Remote vpn client can't access outside networks
I configured a remote vpn ASA 5510 the wizard remote vpn. Users are able to get the vpn connection and access the internal network; but IMPOSSIBLE to
access the outside network. (For the internal network, I want to talk about network behind the vpn to ASA, outside networks refers to society outside the ASA).
In short, the external network of the company has default route to the ROUTER1 points. The ROUTER1 has road for access network and a default route to the internet. The ASA has a default route to the ROUTER1 points. the ROUTER1 also has a route to the address of the user remote vpn refers to the ASA.
Hope it wise.
But I don't know if my nat statement is correct. below is my statement of nat, is there something obvious lack? There is no translation network here, routable internet addresses.
NAT (inside) 0-list of access inside_nat0_outbound
public static 111.1.0.0 (Interior, exterior) 111.1.0.0 netmask 255.255.255.0
public static 111.1.1.0 (Interior, exterior) 111.1.1.0 netmask 255.255.255.0
public static 111.1.2.0 (Interior, exterior) 111.1.2.0 netmask 255.255.255.0
networks outside the company (111.1.3.0/24; 111.1.4.0/24)
|
|
the user remote vpn <-------------->internet <--------------------->ROUTER1 - ASA - Cat6509 - inside the network
Any suggestion is appreciated.
Thank you
have you enabled "same-security-traffic intra-interface.
--------------------->-------------->
Tags: Cisco Security
Similar Questions
-
AnyConnect client can not access local network
Hello
I have a problem with the Cisco anyconnect. Once clients are connected they cannot access anything whatsoever, including their default gateway.
Pool of the VPN client is on the same subnet as the LAN (139.16.1.x/24). Local network clients can access DMZ, VPN clients can ping computers on the local network, but they cannot access the DMZ.
I guess that any rule providing that traffic is absent but I m new with Cisco ASA and I m totally lost. I read as much as I could on this topic, but I do not understand which rule is necessary.
Thank you very much in advance for your support.
ASA release 9.4 (1)
!
ciscoasa hostname
activate the encrypted password of WmlxhdtfAnw9XbcA
TA.qizy4R//ChqQH encrypted passwd
names of
mask 139.16.1.50 - 139.16.1.80 255.255.255.0 IP local pool Pool_139
!
interface GigabitEthernet1/1
nameif outside
security-level 0
192.168.1.100 IP address 255.255.255.0
!
interface GigabitEthernet1/2
nameif inside
security-level 100
IP 139.16.1.1 255.255.255.0
!
interface GigabitEthernet1/3
nameif DMZ
security-level 50
IP 172.16.1.1 255.255.255.0
!
interface GigabitEthernet1/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet1/5
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet1/6
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet1/7
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet1/8
Shutdown
No nameif
no level of security
no ip address
!
Management1/1 interface
management only
nameif management
security-level 100
11.11.11.11 IP address 255.255.255.0
!
passive FTP mode
network obj_any object
subnet 0.0.0.0 0.0.0.0
internal subnet object-
139.16.1.0 subnet 255.255.255.0
network dmz subnet object
subnet 172.16.1.0 255.255.255.0
wialon Server external ip network object
Home 192.168.1.132
wialon-Server network objects
Home 172.16.1.69
Wialon-service-TCP object service
destination tcp source between 1 65535 21999 20100 service range
Wialon-service-UDP object service
destination service udp source between 0 65535 21999 20100 range
network of the NETWORK_OBJ_139.16.1.0_25 object
subnet 139.16.1.0 255.255.255.128
outside_acl list extended access permit tcp any object wialon-Server eq www
outside_acl list extended access allowed object Wialon-service-TCP any wialon-server object
outside_acl list extended access allowed object Wialon-service-UDP any wialon-server object
pager lines 24
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
MTU 1500 DMZ
management of MTU 1500
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) static source any any static destination NETWORK_OBJ_139.16.1.0_25 NETWORK_OBJ_139.16.1.0_25 non-proxy-arp-search to itinerary
!
network obj_any object
dynamic NAT (all, outside) interface
internal subnet object-
NAT dynamic interface (indoor, outdoor)
wialon-Server network objects
NAT (DMZ, external) service wialon Server external ip static tcp www www
Access-group outside_acl in interface outside
Route outside 0.0.0.0 0.0.0.0 192.168.1.1 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
identity of the user by default-domain LOCAL
Enable http server
http 11.11.11.0 255.255.255.0 management
http 139.16.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
service sw-reset button
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
Crypto ca trustpoint ASDM_TrustPoint0
registration auto
domain name full ciscoasa.srdongato.null
E-mail [email protected] / * /
name of the object CN = srdongato
Serial number
Proxy-loc-transmitter
Configure CRL
Crypto ca trustpoint ASDM_Launcher_Access_TrustPoint_0
registration auto
full domain name no
name of the object CN = 139.16.1.1, CN = ciscoasa
ASDM_LAUNCHER key pair
Configure CRL
trustpool crypto ca policy
string encryption ca ASDM_TrustPoint0 certificates
certificate 09836256
30820381 30820269 a0030201 02020409 83625630 0d06092a 864886f7 0d 010105
05003050 31123010 06035504 03130973 72646f6e 6761746f 313 has 3012 06035504
05130b4a a 41443139 32323033 34343024 06092, 86 01090216 17636973 4886f70d
636f6173 612e7372 646f6e67 61746f2e 6e756c6c 31353132 30353036 301e170d
5a170d32 33333535 35313230 32303633 3335355a 30503112 30100603 55040313
09737264 6f6e6761 30120603 55040513 31393232 30333434 0b4a4144 746f313a
2a 864886 30240609 f70d0109 6973636f 02161763 6173612e 7372646f 6e676174
6f2e6e75 6c6c3082 0122300d 06092 has 86 01010105 00038201 0f003082 4886f70d
010a 0282 010100d 2 295e679c 153e8b6a d3f6131d 8ea646e3 aa0a5fa9 20e49259
ca895563 7e818047 033a4e8f 57f619e9 fa93bfd5 6c44141f b0abf2c0 8b86334e
bac63f41 99e6d676 c689dcf7 080f2715 038a8e1b 694a00de 7124565e a1948f09
8dbeffab c7c8a028 741c5b10 d0ede5e9 599f38fe 5b88f678 4decdc4b b 353, 6708
cfa2fbce f58be06e 18feba56 4b2b04a1 77773ec6 5c58d2ed d7ca4f17 980f0353
138bfe65 1b1165e6 7b6f94bb ab4d4286 e900178c 147a6dba 2427f38e e225030f
0a66d1eb 5075c57e 6d77e5bb 247f5bc3 8d3530f0 49dedf2d 21a24b5f daa08d98
690183cf e82a6b8d 5e489956 c5eecdbc 7fc2365c b629a52b 126b51e2 18590ed5
c9da8503 a639f102 03010001 a3633061 300f0603 551d 1301 01ff0405 30030101
ff300e06 03551d0f 0101ff04 86301f06 04030201 23 04183016 80143468 03551d
dec79103 0a91b530 1ada7e47 7e27b16d 4186301d 0603551d 0e041604 143468de
c791030a 91b5301a da7e477e 27b16d41 86300d 86f70d01 01050500 06 092 a 8648
003cdb04 03820101 8ef5ed31 c05c684b ad2b0062 96bfd39a ecb0a3fe 547aebe5
14b753e7 89f55827 3d4e0aa8 b8674e45 80d4c023 8e99a7b4 0907d 347 060a2fe4
fa6e0c2f 3b9cd708 a539c09f 7022d2ee fb6e2cf6 82b0e861 a2839a71 1512b3ec
e28664e9 732270c 9 d1c679d9 1eaf2ad5 31c3ff97 09aae869 88677a3d b 007, 5699
ecb3032e 2dd0f74f 81f9a8fb 79f30809 723bbdbf dfef4154 5ad6b012 a8f37093
481fa678 b44b0290 23390036 042828f3 5eefdc43 ebe52d26 78934455 9b4234a9
4146 166e5adc b431f12f 8d0fbf16 46306228 731c bfeebc43 34 76984 d2e6ebbc
88ca120a 96838694 d4f32884 963e7385 987ec6b0 dfa28d49 05ba5fa8 641bcfc7
ff92ac3c 52
quit smoking
string encryption ca ASDM_Launcher_Access_TrustPoint_0 certificates
Certificate 0 is 836256
308202cc a0030201 0202040a 0d06092a 83625630 864886f7 0d 010105 308201b 4
05003028 06035504 03130863 61736131 13301106 03550403 6973636f 3111300f
130a 3133 392e3136 2e312e31 31353132 30353036 35363236 5a170d32 301e170d
35313230 32303635 3632365a 30283111 55040313 08636973 636f6173 300f0603
61311330 11060355 0403130 3133392e 31362e31 2e313082 0122300d 06092 has 86
4886f70d 01010105 00038201 0f003082 010 has 0282 010100e7 a5c16e86 16c15a10
e018b868 bac7271a 30f1a3f8 ecb9c6b8 3ed4b1ad c9468f5e 287f2a7a 644f1496
c43a061e da927d09 a755b53e ed7c6a66 f2f1fb1e f944345c 86e08ce0 891c99b3
13101ab3 04963fad f91f987f 99f22a89 cd1e8c5a 5e4c026d 2cadd7b7 6620bbd1
b4a5135b 24ec886f fa061a06 dd536e96 1e483730 756c 4101 23f83a8d 944a7fbe
93c51d56 32ac0d17 ceb75f63 0ae24f07 f2c54e83 5b84ff00 16b0b899 c925c737
1765b 066 23 b 54645 bc419684 d09dd130 c1479949 68b0a779 df39b078 6fb0deb9
758b14c3 f0801faf f0ad60e1 a018ffba d769f867 3fe8e5fc 88ccc5b2 2319f5d4
617a78c4 74e7a64b 5c68276c 06ea57c1 d0ffce4b 358c4d02 03010001 300 d 0609
2a 864886 05050003 82010100 dff97c9f 4256fd47 8eb661fd d22ecea4 f70d0101
589eff09 958e01f1 a435a20e 5ed1cf19 af42e54d d61fc0ab cb2ee7ac 7fcb4513
1a44cc86 1e020d72 3a3f78d2 4 d 225177 857093d 9 f5fcf3c7 6e656d2b 54a0c522
f636b8cf 33c5ae34 ea340f32 85dff4c1 50165e7a e94de10b ced15752 0b3a76c1
2a50777b 20291106 a1a8a214 a 8 003716 680c15d4 ac3f7cc7 378f8f5f 38e3403f
f958c095 e549c8ed 4baf8cc5 bdcd230e 260754ea 953c3a4c eb01fef5 62b97e01
9f82ce6b f479dbdd 000c45af 8758b35f b4a958ee 32c4db3f 2ddc7385 dc05b0e3
78b609ba a9280841 2433ae87 5dd7a7c2 d5691068 1dc0eddc c23f99c5 3df8b1a5
aadbd82a 423f4ba8 563142bf 742771c 3
quit smoking
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 activate out of service the customer port 443
Crypto ikev2 access remote trustpoint ASDM_TrustPoint0
Telnet 139.16.1.0 255.255.255.0 inside
Telnet 11.11.11.0 255.255.255.0 management
Telnet timeout 5
without ssh stricthostkeycheck
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0
dhcpd outside auto_config
!
dhcpd address 172.16.1.69 - DMZ 172.16.1.69
dhcpd dns 87.216.1.65 87.216.1.66 DMZ interface
dhcpd option 3 ip 172.16.1.1 DMZ interface
dhcpd enable DMZ
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
SSL-trust outside ASDM_TrustPoint0 point
SSL-trust ASDM_Launcher_Access_TrustPoint_0 inside point
Trust ASDM_Launcher_Access_TrustPoint_0 inside the vpnlb-ip SSL-point
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-win-3.1.12020-k9.pkg 1
AnyConnect profiles Wialon_client_profile disk0: / Wialon_client_profile.xml
AnyConnect enable
tunnel-group-list activate
Disable error recovery
internal GroupPolicy_Wialon group strategy
attributes of Group Policy GroupPolicy_Wialon
WINS server no
value of 192.168.1.1 DNS server
client ssl-VPN-tunnel-Protocol ikev2
by default no
WebVPN
AnyConnect value Wialon_client_profile type user profiles
dynamic-access-policy-registration DfltAccessPolicy
wialon_1 Wy2aFpAQTXQavfJD username encrypted password
wialon_2 4STJ9bvyWxOTxIyH encrypted password username
remote access to Wialon tunnel-group type
attributes global-tunnel-group Wialon
address pool Pool_139
Group Policy - by default-GroupPolicy_Wialon
tunnel-group Wialon webvpn-attributes
enable Wialon group-alias
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:447ec315ae30818a98f705fb1bf3fd75Hello
You don't have NAT exemption the DMZ network to the pool of VPN traffic.
Please try to add the following statement to run:
nat (DMZ,outside) 1 source static any any destination static NETWORK_OBJ_139.16.1.0_25 NETWORK_OBJ_139.16.1.0_25 route-lookup
Also please delete the existing instruction manual nat "non-proxy-arp" statement, because it can cause problems like you the ip subnet address pool is identical to that of the Interior of the network.no nat (inside,outside) source static any any destination static NETWORK_OBJ_139.16.1.0_25 NETWORK_OBJ_139.16.1.0_25 no-proxy-arp route-lookup nat (inside,outside) 1 source static any any destination static NETWORK_OBJ_139.16.1.0_25 NETWORK_OBJ_139.16.1.0_25 route-lookup
Cordially Véronique -
The remote VPN Clients and Internet access
I apologize in advance if this question has already been addressed. I am currently using a PIX Firewall Version 6.1 520 (2) running. I have several remote users that VPN for the PIX. Once the VPN tunnel is started, they are more able to connect to internet from their local computers. Is there a configuation on the PIX that allows remote users to have access to the internet when you are connected to the PIX.
TIA,
Jeff Gulick
The Pix does not allow traffic enter and exit on the same interface. Therefore, a VPN user cannot access the Internet through the tunnel. If you use the Cisco client, enable tunneling split so that all traffic through the tunnel.
If you use PPTP, you can turn off the option that makes the remote network, the default gateway. However, local routes should be added to these clients when they connect.
Or you can use an additional interface on the firewall. One that puts an end to VPN tunnels and another providing for Internet connectivity. In this way the traffic is not enter/leave on the same interface.
Of course, it is preferable if the customer Internet traffic does not go through the tunnel. It wastes your bandwidth and has security problems as well. I suggest you use the client to Cisco and the split tunneling.
-
Inside the server can't ping remote vpn client
My simple vpn client can accumulate the tunnel vpn with my Office ASA5510 success and my vpn client can ping the internal server. But my internal server cannot ping the remote vpn client. Even the firewall vpn client windows is disable.
1. in-house server can ping Internet through ASA.
2 internal server cannot ping vpn client.
3 Vpn client can ping the internal server.
Why interal Server ping vpn client? ASA only does support vpn in direction to go?
Thank you.
Hello
Enable inspect ICMP, this should work for you.
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the icmp
inspect the icmp errorinspect the icmp
To configure the ICMP inspection engine, use the command of icmp inspection in class configuration mode. Class configuration mode is accessible from policy map configuration mode.
inspect the icmp
HTH
Sandy
-
A VPN client / ASA cannot access the Internet.
VPN clients can get to the servers internal/DMZ but not Internet. This is the partial config of the SAA. TIA
Pool VPN 10.17.70.0
DMZ 192.168.100.0
172.0.0.0 internal
-------------------------------------
nonatdmz list of allowed ip extended access any 192.168.100.0 255.255.255.0
access extensive list ip 172.0.0.0 nonatdmz allow 255.0.0.0 10.17.70.0 255.255.255.0
standard access list splittunnel allow 172.0.0.0 255.0.0.0
Global interface (10 outside)
Global interface (Businesspartner) 10
NAT (inside) 0-list of access nonatdmz
NAT (Inside) 10 0.0.0.0 0.0.0.0
NAT (DMZ) 10 0.0.0.0 0.0.0.0
Vinnie, happy that you have found here.
Telnet for asa by vpn session, you need to add this statement.
management-access inside
In this same connection see split tunnel vs local Allow only lan access, you can learn the differences and you will better understand your configuration asa related to ra vpn.
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080702999.shtml
-
Remote VPN client and Telnet to ASA
Hi guys
I have an ASA connected to the Cisco 2821 router firewall.
I have the router ADSL and lease line connected.
All my traffic for web ports etc. of ADSL ftp and smtp pop3, telnet etc is going to rental online.
My questions as follows:
I am unable to telnet to ASA outside Interface although its configuered.
Unable to connect my remote VPN Client, there is no package debug crypto isakmp, I know that I have a nat that is my before router device my asa, I owe not nat port 4500 and esp more there, but how his confusion.
I'm ataching configuration.
Concerning
It looks like a config issue. Possibly need debug output "debug crypto isa 127".
You may need remove the command «LOCAL authority-server-group»
NAT-traversal is enabled by default on the ASA 8.x version. So you don't have to worry about NAT device in the middle.
-
Remote VPN with PIX without access to the local network
Hi @all,
I ve running into problems and I have not found any solution. Can someone check my config?
Facts:
PIX 501 6.3 (3)
4.04 VPN client
Wanted solution: access to HO via VPN
VPN tunnel will be established, I get an IP address, but I can´t the systems behind the pix and the pix of access itself.
To the VPN Client Staticts, I see outgoing packets, but no entrant (if I send a ping to peer behind the pix)
I hope someone can help me
Attached is my config:
PIX 501 and 506/506e pix are not supported in v7 due to the fact that the cpu is not able to deal with the extended features of v7.
PIX 520 is not supported I guess it's because of the fact that the model is discontinued.
-
VPN client can get the gateway?
I have a question for a long time.
Cisco vpn client will find a gateway to the remote vpn server address.
There are many situations in which we need a gateway assigned to the vpn client. If the customer can freely access all private networks.
PIX of Cisco router has this feature?
Why the customer would need a bridge tunnel?
The customer already has a gateway of the ISP.
Once the tunnel is up, if not to do split tunneling, all customer traffic will be sent on to the CONCENTRATOR's IPSec tunnel. So, indeed, the HUB is the default gateway.
If you use the split tunneling, then your ACL will say what customer traffic must be encrypted on the tunnel on the hub. All other traffic is sent clear for the ISP. So, indeed, the HUB is the gateway for the LAN within the tunnel.
There is a featur default on the 3000 gateway Tunnel, but that's for a different purpose
-
VPN traffice is not going outside network
I can connect to my home virtual private network and access to trade, share network, ect, however, when I open a Web page or anything that needs and outside the intellectual property that I can't get out. As soon as I log out of the excellent work VPN client of web pages. Any suggestions?
Cisco PIX Firewall Version 6.3 (3)
Material: PIX - 515, 32 MB RAM, Pentium 200 MHz processor
Thanks in advance... Mike
I would try using a different acl for your tunnel of split, it is always advisable to separate your ACL.
vpngroup split tunnel 102 touavpn
access-list 102 permit ip 10.10.12.0 255.255.255.0 10.10.15.0 255.255.255.0
access-list 102 permit ip 10.10.11.0 255.255.255.0 10.10.15.0 255.255.255.0
access-list 102 permit ip 10.10.101.0 255.255.255.0 10.10.15.0 255.255.255.0
access-list 102 permit ip 10.10.14.0 255.255.255.0 10.10.15.0 255.255.255.0
I would also get rid of what you don't need...
IP 10.10.15.0 doesn't allow any access list 101 255.255.255.0 10.10.12.0 255.255.255.0
-
IPsec remote VPN client 5.0.07 Cisco
Hello
I am setting up remote IPsec VPN using ASDM for ASA 5505.
can someone guide me for FOLLOWING;
1 step 6 for ASDM IPsec wizard: name of the cluster: what IP addresses I need to assign here.
my network has inside the IP 192.168.0.1 and outside IP 162.212.232.174
2. VPN client: what would be the IP host?
What is the password and username for authentication group?
Please advice or give me a link that can help me for this set to the top?
I need help with installation of VPN client both ASDM for IPsec Wizard wizard.
Thank you
SAP
Hello
Pool is the range of IP addresses for VPN clients (when connect you to your network). Use a different subnet of your internal networks. ex: 192.168.10.0 255.255.255.0
Host IP: your ASA 5505 public ip: 162.212.232.174
Group information - that you configure on ASA5505 and even he must be configured on the client.
See the link below (research online and you will find a lot of documentation).
http://www.databasemart.com/HOWTO/Cisco_VPN_Remote_Access_Setup_ASA5500.aspx
THX
MS
-
Reverse road injection for remote VPN Clients
Hello world
you will need to confirm if reverse road injection is used only for Site to site VPN?
Also to say that we have two sites using site-to-site vpn
Site A Site B
Private private IP IP
172.16.x.x 172.20.x.x
Now, as we VPN site to site, we can either activate the NAT - T option which will allow 172.16 IP reach site B as 172.16 only.
Do not change the IP address.
Option 2
IF we don't allow NAT - T and if we allow injection road Revese and we use say Protocol ospf on ASAs in site A and B.
In this case, we allow IPPS so that we can announce the private road 172.16. on the internet right of site B?
Concerning
MAhesh
Hello Mahesh,
"Reverse road injection (RRI) is used to fill in the routing table of an internal router that is running OSPF Open Shortest Path First () protocol or the RIP (Routing Information) protocol for Remote Clients VPN sessions or a local area network LAN."
As a result, allowed RRI ASA learn routing information for connected peers and advertising via RIP or OSPF.
NAT - T is automatically detected and used when the local or the remote peer is behind NAT.
To answer your question:
If NAT - T is required and enabled, then it will automatically be used peer VPN. Then, with IPP in place, remote network will be added to the routing as static routes table, so they can be advertised by OSPF.
HTH.
Please note all useful messages.
-
VPN client with overlapping of private networks?
I have a new client who needs to send us data occasionally, we normally install the Cisco VPN Client on their PC, but this client has the same private network, we.
I know, but it could be done with policy NAT on my 5510 ASA with a VPN site-to site, the customer does not want to change the address or network hardware. They have router cable with no VPN option, and they are unwilling to spend more money on this project.
Can this work if there is no overlapping of IP addresses?
Your ACL SHEEP overlaps the static NAT and SHEEP has priority over the static NAT strategy strategy, why it does not work.
Please kindly remove the following:
access-list extended sheep allowed ip 192.168.1.0 255.255.255.0 192.168.240.0 255.255.255.0
-
Cisco VPN Client anything cannot access through VPN on an ASA5505 8.4
Hello
Completely new to Cisco ASA and the need to get this working ASAP.
8.4 (1) ASA 5505 is the secondary FW and I need to authorize all out and block everything coming, but for the VPN clients. Since a jerk of Cisco, I used the ASDM and it's sorcerers to make this work, which may explain my situation.
192.168.101.0/24 is the local network
192.168.101.5 is the IP of ASA
192.168.101.2 is the primary FW (and the default gateway for servers, I have to access through the VPN)
10.10.101.0/24 is the VPN IP range (this can be what you want, I'm not married to it somehow)
My Cisco VPN Client connects to the ASA and receives 10.10.101.1 IP address, but I get no connectivity to the ASA or any other 192.168.101.x or service server (tried RDP, telnet, ping, etc.)
Configuration file is attached.
Help pretty please!
Thank you.
Did you add a route for the VPN Pool on the main firewall to the ASA?
Best regards
Peer
Sent by Cisco Support technique iPad App
-
SonicWALL NSA, using VPN client overall comments to reach network of internal resources
Hello
I have problems performing Global VPN client to work when you connect to our internal network of comments in order to reach our internal LAN Server in order to reach internal resources in a safe manner. I'm not sure what could the settings were necessary in the Sonicwall to achieve?
Our installation is based on the NSA 3600 and I installed a WLAN area in the sonicwall to enable clients to connect to the internet. Traffic in the WLAN area to our internal LAN Server is denied. However, some users would like to be able to use the wireless network in order to achieve internal resources and for that I want to use the Global VPN client. It is even possible to use of an internal network from the point of view Sonicwalls Global VPN client?
The use of the outside Global VPN client works very well
Any help is greatly appreciated and if more detailed configuration information are necessary, I'll happily give you that.
Thank you
Hi Ben,
No I didn't at first, but your answers have would lead me in the right direction, hopefully. I realized that I could create a custom GroupVPN by going to the settings of the interface to the interface that is the war in the Gulf to my wireless network.
return to results
Thank you
Cree
-
Remote VPN users cannot reach OSPF Inter networks
Hi all
Area0 & Grenier1. Grenier1 ASA has remote VPN configuration where users also use split tunneling. When the VPN plug-in users, accessing all respurces successfully in the area euro1, but unable to reach Area0 resources.
But Area0 PCs can 'ping' on addresses IP VPN component software plug-in. I tried 'debug icmp trace', but not poping up even one message upwards all to initiate the 'ping' of the computer laptop VPN users.
FYI... Grenier1 N/w: 10.251.0.0/16 and 10.251.40.0/24 has been used for VPN DHCP users. Everything works well except for the Area0 accessibility.
Any suggestions... ?
Thank you
MS
access-list extended sheep ip SiteA 255.255.0.0 255.255.255.0 SiteAVPN allow
access-list extended sheep ip SiteB 255.255.0.0 255.255.255.0 SiteAVPN allow
Maybe you are looking for
-
POP account has stopped receiving
My POP email account stopped receiving messages after an upgrade of the server. Sending works fine. I had another account on that server that also has ceased to receive messages (send also worked well) and I had to delete the account and start again,
-
I log every 0.5 seconds in a txt file. When I need to store more values that I have in this VI structure will be very little claire. Is there a better way for the logging of data?
-
Hello. I would like to install a gtx 580 zotax or zotax gtx 460 on my PC. ..HP p6 2021itCard mother foxconn h61 2abfI7 2600 (sandy bridge), Lga 11558 GB ramIn fact gt 545/3 gbPU 2 GTX work on my motherboard?Thank you
-
System DLL user32.dll was moved in memory can someone tell me how to solve this problem
System DLL user32.dll was moved in memory, I'm running Xp 32 bit can someone tell me how to solve this problem
-
The connection to the server has failed. Account: 'mail.hughes.net', server: 'mail.hughes.net', Protocol: POP3, Port: 110, secure (SSL): no, Socket error: 10060, error number: 0x800CCC0E can you all help me to solve this problem?