Replace the drive DVD/CD-RW on my Satellite Pro A40

Similar Questions

• It is Possible to replace the drive DVD Bluray for HP Pavilion dv6-6176sx

  Hi all

  It is Possible to replace the DVD Bluray for HP Pavilion dv6-6176sx notebook PC Player?

  Thank you

  Of course it isn't yet very difficult. You just need a BR drive or a drive? The replacement drive will be $80-120, or so, maybe a little less. You can find them on eBay. You can use a generic but that may require a redesign of the front or just get a car dv6-6000 BR on eBay. Trade on with a few screws on the bottom. Get out and drag the replacement. You will need new software to play BR movies, of course.

  Post back with any questions

• You are looking for an internal DVD drive for a Satellite Pro A40

  Hello

  I'm looking for an internal DVD burner for a model Satellite Pro A40 2.88 Celeron with a currently installed CD-RW/DVD-Rom. My mother is the owner of this laptop and I want to upgrade the drive for her.

  Does anyone here know of any number of model of the DVD-RW/CD-RW/DVD-Rom that is compatible with this model.

  I want the drive to function as a DVD-Rom/CD-RW also because I do not want to lose these features. Swap the bezel above if necessary isn't a problem for me.

  Thank you

  Hello
  For this particular model, I could not find another A40 Pro which has a DVD - RW, only DVD ROM. I also suggest to buy an external DVD - RW writer because an internal hard drive will cost much more. Probably triple what external there. External, you can find for about 50 but internal will cost at least about 90 more taxes. I'm sure it is internal that correspond to this machine, but at the moment I don't have the time to research each compatible model search of the car, it's why I suggest an external drive. I hope this helps.

• Re: Satellite A100-692 - how to replace the CD/DVD drive?

  Hello

  the device DVD/combined my A100-692 is damaged and I want to replace it.
  I found no still no guide how to replace the unit.

  Is there something available?

  Thanks in advance!

  Hello!

  AFAIK, you must remove the keyboard first, before you can replace the CD/DVD drive. Remove the screws on the lower side, and then you can push the disc if you have replaced the keyboard.
  It seems to be a bit tricky

  Maybe you should ask a technician for laptop to help. They can replace the CD/DVD drive for you.

  Good bye

• Can satellite A100-097 - I replace the cd - dvd drive

  Hello

  The cd-burner in my Satellite A100-097 drive begins to age, burns can sometimes fail, sometimes cannot even read simple audio cds.

  Can someone tell me if I can replace it with a new and where to find it, finally?

  Thank you
  Andrea

  Hello

  Yes, you can replace the CD/DVD drive with a new one.
  But be aware that not all of the sides are compatible due to different master/slave/c-salt settings

  Manual of use you should find some details about compatible readers and supported
  Check it out
  If you have no user manual then go to the Toshiba European page to download.

  In addition, you can buy a player of an ASP supported in your country
  The guys would be able to order it at Toshiba if necessary.

• Replace the CD/DVD on HP dv6-1375 drive

  I need to replace the CD/DVD drive on my laptop HP dv6-1375.

  1. where can I find instructions to do

  2. what type of replacement Player DVD should I look for?

  Thank you.

  Anderson2244 wrote:

  I need to replace the CD/DVD drive on my laptop HP dv6-1375.

  1. where can I find instructions to do

  2. what type of replacement Player DVD should I look for?

  Thank you.

  1: http://www.google.co.uk/url?sa=t&source=web&cd=17&ved=0CEsQFjAGOAo&url=http%3A%2F%2Fbook-lab.ru%2Fpdf%2Fhp%2Fservice-manual-HP-Pavilion-dv6.pdf&rct=j&q=dv6-1000%20service%20guide&ei=Uo0bTuC6H4W1hAfU-8XQBw&usg=AFQjCNG4NdQy2zsDK_FO3cdDxICdGdQA2g&sig2=B-XtVxEO3fKl7C-mrF6EWA

  See page 57...

  2:

  Blu - ray ROM DVD±R/RW SuperMulti Double Layer drive Ref: 511881-001

  Blu - ray ROM with LightScribe SuperMulti DVD±R/RW Double Layer drive Ref: 511882-00

  Drive SuperMulti Double layer Combo Drive ref: 511880-001

  The DVD rom on ebay

  http://CGI.eBay.co.UK/HP-GSA-T50L-SATA-DVD-RW-odd-511880-001-/260776306069?PT=PCC_Drives_Storage_Internal&hash=item3cb77aa595

• Replacing the CD/DVD with SSD

  Hi, I have a mid-2009 13 "Macbook, and I plan to replace the CD/DVD drive (which it doesn't) with an SSD, instead of replacing it with a new CD player.

  I would move so that OSX and software on the new SSD, leaving other data on my main hard drive. I read that the best solution is to install OSX on the SSD from scratch, since migration it seems impossible, but how then I could remove the 'duplicate' old of my HDD main OSX?
  The entire migration process is not quite clear to me, I wouldn't mind some step by step instructions.

  Thank you in advance!

  1st, I did it on an iMac, so I went through it.

  You can use a utility cloning as Carbon Copy clone (demo fully active 1 month) or SuperDuper free (free for a full clone) to move your boot disk for SSD and it will be fully functional.  In my case, I used Carbon Copy Cloner.  It is even technically possible to use the Applications-> utilities-> disk utility-> restoration as a means to clone the drive, but I find it cumbersome.

  <http://www.shirt-pocket.com/SuperDuper/SuperDuperDescription.html>

  <https://www.bombich.com/>

  I think you could also just restore a backup Time Machine for the SSD as well (although I did not do that, so I don't know the details).

  You can do a clean install and get rid of any cruft you've accumulated over the years and then install only the stuff that you are currently using.

  Or you could do a clean install and then use the Applications-> utilities-> Migration Wizard move above specific categories of files of initial startup disk.

  After you have the SSD running with your software on it, consider allowing TRIM

  <http://www.imore.com/os-x-10104-and-trim-support-should-you-turn-it>

  I used OWC <http://MacSales.com> kit data-Doubler to replace my iMac DVD by an SSD.  They provided everything I needed.  I chose a kit including the tools I needed.  I also watched the OWC installation videos, as well as on YouTube to become familiar with the installation.  And I had a copy of the instructions to disassembly <http://iFixIt.com> and images to print for reference, while doing the installation.  I would have recorded any screws that I removed the instructions that told me to remove that screw then I would make sure I would put the correct screws into the appropriate holes.

• Satellite X 200 and replace the HD-DVD player

  G ' Day

  I'm looking to replace the HD-DVD drive in my Toshiba X 200 (PSPBUA-00N007) with a Blu - Ray player (or burner). They are on the market yet and available at Toshiba (or, say, eBay)? What should I look for?

  The HD-DVD player is a cool historical anachronism, but Blu - Ray will probably be a little more useful for me in the future.

  Cheers for the help.

  Hello

  As far as I know, there are some Blueray drives on the market that can be used in the notebook. But the fact is that not all readers are compatible because different master/slave/c-salt settings.

  I didn t find information on compatible BR readers. I guess you will have to test it yourself.

  I found this thread:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?MessageID=123271&

  The last guys has updated the own X 200 with a LG blueray and it worked

• Help with the driver DvD Ram for satellite P10

  On my laptop (satellite p10) is Windows 2000 Professional running, but the driver DVD Ram of the Toshiba Homepage does not...
  Where can I get a driver that works on my laptop?

  Hi Val,

  The correct driver for your laptop running Wnidows 2000 should be version 3.0.8.0 and is available for download from the Web from Toshiba website.

  I presume that it is the one that you tried, so I don't know what you mean when you say that "it doesn't."

• PAGE_FAULT_IN_NONPAGED_AREA___Msg DISK_0? Block 8: can? t read, replace the drive or remove the writing (Dell Dignostic softare scan) _ Protection

  I had purchase Dell inpiron 910 mini two years before now out of warranty. I got error on blue screen and then I restart the machine, I got the mode without failure when starting in safe mode, it stops and a disk read error occurred press Ctr + alt + del to restart I could even not to format the machine. could not start for winodow cd. Same blue screen message when starting from the cd, the message is as below
  A problem has been detected and windows has shut down to prevent damage to your computer.

  The problem seems to be caused by the following file: partmgr.sys

  PAGE_FAULT_IN_NONPAGED_AREA

  If this is the first time you've seen this stop error screen,

  Restart your computer. If this screen appears again. follow these steps:

  check to make sure any new hardware or software is installed correctly.

  If it is a new installation. Ask the manufacturer of your hardware or software for any windows update you might need.

  If the problem persists. disable or remove any newly installed hardware or software. Disable BIOS memory option such as caching or shading if you need to use safe mode to remove or disable components, restart your computer, press F8 to select advanced startup options. then select Safe mode.

  Technical information:

  STOP: 0 X 00000050 (0XF7895726, 0X00000000, 0X00000000)

  Partmgr.sys - address F7895726 base at F7893000, DateStamp 00000000

  I ran the Dell cd dignostic is to show the following error message:
  Error Code 0F00:1344

  MSG DISK_0? Block 8: can? t read, replace the drive or remove the write protect

  The given error code and message can use Dell Technical Support to help diagnose the problem.

  Hello

  ·        Since when are you facing this problem?

  ·        Remember to make changes to the system?

  I suggest to unplug external devices such as printer, scanner, etc. that are plugged into the system, and then restart the system and check if the problem persists.

  Error code 0F00:1344 you listed are hard drive error codes. Usually, this means that the hard drive needs to be replaced. I suggest you to contact Dell support for assistance. Once the hard disk is fixed, you can try the methods mentioned below.

  Click on the link below, contact Dell technical support.

  http://en.community.Dell.com/support-forums/disk-drives/default.aspx

  Method 1:

  I suggest you to do a check disk from the recovery console and check if the problem is resolved. Follow the steps mentioned below.

  a. start into the recovery console using the XP CD. Follow the steps mentioned in the article below.

  Description of the Windows XP Recovery Console for advanced users

  http://support.Microsoft.com/kb/314058

  b. perform a disk check.

  How to perform disk error checking in Windows XP

  http://support.Microsoft.com/kb/315265

  Method 2:

  I suggest you to start with the XP CD and then do a system restore. Follow the steps mentioned in the article below.

  How do I recover from a corrupted registry that prevents Windows XP startup

  http://support.Microsoft.com/kb/307545

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• Have installed Photoshop CS4. Replaced the drive hard and now I get error code 150:30. What should I do to get it working again

  Have installed Photoshop CS4. Replaced the drive hard and now I get error code 150:30. What should I do to get it working again

  Migration of CS4 breaks the license. That's what 150:30 means. Assuming you are using a Mac.

  You can use the Terminal method to repair the license... but I stress that carefully read you and understand the instructions here before you run it. beginning

  # 11. https://forums.Adobe.com/thread/1714695

  If this isn't what you want to do, you have to reinstall.

  Gene

• Satellite Pro A40: CD-RW/DVD drive cannot read DVD

  Hello

  The reader combo CD-RW/DVD on my Satellite Pro A40 (14 months) stopped reading DVDs (DVD - R or the video, have not tried other types), although it can play DVDs some time. I've cleaned the disc by using a cleaning disc. I think the problem started when I upgraded the OS to WinXP SP1 to SP2, but not sure. I tried CD - R and CD - RW writing and no errors were reported, but the CD that result are unusable (can't be read in the drive, with the LED blinks a few times and then to infinity).

  Someone has an idea how solve this ptoblem? Thank you

  Richard

  Hi Richard,

  I suggest that you go the Device Manager on your laptop and then remove your devive DVD-ROM in the list. When you have done this and then select the option "Find new hardware" and allow Windows XP Reinstall the device and associate the appropriate driver.

  HTH

• The driver installation fails after custom Windows 7 Pro install

  Hi all.  I just replaced the drive hard on my ProBook s 4440 as the original, one crashed unexpectedly.  I then reinstalled Windows 7 Professional but now have no way to connect to the internet.  I installed the driver of "Sierra Wireless Driver Package for add-on unit high flow Mobile HP un2430", but I still see the message "no connection is available" when I try to connect to my wireless network.  By Device Manager, I'm still missing the drivers for the following (hardware IDS are in brackets):

  (PCI\VEN_197B & DEV_2392 & SUBSYS_17F3103C & REV_30) base system device

  (PCI\VEN_10EC & DEV_8168 & SUBSYS_17F3103C & REV_07) Ethernet controller

  (PCI\VEN_1814 & DEV_539A & SUBSYS_1839103C & REV_00) network controller

  Controller of communication Simple PCI (PCI VEN_8086 & DEV_1E3A & SUBSYS_17F3103C & REV_04)

  (PCI VEN_8086 & DEV_1E31 & SUBSYS_17F3103C & REV_04) USB controller

  Any help or advice would be greatly appreciated.  Thank you!

  Hello:

  You need the following drivers:

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5229486&prodNameId=5229488&swEnvOID=4059&swLang=13&mode=2&taskId=135&swItem=ob-111787-1

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5229486&prodNameId=5229488&swEnvOID=4059&swLang=13&mode=2&taskId=135&swItem=ob-111305-1

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5229486&prodNameId=5229488&swEnvOID=4059&swLang=13&mode=2&taskId=135&swItem=ob-116003-1

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5229486&prodNameId=5229488&swEnvOID=4059&swLang=13&mode=2&taskId=135&swItem=ob-110949-1

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5229486&prodNameId=5229488&swEnvOID=4059&swLang=13&mode=2&taskId=135&swItem=ob-113862-1

• Satellite Pro A40: Is it possible to format the HARD drive without disk

  I am passing on a Satellite Pro A40 to a brother. It is in very good condition, but has slowed down over the years. I want to get rid of my data (I have on a new machine) and speed up the system by formatting the hard drive.

  The machine didn't come with a disc for Windows XP, or a recovery CD (just a CD "tools and utilities"). I'm sure the drive HARD will be partitioned, and I can format the drive without such a disc.

  If this is true, how should I do?
  Thank you.

  Hello

  I can't believe that you do not have recovery media.
  The laptop must be supplied with recovery CD, Tools & Utilities CD, and WinDVD.

  But back to your question;
  If you insert a new HARD disk, you will need to use the Toshiba Recovery CD or the original CD of Microsoft Windows to install the operating system.
  The new drive is not partitioned HARD and doesn't have any OS pre-installed!

  If you n t have the original CD of Microsoft OS you can contact the service provider allowed in your country and you can order it.

  I hope I could help

  Good bye

• Satellite Pro A40 guard stop with the ATI driver error message

  My girls having some problems with her laptop and get back to Uni at the end of week for me to have a look on.

  Basically, he keeps closing sometimes with an ATI graphics driver error message. I had updated the memory last Christmas and resinstalled from scratch.

  My first impressions are it is overheating and I probably need to clean the fan, was wondering if anyone had any ideas?

  Thank you very much
  Keith (South end)

  Satellite Pro A40 is about 3 years old and it is possible that the unit needs to be cleaned. If the appliance is used intensively, I assume that there is more dust inside. By overheating of the appliance stops suddenly without any warning.

  As a first step the device. I don't know if it's the right idea to do it alone, but if you are familiar with laptops, you can give a try. After having done that, your daughter should carefully watch what happens the next few days.