Removal of blackBerry Smartphones send using accounts on Blackberry 9780 calendar

Similar Questions

• BlackBerry Smartphones sending Emails using different addresses

  I use gmail and I have all of my other addresses before their mail to my gmail account. However saw only my gmail on my blackberry account I cannot respond to the messages by using the e-mail address they were sent too. This example gets confused professors sometimes when they send something to a school email address and get a response from a very different gmail address. Is there a way I can just receive e-mails from my account gmail on my blackberry but still send emails using all my addresses. Help, please.

  No, not exactly.

  One, your system to redirect other accounts on the single account is not the best set upward after all. You could have all of his accounts pushed directly to the unit, unless there is some overiding issue prevents you from doing it. This configuration would allow ease of response from the same account to which it was sent.

  On a BlackBerry, he will answer ONLY to the account to which the e-mail was sent. You can't change that, and we can 'send using' an e-mail account, you have pushed to the device, which is logical.

  However, in your configuration of BIS, where you have enabled the gmail pushed to your BlackBerry, you can define a section of ' answer to "where you can enter your school account, or whatever that you choose. This will not change the sending account, but it will give an appropriate response to the address.

• Is it possible to blackBerry smartphones can remove the BBM5.0 when using OS5.0?

  Is there a way to remove the BBM5.0 when using OS5.0? I tried using DM6.0 but BBM is marked as a component of basic impossible to remove.

  I hate BBM in general because it is always on. I don't want to install an older version.

  If anyone can help me, thanks in advance.

  lusilveira wrote:

  Is there a way to remove the BBM5.0 when using OS5.0? I tried using DM6.0 but BBM is marked as a component of basic impossible to remove.

  I hate BBM in general because it is always on. I don't want to install an older version.

  If anyone can help me, thanks in advance.

  • with a few OSes 5.0.X.X, BBm is a basic application and cannot be deleted.
  • BUT the other OSes, the BBm 5.0.X.X became an addon application and can be removed. (i.e. 5.0.0.43 6 and 5.0.0.462)

  If you have the first category OS, I suggest you try and install BBm for example using AppWorld. Perhaps by upgrading BBm, it will become an add-on.

• E-mail account do not send or receive e-mail. ' - ERR [IN USE] account is locked by another session or for maintenance, try again. »

  Account: ' pop.charter.net (2) ', server: 'pop.charter.net', Protocol: POP3, server response: '-ERR [IN USE] account is locked by another session or for maintenance, try again.', Port: 110, secure (SSL): no, Server error: 0x800CCC90, error number: 0x800CCC92

  original title: refuses to send/receive e-mail

  Well, you can't always believe them.  Try to remove your e-mail account, and then verify that you do not have interference antivirus (see www.oehelp.com/OETips.aspx#3) then compact and repair the database of WinMail (www.oehelp.com/WMUTil/) and add your account back once again and see if that makes a difference.  Also, make sure that you are checking in not too often (like every 2 minutes) for mail (Tools |) Options).

  Steve

• Elements removed from blackBerry Smartphones

  How can I recover the items removed - some of them have been entered recurring in my calendar.

  is there a folder deleted items and if so how can I get accesss it

  Unless you have data in a backup, or these same elements are still on your PC where you can perform a synchronization to recover them, there is no way to retrieve what you deleted from your device.

• Why this keep happening ' unusual use - account temporarily locked Down?

  This problem just started. It's happened twice in five days. I ' did no unusual activity and don't understand why I'm locked out of Firefox. Any help will be greatly appreciated.

  Thank you.

  Bluesdrummer

  I think it's a message from Google, so I think that you have Google start page or your extension Gmail notify immediately access your Google account and send this message.

  Could check you the suggestions in these discussions of support for Google:

  • Help of use - account temporarily locked down - unusual! -Forums of Google products
  • "Unusual use - account temporarily locked down" twice in 24 hours (after sending emails only 3)-Forums of Google products

• Impossible to send using windows live mail with on restart my computer everytime, error 0x800CCC0F

  Impossible to send using windows live mail with on restart my computer every time.   I use broadband services, but they say it is not their problem

  It started a month ago.   Whenever I try to send an email using windows live mail, I get a failure;

  Your server suddenly put an end to the connection. The possible causes for this include server problems, network problems, or a long period of inactivity.

  Subject ' Fw: Snowplow '
  Server: "smtpout.secureserver.net."
  Windows Live Mail error ID: 0x800CCC0F
  Protocol: SMTP
  Port: 80
  Secure (SSL): No.

  Anyone have an idea where to start.

  Server: "smtpout.secureserver.net."
  Windows Live Mail error ID: 0x800CCC0F
  Protocol: SMTP
  Port: 80
  Secure (SSL): No.

  Anyone have an idea where to start.

  Start with this Port number.   Port 80 is usually reserved for HTTP.    Try the 25.

  Unless your host secureserver.net says something, otherwise...

  Oh.  They do it?  But no information for WLMail, so you have to adapt...

  http://products.secureserver.NET/email/email_thunderbird.htm

  (BING search engine for)
  Site: secureserver SMTP .net
  )

  In particular, I think, note this:

  NOTE: "smtpout.secureserver.net" is a relay SMTP server. To use this server to send e-mail messages, you must enable SMTP relay on your e-mail account. Connect to your management page email accounts to set up SMTP relay. If you have not set up SMTP relay and allows it to your Internet Service Provider (ISP), you can use the server of mail from your Internet Service provider. Contact your Internet service provider for this setting.
  

  BTW if you use WLMail.exe you can also try to get help from the WLSC through its Mail Portal

  http://windowslivehelp.com/product.aspx?ProductID=15

  Good luck

  Robert Aldwinckle
  ---

• Add or remove destinations in the send to box after right-clicking on the programs.

  is it possible to add or remove destinations in the send to box? I have a program called it Konvert which I deleted via my progs add/remove from the past few months and I would like to add a wave converter program called Switch order to convert MP3 to Wav. I could then send the direct file.

  I don't know that you can do.

  With regard to your audio converter...
  I also Switch. As you already noticed, convert to Wav format is going to explode the size of the file. I say good shot upward.

  Here's a program a lot better a lot, a lot, for audio conversion. 'S called it CDex.
  He keeps the SAME size of file in WAV format mp3 *.
  It is extremely useful to electronic music or email delivery of PowerPoint presentations with music files integrated.

  Here is the link: http://cdexos.sourceforge.net/?q=download
  I use 1.70 beta 2 for more than 2 years now. I have demonstrated with version 1.5. (My OS is Vista Home Premium)
  If you are not comfortable with the word "beta", use version 1.5.

  t-4-2

• programmatically, select Send using email address

  Hi all

  I would like to write that an application with function can allow the user to select the default send using e-mail address. Anyone have idea?

  Thank you for your attention and help

  Hello

  If you change to change the default mail setting, you can use the following code. Hope you find it help

  Public Sub SendMessage() throws IOException, MessagingException

  {

  Store store = getStore (email from one of the registered e-mail);
  Records file [] = store.list (Folder.SENT);
  Folder sentfolder = files [0];
  Message msg = new Message (sentfolder);
  msg.addRecipient (net.rim.blackberry.api.mail.Message.RecipientType.TO, address);

  msg.setSubject ("Subject");
  String body = 'Something';
  msg.setContent (body);
  Transport.Send (MSG);

  }

  Public Store getStore (String regEmail)
  {
  Full book sb = ServiceBook.getSB ();
  SRS [] ServiceRecord = sb.getRecords ();
  for (cnt int = srs.length - 1; cnt > = 0; cnt-) {}
  If (srs [cnt] .getCid () .equals ("CMIME')) {}
  ServiceConfiguration sc = new ServiceConfiguration (srs [cnt]);
  If (SC. GetEmailAddress(). Equals (regEmail))
  {
  Store is Session.getInstance (sc) .getStore ();.
  store return;
  }
  }
  }
  Return Session.getDefaultInstance () .getStore ();
  }

• BlackBerry Smartphones BlackBerry 9780 - screen early failure - what should I do?

  I have a BlackBerry 9780 which I bought from a friend who has improved his own phone.

  I would have gone directly to a BlackBerry of any sort of tesco on contract, but the situation at the time made it difficult.

  I started my contract with O2/Tesco with a Samsung BlackBerry look-alike.  A few weeks later, I bought a BlackBerry PlayBook and realized that get t as the most out of that I also had to have a BlackBerry phone.  Tesco wouldn't let me exchange the samsung I have been more than a month in contract with another 23 months to go.  Then buy the 9780 at my companion, it was really the only option.  Tesco sorted guys my BlackBerry connection for me - fair play to them, they were superb!

  I gave the wife the Samsung!

  The 9780 has been great.  I've used it since about January/February of this year.  My companion had sent it to a repair/refurb, (of course, the central navigation button was faulty), before it was sold to me.

  I noticed that there is a small area that was black on the screen, it looks a bit like a diagram of rorschash, (it is the best way to describe it).  I happened to be in the other day from Maplin and I showed it to a guy who seems to be very well informed.

  He believes that the screen is depixelling or words to that effect.

  I need it to last at least 18 months until my contract is in place, and then I'll renew and get another.

  What is the best couse of action?

  Hello

  as far as I know, the dead pixel or black spots will be little bit greater over a long period of time.

  9700 & 9780 are tough phones, is one of the best Blackberry produced, but he has a weakness

  that is the screen / lcd screen. Sometimes, it gives you a black spot, dead, blank screen of white or black blankscreen pixel.

  the replacement are normally made in China, they have different qualities.

  so make sure that if you take it to a local repairman, you are given a minimum of two weeks guarantee

  It is only a 2 minute job for replaces it, simply remove the 6 screws and 2 clips

  but the problem is that sometimes you do not get a good replacement.

  Once I tried 5 screens before I get a good.

  and once you use a replacement screen, ready to be replaced again after 4 to 6 months if your unlucky.

  Here's how its done

  http://www.YouTube.com/watch?v=t2xkr15QQkY

• Is it possible to send Radius accounting packets with two different servers?

  Hello experts!

  I have dilemma I send info Radius accounting on two different servers for authentication of the dot1x. Here are the relevent config. However the switch just to send a copy on the first server in the server group...

  RADIUS AAA server Acct group
  ACCT-port of the server 172.17.1.1 auth-port 1812 1813
  ACCT-port of the server 172.17.1.2 auth-port 1812 1813

  accounting dot1x default start-stop broadcast group AAA Acct

  RADIUS-server host 172.17.1.1 auth-port 1812 acct-port 1813 key xxxxxx
  RADIUS-server host 172.17.1.2 auth-port 1812 acct-port 1813 key xxxxxx

  Is it possible to send two copies of two different servers? I tried the key word 'issue' in the aaa accounting command, but it does make a difference. What is doing? I can't find it in the manual...

  Thank you!

  Difan

  Difan,

  You must create two aaa server groups to operate. Allows the sending of accounting records to multiple AAA servers.  At the same time returns accounting records the first server in each group. If the first server is unavailable, the failover occurs using servers defined within this group.

  Accounting AAA broadcast configuration
  The following example shows the turn on broadcast accounting using the aaa accounting global command:

  RADIUS AAA server group isp
  Server 1.0.0.1
  Server 1.0.0.2

  AAA isp_customer radius server group
  Server 3.0.0.1

  AAA accounting network default start-stop broadcast group isp group isp_customer

  host server RADIUS 1.0.0.1
  host server RADIUS 1.0.0.2
  Server RADIUS key key1
  RADIUS-server host 3.0.0.1 key2 keys

  The broadcast keyword causes the start and stop accounting for dot1x connections to be sent simultaneously to the 1.0.0.1 group isp server and Server 3.0.0.1 in the isp_customer group. If 1.0.0.1 is unavailable, Server failover 1.0.0.2 occurs. If the 3.0.0.1 server is unavailable, no failover occurs because backup servers are not configured for the isp_customer group.

  Kind regards

  ~ JG

  Note the useful messages

• BLACKBERRY Smartphones blackBerry 9780

  Friday (May 6, 2011), I've upgraded to a BlackBerry 9780.

  May 11, 2011, I handed the phone to Vodacom Westgate J as it was freezing and does not make or accept calls. Phone shows full signal and the name of the network.

  They sent to Cresta to repair.

  May 17, Westgate Vodacom has replaced with a new phone.

  On 19 may, I showed Vodacom Westgate as the phone again had the same problem as the old. We turned off the phone and he did and accepted calls.

  May 22 I had to reboot the phone to use it.

  On May 23 I talked to Vodacom Westgate and they said I can bring the phone and they will send it.

  This morning may 24 I handed the phone to repair and he was again sent off for six days? s.

  Now, someone has a theory and that the problem with my sim card (a card that works in my HTC, my previous Nokia and Ericsson, all smart phones).

  Nobody at Vodacom can give me South Africa Blackberry contact numbers so that I can tell them that I think they are dumping obsolete phones on us.

  And thinking that Blackberry users think that it's the best thing since Jell-o was invented, wait until they get their hands on the BlackBerry 9780 and find it is the closest thing to hell.

  You bet that BlackBerry 9780 is a dud, but you want to keep under wraps because you're afraid of losing customers

  insurex wrote:
  And thinking that Blackberry users think that it's the best thing since Jell-o was invented, wait until they get their hands on the BlackBerry 9780 and find it is the closest thing to hell.

  You bet that BlackBerry 9780 is a dud, but you want to keep under wraps because you're afraid of losing customers

  You bet you're wrong. It really is the best thing since sliced bread. The Frost is past.

  During your registration to this Forum, and when you have accepted the EULA, you would have noticed that specific to the notice that it is a community of users support forum. We are not be used RIM/BlackBerry. We are users like you (well, not exactly like you) who love to help others get the most out of BlackBerry, because 90% of problems are often questions of the user that can be fixed with a click or two on an option.

  So, your SIM card that works in your Nokia, HTC and Ericsson... you should get the NEW card SIM of Mr. J Vodacom Westgate, or they should just trade for you. The 9780 is quite a bit more advanced that the devices that you have named, and the SIM card must also be the latest they have. Even though a lot of SIM cards are similar, it is separate technical differences between even all SIMs that are rated as 3 G SIMs, because as a technology, then make the SIMs.

  I get the camera back that you gave to, or require a new unit. There is absolutely NO reason to send a new unit less than a month, to make repair. Most likely, he needs a new SIM card, and/or upgrade the operating system to the latest official version.

  As you bought the device of Vodacom, your contract for technical and warranty support is with Vodacom, who then will escalate issues to support technical level RIM. If they don't you should ask. It isn't a phone number to call, he will manage the transfer and climbing.

  If you need help with the software upgrades, ask to your, we will help. Just to come here to complain won't get you anything other than get it off your chest. If you don't want, done.

  Good luck.

• How to remove the variable created when using definedNamedWhereClauseParam()

  Hello
  
  My Jdev version 11.1.1.7.0.
  
  I'm Executive where clause programatically where I need to bind two bind parameters under certain conditions. Example, I have two bind variables X, Y.
  
  Here's the problem:
  
  Assume that the first time I'm setting one variable X, so I define X bind variable and execute the query.
  
  What second time I send only Y but not X. In this implementation of the scenario of VO throw an exception, given that the variable X is already created in the VO object and where clause does not have this setting.
  
  So how to remove variables created in the original Version all in definedNamedWhereClauseParam(). I need to erase what ever the previously created variable every time I execute method.
  
  I can make the similar functionlity using setWhereClauseParam (using literals). But I have a few technical restrictions for use.
  
  Could you please help me how to remove the variable before vo using definedNamedWhereClauseParam.
  
  Caused by: java.sql.SQLException: try to set a parameter name that does not intervene in the SQL: itemNumber
  at oracle.jdbc.driver.OraclePreparedStatement.setObjectAtName(OraclePreparedStatement.java:15969)
  at oracle.jdbc.driver.OraclePreparedStatementWrapper.setObjectAtName(OraclePreparedStatementWrapper.java:911)
  at weblogic.jdbc.wrapper.PreparedStatement_oracle_jdbc_driver_OraclePreparedStatementWrapper.setObjectAtName (unknown Source)
  at oracle.jbo.server.OracleSQLBuilderImpl.bindParamValue(OracleSQLBuilderImpl.java:4669)
  at oracle.jbo.server.BaseSQLBuilderImpl.bindParametersForStmt(BaseSQLBuilderImpl.java:3687)
  at oracle.jbo.server.ViewObjectImpl.bindParametersForCollection(ViewObjectImpl.java:22742)
  at oracle.jbo.server.QueryCollection.buildResultSet(QueryCollection.java:1298)
  ... more than 96
  
  
  
  Thank you.
  
  -Diette.
  
  Published by: Vidya Diette on February 28, 2013 08:43

  Hello

  You need access to the variable Manager. Order of reading in the JavaDocs:

  http://docs.Oracle.com/CD/E28389_01/apirefs.1111/e10653/Oracle/JBO/ViewObject.html--> http://docs.oracle.com/cd/E28389_01/apirefs.1111/e10653/oracle/jbo/VariableManagerOwnerBase.html#getVariableManager%28%29--> http://docs.oracle.com/cd/E28389_01/apirefs.1111/e10653/oracle/jbo/VariableValueManager.html--> http://docs.oracle.com/cd/E28389_01/apirefs.1111/e10653/oracle/jbo/VariableManager.html#removeVariable%28java.lang.String%29

  Frank

• Satellite A500-1GL: it is advisable to remove the battery when you use the network

  I know this is a silly question but its actually something I know not so thought I would ask.

  I almost always plug my laptop into the supply line (satellite a500 1gl)
  I was wondering have you actually keep the battery installed even when using the electrical network.
  Or is it really advisable to remove the battery when you use the network?
  I didn't know if the battery should always be in place.
  Thanks for your help
  Torti

  Hello

  A few years ago it was recommended to remove the battery of the laptop if the AC adapter is plugged. What keeps the constant charge battery
  New age of batteries are better you can leave the battery in the Bay it s ok and it should not affect the performance

  However, sooner or later each battery would die it s only a matter of time, you know

• Satellite A660-k17: can I remove the two primary partitions used for restoration?

  Hello
  I have 3 questions :) #.

  1. I burned a copy dvd recovery media, on a laptop A660 k17. There are two partitions on the disk that I think are there for the recovery. The first is 1.46 GB and it's for the recovery and another partition hidden 8.29 GB... and I think that the first contains the Recovery Wizard and the whole environment in which we will get through the repair of the system and the hidden disk contains the actuall with windows data, drivers and so on. Can I remove these two? I ask mainly on the first, if it is not necessary for the system to boot or something after that I have to recover the laptop to the factory setting.

  2 and I also want to leave my partitions so that I don't have to partition the whole drive from C 600 GB again. I have a D drive created but there is this response to a topic already in the forum http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=64754&tstart=90
  who says that when I leave the partitions I created myself, that the recovery will be not available. I have a copy on dvd, but only to make sure no kidding something upward.

  3. when I want a clean system without some software which are preloaded on the oem recovery disk... I have to use windows recovery? or it will be the same as the toshiba one?
  Thanks for the reply possible :)
  Beautiful day :)

  > Can I remove the two primary partitions used for restoration?
  First not, but you can remove the Toshiba recovery partition if you created the recovery DVDs. One day, if you want to install the recovery image once again you can use created the recovery disc.