Thank you
ANUP
(1) pls replace the tunnel ACL ACL standard split as follows:
no extended ST1 192.168.1.0 ip access list allow 255.255.255.0 192.168.0.0 255.255.255.0
access-list allowed ST1 192.168.1.0 255.255.255.0
(2) add icmp inspection:
Policy-map global_policy
class inspection_default
inspect the icmp
(3) Finally, I add the following so that you can test the ASA inside the interface:
management-access inside
-
Remote Access Auto Connection Manager and error with a VPN work
I use my laptop to connect to my VPN working. It has not worked since June 24, 2010. I get a message indicating that the connection to network access device is not found. I also have a problem with the connection manager automatic remote access. I'm trying to launch and get an error code 5, unauthorized. The Auto Connection Manager remote access has something to do with the vpn access problem and if so how can I solve this problem?
Hello hitherandthee,
Your question of Windows Vista is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the platform of networking on TechNet. Following your question thanks for posting the link below:
http://social.technet.Microsoft.com/forums/en-us/winserverPN/threads?page=10
Thank you
Irfan H, Engineer Support Microsoft Answers. Visit our Microsoft answers feedback Forum and let us know what you think. -
VPN error 868 the name of the remote access server is not resolved
I use Windows 7 Home Premium and you want to configure a VPN with my office network that uses the Check Point Safe@Office. I am unable to log in and get the error that does not resolve the name of the remote access server and Windows cannot find the host using DNS name. Any suggestions on what to try to fix the problem? I set up the VPN connection according to the instructions of our network administrator. We use XP in the office.
Hello
Welcome to the Microsoft answers siteThe question that you'd be better suited in the TechNet community. Please visit the link below to find a community that will provide the best support.
http://social.technet.Microsoft.com/forums/en-us/ForefrontedgeVPN/threadsIt may be useful
Thanks and greetings
Support Microsoft-dieng
Visit our Microsoft answers feedback Forum and let us know what you think
http://social.answers.Microsoft.com/forums/en-us/answersfeedback/threads/ -
Access PIX using SSH when connected remotely with VPN client
Hello
I think that this should be a fairly simple for someone to sort for me - I'm new to PIX configuration If Yes please excuse my stupidity!
I changed the config on our PIX to allow only access via SSH (rather than via telnet as it was previously configured)
Now, everything works fine when I'm in the office - I can connect to the PIX using SSH without any problem.
However, if I work from home and connect to the office using my VPN client (IPSEC tunnel ends on the PIX firewall itself) I find that I can not connect to the PIX.
I have configured the PIX to access ssh on the office LAN subnet and the client pool of IP addresses used for VPN connections by using the following commands:
SSH 172.64.10.0 255.255.255.0 inside
SSH 192.28.161.0 255.255.255.0 inside
where the 1st line is reference to the office's LAN, which works very well, and the 2nd line denotes the IP address pool configured on the PIX for VPN access.
Can someone tell me how to fix this? I have the feeling that its something pressing!
Thank you
Neil
Try the command "management-access to the Interior.
Maybe you are looking for
-
490 error code when you try to install service pack 2 with vista
I have service pack 1 installed on my computer but I get an error message when you try to install service pack 2
-
This windows bug has been reported and 'responded' before by several people, but the "answers" do not work for me - and they do seem to work for a lot of people in this area and other forums. I hope you can provide me with a real estate diagnosis, a
-
upgrading to win 10, but get this errorC1900101""WindowsUpdate_dt000"
Moving it to 10 but get this errorC1900101""Windows Update_dt000 ".
-
Hello worldWe have our source CSV (Delimter file) file requirement we have subfoldersAccount currency amount CostcenterC001 1001 USD 10001002 C002 2000 INR1003 C003 3000 EURAccording the data above, we want to only data records USD will be imported i
-
How to recognize an uninstall to allow installation on a new computer by Adobe?
How to recognize an uninstall to allow installation on a new computer by Adobe?